RKI Instruments 35-3001A-08-03 Owner's manual

Brand: RKI Instruments

Model: 35-3001A-08-03

Category: Carbon monoxide (CO) detectors

Type: Owner's manual

www.rkiinstruments.com

35-3001A-08-03

Methane/Carbon Monoxide

Sample-Draw Detector

Operator’s Manual

Part Number: 71-0412

Revision: 0

Released: 8/8/17

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

WARNING

Read and understand this instruction manual before operating

detector. Improper use of the detector could result in bodily harm

or death.

Periodic calibration and maintenance of the detector is essential

for proper operation and correct readings. Please calibrate and

maintain this detector regularly! Frequency of calibration

depends upon the type of use you have and the sensor types.

Typical calibration frequencies for most applications are between

3 and 6 months, but can be required more often or less often

based on your usage.

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Product Warranty

RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in materials,

workmanship, and performance for a period of one year from date of shipment from RKI

Instruments, Inc. Any parts found defective within that period will be repaired or replaced, at our

option, free of charge. This warranty does not apply to those items which by their nature are subject

to deterioration or consumption in normal service, and which must be cleaned, repaired, or replaced

on a routine basis. Examples of such items are:

Warranty is voided by abuse including mechanical damage, alteration, rough handling, or repair

procedures not in accordance with the operator’s manual. This warranty indicates the full extent of

our liability, and we are not responsible for removal or replacement costs, local repair costs,

transportation costs, or contingent expenses incurred without our prior approval.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER

WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED, AND

ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF RKI

INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN

NO EVENT SHALL RKI INSTRUMENTS, INC. BE LIABLE FOR INDIRECT,

INCIDENTAL, OR CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND

CONNECTED WITH THE USE OF ITS PRODUCTS OR FAILURE OF ITS

PRODUCTS TO FUNCTION OR OPERATE PROPERLY.

This warranty covers instruments and parts sold to users by authorized distributors, dealers, and

representatives as appointed by RKI Instruments, Inc.

We do not assume indemnification for any accident or damage caused by the operation of this gas

monitor, and our warranty is limited to the replacement of parts or our complete goods.

a) Absorbent cartridges d) Batteries

b) Pump diaphragms and valves e) Filter elements

c) Fuses

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

External Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Internal Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mounting the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting the Sample Lines to the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Wiring the Sample-Draw Detector to a Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introducing Incoming Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Replacing Components of the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the Low Flow Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Removing the Particle Filter’s Tubing Stub, if Necessary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Calibration Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Calibration, IR CH

Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Preparing for Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Setting the Response Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Returning to Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Calibration, CO Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Preparing for Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Setting the Response Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Returning to Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 1

Overview

This operator’s manual describes the 35-3001A-08-03 methane/carbon monoxide sample-draw

detector. This manual also describes how to install, start up, maintain, and calibrate the sample-

draw detector when using it with a gas monitoring controller. A parts list at the end of this manual

lists replacement parts and accessories for the sample-draw detector.

Specifications

Table 1 lists specifications for the methane/carbon monoxide sample-draw detector. See the

controller Operator’s Manual for information specific to the controller.

WARNING: When using the 35-3001A-08-03, you must follow the instructions and warnings

in this manual to assure proper and safe operation of the 35-3001A-08-03 and to

minimize the risk of personal injury. Be sure to maintain and periodically

calibrate the 35-3001A-08-03 as described in this manual.

Table 1: Specifications

Target Gases and Detection Range Methane: 0 - 100% volume

Carbon Monoxide: 0 - 300 ppm

Input Power 24 VDC Nominal (18.5 VDC - 30 VDC)

Construction (housing) Fiberglass/polyester (NEMA 4X)

Dimensions 8.5 in. H x 6.5 in. W x 4.25 in. D

Weight 4.5 lbs.

Sampling Method Sample-draw

Sample Flow 3.0 SCFH typical, with no inlet or exhaust line

Flow to Sensor 1.0 SCFH (nominal)

Low Flow Setpoint 0.6 ± 0.1 SCFH

Maximum Recommended Inlet/

Exhaust Line Length for

1/4” O.D. x 1/8” I.D. Tubing

Inlet

Exhaust

50 feet 0 feet

* RKI Instruments, Inc. does not recommend installing this tubing

size on both the inlet and exhaust.

Maximum Recommended Inlet/

Exhaust Line Length for

1/4” O.D. x 0.170” I.D. Tubing

Inlet

Exhaust

50 feet 50 feet

75 feet 0 feet

Response Time 90% in 30 seconds

Accuracy Methane

± 5% of reading or ± 2% of full scale (whichever is greater)

Carbon Monoxide

± 5% of reading or ± 5 ppm CO (whichever is greater)

2 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Description

This section describes the components of the methane/carbon monoxide sample-draw detector.

Figure 1: Methane/Carbon Monoxide Sample-Draw Detector Component Location

Pump

CO Sensor

(inside block)

Pump Connector

LEL

GBR

PWR/SIG

IR CH4

Sensor PCB

CO Flow

Block

IR CH4 Sensor

(inside block)

SensorFlow

Control Valve

Fail LED

Pilot LED

Flowmeter

Pump Reset

Switch

AMP 2

S S

AMP 1

OXY

AMP O XYAMP 2

This End To

Inlet Fitting

Hydrophobic

Filter

IR CH4

Flow Block

Oxygen

Sensor

Terminal

Strip

Particle Filter

Interconnect

Terminal

Strip

Charcoal

Filter

Flowmeter Circuit

BoardConnector

Inlet

Fitting

Exhaust

Fitting

LEL /IR

3/4" Conduit Hub

CO Amplifier

INLET

EXHAUST

Mounting Foot,4X

IR CH4 Amplifier

G B

Pressure Switch

Adjustment Screw

(behind PCB)

Detector/Amp

Terminal S trip

(Factory Wired)

S R

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 3

External Components

This section describes the sample-draw detector’s external components.

Housing

The sample-draw detector’s fiberglass housing is weather- and corrosion-resistant. It is suitable for

installation where general purpose equipment is in use.

The housing door is hinged on the left side and is secured by two latches on the right side. The

flowmeter and status LEDs are visible through a window in the housing door.

Four mounting feet are attached to the back of the housing (one at each corner). Use the mounting

feet to install the housing to a vertical surface.

Sample Fittings

The sample fittings are located on the left side of the bottom of the housing. The inlet fitting is near

the front of the housing and the exhaust fitting is near the back of the housing. The sample fittings

accept 1/4 in. rigid tubing. See the Installation section on page 8 to connect tubing to the sample

fittings.

Particle Filter

A particle filter with a tubing stub on one end is shipped with the instrument but it is not factory

installed. If the particle filter is installed directly to the inlet fitting, the tubing stub must be used. If

the particle filter is installed somewhere else, like at the end of the inlet line, the tubing stub can be

used or removed.

Conduit Hub

One 3/4” conduit hub is located on the right side of the bottom of the housing. It is used for routing

wiring into the housing by using conduit or an appropriate cable bushing.

Internal Components

This section describes the sample-draw detector’s internal components (see Figure 1). Figure 2

illustrates how the gas sample moves through the flow system.

Figure 2: Methane/Carbon Monoxide Sample-Draw Detector Flow Diagram

Restrictor

Pump

IR CH4

Sensor

Carbon

Monoxide

Sensor

Flowmeter

Particle Filter

Sensor Flow

Control Valve

Exhaust

Flowmeter PCB

Pressure Switch

Hydrophobic Filter

Inlet

Charcoal

Filter

4 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Main Circuit Board

The main circuit board includes the detector/amp terminal strip, interconnect terminal strip, oxygen

sensor terminal strip, pump connector, and flowmeter circuit board connector (see Figure 1).

Detector/Amp Terminal Strip

The detector/amp terminal strip is the upper twelve-point terminal strip in the bottom right corner

of the main circuit board. Use the detector/amp terminal strip to connect the IR CH

amplifier and

the CO amplifier to the main circuit board.

NOTE: The IR CH

amplifier and CO amplifier are factory-wired to the main circuit board. See

the “Installation” section on page 8 for all wiring procedures related to the sample-draw

detector.

Interconnect Terminal Strip

The interconnect terminal strip is the lower twelve-point terminal strip in the bottom right corner of

the main circuit board. Use the interconnect terminal strip to connect the sample-draw detector to a

controller.

Oxygen Sensor Terminal Strip

The oxygen sensor terminal strip is a two-point terminal strip in the upper right corner of the main

circuit board. This terminal strip is not used in this version of the sample-draw detector.

Pump Connector

The pump connector is the two-point connector below the oxygen terminal strip in the upper right

corner of the main circuit board. Use the pump connector to connect the pump to the main circuit

board.

NOTE: The pump is factory-wired to the main circuit board. See “Installation” on page 8 for all

wiring procedures related to the sample-draw detector.

Flowmeter Circuit Board Connector

The flowmeter circuit board connector is a six-position connector in the upper left corner of the

main circuit board. Use the flowmeter circuit board connector to connect the flowmeter circuit

board to the main circuit board.

NOTE: The flowmeter circuit board is factory wired to the main circuit board. See “Installation”

on page 8 for all wiring procedures related to the sample-draw detector.

Flowmeter Circuit Board

The flowmeter circuit board is mounted to the left side of the main circuit board using standoffs. It

includes the flowmeter, sensor flow control valve, status LEDs, pressure switch, and pump reset

switch.

Flowmeter

The flowmeter is mounted to the right side of the flowmeter circuit board. You can see it through

the window in the door. A ball in the flowmeter column indicates the flow rate to the sensor. The

flowmeter measures the flow in the range 0.2 to 2.0 SCFH (Standard Cubic Feet per Hour). The

optimum flow rate is 1.0 SCFH.

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 5

Sensor Flow Control Valve

The sensor flow control valve is mounted to the flowmeter circuit board above the flowmeter. The

sensor flow control valve adjusts the flow rate to the detector. Turn the valve’s knob clockwise to

increase the flow and counterclockwise to decrease the flow.

Status LEDs

Two status LEDs are above the flowmeter. They are also visible through the window in the housing

door. The green Pilot LED is on when the sample-draw detector is receiving power from the

controller. The red Fail LED is on when the sample flow rate is below the low flow level.

Pressure Switch

The pressure switch is mounted to the back of the flowmeter circuit board. The pressure switch

monitors the flow rate of the incoming gas sample.

If the flow rate falls below the preset low flow level, the pressure switch causes the Fail LED to

turn on and interrupts the signal from the detector. The interrupted detector signal causes a fail

condition at the controller. The low flow level is factory-set at 0.6 SCFH (±0.1 SCFH). See

“Adjusting the Low Flow Setting” on page 20 to adjust this setting.

Pump Reset Switch

The pump reset switch is located to the left of the status LEDs. When a low flow condition occurs,

the pump will be shut off. To reset the low flow condition and start the pump again, press and hold

the pump reset switch for about 2 seconds, then release.

Hydrophobic Filter

The hydrophobic filter is located toward the bottom left of the main circuit board. The filter

prevents particulates and water in the incoming gas sample from damaging the flow and detection

systems. Replace the filter when it appears dirty, discolored, or clogged.

Pump

The pump is mounted to the right side of the main circuit board. The pump pulls the gas sample

into the sample-draw detector. The pump operates on 24 VAC, which is generated from the 24

VDC supplied by the controller.

Charcoal Filter

A charcoal filter is located at the top of the main circuit board. It scrubs out interfering gases which

may cause the CO sensor to respond, such as H

S or certain hydrocarbons. Replace the charcoal

filter when false high CO readings are noticed, especially in the presence of H

IR CH

Sensor/IR CH

Sensor PCB

The methane sensor is an infrared type plug-in detector. It is installed in the IR CH

flow block and

the IR CH

flow block is mounted to the middle of the main circuit board. It is the lower of the two

flow blocks mounted to the main circuit board. A small circuit board, the IR CH

sensor PCB, with

a 4-wire cable mates to the IR CH

sensor and retains it in the flow block. The cable is wired to the

IR CH

amplifier. The IR CH

sensor PCB allows you to replace the sensor without disconnecting

the wiring.

6 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

IR CH

Amplifier

The IR CH

amplifier converts the electrical output from the IR CH

sensor to a 4 to 20 mA signal

that corresponds to the detection range and transmits the signal to a gas monitoring controller. A

label on the amplifier indicates the detector drive current. This drive current is factory set. The

amplifier is mounted on the top middle edge of the main circuit board. It consists of the zero pot,

span pot, controller terminal strip, detector terminal strip, and test points.

Figure 3: IR CH

Amplifier Component Location

Zero Pot

The zero pot is located in the upper right corner of the amplifier (see Figure 3). Use a small flat

blade screwdriver to turn the zero pot’s adjustment screw and adjust the amplifier’s zero (fresh air)

output during the start-up and calibration procedures. Turn the adjustment screw clockwise to

increase the fresh air output and counterclockwise to decrease the fresh air output.

Span Pot

The span pot is located below the zero pot (see Figure 3). Use a small flat blade screwdriver to turn

the span pot’s adjustment screw and adjust the amplifier’s gas response output during the

calibration procedure. Turn the adjustment screw clockwise to increase the span output and

counterclockwise to decrease the span output.

CAUTION: The amplifier includes additional pots. They are factory-set. Do not adjust them.

Controller and Detector Terminal Strips

The controller terminal strip and detector terminal strip are three- and four-position plug-in style

terminal strips, respectively. The controller terminal strip is located on the right side of the

amplifier and the detector terminal strip is to the left of it. Both terminal strips are factory wired to

the sensor and main circuit board.

Test Points

The test points are on the left side of the amplifier (see Figure 3). The test points produce a 100 mV

to 500 mV output that corresponds to the sample-draw detector’s 4 to 20 mA output. Use the test

points and a voltmeter to measure the amplifier’s output during the start-up and calibration

procedures. The black test point in the upper left corner is the negative (-) test point and the red test

point to the left of the zero and span pots is the positive (+) test point.

Factory Set Pots

Sensor

Current

148mA

LEL

GBR

Test Points

100-500 mV Range

Zero Pot

Detector

Terminal Strip

Span Pot

Controller

Terminal Strip

PWR / SIG

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 7

Carbon Monoxide Sensor/CO Amplifier

The carbon monoxide sensor is a plug-in sensor that plugs into the back of the CO amplifier. The

sensor and amplifier are retained in the flow block by two screws. The flow block is mounted to the

middle of the main circuit board. It is the higher of the two flow blocks mounted to the main circuit

board.

Through a series of chemical and electronic reactions, the CO sensor produces a millivolt output

that is proportional to the detection range of the sample-draw detector. A red wire and a blue wire

extend from the CO amplifier and allow connection to the detector/amp terminal strip.

Figure 4: CO Amplifier Component Location

Zero Pot

The zero pot is located in the lower right corner of the amplifier (see Figure 4). Use a small flat

blade screwdriver to turn the zero pot’s adjustment screw and adjust the amplifier’s zero output

during the start up and calibration procedures. Turn the adjustment screw clockwise to increase the

zero output and counterclockwise to decrease the zero output.

Span Pot

The span pot is located to the left of the zero pot (see Figure 4). Use a small flat blade screwdriver

to turn the span pot’s adjustment screw and adjust the amplifier’s gas response during the

calibration procedure. Turn the adjustment screw clockwise to increase the span output and

counterclockwise to decrease the span output.

Test Points

The test points are on the top edge of the amplifier (see Figure 4). The test points produce a 100 mV

to 500 mV output that corresponds to the sample-draw detector’s 4 to 20 mA output. Use the test

points and a voltmeter to measure the amplifier’s output during the start-up and calibration

procedures. The black test point (CAL 2) in the upper left corner is the negative (-) test point and

the red test point (CAL 1) in the upper right corner is the positive (+) test point.

Zero Pot

Span Pot

Test Points

100-500 mV Range

8 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Installation

This section describes procedures to mount the sample-draw detector in the monitoring

environment and wire the sample-draw detector to a controller.

Mounting the Sample-Draw Detector

1. Select the mounting site. Consider the following when you select the mounting site:

• Is there enough room to open the housing door and make wiring and tubing connections at

the bottom of the housing?

• Make sure there is sufficient room to perform start-up, maintenance, and calibration

procedures.

• Are the flowmeter and status LEDs visible?

Figure 5: Outline and Mounting Dimensions

Ø.30x.50(4X)MOUNTING

.78

1.13

.40

Pilot Fail

.85

.80

4.50

NOTE: Housing is4.3 inchesdeep

8.88

4.00

6.50

35-3001

www.rkiinstruments.com

Sample Drawing

Gas Detector

8.50

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 9

2. Close and latch the housing door.

NOTE: The sample-draw detector is shipped with the mounting feet “tucked under” the housing

to protect the mounting feet during shipment.

3. Slightly loosen the screw that secures the mounting foot to the housing, then rotate the

mounting foot 180 degrees (see Figure 5).

4. Tighten the screw that secures the mounting foot to the housing.

5. Repeat steps 3 and 4 for the remaining three mounting feet.

6. Position the sample-draw housing on a vertical surface at eye level (4 1/2 to 5 feet from the

floor).

7. Insert 1/4 inch screws through the slots in the mounting feet to secure the housing to the

mounting surface.

Connecting the Sample Lines to the Sample-Draw Detector

See Figure 7 for the fitting layout.

Installing the Inlet Line with Particle Filter Connected to the Inlet Fitting

1. Loosen the nut on the inlet fitting until 3 threads are visible.

2. Push the particle filter’s tubing stub into the inlet fitting until it stops. Be sure the arrow on the

particle filter is pointing toward the inlet fitting.

3. Hand tighten the nut on the inlet fitting so the ferrules clamp on the tubing. If the tube nut is

removed, see Figure 7 for the arrangement of the fitting components.

4. Connect a length of sample tubing to the other side of the particle filter and route it to the

sampling area. 1/4” O.D. rigid polypropylene, Teflon, or flexible polyurethane tubing may be

used. RKI Instruments, Inc. recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x

0.170” I.D. tubing based on your length requirements. See “Specifications” on page 1 for

maximum tubing lengths based on tubing size.

CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate

insert if necessary to provide support to the tubing and ensure a good seal when

connecting to the flexible stub on the filter.

CAUTION: Avoid loops or slumps in the incoming sample line. To reduce response time, keep the

incoming sample line as short as possible.

Installing the Inlet Line without Particle Filter Connected to the Inlet Fitting

1. Loosen the nut on the inlet fitting until 3 threads are visible.

2. Push 1/4” O.D. rigid polypropylene or rigid Teflon sample tubing into the fitting until it stops.

Flexible polyurethane tubing may be used with an appropriate insert. RKI Instruments, Inc.

recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x 0.170” I.D. tubing based on your

length requirements. See “Specifications” on page 1 for maximum tubing lengths based on

tubing size.

CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate

insert to seal the connection between the tubing and the inlet fitting.

10 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

3. Hand tighten the nut on the inlet fitting so the ferrules clamp on the tubing. If the tube nut is

removed, see Figure 7 for the arrangement of the fitting components.

4. Route tubing from the inlet fitting to the sample area. See “Specifications” on page 1 for

maximum tubing lengths based on tubing size.

CAUTION: Avoid loops or slumps in the incoming sample line. To reduce response time, keep the

incoming sample line as short as possible.

5. If desired, install the particle filter onto the end of the inlet line. Be sure the arrow on the

particle filter is pointed toward the inlet line.

Installing the Exhaust Line

1. Loosen the nut on the exhaust fitting until 3 threads are visible.

2. Push 1/4” O.D. rigid polypropylene or rigid Teflon sample tubing into the fitting until it stops.

Flexible polyurethane tubing may be used with an appropriate insert. RKI Instruments, Inc.

recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x 0.170” I.D. tubing based on your

length requirements. See “Specifications” on page 1 for maximum tubing lengths based on

tubing size.

CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate

insert to seal the connection between the tubing and the inlet fitting.

3. Hand tighten the nut on the exhaust fitting so the ferrules clamp on the tubing. If the tube nut is

removed, see Figure 7 for the arrangement of the fitting components.

4. Route the opposite end of the tubing to an open area where the sample can safely disperse or to

an exhaust duct. See “Specifications” on page 1 for maximum tubing lengths based on tubing

size.

Wiring the Sample-Draw Detector to a Controller

WARNING: Always verify that the controller is off and that power to the controller is

off before you make wiring connections.

1. Turn off the controller.

2. Turn off power to the controller.

3. Unlatch and open the housing door of the sample-draw detector.

4. Guide a five-conductor, shielded cable or five wires in conduit through the conduit hub at the

bottom of the sample-draw housing. A minimum of 18 AWG wire is recommended.

5. Connect the cable to the sample-draw detector’s interconnect terminal strip as shown in Figure

6. Close and latch the housing door of the sample-draw detector.

CAUTION: If using shielded cable, leave the cable shield’s drain wire insulated and

disconnected at the sample-draw detector. You will connect the opposite end of the

drain wire at the controller.

7. Route the cable or wires in conduit leading from the sample-draw detector through one of the

conduit hubs at the controller.

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 11

8. Connect the wires to the applicable detector/transmitter terminal strip at the controller as

shown in Figure 6. Refer to the controller operator’s manual and the controller detector head

specification sheet for the 35-3001A-08-03 for detector/terminal strip connections specific to

the controller.

Figure 6: Wiring the Sample-Draw Detector to a Controller

9. If shielded cable is used, connect the cable’s drain wire to an available chassis (earth) ground at

the controller. RKI controllers typically have a ground stud that can be used to ground the

cable’s drain wire.

Black

White

Red

Not Usedon

This Version

SP AN

ZER O

Red (+)

Blue (S)

PWR / SIG

Green

Black

Red

LEL/IR

AMP 2AMP 1

AMP 1 AMP 2

PATS201PATS201

White

PATS101PATS101

IR CH4

Sensor

OXY

- (DC Ground)

Controller or Recording Device

4/20 Signal

+24VDC

4/20 Signal

+24VDC

IR CH4

LEL

Sensor

Current

148mA

IR CH4

Sensor PCB

12 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Start Up

This section describes procedures to start up the sample-draw detector and place the sample-draw

detector into normal operation.

Introducing Incoming Power

1. Complete the installation procedures described earlier in this manual.

2. Verify that the wiring is correct and secure. Refer to the controller operator’s manual for

connections at the controller.

3. Turn on or plug in the power to the controller, then turn on the controller.

4. Verify that the sample-draw detector’s Pilot LED is on.

5. Verify that the controller is on and operating properly. Refer to the controller operator’s

manual.

NOTE: When first powered up, the sample-draw detector will enter about a one minute period

when the 4-20 mA output is stabilizing and may be above the controller alarm points or

well below zero momentarily. RKI controllers have a one minute warmup period when

the controller does not display any gas reading or give any alarm indication. The CO

transmitter’s 4-20 mA signal should be stable by the time the controller’s warmup period

is over.

6. Verify that the flowmeter indicates a flow rate of approximately 1.0 SCFH. If necessary, use

the sensor flow control valve to adjust the flow rate. Turn the valve’s knob clockwise to

increase the flow and counterclockwise to decrease the flow.

NOTE: The following step tests for leaks in the sample line. This test will cause a low flow

condition at the sample-draw detector and a fail condition at the controller. Be sure to put

the controller into its calibration program or disable external alarms before performing

this test.

7. Verify that the incoming sample line is not leaking. To test the sample line, press and hold the

reset switch and plug the open end of the sample line with your thumb. If the flowmeter ball

drops to the bottom of the flowmeter, the incoming sample line is not leaking.

8. Remove your thumb from the sample line, release the reset switch, and verify the flowmeter

returns to a normal flow rate.

9. Enable alarms or place the controller in normal operation.

CAUTION: Allow the sample-draw detector to warm up for 5 minutes before you continue with

the next section, “Setting the Zero Reading.”

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 13

Setting the Zero Reading

CAUTION: If you suspect the presence of combustible or toxic gas or an abnormal oxygen

concentration in the monitoring environment, use the calibration kit and the zero air

calibration cylinder to introduce “fresh air” to the sensor and verify an accurate

zero setting. See “Calibration, IR CH

Sensor” on page 22 and “Calibration, CO

Sensor” on page 24 for instructions on using a zero air calibration cylinder for

setting the zero reading.

1. Verify that the sample-draw detector is sampling a fresh air environment (environment known

to be free of combustible and toxic gas and of normal oxygen concentration, 20.9%).

2. Verify a reading of 0 %vol for the methane channel and 0 ppm for the CO channel on the

controller display screen for the applicable channel.

If the display reading is 0 %vol for the methane channel and 0 ppm for the CO channel, start up

is complete. The sample-draw detector is in normal operation. If the display reading is not

0 %vol for the methane channel or 0 ppm for the CO channel, continue with step 3.

3. Perform a zero (fresh air) operation at the controller. See “Calibration, IR CH

Sensor” on

page 22 and “Calibration, CO Sensor” on page 24 for instructions to perform a zero (fresh air)

operation.

Maintenance

This section describes maintenance procedures. It includes preventive maintenance procedures.

This section also includes procedures to troubleshoot the sample-draw detector, replace

components of the sample-draw detector, adjust the low flow setting, and remove the particle

filter’s tubing stub.

Preventive Maintenance

This section describes a preventive maintenance schedule to ensure the optimum performance of

the sample-draw detector. It includes daily, monthly, and quarterly procedures.

Daily Visual Checks

1. Verify that the Pilot LED is on.

2. Verify that the flowmeter indicates a flow rate of approximately 1.0 SCFH. If necessary use the

sensor flow control valve to adjust the flow rate to 1.0 SCFH. Turn the valve’s knob clockwise

to increase the flow and counterclockwise to decrease the flow.

3. Verify a display reading of 0 %vol for the methane channel and 0 ppm for the carbon monoxide

channel at the controller. Investigate significant changes in the display reading.

14 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Monthly Response Test

This procedure describes a test to verify that the sample-draw detector responds properly to the

target gas.

NOTE: To reduce the response time of this test, use a short incoming sample line. If the sample-

draw detector’s sample line is long, connect a shorter line for this test. Make sure you

reconnect the sample line after you complete this procedure.

NOTE: Performing a response test on the sample-draw detector may cause alarms. Be sure to put

the controller into its calibration program or disable external alarms before performing

this test.

Preparing for the response test

NOTE: This procedure describes the RKI calibration kit that includes a demand flow regulator.

1. Verify that the display reading at the controller is 0 %vol for the methane channel and 0 ppm

for the carbon monoxide channel.

If the display reading is not 0 %vol for the methane channel or 0 ppm for the carbon monoxide

channel, set the zero reading as described in “Calibration, IR CH

Sensor” on page 22 or

“Calibration, CO Sensor” on page 24, then continue this procedure.

2. Set a voltmeter to measure in the millivolt (mV) range.

3. Open the housing door, then plug the voltmeter leads into the test points on the IR CH

amplifier.

Plug the positive lead into the red (+) test point; plug the negative lead into the black (-) test

point.

4. Use the following formula to determine the correct test points output for the test sample.

Output (mV) = (calibrating sample/fullscale) X 400 + 100

For example, with a test sample of 50 %volume and a fullscale setting of 100 %volume, the

correct output is 300 mV.

300 (mV) = (50/100) X 400 +100

Performing the response test

1. Screw the demand flow regulator into the methane cylinder.

2. Connect the calibration tubing from the demand flow regulator to the inlet fitting. Gas will

begin to flow.

3. After approximately one minute, verify that the millivolt output at the IR CH

amplifier

stabilizes within ± 20% of the reading determined above. If the reading is not within ± 20% of

the determined value, calibrate the sample-draw detector as described in “Calibration, IR CH

Sensor” on page 22.

4. Unscrew the methane cylinder from the demand flow regulator.

5. Remove the voltmeter leads from the IR CH

amplifier.

35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector • 15

6. Plug the voltmeter leads into the test points on the CO amplifier.

Plug the positive lead into the red (+) test point; plug the negative lead into the black (-) test

point.

7. Use the following formula to determine the correct test points output for the test sample.

Output (mV) = (calibrating sample/fullscale) X 400 + 100

For example, with a test sample of 50 ppm CO and a fullscale setting of 300 ppm CO, the

correct output is 167 mV.

167 (mV) = (50/300) X 400 +100

8. Screw the demand flow regulator into the CO calibration cylinder.

9. Connect the calibration tubing from the demand flow regulator to the inlet fitting. Gas will

begin to flow.

10. After approximately one minute, verify that the millivolt output at the CO amplifier stabilizes

within ± 20% of the reading determined above. If the reading is not within ± 20% of the

determined value, calibrate the sample-draw detector as described in “Calibration, CO Sensor”

on page 24.

11. Unscrew the CO cylinder from the demand flow regulator.

12. Remove the calibration tubing from the inlet fitting.

13. Remove the voltmeter leads from the CO amplifier.

14. Close the housing door.

15. Store the calibration kit in a safe place.

16. Reconnect the sample tubing to the inlet fitting.

Quarterly Calibration

Calibrate the sample-draw detector as described in “Calibration, IR CH

Sensor” on page 22 and

“Calibration, CO Sensor” on page 24.

Troubleshooting

The troubleshooting guide describes symptoms, probable causes, and recommended action for

problems you may encounter with the sample-draw detector.

NOTE: This troubleshooting guide describes sample-draw detector problems only. See the

controller Operator’s Manual if the controller exhibits any problems.

Fail Condition

Symptoms

• The sample-draw detector’s Fail LED is on.

• The monitoring device is operating properly but indicates a reading well below zero.

Probable causes

• The sample-draw detector’s flow rate is too low because of an obstructed sample line, failed

pump, etc.

• The sample-draw detector is malfunctioning.

• The sensor wiring is disconnected or misconnected.

16 • 35-3001A-08-03 Methane/Carbon Monoxide Sample-Draw Detector

Recommended action

1. At the sample-draw detector, set the correct flow rate with the sensor flow control valve.

2. If you cannot set the correct flow rate, check the sample lines for obstructions or kinks.

3. Verify that the sensor wiring is correct and secure. “Wiring the Sample-Draw Detector to a

Controller” on page 10 describes sensor wiring connections.

4. Calibrate the sample-draw detector as described in “Calibration, IR CH

Sensor” on page 22

and “Calibration, CO Sensor” on page 24.

5. If the fail condition continues, replace the sensor(s) as described in “Replacing Components of

the Sample-Draw Detector” on page 16.

6. If the fail condition continues, contact RKI Instruments, Inc. for further instruction.

Slow or No Response/Difficult or Unable to Calibrate

Symptoms

• The sensor responds slowly or does not respond during the monthly response test.

• Unable to accurately set the zero or response reading during the calibration procedure.

• The sensor requires frequent calibration.

Probable causes

• The calibration cylinder is low, out-dated, or defective.

• If a demand flow regulator calibration kit is used, the demand flow regulator is not functioning

properly.

• The sample-draw detector’s flow rate is too low because of an obstructed sample line, failed

pump, etc.

• The sample-draw detector is malfunctioning.

Recommended action

1. Verify that the calibration cylinder contains an adequate supply of a fresh test sample.

2. If a demand flow regulator calibration kit is used, use a different demand flow regulator to

determine if the original one is functioning properly.

3. If necessary, set the correct flow rate with the sensor flow control valve.

4. If you cannot set the correct flow rate, check the sample line for obstructions or kinks.

5. If the calibration/response difficulties continue, replace the sensor as described later in this

section.

6. If the calibration/response difficulties continue, contact RKI Instruments, Inc. for further

instruction.

Replacing Components of the Sample-Draw Detector

This section includes procedures to replace the IR CH

sensor, IR CH

amplifier, carbon monoxide

sensor, carbon monoxide amplifier, charcoal filter, hydrophobic filter, and particle filter.

Replacing the IR CH

Sensor

1. Turn off the controller.

2. Turn off power to the controller.

3. Open the housing door of the sample-draw detector.

4. Unscrew and remove the four screws that secure the IR CH

sensor PCB, then lift the IR CH

sensor PCB and sensor off of the flow block.

Page is loading ...

RKI Instruments 35-3001A-08-03 Owner's manual

Brand: RKI Instruments

Model: 35-3001A-08-03

Category: Carbon monoxide (CO) detectors

Type: Owner's manual

Download PDF

report

RKI Instruments 35-3001A-08-03 Owner's manual

RKI Instruments 35-3001A-08-03 Owner's manual

Related papers

Other documents