Ohlins YA705 Mounting Instruction

Type
Mounting Instruction

This manual is also suitable for

© Öhlins Racing AB. All rights reserved. Any re-
printing or unauthorized use without the written
permission of Öhlins Racing AB is prohibited.
Printed in Sweden.
Mounting Instructions YA705_0 Issued 2007 01 10
These instructions and other documents
can be downloaded from
www.ohlins.com
Mounting Instructions
Kit Contents:
Part no. Pcs.
Shock absorber YA705 1
Bracket 20028-01 1
Screw MC6S 01046-01 2
Öhlins Sticker black 00191-13 2
Öhlins Sticker white 00191-20 2
Memo Notes 01180-01 1
Owner’s Manual 07241-02 1
Before installing this shock absorber,
check the contents of the kit listed
below. If anything is missing, please
contact your nearest Öhlins dealer.
SHOCK ABSORBER YA 705
for Yamaha XVS 1100A Drag Star Classic
During storage and transportation,
especially at high ambient tempera-
ture, some of the oil and grease used
for assembling may leak and stain
the packaging. This is in no way det-
rimental to the product, wipe off the
excessive oil/grease with a cloth.
Before installing this product, read the Öhlins Owner’s Manual!
I
ns
t
a
ll
in
g
a
s
ho
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
no
t
a
pp
r
o
v
ed
b
y
t
h
e
v
e
h
ic
le
m
an
u
fa
ct
ur
e
r
m
a
y
a
f
f
e
c
t t
h
e
sta
b
il
it
y
of
yo
u
r
ve
h
i
cl
e.
In
st
a
ll
ing
a
s
ho
c
k
a
b
s
o
r
ber
t
h
a
t
is
not
a
p
pr
ov
e
d
b
y
t
h
e
v
e
h
ic
l
e
m
a
n
u
fac
ture
r
m
a
y
a
f
f
e
c
t t
h
e
s
ta
b
i
l
it
y
of
y
ou
r
v
e
h
i
c
le
.
I
nst
a
lling
a
sh
o
c
k
a
b
s
o
rb
e
r
t
ha
t
is
n
o
t
a
p
p
r
o
v
ed
b
y
the
ve
h
ic
le
m
a
n
u
fa
c
t
u
r
e
r
m
ay
af
fe
ct
th
e
s
t
a
b
il
it
y
of
y
ou
r
ve
h
ic
le
.
In
sta
ll
ing
a s
h
oc
k a
b
s
orbe
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
veh
ic
l
e
m
a
n
u
fa
c
tur
e
r
m
ay
af
fec
t th
e
sta
b
il
it
y o
f
y
o
u
r v
e
h
ic
le
.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00 Fax +46 8 590 025 80
www.ohlins.com
WITH SET-UP DATA
Always ensure that the basic settings made by
Öhlins are intact.
Make sure that all screws are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the sus-
pension is fully compressed or extended.
19
(Right side) Reattach the starter solenoid to the
battery box and attach the unit to the vehicle.
Reconnect the battery and the right side cover.
20
Reinstall the cover. Reconnect the CDI box and
attach it with the screws.
21
Reattach the seat. Make sure that all removed
parts are installed in the same way as they
were before the installation.
ADJUSTMENTS
1
2
3
Set-up Data
Spring preload 13 mm
Rebound damping 14 clicks
Shock absorber length 304,5
+0
mm
Stroke 47,5 mm
Spring 21014-59
Free spring length 140
+0
1
2
-12
-3
3
Spring Preload
Turn the knob on the hydraulic preload
adjuster to set the spring preload. Turn
clockwise to increase the preload, turn
counter clockwise to decrease.
Rebound
Turn the wheel on the piston shaft above
the end eye/bracket. Turn clockwise to
increase damping, turn counter clockwise
to decrease.
NOTE!
When delivered the Öhlins shock absorber
is dialed to the recommended settings
for the specifi c vehicle model. If you have
changed the setting, reset according to the
following:
The adjuster has a right hand thread. Turn
the adjuster clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open
and count the clicks until you reach the
recommended number (see Set-up Data).
CAUTION!
Do not use force, delicate sealing surfaces
can be damaged. Handtighten only.
Length
We recommend you to adjust the length
before installing the shock absorber to
the vehicle. Use two wrenches. Hold the
upper nut with one hand and at the same time
loosen the lock nut (lower nut). Turn the end
eye/ bracket to the desired length. Lock the
lock nut. Tightening torque: 40 Nm
WARNING!
The adjustable end eye/bracket must not be
threaded out more than that the groove is fully
visible beneath the lock nut. This is maximum
length. After adjusting, make sure that the lock
nut is tightened.
3
HOW TO INSTALL
1
Put the motorcycle on a workstand so that the
rear wheel barely touches the ground.
WARNING!
Make sure the vehicle is securely supported so
that it will not tip.
2
Remove the seat.
3
Remove the CDI box (A) and detach the socket
(B). Remove the rivets and the cover (C).
4
Remove both side covers.
5
Remove the starter solenoid from the battery
box.
6
Disconnect the battery and remove it by
detaching the rubber strap. Detach the battery
box from the frame, without removing it.
7
Remove the engine cover from the left side of
the vehicle.
8
Without detaching its hoses, gently lift the fuel
lter from its fi xing points.
9
Remove the two screws indicated in the fi gure
above, and detach the two hoses, so that the
lid can be carefully folded out from the frame.
10
Loosen the screws on the triangle link and
push rods. Remove them in the given order in
the fi gure.
11
Gently fold out the lid on the left side so that
the upper screw of the original shock absorber
can be loosened. To remove the screw, gently
fold out the battery box on the right side.
12
Remove the original shock absorber down-
wards.
NOTE!
Recommendation! Before installing the Öhlins
shock absorber:
• clean the vehicle thoroughly
• adjust the length of the shock absorber (check
the headlight angle after adjusting the length!)
13
Install the Öhlins shock absorber from under-
neath the vehicle. Lead the hydraulic adjuster
between the frame and the wire harness as
indicated in the fi gure. Make sure the oil fi lling
screw on the shock absorber is pointing to the
rear.
1
2
4
5
6
8
1
2
3
Left side
14
Attach the upper screw of the Öhlins shock
absorber, reinstall the triangle link and push
rods, without tightening yet.
NOTE!
Lower the motorcycle so that the shock absorber
is sligthly compressed, before tightening the
screws.
15
Tighten the screws of the upper and lower at-
tachments, triangle link and push rods.
16
Reattach the lid, the two hoses and the fuel
lter. (See step 8-9)
.
Reattach the engine cover.
17
Attach the hydraulic adjuster to the bracket
provided in this kit. Use the screws to attach
the bracket to the cover. See fi gure.
18
Reattach the side cover on the left side.
oil fi lling screw
13
7
17
9
WARNING!
It is advisable to have an Öhlins dealer install the
shock absorber.
A
B
C
C
C
C
WARNING!
Make sure that the hydraulic preload adjuster
hose runs in soft bends. Also check that it does
not come in contact with the exhaust pipe or
any sharp edges.
  • Page 1 1
  • Page 2 2

Ohlins YA705 Mounting Instruction

Type
Mounting Instruction
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI