Page is loading ...
Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001e
SKU: STAND-V001E
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B (x1)
Clamp
C (x1)
Plastic Cap
M-A (x4)
M4x12
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D (x1)
Pole
E (x1)
Cable Clip
F (x1)
Grommet
Base
G (x5)
Rubber Pad
H (x1)
Bolt
M-B (x4)
M5x12
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
I (x1)
Grommet
Plate
J (x1)
5mm Allen
Wrench
K (x1)
6mm Allen
Wrench
M-C (x4)
D5 Washer
3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
17.6lbs
(7.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Attach plastic cap (C) to top of pole (D).
STEP 2
OPTION A: Clamp Installation
Stick rubber pads (G) to bottom of clamp (B) as shown in diagram. Align pin in clamp (B)
with bottom hole in pole (D). Attach pole (D) to clamp (B) using bolt (H) and 6mm allen
wrench (K). Mount clamp (B) to desktop using hand bolt.
D C
4
STEP 2 (Continued)
OPTION B: Grommet Installation
Remove hand bolt from clamp (B) by first removing phillips screw from top
of bolt, then remove plate and unscrew. Stick rubber pads (G) to bottom of
grommet base (F). Align pin in grommet base (F) with bottom hole pole (D).
Mount pole (D) and grommet base (F) to desktop using grommet plate (I) and
previously removed hand bolt.
STEP 3
G
F
B
I
10-75m
m
A
E
J
Slide cable management clip (E) and arm (A) over top of pole (D) and secure desired
height using 5mm allen wrench (J).
5
STEP 4
Insert screws (M-A or M-B) with washers (M-C) into top two
holes of monitor, leaving 3mm of thread exposed. Hang
monitor over slots in VESA plate. Secure using screws and
washers in bottom two holes, and tighten all screws.
TV
TV
TV
M-A/M- B
M- C
M-A/M- B
M- C
1
2
3m m
3
6
STEP 5
If needed, tighten tilt joint using 6mm allen wrench (K).
STEP 6
Store tools (K, J) in cable management clip (E) for future adjustments.
+45 °
-45°
K
J
K
7
STEP 7
Manage cables and adjust tilt and rotation of monitor as desired.
360°
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/