Simplicity 040394-00 User manual

Not for Reproduction

Generator Systems

317247 Revision G

rights reserved. LLC.

Generator Systems

Operator’s Manual

Not for Reproduction

Thank you for purchasing this quality-built Briggs & Stratton® standby generator. We are pleased that you’ve

placed your confidenc Briggs & Stratton. When operated and maintained according to the instructions in this

manual, your Briggs & Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby

generators and how to avoid them. This product is only for use as an optional generator system which provides an

alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication

systems that, when stopped during any power outage, could cause discomfort or inconvenience.

Save these original instructions for future reference.

This standby generator requires professional installation before use. Refer to the separate Installation

manual for instructions on safe installation procedures. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow

Pages. There are thousands of Briggs & Stratton authorized service dealers worldwide who provide quality

service. You can also contact Technical Service by phone at 800-732-2989 between 8:00 AM and 5:00 PM CT.,

or by e-mail at [email protected], or click on Find a Dealer at BRIGGSandSTRATTON.COM, which

provides a list of authorized dealers.

Generator and engine model and serial numbers should be recorded in the installation manual.

DATE OF PURCHASE

GENERATOR

Model Number

Model Revision

Serial Number

ENGINE

Not for Reproduction

3

Table of Contents

Important Safety Instructions........................4

Installation ....................................7

Owner Orientation ............................................7

Fuel Factors .................................................8

Delivery Inspection...........................................10

Controls ..................................... 11

Access Panels ..............................................13

System Control Panel.........................................15

Operation .................................... 19

Engine Oil..................................................19

Battery ....................................................19

15 Amp Fuse ...............................................19

Automatic Operation Sequence .................................19

Maintenance .................................. 20

Service Code Detection System .................................20

Generator Maintenance .......................... 23

Engine Maintenance..........................................25

Adjust Valve Lash............................................25

Service Air Cleaner...........................................27

Service Spark Plugs..........................................28

Troubleshooting................................ 29

Generator Specifications.......................... 31

Engine Specifications ............................ 31

Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Not for Reproduction

4

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and

batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness.

A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the generator system unsafe.

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in

death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures,

nausea or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

WARNING Storage batteries give off explosive

hydrogen gas during recharging.Slightest spark

will ignite hydrogen and

cause explosion, resulting in

death, serious injury, and/or

property damage.Battery electrolyte fluid contains

acid and is extremely caustic.Contact with battery

contents will cause severe chemical burns.A battery

presents a risk of electrical shock and high short

circuit current.

• DO NOT dispose of battery in a fire. Recycle

battery.

• DO NOT allow any open flame, spark, heat, or

lit cigarette during and for several minutes after

charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber

boots and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product

and related accessories contain chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

Save These Instructions

Not for Reproduction

5

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result in

electrocution.Failure to isolate generator from utility

power could result in death or serious injury to electric

utility workers due to backfeed of electrical energy.

• When using generator for backup power, notify

utility company.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which

are worn, frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or

feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk

of a shock hazard.

• DO NOT allow unqualified persons or children to

operate or service generator.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical

power and contact the local authorities. Avoid

direct contact with the victim.

• Despite the safe design of the generator, operating

this equipment imprudently, neglecting its

maintenance or being careless can cause possible

injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• Before performing any maintenance on the

generator, disconnect the battery cable indicated

by a NEGATIVE, NEG or (-) first. When finished,

reconnect that cable last.

• After your system is installed, the generator may crank

and start without warning any time there is a power

failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are

extremely flammable and explosive,

which could cause burns, fire or

explosion resulting in death, serious

injury and/or property damage.

• DO NOT operate the equipment if the “fuel shut-off”

valve is missing or inoperative.

• Install the fuel supply system according to NFPA 37

and other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak

tested.

• After the generator is installed, you should inspect

the fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any

oil spills immediately. Ensure that no combustible

materials are left in the generator compartment. Keep

the area near the generator clean and free of debris.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate generator without protective

housings, covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything that

may be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel

and disconnect Negative (NEG or -) battery cable.

Not for Reproduction

6

NOTICE Improper treatment of generator can

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact

your authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation.

• The Oil Fill, Oil Drain and the Control Panel doors

must be installed whenever the unit is running.

• DO NOT expose generator to excessive moisture,

dust, dirt, or corrosive vapors.

• Despite the safe design of the generator, operating this

equipment imprudently, neglecting its maintenance or

being careless can cause possible injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as

a step. Stepping on the unit can cause stress and

break parts. This may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generator.

Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively:

-unit makes unusual noises.

CAUTION Installing the 15A fuse could cause

the engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed

from the control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring

has been completed and inspected.

CAUTION Excessively high operating speeds

could result in minor injury and/or equipment

damage.Excessively low speeds impose a heavy

load on generator.

• DO NOT tamper with governed speed. Generator

supplies correct rated frequency and voltage when

running at governed speed.

• DO NOT modify generator in any way.

WARNING

Exhaust heat/gases could ignite

combustibles or structures resulting in

death, serious injury and/or property

damage. Contact with muffler area could

cause burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5 m) minimum clearance from

any structure, shurbs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall opening,

shrubs or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must

have a minimum of 5 ft. (1.5 m) overhead clearance

from any structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect

provided fuel line to generator, DO NOT use with or

substitute any other flexible fuel line.

• Smoke detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Carbon monoxide

alarms cannot detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator

cooling and maintenance clearances.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any

forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester designed

for the exhaust system installed on this engine.

• Replacement parts must be the same and installed

in the same position as the original parts.

Not for Reproduction

7

Installation

We sincerely appreciate your patronage. For this

reason, we have made every effort to provide for a safe,

streamlined and cost-effective installation. Because

each installation is unique, it is impossible to know of

and advise the trade of all conceivable procedures and

methods by which installation might be achieved. Neither

could we know of possible hazards and/or the results of

each method or procedure. For these reasons,

Only current licensed electrical and plumbing

professionals should attempt home generator system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

Your home generator is supplied with this “Operator’s

Manual” and a separate “Installation Manual”. These

are important documents and should be retained by the

owner after the installation has been completed.

This product is only for use as an optional generator system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system

as defined by NFPA 70 (NEC).

• Emergency generator systems are intended

to automatically supply illumination, power,

or both, to designated areas and equipment

in the event of failure of the normal supply.

Emergency systems may also provide power for

such functions as ventilation where essential to

maintain life, where current interruption of the

normal supply would produce serious life safety

or health hazards.

• Legally Required standby generator systems

are intended to automatically supply power

to selected loads in the event of failure of the

normal source which could create hazards or

hamper rescue or fire-fighting operations.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

should attempt home generator system installations.

Installations must strictly comply with all applicable codes,

industry standards, laws and regulations.

For the Home Owner:

To help you make informed choices and communicate

effectively with your installation contractor(s), read and

understand Owner Orientation in this manual before

contracting or starting your generator installation.

To arrange for proper installation, contact the store at

which you purchased your generator, your dealer, a

licensed electrician or your utility power provider.

The generator warranty is VOID unless the

system is installed by licensed electrical and

plumbing professionals.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the U.S. Environmental Protection

Agency and by the California Air Resources Board (CARB).

For the Installing Dealer/Contractor:

For most applications, the installation manual contains

all the information required to properly install and

start the generator. This operator’s manual describes

routine operation and owner maintenance procedures.

If you need more information in this matter, please call

at 800-743-4115 between 8:00 AM and 5:00 PM CT.

Owner Orientation

This section provides generator owners with the

information necessary to achieve the most satisfactory

and cost effective installation possible.

The illustrations are for typical circumstances and

are meant to familiarize you with the installation

options available with your generator. A thorough

understanding of these options will provide

fundamental control over the cost of your installation,

as well as ensure your final satisfaction and security.

Federal and local codes, appearance, noise levels,

fuel types, and distances are the factors that must

be considered when negotiating with an installation

professional. Remember that as the distance from the

existing electrical service and gaseous fuel supply

increases, and the number of 90 degree bends in the

fuel supply increases, compensations in piping and

wiring materials must be made. This is necessary

to comply with local codes and overcome electrical

voltage drops and gaseous fuel pressure drops.

The factors mentioned above will have a direct affect

on the overall price of your generator installation.

In some areas you may need to acquire electrical

permits for installing the generator, building permits for

installing gas lines, and permits for noise allowances.

Your installer should check your local codes AND

obtain the permits before installing the system.

Not for Reproduction

8

Fuel Factors

An important consideration affecting the entire

installation is the type of fuel used by your generator.

The system was factory tested and adjusted using

either natural gas or liquid propane (LP vapor). For

proper engine function, factors that are inherent to

each of these fuels, your location and the duration

of possible utility interruptions are important

considerations in the following fuel guidelines:

• Use clean, dry fuel, free of moisture or any

particulate material. Using fuels outside the

following recommended values may cause

performance problems.

• In engines set up to run on propane (LP),

commercial grade HD5 propane with a minimum fuel

energy of 2500 BTUs/ft

3

with maximum propylene

content of 5% and butane and heavier gas content

of 2.5% and minimum propane content of 90%.

Natural gas rating will depend on specific fuel but typical

derates are between 10 to 20% off the LP gas rating.

Natural gas or LP engines are certified to operate on

natural or liquid propane gas. The emissions control

system for this engine is EM (Engine Modifications).

Power Decrease at High Altitude or High

Temperature

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power

will decrease 3.5% for each 1,000 feet (300 meters)

above sea level and 1% for each 10° F (5.6°C) above

77°F (25°C). Make sure you and your installer consider

these factors when determining total generator load.

WARNING Propane and Natural Gas are

extremely flammable and explosive,

which could cause burns, fire or

explosion resulting in death, serious

injury and/or property damage.

• The residential generator is equipped with an

automatic safety gas “fuel shut-off” valve.

• DO NOT operate the equipment if the “fuel shut-off”

valve is missing or inoperative.

Not for Reproduction

9

Generator Location

The actual physical location of your generator has a

direct affect on:

1. The amount of plumbing required to fuel

your generator.

2. The amount of wiring required to control and

connect your generator.

Specific location guidelines are discussed in the

installation manual. Acquaint yourself with that

information and confer with your installer. Be sure to

ask how your site might affect installation costs and

compliance with local codes and standards.

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas

could accumulate and enter inside or be drawn

into a potentially occupied building or structure.

• By law it is required in many states to have a

Carbon Monoxide (CO) detector in operating

condition in your home. Carbon monoxide

detector(s) (A) MUST be installed and maintained

indoors according to the manufacturer’s

instructions/recommendations. A CO monitor is an

electronic device that detects hazardous levels of

CO. When there is a buildup of CO, the monitor

will alert the occupants by flashing visual indicator

light and alarm. Smoke alarms cannot detect CO

gas.

• Ensure exhaust gas is kept away from any

windows, doors, ventilation intakes, soffit vents,

crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter

inside or be drawn into a potentially occupied

building or structure. Your neighbor’s home may

be exposed to the engine exhaust from your

standby generator and must be considered when

installing your standby generator.

• Wind and air currents should be taken into

consideration when positioning generator.

See the installation manual for full details on safe

generator location.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison

gas. Breathing carbon monoxide could result

in death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea or

fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

A

WARNING Exhaust heat/gases could ignite

combustibles or structures resulting in death,

serious injury and/or property damage.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5 m) minimum clearance from

any structure, shrubs, trees, or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall opening,

shrubs or vegetation over 12 in. (30.5 cm) in height.

• Standby generator weatherproof enclosure must

have a minimum of 5 ft. (1.5 m) overhead clearance

from any structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• USE ONLY flexible fuel line provided. Connect

provided fuel line to generator. DO NOT use with or

substitute any other flexible fuel line.

• Smoke detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Carbon monoxide

alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner

other than shown in illustrations.

Not for Reproduction

10

Delivery Inspection

Carefully inspect the generator for any damage that

may have occurred during shipment.

If loss or damage is noted at time of delivery, have

the person(s) making delivery note all damage

on the freight bill and affix his signature under the

consignor’s memo of loss or damage. If loss or

damage is noted after delivery, separate the damaged

materials and contact the carrier and your installer for

claim procedures. Missing or damaged parts are not

warranted.

The home generator system is supplied with:

• Oil (5W30 Synthetic)

• Flexible steel fuel line

• Installation and start-up manual

• Operator’s manual

• Spare access roof keys

• Spare 15 Amp ATO-type fuse

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 60” lengths of 3/4” nominal minimum

scheduled 40 steel pipe (NOT conduit)

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

Not for Reproduction

11

Controls

15kW, 16kW and 20kW Generator (Front View)

Read this Operator’s Manual and Important Safety Instructions before operating your generator.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

Generator is shown with roof and access covers

removed for clarity.

A - Lifting Holes — Provided at each corner for lifting

generator.

B - Alternator — An electrical machine that generates

an alternating current

C - Muffler — High-performance muffler lowers engine

noise to comply with most residential codes.

D - Circuit Breaker — Protects the system from shorts

and other over-current conditions.

E - Control Board — Used for generator operation

control, menu start-up, and informational display

functions.

F - Air Cleaner — Uses a dry type filter element to

protect engine by filtering dust and debris out of

intake air.

G - Engine Label — Identifies engine model and type

H - Spark Plug — A device in the cylinder head of the

engine that ignites the fuel mixture by means of an

electric spark.

J - Oil Filter — Filters engine oil to prolong generator

life.

K - Battery (installer supplied) — 12 Volt DC, lead

acid, automotive style battery provides power to

start the engine.

L - Oil Heater Port/ Oil Drain Hose Port — Provided

to allow an optional heating element to be installed.

Provided to facilitate oil changing.

M - Generator Data Label — Identifies generator

model number and serial number. Located inside

battery access compartment.

A

B

C

D

E

F

G

H

J

K

L

M

Not for Reproduction

12

15kW, 16kW and 20kW Generator (Back View)

Read this Operator’s Manual and Important Safety Instructions before operating your generator.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

Generator is shown with roof and access covers

removed for clarity.

A - Lifting Holes — Provided at each corner for lifting

generator.

B - Fuel Solenoid — Automatically opens and closes

to supply fuel to unit when needed.

C - Fuel Regulator — Controls fuel flow to engine for

proper operation.

D - Fuel Selector Valve — Used to select proper fuel

type (LP or NG).

E - Spark Plug — A device in the cylinder head of the

engine that ignites the fuel mixture by means of an

electric spark.

F - Oil Fill Cap — Location for adding oil to engine.

G - Electrical Field Wiring Inlet — Wires to and from

generator are centered in this location.

H - Air Cleaner — Uses a dry type filter element to

protect engine by filtering dust and debris out of

intake air.

J - Engine Oil Dipstick — Allows user to check engine

oil level easily.

K - Oil Heater Port — Provided to allow an optional

heating element to be installed to warm engine oil to

promote easy starting in cold climates.

A

B

C

D

E

F

G

H

J

K

Not for Reproduction

13

Access Panels

The generator is equipped with an enclosure that has

several access panels, as shown.

The access panels and the components located

behind them are listed below:

A - Roof (Control Panel, air filter, oil dipstick, and circuit

breaker)

B - Front Access Panel (oil drain and oil filter)

C - Battery Panel (battery and generator data label)

D - Rear Access Panel (fuel regulator, fuel selector, and

engine starter)

E - Control Panel Cover (field wiring and control wires)

Each generator is shipped with a set of identical keys.

These keys fit in the lock on the front removable panel.

The roof must be unlocked in order for it to open.

A

B

D

E

C

Not for Reproduction

14

To open roof:

1. Insert key into lock (A) of front panel. Gently push

down on roof above the lock to aid in turning the

key. Turn key one quarter turn clockwise.

2. Lift roof to the open position.

To remove front panel:

1. Remove the two bolts (B) that secure the panel to the

unit.

2. Lift panel to remove from unit.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

To remove rear panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts (C) that secure the panel to

the unit.

3. Lift panel to remove from unit.

To secure rear panel:

1. Slide panel into place on unit.

2. Secure the panel with two bolts.

To remove battery panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts (D) that secure the panel to

the unit.

3. Lift up on panel and remove.

To secure battery panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

A

B

C

D

Not for Reproduction

15

System Control Panel

Compare this control panel illustration with your generator to familiarize yourself with the location of these important controls:

A - Menu/Programming Navigation Buttons — See

Menu section for details

B - Mini USB Port — Authorized Dealer Service Use

Only

C - Generator Operation Control Buttons —

•“AUTO” Normal operating position. Press and

hold button to put unit into Automatic mode. If

an utility power outage is sensed, the system

will start the generator. When utility power is

restored, auto lets the engine stabilize internal

temperatures, shuts o the generator, and waits

for the next utility outage.

•“OFF” Turns o running generator, prevents unit

from starting, and resets any detected service

codes.

OFF must be pressed and held for more than 5

seconds in order to reset service codes.

•“MANUAL” Used to manually start the generator.

“AUTO” LED — LED will light when unit is placed

into Auto mode. LED will blink if exercise cycle is

not set or set to OFF.

D – 15 Amp Fuse — Protects the home generator

DC control circuits. If the fuse has ‘blown’ (melted

open) or was removed, the engine cannot crank

or start. Replace the fuse using only an identical

ATO 15A fuse. One spare fuse is supplied with

the unit.

E - Cover — This protective cover must be opened to

access the fuse and the USB port.

F - Digital Display — Displays generator mode,

menu options, service codes, and service engine

indicators

MENU

ESC

AUTO OFF

MANUAL

A

B

C

F

E

D

Not for Reproduction

16

Menu

MENU

ENTER THE MENU (VIEW SETTINGS)

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT) RETURN TO LAST MENU ITEM

RIGHT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

LEFT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

MANUAL MODE

USED TO MANUALLY START THE GENERATOR. PRESS AND

HOLD BUTTON TO START THE GENERATOR.

OFF

TURNS OFF RUNNING GENERATOR, PREVENTS UNIT FROM

STARTING, AND RESETS ANY DETECTED Service codeS.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO

PUT UNIT INTO AUTOMATIC MODE. IF A UTILITY POWER OUTAGE

IS SENSED, THE SYSTEM WILL START THE GENERATOR.

WHEN UTILITY POWER IS RESTORED, AUTO LETS THE ENGINE

STABILIZE INTERNAL TEMPERATURES, SHUTS OFF THE

GENERATOR, AND WAITS FOR THE NEXT UTILITY POWER

OUTAGE.

GENERAL

SET-UP

PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT]

FOR THREE SECONDS TO ENTER THE PROGRAM

MODE.

ADVANCED

SETTINGS

PRESS AND HOLD [ARROW LEFT, ARROW RIGHT AND

ESC] FOR THREE SECONDS TO ENTER THE ADVANCED

SETTINGS MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE

SECONDS TO ENTER THE WIRELESS LINKING MODE.

The following chart shows the icons for the buttons that control the system control panel:

The following chart describes key sequences for accessing different programming modes:

Not for Reproduction

17

General Set Up Screen

For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as

outlined below.

NOTE Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle

was also set at the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard

Time. To update or change these settings, follow the steps below.

IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 30 SECONDS,

THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.

SET DATE

If set to OFF, display will read:

EXERCISE CYCLE OFF

or

YEAR

FLASHING

MONTH

FLASHING

DAY##

FLASHING

SET TIME

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

or or or

or

or or or

or

or or or or

DAY OF WEEK

FLASHING

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

SET EXERCISE CYCLE

EVENT LOG

Display will scroll last service code event, date, time,

and ambient temperature of when the event occurred.

or

Not for Reproduction

18

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

• GENERATOR READY - if the unit is in standby

and utility power is present.

• GENERATOR ON - if the unit is running and utility

power is not present.

• SERVICE CODE - if a system service code has

been detected.

General System Parameters

To view general system parameters, press the MENU

button.

The following will scroll across the digital display and

then move to the next item:

• Run time

• Date

• Time

• Exercise Cycle date and start time

The user can press the LEFT ARROW or RIGHT

ARROW at any time to move to the next item.

The user can press ESCAPE to go back to

GENERATOR READY.

If no user inputs are made for 10 seconds after all the

items have been displayed, the control board will reset

to

GENERATOR READY.

AUTOMATIC MODE

GENERATOR READY OR SERVICE CODE

DESCRIPTION

(When Generator NOT Running - Auto Mode)

GENERATOR ON

(When Generator Running - Auto Mode)

(MENU)

RUN TIME

or

TIME

DATE

EXERCISE CYCLE

Not for Reproduction

19

Operation

Important Owner’s Considerations

Engine Oil

The engine is shipped from the factory pre-run and

filled with synthetic oil (API SJ/CF 5W-30). This allows

for system operation in a wide range of temperature

and climate conditions. Before starting the engine,

check oil level and ensure that engine is serviced as

described in Maintenance.

Battery

The installer must supply rechargeable 12 volt DC

starting battery. See Battery in Final Installation

Considerations in the installation manual.

With the battery installed, all wiring to transfer switch

and generator completed, utility power supplied to the

automatic transfer switch, and the unit in AUTO mode,

the battery receives a trickle charge while the engine

is not running. The trickle charge cannot be used to

recharge a battery that is

completely discharged.

15 Amp Fuse

The generator’s 15 Amp fuse is critical to correct

system operation. The 15 Amp fuse was removed

at the factory to prevent the unit from starting during

shipping. Your installer will ensure the fuse is properly

installed upon completion of the installation.

Automatic Operation Sequence

The generator’s control board constantly monitors

utility voltage. Should utility voltage drop below a

preset level, the control board will signal the engine to

crank and start.

When utility voltage is restored above a preset voltage

level, the engine is signaled to shut down.

The actual system operation is not adjustable and

is sequenced by sensors and timers on the control

board, as follows:

Utility Voltage Dropout Sensor

• This sensor monitors utility source voltage.

• If utility source voltage drops below about

70 percent of the nominal supply voltage, the

sensor energizes a 3 second timer. The timer is

used to ‘sense’ brown-outs.

• Once the timer has expired, the engine will crank

and start.

Utility Voltage Pickup Sensor

This sensor monitors utility power voltage. When utility

voltage is restored above 80 percent of the nominal

source voltage, a time delay starts timing and the

engine will go to engine cool-down.

Engine Cool-down Timer

When utility power is sensed and the load transfers to

the utility source, the engine will go into a cool down

period as described below:

• If the generator has run for MORE than 5 minutes,

once the utility transfer occurs, the engine will

continue to run for about 1 minute before shutting

down.

• If the generator has run for LESS than 5 minutes,

once the utility transfer occurs, the engine will

continue to run until 5 minutes has elapsed before

shutting down.

CAUTION With the system switch set to AUTO,

the engine could crank and start at any

time without warning, resulting in minor or

moderate injury.

• To prevent possible injury that may be caused by

such sudden starts, always set the system switch to

OFF if performing maintenance on the system.

• Remove the 15 Amp fuse before working on or

around the generator or transfer switch.

NOTICE Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil will result in equipment failure.

• DO NOT attempt to crank or start the engine before

it has been properly serviced with the recommended

oil. This may result in an engine failure.

• Damage to equipment resulting from failure to follow

this instruction will void generator warranty.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds,

chemicals known to the State of California to

cause cancer and reproductive harm. Wash hands

after handling.

Not for Reproduction

20

Setting Exercise Timer

The generator is equipped with an exercise timer.

During the exercise period, the unit runs for

approximately 20 minutes and then shuts down.

Electrical load transfer DOES NOT occur during the

exercise cycle (unless an utility power outage occurs).

The generator will only enter the exercise cycle if the

unit is in the AUTO mode and this exact procedure is

followed.

To set the exercise timer:

NOTICE The generator is set with a service code

exercise cycle setting of Tuesday at 2:00 P.M, Central

Time. To change the cycle setting, proceed to the

following steps:

1. Choose the day and time you want your generator

to exercise.

2. Press and hold the left arrow and right arrow

simultaneously for 3 seconds to enter the General

Set-Up program mode. See General Set-Up flow

chart in Menu Section.

3. Verify and/or set the time and date on the unit.

4. Go to the SET EXERCISE prompt and hit the “OK”

button.

NOTICE Items will flash until they are selected.

SELECT DAY: Use the left or right arrow to toggle

through the days of the week, Once the day is

selected, hit the “OK” button.

SELECT HOUR: Use the left or right arrow to

toggle through between 1 and 12. Choose the

hour of day you want the generator to exercise

then hit the “OK” button.

SELECT MINUTE: Use the left of right arrow to

toggle between :00 and :59. Choose the minute of

the day you want the generator to exercise then

hit the “OK” button.

SELECT AM/PM: Use the left of right arrow to

toggle between AM and PM. Once chosen, hit the

“OK” button.

NOTICE During the weekly exercise cycle, the

generator will run for 20 minutes, but it will not

supply power to the home. During the exercise

cycle, the in-home monitor will continue blinking the

GENERATOR READY green LED.

If you want to change the day and time the unit

exercises, simply perform the procedure again.

To turn off the generator exercise cycle, go to the OFF

selection within the day of the week menu and press

OK. The

display will then scroll: EXERCISE CYCLE

OFF.

Maintenance

Servicing the System

Before performing any generator maintenance, always

perform the following steps:

1. Set generator’s circuit breaker to its OFF position.

2. Press and hold the control board OFF button.

3. Remove 15 Amp fuse from control board.

4. Utility voltage is present at generator control

board. Disconnect power before servicing control

board by removing the fuses from the transfer

switch.

5. After all servicing has been completed, replace

fuses in transfer switch, replace 15 Amp fuse in

control board, set circuit breaker ON and press

and hold control board AUTO button.

Service Code Detection System

The generator may have to run for long periods of time

with no operator present. For that reason, the system

is equipped with sensors that automatically shut down

the generator in the event of potentially damaging

conditions, such as low oil pressure, high temperature,

over speed, and other conditions.

The generator’s control board shows service code

descriptions scrolling across the digital display. The

service code descriptions are listed below:

• Low Battery Voltage

• Low Oil Pressure

• Under Voltage

• Over Voltage

• Engine Does Not Start

• Low Frequency

• Engine Overspeed

• High Oil Temperature

• Transfer Switch Service code

• Battery Charge Circuit

Page is loading ...

Simplicity 040394-00 User manual

Simplicity 040394-00 User manual

in other languages

Other documents