Ibiza Light LED6-QUAD Owner's manual

Page is loading ...

Manual - LED6-QUAD

2

©Copyright LOTRONIC 2020

‘SPIDER’ LIGHT EFFECT

INSTRUCTION MANUAL

CONTENTS OF THE CARTON:

• 1 x ‘SPIDER’ LIGHT EFFECT

• 1x Mains lead

• 1x User Manual

UNPACKING INSTRUCTIONS

Immediately upon receiving a xture, carefully unpack the carton, check the contents to ensure that all parts are

present and have been received in good condition. Notify the freight company immediately and retain packing

material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mis

-

handling. Keep the carton and all packing materials. In the event that a xture must be returned to the factory, it

is important that the xture be returned in the original factory box and packing.

EXPLANATION OF SYMBOLS

The triangle containing a lightning symbol is used to indicate whenever your health is at risk (due to electro-

cution, for example).

An exclamation mark in a triangle indicates particular risks in handling or operating the appliance.

The unit complies with CE standards

For indoor use only

Protection class I. Requires an earth connection

0.5m

Minimum distance between the appliance and other objects

Don’t stare into the light beam

CAUTION

DO NOT OPEN THE HOUSING

SHOCK HAZARD

IMPORTANT SAFETY INSTRUCTIONS AND DANGER WARNINGS

• Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also

receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting

to is not higher than that stated on the decal or rear panel of the xture.

• This product is intended for indoor use only!

• It is essential that the device is earthed. A qualied person must carry out the electric connection.

• To prevent risk of re or shock, do not expose xture to rain or moisture. Make sure there are no ammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces.

Be sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse

size and type.

• Secure xture to fastening device using a safety chain. Never carry the xture solely by its head. Use its carry-

ing handles.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the xture at temperatures higher than

this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the near

-

Manual - LED6-QUAD

3

www.ibiza-light.com

EN

est authorized technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

• The product is for decorative purposes only and not suitable as a household room illumination.

• The light source of this luminaire is not replaceable. When it reaches the end of its life time, the whole unit

must be discarded.

• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

FEATURES

Dynamic, reactive light eect featuring 2 rows of 3x 10W RGBW 4-in-1 LED projectors each.

• 10x / 14x DMX channels

• 6x 10W long-life RGBW 4-in-1 LEDs (>50.000 h)

• Auto, DMX and music-controlled modes

• Built-in programs

• Strobe eect

• Electronic dimmer 0-100%

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is rmly xed to

avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit

is secure and able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can

hold 12 times the weight of the unit when installing the xture.

The equipment must be xed by professionals at a place where is out of the reach of people and where nobody

can pass by or under it.

FUSE REPLACEMENT

Disconnect the power cord before replacing a fuse and always replace with the same type fuse

• With a at head screwdriver wedge the fuse holder out of its housing.

• Remove the damaged fuse from its holder and replace with exactly the same type of fuse.

• Insert the fuse holder back in its place and reconnect power.

• The fuse is located inside this compartment. Remove using a at head screwdriver.

FIXTURE LINKING

You will need a serial data link to run light shows of one or more xtures using a DMX-512 controller or to run

synchronized shows on two or more xtures set to a master/slave operating mode. The combined number of

channels required by all xtures on a serial data link determines the number of xtures that the data link can

support.

Console Light1 Light2 Light3

Important: Fixtures on a serial/data link must be daisy chained in one single line. Maximum recommended seri-

al data link distance: 100 meters. Maximum recommended number of xtures on a serial data link: 32 xtures

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

DMX CONNECTOR CONFIGURATION

INPUT

COMMON

DMX +

DMX-

Resistance 120 ohm

1/ 4w between pin 2

(DMX-) and pin 3

(DMX+) of the last

fixture.

Termination reduces signal errors. To avoid signal

transmission problems and interference, it is always

advisable to connect a DMX signal terminator.

Manual - LED6-QUAD

4

©Copyright LOTRONIC 2020

CAUTION

Do not allow contact between the common and the xture’s chassis ground. Grounding the common can cause

a ground loop, and your xture may perform erratically. Test cables with an ohm meter to check correct polarity

and to make sure the pins are not grounded or shorted to the shield or each other.

SETTING UP A DMX SERIAL DATA LINK

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the con

-

troller.

2. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector to the

input connector of the next xture consisting of a (male) 3 pin connector.

3. Then, proceed to connect from the output as stated above to the input of the following xture and so on.

MASTER/SLAVE FIXTURE LINKING

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the rst

xture.

2. Connect the end of the cable coming from the rst xture which will have a (female) 3 pin connector to the

input connector of the next xture consisting of a (male) 3 pin connector. Then, proceed to connect from the

output as stated above to the input of the following xture and so on

Often, the set up for Master-Slave and Stand-alone operation requires that the rst xture in the chain be initial

-

ized for this purpose via either settings in the control panel or DIP-switches. Secondarily, the xtures that follow

may also require a slave setting. Please consult the '' Operating Instructions» section in this manual for complete

instructions for this type of setup and conguration.

OPERATING INSTRUCTIONS

NAVIGATION THROUGH THE CONTROL PANEL

Access control panel functions using the four panel buttons located directly underneath the LCD Display..

Button Function

MENU Used to access the menu or to return to a previous menu option

UP Scrolls through menu options in ascending order

DOWN Scrolls through menu options in descending order

ENTER Used to select and store the current menu or option within a menu

To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach function you

wish to change. When you reach the function you wish to change, press the ENTER button. When a function

is selected, use the UP or DOWN buttons to change the function settings. Once your changes are made, press

the ENTER button, and then press and hold the MENU button for at least three seconds to conrm and lock the

change into the system memory. To exit without making any adjustments, press the MENU BUTTON. The display

will lock after 30 secondes. Press the MENU button for 3 seconds to unlock.

MENU MAP

ADDR A001---A512 (DMX ADDRESS)

CHND 10CH, 14CH (DMX CHANNEL OPTION)

SLND MAST, SL 1, SL 2 ( MASTER, SLAVE OPTION)

SHND Sh O - Sh15: Show mode

Auto OFF/ON: Auto Mode

SOUN ON /OFF (SOUND CONTROL)

SENS Sound sensitivity control (0 close, 100 The most sensitive)

PINT YES, NO (Tilt 1 positive direction or reverse direction)

TINT YES , NO (Tilt 2 positive direction or reverse direction)

LED ON, OFF (Background LIGHT ON/OFF)

DISP YES, NO (Reverse Display)

TEST Auto test

RSET YES, NO Restore factory settings

UP

DOWN

MENU ENTER

8.8.8.8.

Manual - LED6-QUAD

5

www.ibiza-light.com

EN

SETTINGS

DMX ADDRESS SETTING

1. Press the MENU, UP or DOWN button until “ADDR” is displayed, press ENTER.

2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired

address. Press ENTER to confirm.

DMX CHANNEL MODE

1. Press the MENU button until “CHND” is displayed, press ENTER. Either “10CH”, “14CH” will be displayed

2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confirm and exit.

SLND – SLAVE MODE

To select Slnd, press the ENTER button to show the SLAVE MODE on the display. Use the DOWN/UP button to

select Mast (MASTER),Sl1 (SLAVE 1), Sl2 (SLAVE 2) modes. Once the mode has been selected, press the ENTER

button to conrm.

NOTE: In a Master/Slave conguration you can set one xture to Master and then set the next xture to “SL 2”, the xtures will now have

opposite movements to each other.

SHOW MODES 0-15 (FACTORY PROGRAMS).

Show mode can run with or without sound active mode active.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between 0-15. Programs 1-15 are factory programs,

while “Sh 0” is random mode. Press the UP or DOWN buttons to find your desired show.

3. When you have found your desired show press ENTER, then press and hold the MENU button for at least

3 seconds to activate. After you have set your desired show, it can be changed at any time using the UP or

DOWN buttons.

AUTO PROGRAM

1. Press the MENU button until “AUTO” is displayed, press ENTER.

2. The Display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” or “OFF”.

SOUND ACTIVE MODE

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to activate sound

active mode, or “OFF” to deactivate sound active mode.

3. Press ENTER, then press and hold the MENU button for at least 3 seconds to activate.

SOUND SENSITIVITY

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0

being the least sensitive and 100 being the most sensitive.

3. When you have found your desired setting press ENTER to confirm.

TILT1 INVERSION

1. Press the MENU button until “PINT” is displayed, press ENTER. Either “YES” or “NO” will be displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons until YES is displayed, press ENTER to confirm.

3. To deactivate Tilt inversion, select NO and press Enter.

TILT2 INVERSION

1. Press the MENU button until “TINT” is displayed, press ENTER. Either “YES” or “NO” will be displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons until YES is displayed, press ENTER to confirm.

3. To deactivate Tilt inversion, select NO and press Enter.

DISPLAY BACK LIGHT

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED

display on at all times, or “OFF” to switch to have the LED display switch off after 10 seconds.

Manual - LED6-QUAD

6

©Copyright LOTRONIC 2020

3. Press ENTER and then press and hold the MENU button for at least three seconds to confirm.

DISPLAY REVERSE 180°

1. Press the either the MENU button until “DISP” is displayed, press ENTER.

2. Press the UP button to select “DSIP” to reverse the display, or “DISP” to change the display back.

3. Press ENTER to confirm.

SELF TEST PROGRAM

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The fixture will now run a self test. Press MENU to exit.

RESET

Press the MENU button until “Reset” is displayed. Press the ENTER button and the unit will reset itself.

DMX CHANNEL TABLE: SEE AT THE END OF THE MANUAL

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize

light output. Cleaning frequency depends on the environment in which the xture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

• Clean with soft cloth using normal glass cleaning uid.

• Always dry the parts carefully.

• Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

SPECIFICATIONS

Power supply ....................................................................................................................100-240V~ 50/60Hz

Consumption .............................................................................................................................................75W

LED source .....................................................................................................................6 x 10W RGBW 4-in-1

DMX channels .........................................................................................................................................10/14

Electronic dimming ............................................................................................................................0 - 100%

Tilt ............................................................................................................................................................. 90°

Beam angle .................................................................................................................................................. 4°

Dimensions ......................................................................................................................225 x 145 x 150mm

Weight ...................................................................................................................................................2.25kg

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your

dealer about the way to proceed.

Page is loading ...

Manual - LED6-QUAD

30

DMX CHANNEL TABLES

10-CHANNEL TABLE

Channel DMX Value Function Fonctions

1 0---255 Tilt 1 Tilt 1

2 0---255 Tilt 2 Tilt 2

3 0---255 Tilt 1, Tilt 2 speed Tilt 1, Tilt 2 vitesse

4 0---255 Dimmer from 0-100% Dimmer 0-100%

5

Strobe Stroboscope

000-007 O Fermer le stroboscope

008-015 On Ouvrir le stroboscope

016-131 Strobe from slow to fast Stroboscope lent -> rapide

132-139 On Ouvrir le stroboscope

140-181 Strobe Fast open slow close Ouverture rapide, fermeture lente

182-189 On Ouvrir le stroboscope

190-231 Strobe Slow open fast close Ouverture lente, fermeture rapide

232-239 On Ouvrir le stroboscope

240-247 Random strobe Aléatoire

248-255 On Ouvrir le stroboscope

6 0---255 Red Dimming Variateur rouge

7 0---255 Green Dimming Variateur vert

8 0---255 Blue Dimming Variateur bleu

9

0---255 White Dimming Variateur blanc

10

Special Functions Fonctions spéciales

000-007 Only others channels can be controlled Seuls les autres canaux sont pilotables

008-063 Auto run Fonctionnement automatique

064-127 Sound active Activation audio

128-255 Reset Reset

Manual - LED6-QUAD

31

www.ibiza-light.com

EN

14-CHANNEL TABLE

Channel DMX Value Function Fonction

1 0---255 Tilt 1 Tilt 1

2 0---255 Tilt 2 Tilt 2

3 0---255 Tilt 1, Tilt 2 speed Tilt 1, Tilt 2 vitesse

4 0---255 Dimmer from 0-100% Dimmer 0-100%

5

Strobe Stroboscope

000-007 O Fermer le stroboscope

008-015 On Ouvrir le stroboscope

016-131 Strobe from slow to fast Stroboscope lent -> rapide

132-139 On Ouvrir le stroboscope

140-181 Strobe Fast open slow close Ouverture rapide, fermeture lente

182-189 On Ouvrir le stroboscope

190-231 Strobe Slow open fast close Ouverture lente, fermeture rapide

232-239 On Ouvrir le stroboscope

240-247 Random strobe Aléatoire

248-255 On Ouvrir le stroboscope

6 0---255 Red 1 Dimming Variateur rouge 1

7 0---255 Green 1 Dimming Variateur vert 1

8 0---255 Blue1 Dimming Variateur bleu 1

9 0---255 White1 Dimming Variateur blanc 1

10 0---255 Red 2 Dimming Variateur rouge 2

11 0---255 Green 2 Dimming Variateur vert 2

12 0---255 Blue 2 Dimming Variateur bleu 2

13 0---255 White 2 Dimming Variateur blanc 2

14

Special Function Fonctions spéciales

000-007 Only others channels can be controlled Seuls les autres canaux sont pilotables

008-063 Auto run Fonctionnement automatique

064-127 Sound active Activation audio

128-255 Reset Reset

www.ibiza-light.com

Assembled in PRC for LOTRONIC S.A.

Avenue Zénobe Gramme 9

B-1480 Saintes

View the item on our website

Any questions? Please contact us on facebook

Ibiza Light LED6-QUAD Owner's manual

Ibiza Light LED6-QUAD Owner's manual

in other languages

Related papers

Other documents