Grand Hall 6306LP Owner's manual

Brand: Grand Hall

Model: 6306LP

Category: Barbecues & grills

Type: Owner's manual

NOTE TO ASSEMBLER / INSTALLER:

Leave this manual with the consumer.

NOTE TO CONSUMER:

Keep this manual for future reference.

RECORD YOUR SERIAL # __________________

(see silver CSA label on main body of grill)

IMPORTANT:

Grill Information Center:

Call us first if you have any problem with this

product. We can help you with questions about

assembly and grill operation or if there are

damaged or missing parts when you unpack

this unit from the shipping box. Please call

before returning to the store.

1-877-934-7455

8am-4:30pm CST, Monday through Friday

Failure to comply with these instructions could

result in a fire or explosion that could cause

serious bodily injury, death or property damage.

Whether this grill was assembled by you or

someone else, you must read this entire manual

before using your grill to ensure the grill is

properly assembled, installed and maintained.

Use your grill at least 3 feet away from any

wall or surface. Use your grill at least 3 feet

away from combustible objects that can melt or

catch fire (such as vinyl or wood siding, fences

and overhangs) or sources of ignition including

pilot lights on water heaters and live electrical

appliances.

THIS GAS APPLIANCE IS DESIGNED FOR

OUTDOOR USE ONLY.

Combustion byproducts produced when using

this product contain chemicals known to the

State of California to cause cancer, birth de-

fects, or other reproductive harm.

WARNING

! !

OPERATOR'S MANUAL

Liquid Propane Gas (LPG)

Grill

Model 6306LP

Natural Gas (NG) Grill

Model 6306NG

Manual # P80157005A - Date:2006/02/27

The Grease Draining Tray and Grease

Receptacle must be visually inspected

before each grill use. Remove any grease

and wash Grease Draining Tray and

Grease Receptacle with a mild soap and

warm water solution. Failure to comply

with these instructions could result in

a grease fire or explosion that could

cause serious bodily injury, death or

property damage.

WARNING

! !

WARNING

! !

Do not store spare LP cylinder

within 10 feet (3m) of this appliance.

Do not store or use gasoline or

other flammable liquids and

vapors within 25 feet (8m) of this

appliance.

When cooking with oil/grease, do

not allow the oil/grease to get

hotter 350°F (177°C).

Do not leave oil/grease unattended.4.

Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appli-

ances.

An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

WARNING

! !

Grill Installation Codes

The installation must conform with local codes or, in

the absence of local codes, with either the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-

B149.1, Natural Gas and Propane Installation Code.

LPG grill models must be used with

Liquid Propane Gas and the regulator

assembly supplied. Natural Gas models

must be used with Natural Gas only. Any

attempt to convert the grill from one fuel

type to another is extremely hazardous

and will void the warranty.

Never use your gas grill in a garage, porch,

shed, breezeway or any other enclosed area.

Never obstruct the flow of ventilation air

around your gas grill housing.

Never disconnect the gas regulator or any gas

fitting while your grill is lit. A lit grill can ignite

leaking gas and cause a fire or explosion which

could result in property damage, personal in-

jury or death.

Keep gas regulator hose away from hot

grill surfaces and dripping grease. Avoid

unnecessary twisting of hose. Visually in-

spect hose prior to each use for cuts, cracks,

excessive wear or other damage. If the hose

appears damaged do not use the gas grill.

Call:1-877-934-7455 for an authorized replace-

ment hose.

•

WARNING

•

If you smell gas:

Shut off gas to the appliance.

Extinguish any open flame.

Open lid.

If odor continues, keep away from

the appliance and immediately call

your gas supplier or your fire

department.

DANGER

! !

Leaking gas may cause a fire or

explosion which could result in property

damage, personal injury or death.

Table of Contents

Primary Safety Warnings.....................................1-3

Pre-Assembly Instructions.......................................3

Part Diagrams and Lists...................................4-9

Assembly Instructions..........................................10-16

Rotisserie Assembly Instruction......................17-18

Use & Care Instructions:

• Gas Safety and Leak Tests....................19-22

• Lighting Instructions.....................................23-24

• Troubleshooting...................................................24

• Cleaning and Maintenance........................25-26

• Cooking Guide..............................................A1-A4

• Frequently Asked Questions.....................A5-A6

Warranty Terms........................................Back Cover

Pre-Assembly Instructions For Your Safety

Tools Required for Assembly include:

protective work gloves

protective eyewear

While it is possible for one person to unpack this gas

grill, obtain assistance from another person when

handling the large pieces.

Use the Hardware and Part Diagrams to ensure all

items are included and free of damage.

Do not assemble or operate the grill if it appears

damaged. If there are damaged or missing parts

when you unpack the shipping box or you have

questions during the assembly process, call the:

To expedite the assembly process follow these

general guidelines:

•

Grill Information Center 1-877-934-7455

8am-4:30pm CST, Monday through Friday

Phillips Head Screwdriver

•

Spiders and small insects can spin webs and

nest in the grill Burner Tubes during transit and

warehousing which can lead to a gas flow

obstruction resulting in a fire in and around the

Burner Tubes. This type of "FLASHBACK FIRE"

can cause serious grill damage and create an

unsafe operating condition for the user.

To reduce the chance of FLASHBACK

FIRE you must clean the Burner Tubes

as follows before initial use.

Also do this at least once a month in summer

and fall or whenever spiders are active in your

area, and if your grill has not been used for an

extended period of time.

CAUTION

! !

Failure to comply with these instructions may

result in a hazardous situation which, if not

avoided, may result in injury.

METHOD 1: Bend a stiff wire or wire coat

hanger into a small hook as shown and run

the hook through the Burner Tube and inside

the Burner several times to remove debris.

TO CLEAN BURNER TUBE, INSERT HOOK

HERE

METHOD 2: Use a bottle brush with a flexible

handle and run the brush through the Burner

Tube and inside the Burner several times to

remove any debris.

METHOD 3: Use an air hose to force air

through each Burner Tube. The forced air

should pass debris or obstructions through

the Burner and out the Ports.

Burner

Foot

WARNING

! !

For safe operation ensure the Gas Valve Assem-

bly Orifice is inside the Burner Tube before using

your grill. See figure. If the Orifice is not inside

the Burner Tube, lighting the Burner may cause

explosion and/or fire resulting in serious bodily

injury and/or property damage.

Orifice Burner Tube

Gas Valve Assembly

Remove the screws from the rear of each Main

Burner using a Phillips Head Screwdriver.

Carefully lift each Burner up and away from the

Gas Valve Orifice.

Check and clean Burner/Venturi Tubes for insects

and insect nests. A clogged tube can lead to a fire

beneath the grill.

Refer to the figure below and perform one of

these 3 cleaning methods:

PART#PART DESCRIPTIONQTYPURPOSE OF PART

P06020005AHardware Pack 1For use in assembly (For LPG & NG model)

S112G04081Phillips Head Screw 1/4"x1/2"8

S142G03061

Countersink Flat Head Screw

3/16"x3/8"

S112G04081Phillips Head Screw 1/4"x1/2" 16Install Cart Bottom Shelf and Casters

S112G03061Phillips Head Screw 3/16"x3/8" 4

S313G03061Flange Nut 3/16" 6

S142G03061

Countersink Flat Head Screw

3/16"x3/8"

S112G03041Phillips Head Screw 3/16"x1/4" 4

P00201001CDoor Handle2

S112G03061Phillips Head Screw 3/16"x3/8" 4

S313G03061Flange Nut 3/16" 4

S112G03061Phillips Head Screw 3/16"x3/8" 4

S172M04101Self Tapping Screw M4x10mm 1

S112G04191Phillips Head Screw 1/4"x1-3/16" 4

S313G03061Flange Nut 3/16" 4

P05507031ELighting Stick1

S112G04081Phillips Head Screw 1/4"x1/2" 8Install Side Shelf Brackets

S112G04081Phillips Head Screw 1/4"x1/2" 8

S313G04081Flange Nut 1/4" 8

S313G04081Flange Nut 1/4" 2Install Tool Holder and Tool Hooks

S112G03061Phillips Head Screw 3/16"x3/8" 2

S313G03061Flange Nut 3/16" 2

P05536001PHose Holder 1

S112G03061Phillips Head Screw 3/16"x3/8" 2

S313G03061Flange Nut 3/16" 2

P05536001PHose Holder 1

S233G05461Wing Bolt 5/16"x4-1/2"1Secures Gas Tank

Already installed in Tank Hole of Cart Bottom Shelf

Install Regulator Assembly (For LPG Model only)

Install Side Shelf and Side Burner Frame

Attaches NG Regulator Assembly to Right Cart

Panel (For NG model only)

Install Caster Seats

Install Right and Left Door

Install Door Bracket, Grill Bowl and Lighting Stick

Install Cart Rear Panel, Door Stop Plate and Door

Handles

Hardware Pack Parts List for Models 6306LP & 6306NG

Phillips Head Screw

1/4" x 1/2"

Qty. 40

Part # S112G04081

Lighting Stick

Qty. 1

Part # P05507031E

Scale 1:2

Phillips Head Screw

3/16" x 1/4"

Qty. 4

Part # S112G03041

Flange Nut 3/16"

Qty. 16

Part # S313G03061

Phillips Head Screw

1/4" x 1-3/16"

Qty. 4

Part # S112G04191

Self Tapping Screw

M4 x 10mm

Qty. 1

Part # S172M04101

Countersink Flat Head Screw

3/16" x3 /8"

Qty. 10

Part # S142G03061

Flange Nut 1/4"

Qty. 10

Part # S313G04081

Phillips Head Screw

3/16" x 3/8"

Qty. 14

Part # S112G03061

* Two Batteries/AA included in the Hardware Pack.

Door Handle

Qty. 2

Part # P00201001C

Hardware Pack for Models 6306LP & 6306NG

Hardware already installed in Tank Hole of Cart

Bottom Shelf

Wing Bolt 5/16"x4-1/2"

Qty. 1 (LPG model)

Part # S233G05461

Scale 1:2

Hose Holder

Qty. 1

Part # P05536001P

Scale 1:2

(NG Only)

Parts Diagram for Models 6306LP & 6306NG

KEYDESCRIPTIONPART # QTY

1LidP0011920MA

Temperature GaugeP00601061A1

Lid HandleP00205068B1

Protective PadP05518011I4

Cooking Rack/Secondary

P01517004B

6ACooking GridP01604030A2

6BCooking GridP01604029A1

7Burner/MainP02008024A6

8Smoker BoxY04600021

9Savor Plates®P01708033B5

10Savor Plates® Bracket, FrontP03328015A6

11Savor Plates® Bracket, RearP03328017A6

12Burner BracketP02211184A1

13Grease Tray Heat Shield,UpperP06904045C1

14Side Shelf, LeftP01106005A1

15Side Shelf Bracket,Left Front/Right RearP01206005F2

16Side Shelf Bracket,Left Rear/Right FrontP01106005F2

17Bowl Panel, LeftP0072067PC1

18Bowl Panel, RightP0072167PC1

19Grease Draining PlateP06902008C2

20Bowl Wind ShieldP06906039C2

21Lid HingeP05501020A2

22Back Burner Wind ShieldP06905037B1

23Back Burner AssemblyY03100251

24Back Burner ElectrodeP02610005B1

Back Burner Orifice(LPG)P06531012A1

Back Burner Orifice(NG)P06531013A1

26Back Burner Extension TubeP03717039B1

27Bowl Panel, RearP0072567BC1

28Bowl Panel, FrontP0073863BC1

29Gas Collector Box with ElectrodeP02609007B6

30Electric Wire SetP02615089A1

31Grease Tray Heat Shield,LowerP06903047B1

Gas Valve/Manifold Assembly(LPG)Y00603531

Gas Valve/Manifold Assembly(NG)Y00603541

33Name PlateP00417005G1

34Control Panel, UpperP02910698S1

Control Panel, Extension(LPG)P02910771A1

Control Panel, Extension(NG)P02910761F1

36Control Panel, LowerP02910751A1

37Control Knob SeatP03415014S7

38Control Knob SpringP05504021A8

39Control Knob for Main Burners P03411383S6

40Control Knob for Back BurnerP03411373S1

41Electric Ignitor, 6-portP02502145C1

42Electric Ignitor, 2- portP02502192C1

43Tool HolderP05209004B1

44Tool HooksP05514131F3

45Side Burner LidP01127004B1

46Side Burner FrameP01108012B1

47Side Burner BodyP01108011B1

48Side Burner Pot SupportP00805010B1

49Side BurnerP02002012A1

50Side Burner ElectrodeP02614007C1

51Control Knob for Side Burner P03401043S1

52Hose Holder P05536001P1

Parts List for Models 6306LP & 6306NG

KEYDESCRIPTIONPART # QTY

53Side Burmer Control Knob SeatP03408053S1

Side Burner Gas Valve(LPG)Y00603491

Side Burner Gas Valve(NG)Y00603501

55Side Burner Connection HoseP03705029F1

56Grease Tray HandleP00213007B1

57Grease TrayP02717433C1

58Bowl Support Bracket, LeftP01301006B1

59Bowl Support Bracket, RightP01302006B1

60Rear Wind Shield, UpperP06906040C1

61Rear Wind Shield, LowerP0075202BC1

62Door Hinge Bracket, LeftP03302014A1

63Door Hinge Bracket, RightP03302015A1

64Cart Side Panel, LeftP07602020A1

Cart Side Panel, Right (LPG)P07603021A1

Cart Side Panel, Right (NG)P07603020A1

66Door BracketP01316005B1

67Door MagnetP05523001K4

67Door Stop PlateP05510014U1

68Cart Rear PanelP07701056A1

Cart Bottom Shelf (LPG)P01009038C1

Cart Bottom Shelf (NG)P01009039C1

71Caster Seat, Left FrontP05327027E1

72Caster Seat, Left Rear P05327029E1

73Caster Seat, Right Front P05327028E1

74Caster Seat, Right Rear P05327030E1

75Caster, 2.5 in., with BrakeP05117006E4

76Door HandleP00201001C2

77Door, LeftP04302035A1

78Door, RightP04303035A1

79Regulator with Hose (LPG)P03601032A1

80Lighting StickP05507031E1

81Side Burner Extension Hose (NG only)P03705082F1

82Regulator Assembly (NG)Y00800071

83 Hose, 12ft.(NG)P03704001A 1

84Side Burner Wind ShieldP06908003C1

Rotisserie AssemblyY02501091

Hardware Pack (For LPG & NG model)P06020005A1

Operator's ManualP80157005A1

To obtain the correct replacement parts for your gas grill, please refer to the part numbers in this parts

list. The following information is required to ensure you receive the correct parts:

1. Model and Serial Number (see CSA label on grill)

2. Part Number

3. Part Description

4. Quantity of parts needed

Important: Use only factory authorized parts. The use of any part that is not factory authorized can be

dangerous and will also void your product warranty. Keep this Operator's Manual for convenient referral

and for part replacement.

For the repair or replacement parts you need:

Call our Grill Information Center at 1-877-934-7455

Parts List for Models 6306LP & 6306NG

Y0250109 Rotisserie Assembly Parts Diagram

Hardware for Rotisserie

Grill Information Center: If you have questions about assembly or grill operation, or if there are damaged

or missing parts when you unpack this unit from the shipping box, call us 8:00 am - 4:30 pm CST,

Monday through Friday at: 1-877-934-7455

Y0250109 Rotisserie Assembly Parts List

KEY

PART#

DESCRIPTION

QTY

Rot. Bushing

Rot. 3/8"x1/2" Thumbscrew

Rot. Collar

Rot. Spit

Rot. Holding Fork

Rot. Handle

Rot. Motor Bracket

Rot. Motor/AC

Rot. #10-24x3/4" UNC Screw

Rot. Washer

Rot. #10-24 Nut

10.

11.

P05508092F

S196G06084

P05508091F

P05508163F

P05508090F

P05508076E

P03307028A

P07101010A

S112G10124

S411G03084

S362G10124

Rot. Screw#10-24x3/4"

UNC

Qty. 2

Part# S112G10124

Rot. Thumbscrew

3/8"x1/2"

Qty. 3

Part# S196G06084

Rot. Washer

Qty. 2

Part# S411G03084

Rot. Nut#10-24

Qty. 2

Part# S362G10124

Assembly Instructions

Remove all cart parts, hardware, and Grill Head from shipping boxes. Raise the Grill Lid and remove all packed

components. Use the parts list to check that all necessary parts have been included.

Assemble the gas grill on a protective work surface to avoid scratching grill surfaces. Inspect your grill for damage

as you proceed. Do not assemble or operate your grill if it appears damaged.

Place Left Cart Side Panel (parts are labeled L or R) upside down on the cardboard work

surface, reverse side of panel facing up. Install the Caster Seats (A,B) to Left Cart Side Panel

using 4 Countersink Flat Head Screws 3/16'’ x 3/8'’ and 4 Phillips Head Screws 1/4'’ x 1/2'’

Repeat for Right Cart Side Panel, install the Caster Seats (C,D) using 4 Countersink Flat

Head Screws 3/16'’ x 3/8'’ and 4 Phillips Head Screws 1/4'’ x 1/2'’.

Install Caster Seats

Install Cart Bottom Shelf and Casters

Phillips Head Screw

1/4" x 1/2"

Qty. 16

Part # S112G04081

Phillips Head Screw

1/4" x 1/2"

Qty. 8

Part # S112G04081

Countersink Flat Head Screw

3/16"x3/8"

Qty. 8

Part # S142G03061

Cart Side Panel, Left

3/16" x 3/8"

Countersink Flat Head Screw

1/4" x 1/2"

Phillips Head Screw

Cart Side Panel, Left

Cart Side Panel, Right

Cart Bottom Shelf - Tank Hole

Install Cart Bottom Shelf to Left and Right Cart Side Panel with 8 Phillips Head Screws 1/4" x 1/2".

(NOTE: Be sure that the tank hole is positioned to the right).

Install the 4 Casters onto Caster Seats as shown.

Install the Top Left Door Hinge Bracket to the Left Cart Side Panel with 2 Phillips Head Screws 3/16'’

x 3/8'’ and 2 Flange nuts 3/16'’. Do not tighten both screws immediately.

Insert Bottom Left Door Hinge into Bottom Left Door Hinge Bracket. Then align Top Door Hinge and

insert into the hole on Top Left Door Hinge Bracket and tighten securely the 2 screws.

Repeat both steps for Right Door.

Install Right and Left Door

Install the Cart Rear Panel between the Cart Side Panels

using 4 of 3/16” x 3/8” Phillips Head Screws and 4 of 3/16”

Flange Nuts.

Install Cart Rear Panel, Door Stop Plate and Door Handles

Install the Door Stop Plate to Bottom Shelf using 2 Countersink

Flat Head Screws 3/16” x 3/8” and 2 Flange Nuts 3/16” .

Install the Door Handles to Doors using 4 Phillips Head

Screws 3/16” x 1/4”.

Flange Nut 3/16"

Qty. 6

Part # S313G03061

Countersink Flat Head Screw

3/16"x3/8"

Qty. 2

Part # S142G03061

Phillips Head Screw

3/16" x 3/8"

Qty. 4

Part # S112G03061

Flange Nut 3/16"

Qty. 4

Part # S313G03061

Phillips Head Screw

3/16"x1/4"

Qty. 4

Part # S112G03041

Top Door

Hinge

Top Left

Door Hinge

Bracket

Phillips Head Screw

3/16" x 3/8"

Qty. 4

Part # S112G03061

Door Handle

Qty. 2

Part # P00201001C

Scale 1:2

Self Tapping Screw

M4 x 10mm

Qty. 1

Part # S172M04101

Install Door Bracket, Grill Bowl and Lighting Stick

Install Side Shelf Brackets

Flange Nut 3/16"

Qty. 4

Part # S313G03061

Phillips Head Screw

3/16" x 3/8"

Qty. 4

Part # S112G03061

Phillips Head Screw

1/4" x 1/2"

Qty. 8

Part # S112G04081

Remove cooking components from Grill Head. With an

assistant, lift and position Grill Head on the Cart. Tighten

securely using 4 Phillips Head Screws 1/4”x1-3/16”.

Install the Door Bracket between the Left and Right Cart

Side Panel using 4 of 3/16” x 3/8” Phillips Head Screws

and 4 Flange Nuts 3/16”.

Install the Lighting Stick to Left Bowl Panel using 1

Self Tapping Screw M4 x 10mm.

Attach the Side Shelf Bracket (A) to the Rear of Right Bowl Panel.

Attach the Side Shelf Bracket (B) to the Front of Right Bowl Panel.

Tighten securely using Phillips Head Screws 1/4” x 1/2”.

Repeat for Left Side Shelf Brackets.

Side Shelf Bracket, (A)

Side Shelf Bracket, (B)

IMPORTANT: Lock 4 casters.

Lighting Stick

Qty. 1

Part # P05507031E

Scale 1:2

Phillips Head Screw

1/4" x 1-3/16"

Qty. 4

Part # S112G04191

Place the Side Shelf over the Left Side Shelf Brackets and

Side Burner Frame over the Right Side Shelf Brackets.

Tighten securely using Screws and Nuts provided.

Install Side Shelf and Side Burner Frame

Phillips Head Screw

1/4" x 1/2"

Qty. 8

Part # S112G04081

Flange Nut 1/4"

Qty: 8

Part # S313G04081

Install Grease Tray

Install Grease Tray Heat Shield on Grease Tray.

From the front of the grill, slide the assembled Tray

side tabs over the side rails underneath the Grill Bowl.

Grease Tray

Grease Draining Tray

Heat Shield

Flange Nut 1/4"

Qty: 2

Part # S313G04081

Install the Towel Bar and Tool Hooks using 2 Flange Nuts 1/4”

as shown.

Install Tool Holder and Tool Hooks

Install the Connection Hose with Brass Nut attached to the

Gas Fitting and tighten securely.

Install Connection Hose

Connection Hose

Hose Holder

Qty. 1

Part # P05536001P

Scale 1:2

Flange Nut 3/16"

Qty. 2

Part # S313G03061

Phillips Head Screw

3/16" x 3/8"

Qty. 2

Part # S112G03061

Hose Holder

Qty. 1

Part # P05536001P

Scale 1:2

Phillips Head Screw

3/16" x 3/8"

Qty. 2

Part # S112G03061

Place the Natural Gas regulator hose through the hole on Right

Cart Side Panel. Tighten securely using Brass Nut found in

the NG Regulator. See Fig. 1.

Secure the Natural Gas Regulator Hose onto Hose Holder

on Cart Rear Panel using the Hose Holder, Screws and

Nuts provided. See Fig. 2.

Install Regulator Assembly (For NG model only)

Figure 2

Place the Regulator with Hose ( LPG) inside the cart

through the opening above Cart Rear Panel. Secure

the Regulator with Hose ( LPG) onto Cart Rear Panel

using the Hose Holder, Screws and Nuts provided.

Install Regulator Assembly (For LPG model only)

Flange Nut 3/16"

Qty. 2

Part # S313G03061

LPG Regulator

Cart Rear Panel

Hose

Hose Holder

NG Regulator

Cart Rear Panel

NG Regulator

Connection Hose

Cart Side Panel,

Right

Brass Nut

Figure 1

Hose Holder

Hose

WARNING

Failure to read and follow the Use and Care

Instructions could result in a fire or explosion

that could cause serious bodily injury, death or

property damage.

Final Grill Assembly Step

When you have finished assembling your

grill be sure that all screws are tightened

for safe operation of your grill.

Install Ignitor Battery

Unscrew Ignitor Cap from Control Panel.

Place supplied AA battery into the Ignitor

Slot with positive pole facing you.

Position the Cap and Spring over the AA

battery and tighten onto Control Panel.

With the assistance of another person,

perform this Electrode Check before

proceeding.

Be sure all Control Knobs are set to

"OFF" and open the Grill Lid.

Have your assistant stand behind to the

right of the grill and look toward the front

of the grill bowl. Never put your face

inside the Grill Head.

Press the Ignitor Cap. You should hear

a "clicking" sound. Your assistant should

see a blue spark within each Gas

Collector Box. If a spark is present the

Electrode Tips are properly positioned.

If no spark is seen, the Spark Gap

needs to be adjusted as follows:

This test will ensure that the Spark Electrode Tips

are properly positioned so your grill lights easily

and properly.

•

Using an adjustable wrench, loosen the

Inside Nut until the Gas Collector Box can

be turned upward.

If the gap between the Spark Elec-

trode Tip and Receiver is more than

3/16" use long nose pliers to gently

squeeze the Gas Collector Box to

narrow gap.

Return the Gas Collector Box to its

original position, secure the Inside Nut

and try the Electrode Check again. If no

"clicking" sound is heard:

AA Battery may be installed back-

wards.

Electric wires may be loose. Remove

the AA Battery and inspect the Ignitor

Junction Box found behind the Control

Panel and reconnect any loose wires.

Side Burner Electrode Check

Open side burner lid. Remove plastic

shipping band from burner and pot

support.

Push and turn side burner Control Knob

to HIGH. Look for spark between tip of

electrode and burner.

If you don't see a spark from side burner elec-

trode, adjust gap between electrode and

burner surface to 3/16 in.

Spark Gap

Gas Collector Box

Spark Electrode Tip

Spark Receiver

Inside Nut

Install Cooking Components

Place the Savor Plates

above the

Burners.

Place the Cooking Grids on the ledge

above the Savor Plates

Place the Secondary Cooking Rack on

the slots on either side of the Grill

Bowl.

Savor Plates

Cooking Grids

Secondary Cooking Rack

Ignitor Slot

AA Battery

Ignitor Cap

Spring

Rotisserie Assembly Instructions

Remove all components from the carton.

Attach the Motor Bracket on the outside of the left grill bowl panel. Align the two holes of the Bracket

with the holes on the grill bowl. Tighten securely using two Screws #10-24x3/4" UNC, Plain Washers

and Nuts provided.

Slide the Holding Forks onto each end of the Rotisserie Spit. Adjust spacing between Holding

Fork to accommodate your food, then tighten the Thumbscrews to keep the Holding Forks in

position. Slide the Collar and Bushing onto the the threaded end of the Spit. Do not tighten the

Collar Thumbscrew until the Rotisserie is placed into your grill.

Rot. Screw #10-24x3/4" UNC

Qty. 2

Part# S112G10124

Rot. Washer

Qty. 2

Part# S411G03084

Rot. Nut #10-24

Qty. 2

Part# S362G10124

Washer#10-24 Nut.

Rot. Screw#10-24x3/4"

UNC with washers

and nuts

Outside of left grill

bowl panel

Motor Bracket

Thumbscrew

3/8"x1/2"

Collar

Holding Forks

Thumbscrew

3/8"x1/2"

Bushing

Spit

Handle

Rot.Thumbscrew 3/8"x1/2"

Qty. 3

Part# S196G06084

The Bushing and Collar must always be used with this Rotisserie.

BEFORE rotisserie cooking you will need to remove the Cooking Grid(s) and possibly the Savor Plates

from your grill. When rotisserie cooking place a Cooking Pan under the food to be cooked. This will

capture the drippings and keep your grill clean of excess grease which could cause a fire. Use caution

when moving a Cooking Pan containing hot oils.

Install the AC (alternating current) Rotisserie Motor onto the Motor Bracket as shown below. Be sure

the Motor attaches to the Bracket with the electrical cord down. This installation ensures that once

the Spit is inserted into the Motor it will also rest securely into the slot of your grill bowl.

Insert the assembled Rotisserie into the Motor as shown below. The Motor should be on the left side

of your grill. Place the Bushing into the slot opening on the Right side of your grill bowl, then tighten

the Collar Thumbscrew to the right of the Bushing. The Collar will stabilize the Rotisserie during the

cooking process and the Bushing allows the Rotisserie Spit to turn smoothly. Plug the Rotisserie into

an outlet and turn on to test.

Rotisserie Motor

Motor Bracket

Rotisserie Spit must rest securely

into the slot of your grill bowl.

Handle

Bushing

Collar

Thumbscrew

Spit

Holding Forks

Thumbscrew

Motor

CORRECT LP GAS TANK USE

LP Gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas (LP Gas) tank,

not included with grill. Never connect your gas grill to

an LP Gas tank that exceeds this capacity. A tank of

approximately 12 inches in diameter by 18-1/2 inches

high is the maximum size LP Gas tank to use. You

must use an "OPD" gas tank which offers a listed

Overfill Prevention Device. This safety feature

prevents tank from being overfilled which can cause

malfunction of LP Gas tank, regulator and/or grill.

Never connect an unregulated LP gas tank to your

gas grill. The gas regulator assembly supplied with

your gas grill is adjusted to have an outlet pressure

of 11" water column (W.C.) for connection to an LP

gas tank. Only use the regulator and hose assembly

supplied with your gas grill. Replacement regulators

and hose assemblies must be those specified by

the Manufacturer.

Have your LP Gas dealer check the release valve

after every filling to ensure it remains free of defects.

Always keep LP Gas tank in upright position.

Do not subject the LP Gas tank to excessive heat.

Never store an LP Gas tank indoors. If you store

your gas grill in the garage always disconnect the

LP Gas tank first and store it safely outside.

LP Gas tanks must be stored outdoors in a well-

ventilated area and out of the reach of children.

Disconnected LP Gas tanks must not be stored in a

building, garage or any other enclosed area.

The regulator and hose assembly can be seen after

opening the doors (if applicable) and must be

inspected before each use of the grill. If there is

excessive abrasion or wear or if the hose is cut, it

must be replaced prior to using the grill again.

Never light your gas grill with the lid closed or

before checking to ensure the burner tubes are fully

seated over the gas valve orifices.

Never allow children to operate your grill. Do not

allow children or pets to play near your grill.

The LP Gas tank must be constructed and marked

in accordance with the Specifications for LP-Gas

Cylinders of the U.S. Department of Transportation

(D.O.T.) or the National Standard of Canada, CAN/

CSA-B339, Cylinders, Spheres and Tubes for

Transportation of Dangerous Goods and Commis-

sion, as applicable.

The LP Gas tank must have a shutoff valve,

terminating in an LP Gas supply tank valve outlet,

that is compatible with a Type 1 tank connection

device. The LP Gas tank must also have a safety

relief device that has a direct connection with the

vapor space of the tank.

The tank supply system must be arranged for vapor

withdrawal.

The LP Gas tank used must have a collar

to protect the tank valve.

WARNING

Do not store a spare LP-Gas tank under or near

this appliance.

Never fill the tank beyond 80 percent full; and

If the information in "(a)" and "(b)" is not followed

exactly, a fire causing death or serious injury may

occur.

•

WARNING

! !

Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area.

Never obstruct the flow of ventilation air around

your gas grill housing.

Use of alcohol or drugs may impair the ability to

assemble and operate the appliance.

Keep fire extinguisher readily accessible. In the

event of a oil/grease fire, do not attempt to

extinguish with water. Use type B extinguisher

or smother with dirt, sand or baking soda.

In the event of rain, cover the grill and turn off

the burner and gas supply.

Use your grill on a level, stable surface in an

area clear of combustible materials.

Do not leave grill unattended when in use.

Do not move the appliance when in use.

Allow the grill to cool before moving or storing.

Do not use your grill as a heater.

This grill is not intended to be installed in

or on recreational vehicles and/or boats.

USE AND CARE INSTRUCTIONS

Use your grill at least 3 feet away from any

wall or surface. Use your grill at least 3 feet

away from combustible objects that can melt

or catch fire (such as vinyl or wood siding,

fences and overhangs) or sources of ignition

including pilot lights on water heaters and live

electrical appliances.

If growing bubbles appear do not use or move

the LP Gas tank. Contact an LP Gas Supplier

or your fire department!

WARNING

NOTE about LP Gas Tank Exchange Programs

Many retailers that sell grills offer you the option of

replacing your empty LP Gas tank through an ex-

change service. Use only those reputable exchange

companies that inspect, precision fill, test and certify

their tanks. Exchange your tank only for an OPD safety

feature-equipped tank as described on page19 of this

manual.

How to Leak Test your LP Gas Tank

LP Gas Model only:

Secure a 20lb LP Gas Tank to Gas Grill

Turn your LP Gas Tank Valve clockwise to the

closed or OFF positon.

Place LP Gas tank into tank hole on bottom shelf.

Install the tank so the Tank Valve faces the rear

right corner of cabinet.

Screw the Wing Bolt in to secure the gas tank.

Use a clean paintbrush and a 50/50 mild soap and

water solution.

Brush soapy solution onto LP Gas tank in the

areas indicated by the arrows. See diagram.

If growing bubbles appear do not use or move the

LP Gas tank. Call an LP Gas Supplier or your Fire

Department.

All leak tests must be repeated each time your LP

Gas tank is exchanged or refilled.

When checking for gas leaks do not smoke.

Do not use an open flame to check for gas leaks.

Your grill must be leak tested outdoors in a well-

ventilated area, away from ignition sources such as

gas fired or electrical appliances. During the leak test,

keep your grill away from open flames or sparks.

Do not use household cleaning agents. Damage to

gas assembly components can result.

For your safety:

Leak test new and exchanged LP Gas tanks BEFORE

connecting one to your grill.

Always keep new and exchanged LP Gas tanks in an

upright position during use, transit or storage.

Wing Bolt 5/16"x4-1/2"

Qty. 1 (LPG model)

Part# S233G05461

Scale 1:2

USE AND CARE INSTRUCTIONS

Page is loading ...

Grand Hall 6306LP Owner's manual

Brand: Grand Hall

Model: 6306LP

Category: Barbecues & grills

Type: Owner's manual

Download PDF

report

Grand Hall 6306LP Owner's manual

Grand Hall 6306LP Owner's manual

Related papers

Other documents