Lucent Technologies CIB 3023 User manual

Brand: Lucent Technologies

Model: CIB 3023

Category: Wall & ceiling mounts accessories

Type: User manual

CIB 3023

(Z7309H01B) 10-Button Hands-Free

Answer on Intercom (HFAI) Voice

Terminal (3161)

CIB 3023

Comcode 105-253-025

Issue 3

CIB 3023

(Z7309H01B) 10-Button Hands-Free Answer on

Intercom (HFAI) Voice Terminal (3161)

The 10-Button HFAI Voice Terminal (Figure 1) allows you to program

and use all the custom features that your communications system pro-

vides. It also permits you to answer and talk on announced intercom

calls without lifting your handset. Included with these instructions for ins-

talling your HFAI Voice Terminal is a User’s Card with instructions for

using the voice terminal. Keep it handy for quick reference.

Handset jack

FIGURE 1 The 10-Button HFAI Voice Terminal

Assembling Your Voice Terminal

●

Your 10-Button HFAI Voice Terminal comes with the following com-

ponents:

Voice terminal body

Handset (with handset cord attached)

Modular voice terminal cord

Plastic desk stand/wall mount (with rubber feet attached)

The pieces of the desk stand/wall mount come attached to one another

(Figure 2), with the names Base, Desk Support, and Wall Support

iss 3, cib3023-1

imprinted on the appropriate pieces. Separate instructions follow for

each application.

Desk

support

Runner

Wall

support

Base

FIGURE 2 Unassembled Desk Stand/Wall Mount

DESK STAND ASSEMBLY

Break the pieces of the desk stand/wall mount away from the runner.

Discard the runner.

Find the stand pieces labeled Base and Desk Support. File the rough

edges off these pieces where they were attached to the runner.

Insert the tabs labeled A and B on the desk support into the slots

labeled A and B on the base (Figure 3).

Desk support

Base

FIGURE 3 Assembling the Desk Stand

iss 3, cib3023-2

Turn the voice terminal upside down, and position the stand on the

voice terminal so that the stand’s mounting slots (Figure 4A) fit just

below the voice terminal’s mounting tabs (Figure 4B).

Mounting

slots

Mounting

tabs

Locking

tab

Stand attached

to voice terminal

(bottom view)

FIGURE 4 Attaching the Voice Terminal to the Desk Stand

Gently slide the stand upward so that the voice terminal tabs fit

securely in the three mounting slots on the stand (Figure 4C). Press

down on the stand to secure the locking tab.

Thread one end of the modular voice terminal cord between the base

of the desk stand and the bottom of the voice terminal, and plug it

into the jack labeled Line on the bottom of the voice terminal.

Turn the voice terminal right side up, and place the handset in the

cradle (Figure 5).

iss 3, cib3023-3

Desk support

FIGURE 5 10-Button HFAI Voice Terminal Attached to the Desk Stand

Check to see that one end of the handset cord is attached to the

handset. If it is not, plug it into the handset now.

Plug the other end of the handset cord into the jack on the middle

front of the voice terminal.

Plug the other end of the modular voice terminal cord into the build-

ing wiring connection, which is either a modular voice terminal exten-

sion cord or a modular voice terminal jack (Figure 6).

terminal extension

cord

Modular

voice terminal

cord

Modular voice

Modular voice terminal

jack

FIGURE 6 Attaching the Voice Terminal Cord to Building Wiring

iss 3, cib3023-4

To remove the 10-Button HFAI Voice Terminal from the desk stand,

set the handset aside, turn the voice terminal upside down, and

unplug the modular voice terminal cord. Press down on the locking

tab to release the stand, and slide the stand down and away from the

voice terminal.

WALL MOUNT ASSEMBLY

Installing the Wall Mount

Break the pieces of the desk stand/wall mount away from the runner.

Discard the runner.

Find the pieces labeled Base and Wall Support, and file the rough

edges off these pieces where they were attached to the runner.

Use the tip of a screwdriver or other similar device to remove the four

rubber feet in the corners on the bottom of the base.

Place the base upside down on a table or desk and insert the tabs

labeled A and B on the wall support into the slots labeled A and B on

the base (Figure 7).

Tab B

Tab A

Bottom of base

FIGURE 7 Assembling the Wall Mount

Lift the base and push the wall support through the slots until it clicks

into place. Turn the base over.

iss 3, cib3023-5

Select a mounting space at least as large as the voice terminal. Use

the base as a template and mark the four mounting screw locations

on the wall.

Unpack the hardware kit, which was ordered separately from the

voice terminal. Select the proper-sized toggle bolts for your wall

thickness.

●

For walls 3/8” to 1/2” thick, use the smaller of the two sizes of

toggle bolts.

●

For walls 5/8” to 3/4” thick, use the larger of the two sizes.

●

For solid walls, either of the two sizes may be used.

Using a 5/16” drill bit, drill a hole at each of the four previously

marked mounting screw locations on the wall.

Insert one toggle bolt into each of the four drilled holes (Figure 8A).

Gently tap each toggle bolt with a hammer until it is flush with the wall

(Figure 8B).

Insert the red key (provided with the hardware kit) into the toggle bolt,

and push with your fingertip (do not force or hammer the red key) to

pop open the toggle inside the wall (Figure 8C). Remove the red

key.

Red key

FIGURE 8 Installing Toggles for Wall Mount

Using a 3/16” drill bit, enlarge the four mounting screw holes in the

base.

Line up the holes in the base with the toggle bolts.

iss 3, cib3023-6

Insert the top two screws into the base, and partially thread the

screws into the toggles. Insert the two remaining screws into the

lower mounting holes.

Tighten all four screws (Figure 9).

Top of base

FIGURE 9 Wall Mount Attached to Wall

Converting the Voice Terminal for Wall Mounting

1 Remove the number card retainer with a straightened paper clip or

similar device, and remove the number card (Figure 10).

Switchhook

button

Number card

retainer

Paper clip

FIGURE 10 Removing the Number Card and Retainer

iss 3, cib3023-7

Remove the screw under the number card, and lift out the handset

retainer from the upper housing (Figure 11).

Handset retainer

screw

Handset

retainer

FIGURE 11 Handset Retainer and Screw

Rotate the handset retainer 180 degrees (Figure 12).

Rotate to

wall mount

position

Handset retainer

removed

Handset retainer

screw removed

FIGURE 12 Rotating the Handset Retainer

Replace the handset retainer. When properly inserted, the handset

retainer extends out from the handset cradle (Figure 13).

iss 3, cib3023-8

Handset

retainer

Handset retainer

after rotation

Handset

retainer

Handset

screw

retainer

screw

FIGURE 13 Handset Retainer in Wall Mount Position

Replace the screw, the number card, and the number card retainer.

Plug one end of the modular voice terminal cord into the jack labeled

Line on the bottom of the voice terminal.

Position the voice terminal so that its mounting tabs (Figure 14A) fit

just above the mounting slots on the wall mount (Figure 14B).

Arrange the modular voice terminal cord so that it rests between the

base of the wall mount and the bottom of the voice terminal.

Slide the voice terminal down carefully so the mounting tabs fit

securely in the three mounting slots (Figure 14C). Gently press the

voice terminal against the wall mount to secure its locking tab.

iss 3, cib3023-9

Voice terminal

(back view)

Mounting tabs

Wall mount

Mounting

slots

Jack for

handset

cord

Wall mount

(top view)

FIGURE 14 Attaching the 10-Button HFAI Voice Terminal to the Wall Mount

Check to see that one end of the handset cord is attached to the

handset. If it is not, Plug one end into the handset now.

Plug the other end of the handset cord into the jack on the middle

front of the voice terminal (Figure 14C). Place the handset into the

cradle.

Plug the other end of the modular voice terminal cord into the build-

ing wiring connection, which is either a modular voice terminal exten-

sion cord or a modular voice terminal jack (Figure 6).

To remove the voice terminal from the wall mount, unplug the

handset cord from the voice terminal and set the handset aside.

Slide the voice terminal up and away from the wall mount.

Testing

Your Voice Terminal

Use the Test/Program (T/P) switch on the left side of the voice terminal

to test the lights and ringing. After assembling the voice terminal, slide

the T/P switch away from you to the T position (Figure 15). If the voice

terminal is working properly, the red and green lights flash and the voice

terminal rings. If this does not happen, refer to the Troubleshooting

Tables in your system’s installation guide. If you still have a problem

after troubleshooting your system, call your equipment supplier. Slide

the T/P switch back to the center position.

iss 3, cib3023-10

Test/

Program

switch

Volume

control

FIGURE 15 T/P Switch and Volume Control

Setting the Volume

Use the volume control switch, located on the left side of the voice termi-

nal, to set the volume for the ringing, the speaker, and the button clicks

(Figure 15).

●

Slide the switch away from you to increase the volume.

●

Slide the switch toward you to decrease the volume.

The Button Label Sheet

REMOVING THE BUTTON LABEL SHEET

Remove the handset and set aside.

Insert a paper clip or similar device into the larger recessed opening

adjacent to the number card retainer (Figure 16). Gently lift up and

remove the plastic cover plate.

iss 3, cib3023-11

Plastic

cover

plate

Button

label

sheet

Recessed

openings

on face

plate

FIGURE 16 Removing the Button Label Sheet

Lift the button label sheet off the voice terminal.

Identify the buttons by typing or writing the information on the button

label sheet.

INSERTING THE BUTTON LABEL SHEET

Place the button label sheet on the voice terminal so that the holes

on the label sheet fit over the buttons. Press it gently into place with

your fingertips.

Replace the plastic cover plate on top of the label sheet, and press it

down.

ORDERING BUTTON LABEL SHEETS AND COVER PLATES

Call the AT&T National Sales Parts Center’s toll-free number 1-800-222-

PART to order:

Item

Order Number

(5) Button label sheets

105217368

(3) Cover plates

105203186

iss 3, cib3023-12

Handsets for the Hearing Impaired and for Noisy

Locations

All voice terminals come with a handset that is hearing-aid compatible.

Two other types of handsets are also available:

●

The (R6C3) Impaired-Hearing Handset (31753) has an extra amplifier

to provide greater volume in the earpiece. A thumbwheel volume

control on the handset allows the volume to be turned up or down, as

needed.

The (R8C3) Push-to-Listen Handset (31754) is for use in noisy loca-

tions. Like the impaired-Hearing Handset, the Push-to-Listen

Handset has an extra amplifier and a thumbwheel volume control. It

also has a pushbutton on the handset that increases the volume in

the earpiece and mutes background noise transmitted through the

mouthpiece.

iss 3, cib3023-13

User’s Card

10-Button Hands-Free Answer on Inercom (HFAI) Voice Terminal

Using the Hands-Free Answer on Intercom Feature

(See your user’s guide for information on other features.)

The Hands-Free Answer on Intercom Voice Terminal allows you to answer intercom calls

without lifting your handset. If you lift your handset, you turn off the Hands-Free Answer on

Intercom feature and you cannot reactivate it during the call in progress.

The green light next to the HFAI/Mic button tells you whether the feature is active. Press-

ing the button activates the feature (the green light goes on). Pressing the button again

turns off the feature (the green light goes off). During an HFAI call this green light flashes

indicating the microphone is on.

HANDS-FREE ANSWER ON INTERCOM CALLS

Activate HFAI feature before

receiving calls:

Answer intercom call:

●

End call:

Press HFAI/Mic.

You hear a beep announcing an intercom call.

The red light next to the Intercom button

comes on, and the green lights next to it and

HFAI/Mic flash on and off.

If you have an Auto Intercom button for the

caller, the green light next to it flashes quickly.

Without lifting the handset, begin speaking.

Press Speaker.

●

OTHER FEATURES

Mute Microphone:

●

Press HFAI/Mic. The flashing green light next

to it goes off.

iss 3, cib3023-14

Lucent Technologies CIB 3023 User manual

Brand: Lucent Technologies

Model: CIB 3023

Category: Wall & ceiling mounts accessories

Type: User manual

Download PDF

report

Lucent Technologies CIB 3023 User manual

Lucent Technologies CIB 3023 User manual

Related papers

Other documents