2. Computers & electronics
  3. TVs & monitors
  4. Flat panel accessories
  5. Sharp
  6. PN-70SC3
PN-70SC3

Sharp PN-70SC3, PN70SC3 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Sharp PN-70SC3 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
LCD MONITOR
MONITEUR LCD
MONITOR LCD
LCD FARBMONITOR
Жидкокристаллический дисплей
для просмотра видеоизображения
SETUP MANUAL
MANUEL D’INSTALLATION
MANUAL DE INSTALACIÓN
INSTALLATIONSANLEITUNG
РУКОВОДСТВО ПО УСТАНОВКИ
ENGLISH ...... E1
FRANÇAIS ..... F1
ESPAÑOL .... S1
DEUTSCH ..... D1
РУССКИЙ...... Р1
(

CD-ROM

)
香港電器安全規格

國際電工委員會規格適合
）
PN-70SC3
ENGLISH FRANÇAIS ESPAÑOLENGLISH FRANÇAIS ESPAÑOL DEUTSCH РУССКИЙ
Information on the Disposal of this Equipment and its Batteries
IF YOU WISH TO DISPOSE OF THIS EQUIPMENT OR ITS BATTERIES, DO NOT USE THE ORDINARY WASTE
BIN, AND DO NOT PUT THEM INTO A FIREPLACE!
Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance with local law.
Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing nal disposal of waste. IMPROPER DISPOSAL can be
harmful to human health and the environment due to certain substances! Take USED EQUIPMENT to a local, usually municipal, collection facility, where available.
Remove USED BATTERIES from equipment, and take them to a battery collection facility; usually a place where new batteries are sold.
If in doubt about disposal, contact your local authorities or dealer and ask for the correct method of disposal.
ONLY FOR USERS IN THE EUROPEAN UNION, AND SOME OTHER COUNTRIES; FOR INSTANCE NORWAY AND SWITZERLAND: Your
participation in separate collection is requested by law.
The symbol shown above appears on electrical and electronic equipment and batteries (or the packaging) to remind users of this. If ‘Hg’ or ‘Pb’ appears
below the symbol, this means that the battery contains traces of mercury (Hg) or lead (Pb), respectively.
Users from PRIVATE HOUSEHOLDS are requested to use existing return facilities for used equipment and batteries.
Batteries are collected at points of sale. Return is free of charge.
If the equipment has been used for BUSINESS PURPOSES, please contact your SHARP dealer who will inform you about take-back. You might be
charged for the costs arising from take-back. Small equipment (and small quantities) might be taken back by your local collection facility. For Spain:
Please contact the established collection system or your local authority for take-back of your used products.
Information sur la mise au rebut de cet Équipement et de ses Piles
SI VOUS VOULEZ METTRE AU REBUT CET ÉQUIPEMENT OU SES PILES, N’UTILISEZ PAS LA POUBELLE
ORDINAIRE! NE LES BRULEZ PAS DANS UNE CHEMINÉE!
Un équipement électrique et électronique usagé et les batteries devraient toujours être collectés et traités SÉPARÉMENT conformément à la loi en vigueur.
La collecte sélective permets un traitement respectueux de l’environnement, le recyclage des matériaux et minimise la quantité de déchets mise en
traitement ultime. Une MISE AU REBUT INCORRECTE peut être nuisible pour la santé humaine et l’environnement en raison de certaines substances!
Déposez l’ÉQUIPEMENT USAGÉ dans une déchetterie, souvent gérée par la municipalité, si disponible.
Retiré les PILES USAGÉS de l’équipement et déposez-les dans un collecteur approprié; d’habitude situé chez les commerçants vendant des piles neuves.
Si vous avez un doute lors de la mise au rebut, rentrez en contact avec les autoritĂŠs locales ou votre revendeur et demandez la bonne mĂŠthode.
Pour les UTILISATEURS se trouvant dans L’UNION EUROPÉENNE ET dans quelques AUTRES PAYS comme par exemple LA NORVÈGE ET LA
SUISSE : Votre participation Ă  la collecte sĂŠlective est encadrĂŠe par la loi.
Le symbole ci-dessus apparait sur l’équipement électrique et électronique et sur les piles (ou leurs emballages) an de rappeler aux utilisateurs qu’il
faut les collecter sĂŠparĂŠment.
Si ‘Hg’ ou ‘Pb’ apparaissent au-dessous du symbole, cela signie que la pile contient des traces de mercure (Hg) ou de plomb (Pb).
Les utilisateurs de PRODUITS MÉNAGER doivent utiliser des points de collecte existants pour les équipements usagés et les piles. Les piles peuvent
ĂŞtre collectĂŠes aux points de vente. Elle est gratuite.
Si l’équipement a été utilisé dans le MILIEU PROFESSIONNEL, entrez s’il vous plaît en contact avec votre revendeur SHARP qui vous informera de la procédure
existante. A cette n, vous pourriez être facturé pour les dépenses résultant de cette collecte. Les petits équipements (et les faibles quantités) pourrait être collectés par
votre déchèterie. Pour l’Espagne :entrez s’il vous plaît en contact avec le système de collecte établi ou votre collectivité locale pour la collecte de vos produits usagés.
InformaciĂłn sobre la eliminaciĂłn de ĂŠste aparato y sus pilas
SI USTED DESEA ELIMINAR ÉSTE APARATO O SUS PILAS, ¡NO UTILICE EL CONTENEDOR DE RESIDUOS
HABITUAL, Y NO LOS ARROJE AL FUEGO !
Los aparatos elĂŠctricos y electrĂłnicos y las pilas usadas deben ser recogidos y tratados SEPARADAMENTE de acuerdo con la ley.
La recogida selectiva promueve un tratamiento respetuoso con el medio ambiente, el reciclaje de materiales, y minimiza el desecho nal de residuos
¡LA ELIMINACIÓN INCORRECTA puede ser perjudicial para la salud humana y el medio ambiente, debido a las sustancias peligrosas contenidas!.
Lleve los APARATOS USADOS a un centro de recogida local, normalmente municipal, cuando estĂŠ disponible.
Retire las PILAS USADAS del aparato y llĂŠvelas a un centro de recogida de pilas, por lo general en el mismo lugar donde se venden pilas nuevas.
En caso de duda sobre la eliminaciĂłn del producto, contacte con su distribuidor o con las autoridades locales y pregunte por el mĂŠtodo correcto de eliminaciĂłn.
SÓLO PARA LOS USUARIOS DE LA UNIÓN EUROPEA, Y ALGUNOS OTROS PAÍSES, POR EJEMPLO NORUEGA Y SUIZA: Su participación en la
recogida selectiva es requerida por ley.
¡Él símbolo mostrado arriba aparece en los aparatos eléctricos y electrónicos y en las pilas (o en el embalaje) para recordárselo!
Si aparece “Hg” o “Pb” debajo del símbolo, signica que la pila contiene trazas de mercurio (Hg) o plomo (Pb), respectivamente.
Los usuarios procedentes de HOGARES PARTICULARES deberĂĄn utilizar las instalaciones existentes de retorno para los aparatos usados y sus
pilas. Las pilas se recogen en los puntos de venta. La devoluciĂłn es gratuita.
Si el equipo ha sido utilizado para FINES COMERCIALES, por favor pĂłngase en contacto con su distribuidor SHARP, quien le informarĂĄ sobre cĂłmo
gestionar su eliminaciĂłn. Es posible que se le cobre por los gastos derivados de la eliminaciĂłn.
Para aparatos pequeĂąos (y cantidades pequeĂąas) pueden ser recogidos por sus centros de recogida local. Para EspaĂąa: por favor pĂłngase en
contacto con el sistema de recogida establecido o con las autoridades locales para la recogida de los productos usados.
Informationen zur Entsorgung dieses Gerätes und der Batterien
WENN DIESES GERÄT ODER DIE BATTERIEN ENTSORGT WERDEN SOLLEN, DÜRFEN SIE WEDER ZUM
HAUSMÜLL NOCH IN EINE FEUERSTELLE GEGEBEN WERDEN!
Gebrauchte elektrische und elektronische Geräte und Batterien mßssen nach dem Gesetz GETRENNT gesammelt und entsorgt werden.
Mit der getrennten Sammlung werden die umweltfreundliche Behandlung und die stofiche Verwertung sichergestellt und die Rest-Abfallmengen
minimiert. Die ORDNUNGSWIDRIGE ENTSORGUNG schadet wegen schädlicher Stoffe der Gesundheit und der Umwelt! Bringen Sie GEBRAUCHTE
ELEKTRISCHE UND ELEKTRONISCHE GERÄTE zur einer örtlichen, meist kommunalen Sammelstelle, soweit vorhanden.
Entnehmen Sie zuvor die Batterien. Bringen Sie VERBRAUCHTE BATTERIEN zu einer Batterie-Sammelstelle; zumeist dort, wo neue Batterien verkauft werden.
Wenden Sie sich im Zweifel an Ihren Händler oder Ihre Ürtlichen BehÜrden, um Auskunft ßber die richtige Entsorgung zu erhalten.
NUR FÜR NUTZER IN DER EUROPÄISCHEN UNION UND EINIGEN ANDEREN LÄNDERN, Z.B. SCHWEIZ UND NORWEGEN: Ihre Mitwirkung bei
der getrennten Sammlung ist gesetzlich vorgeschrieben.
Das oben gezeigte Zeichen auf Gerät, Batterie oder Verpackung soll Sie darauf hinweisen! Wenn unter dem Zeichen noch ‘Hg’ oder ‘Pb’ steht, bedeutet
dies, dass Spuren von Quecksilber (Hg) or Blei (Pb) in der Batterie vorhanden sind.
Nutzer in PRIVATEN HAUSHALTEN mßssen die vorhandenen Rßckgabestellen fßr Altgeräte bzw. Altbatterien nutzen.
Altbatterien werden in den Verkaufsgeschäften gesammelt. Die Rßckgabe ist kostenlos.
Wurde das Gerät GESCHÄFTLICH genutzt, wenden Sie sich an Ihren SHARP-Händler, der Sie über die Wege zur Rücknahme des Gerätes informiert.
Es kÜnnen Kosten fßr Sie entstehen. Kleine Geräte und geringe Stßckzahlen werden mÜglicherweise auch von den vorhandenen Rßckgabestellen
fßr Altgeräte angenommen. In Spanien gilt: Wenden Sie sich an ein Sammelsystem oder Ihre Ürtlichen BehÜrden, um Auskunft ßber die richtige
Entsorgung zu erhalten.
ENGLISH
1
E
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within
a triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
DEAR SHARP CUSTOMER
IMPORTANT INFORMATION
Contents
[ENGLISH]
IMPORTANT INFORMATION ............................................1
DEAR SHARP CUSTOMER .............................................. 1
SAFETY PRECAUTIONS ..................................................2
SAFETY INSTRUCTION ...................................................4
MOUNTING PRECAUTIONS ............................................4
Supplied Components ..................................................... 5
Preparing the Remote Control Unit ................................ 5
Connections .....................................................................6
Turning Power On/Off ...................................................... 7
Specications ..................................................................8
Mounting Precautions
(For SHARP dealers and service engineers) ................. 8
Read the manuals in the provided CD-ROM. (Adobe Reader is required to view the manuals.)
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth
or coloured green or green-and-yellow.
• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly. If you are in any doubt consult a qualied electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”
2
E
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or re. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners. Do not use dirty cloths. Doing so may damage the product.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufcient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the screen breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage ows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualied service person to perform servicing.
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualied service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualied
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specied by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in re, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including ampliers).
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specied batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery uid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery uid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
ENGLISH
3
E
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
22. Do not modify this product.
23. To prevent re or shock hazard, do not expose this product to dripping or splashing.
No objects lled with liquids, such as vases, should be placed on the product.
24. This product must only be connected to a 100-240V, 50/60Hz, grounded (3-prong) outlet.
WARNING:
1) This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
2) Batteries shall not be exposed to excessive heat such as sunshine, re or the like.
3) To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with the installation instructions.
4) An apparatus with CLASS I construction shall be connected to a MAIN socket outlet with a protective earthing connection.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal,
D-sub input terminal, and RS-232C input terminal.
If a monitor is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using xing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
WARNING:
To prevent the spread of re, keep candles or other open ames away
from this product at all times.
SAFETY PRECAUTIONS (Continued)
4
E
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specications is
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor with the surface perpendicular to a level
surface.
• When moving the monitor, be sure to hold at the sides and
bottom. Do not grasp the screen or tray. This may cause
product damage, failure, or injury.
• This monitor should be used at an ambient temperature
between 41°F (5°C) and 95°F (35°C). Provide enough
space around the monitor to prevent heat from
accumulating inside.
7-7/8 [20]
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
2-3/16 [5.5]
• If it is difcult to provide sufcient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 41°F (5°C) to 95°F (35°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
• Do not use the product in locations where the unit is
exposed to direct sunlight or other strong light. Since this
product operates with infrared rays, such light may cause a
malfunction.
• When using multiple monitors closely, be sure the infrared
transmitter/receiver does not affect the other ones.
• After installing the monitor, afx the stand hole protection
covers.
SAFETY INSTRUCTION
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam. Do not use in an environment where
there are corrosive gases (sulfur dioxide, hydrogen sulde,
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this
could lead to re.
- Ensure that the monitor does not come into contact with
water or other uids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to re or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of re.
- Do not use the monitor in places where it may be exposed to
direct sunlight. Risk of cabinet deformation and failure if the
monitor is used in direct sunlight.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
- Do not operate the screen with a hard or pointed object such
as a ngernail or pencil.
The Power Cord
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in re or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to re as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
ENGLISH
5
E
Supplied Components
If any component should be missing, please contact your dealer.
* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Preparing the Remote Control Unit
Installing the batteries
1. Press the cover gently and slide it in the direction of the
arrow.
2. See the instructions in the compartment and put in the
supplied batteries (R-6 (“AA” size) x 2) with their plus (+)
and minus (-) sides oriented correctly.
3. Close the cover.

Liquid Crystal Display Monitor: 1

Power cord

Remote control unit: 1

Remote control unit battery
(R-6 (“AA” size)): 2

CD-ROM (Utility Disk): 1

Setup Manual (this manual): 1

Touch pen: 1

Tray: 1

Tray mounting screws (M3) : 5

Eraser: 1

USB extension cable: 1

Cable clamp (afxing type): 2

Stand hole protection cover: 2

Cover SHARP logo: 1
Place this sticker onto the SHARP logo to cover
the logo.
6
E
For power outlet
4
5
8
9
11
12
13
6
7
3
10
12
USB cable
Connections
Caution
• Be sure to turn off the power and disconnect the plug from the power outlet before connecting/disconnecting cables. Also,
read the manual of the equipment to be connected.
• Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables
connected to the input and output terminals may cause malfunctions and the other problems.
TIPS
• To use the touch panel, the monitor must be connected to a computer using a USB cable.
You can use the supplied USB extension cable to extend the cable.
• The touch panel operates with the standard Window driver.
• The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks
of HDMI Licensing, LLC in the United States and other countries.
1. AC input terminal
2. Power cord (Supplied)
3. HDMI 3 input terminal (INPUT3)
4. HDMI 2 input terminal (INPUT2)
5. HDMI 1 input terminal (INPUT1)
6. Audio input terminal (for INPUT2/INPUT6)
7. Audio input terminal (for INPUT4)
8. AV component input terminals (INPUT4)
9. AV video input terminal (INPUT5)
10. Audio input terminal (for INPUT5)
11. Audio output terminal
12. D-sub input terminal (INPUT6)
13. RS-232C input terminal
ENGLISH
7
E
Turning Power On/Off
Caution
• Whenallconnectionsarecomplete,turnonthepower.
• Turnonthemonitorrstbeforeturningonthecomputeror
playbackdevice.
• EvenwhenthepoweristurnedoffwiththePOWERbutton
onthemonitor,aminuteamountofpowerisconsumedif
thepowercordisconnected.
Turning power on/off
1. Press the POWER button on the side of the monitor to
turn on the power.
ThepowerLEDlightsgreen.
Remote control sensor Power LED
Status Status of the monitor
Greenlit Poweron
Redlit Standbymode
2. Turn the power on and off with the POWER button on
the remote control.
Pointtheremotecontrolunittowardtheremotecontrol
sensoronthemonitor,andpressthePOWERbutton.
Caution
•
Whenturningthepoweroffandbackon,alwayswaitforat
least5seconds.Ashortintervalmayresultinamalfunction.
• Foracompleteelectricaldisconnection,pulloutthemain
plug
n
Operation mode
Whenthemonitoristurnedonforthersttimeafterbeing
shippedfromthefactory,theoperationmodesettingscreen
willbedisplayed.SetittoMODE1orMODE2.
MODE1...OFFIFNOOPERATIONissetto4HR..(These
 settingscannotbechanged.)
Ifthereisnooperationfor4hoursormore,the
monitorautomaticallyentersstandbymode.
MODE2...Willperformstandardoperation.
OFFIFNOOPERATIONissettoDISABLE.These
settingscanbechanged.
Evenafterbeingset,changescanbemadeusing
OPERATIONMODE,locatedinthemenuofthemonitor.(See
OPERATIONMANUAL.)
8
E
• When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
Screws (M6)
Bracket
The monitor mounting
5/16 - 3/8 inch (8-10 mm)
• Do not use an impact driver.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
n
Attaching the Tray
Secure the tray using 5 tray mounting screws (M3) (supplied).
Specications
Model PN-70SC3
Power requirement AC 100 V - 240 V, 2.7 A, 50/60 Hz
Operating temperature 41°F to 95°F (5°C to 35°C)
Operating humidity 20% to 80% (no condensation)
Power consumption (Maximum) 235 W
Dimensions (excluding protrusions) inch (mm)
Approx. 64-5/16 (W) x 4-5/16 (D) x 39-1/8 (H) (1633 x 109 x 994.5)
Weight lbs. (kg)
Approx. 123.5 (56)
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
Mounting Precautions (For SHARP dealers and service engineers)
FRANÇAIS
1
F
Table des matières
[FRANÇAIS]
AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, NE PAS
EXPOSER CE PRODUIT À LA PLUIE OU À LA POUSSIÈRE.
RISQUE DE
DÉCHARGE
ÉLECTRIQUE
NE PAS OUVRIR
ATTENTION
ATTENTION : POUR RÉDUIRE LE RISQUE DE
DÉCHARGE ÉLECTRIQUE, NE PAS
RETIRER LE COUVERCLE. IL N’Y A
AUCUNE PIÈCE RÉPARABLE PAR
L’UTILISATEUR À L’INTÉRIEUR.
AVERTIR LE PERSONNEL DE
SERVICE QUALIFIÉ POUR TOUTE
PROCÉDURE D’ENTRETIEN.
Le symbole représenté par l’éclair à la tête en
pointe de èche à l’intérieur d’un triangle, est
placé pour alerter l’utilisateur de la présence
d’une “tension dangereuse” non isolée à l’intérieur
du produit. Cette tension peut avoir une valeur
sufsante pour constituer un risque
d’électrocution à toute personne.
Le point d’exclamation à l’intérieur d’un triangle
est placé pour alerter l’utilisateur de la présence
d’une procédure particulière ou d’une procédure
de maintenance (entretien) importante dans les
manuels accompagnant le produit.
INFORMATION IMPORTANTE
CHER CLIENT
Nous vous remercions d’avoir acheté cet appareil SHARP à écran LCD. An de garantir le bon fonctionnement de ce moniteur,
nous vous conseillons de lire attentivement cette brochure et de la conserver pour toute rĂŠfĂŠrence ultĂŠrieure.
INFORMATION IMPORTANTE .........................................1
CHER CLIENT ................................................................... 1
PRÉCAUTIONS DE SÉCURITÉ .......................................2
MESURES DE SÉCURITÉ ................................................4
PRÉCAUTIONS POUR LE MONTAGE .............................4
Composants fournis ........................................................5
PrĂŠparation de la tĂŠlĂŠcommande ...................................5
Connexions ......................................................................6
Mise sous tension et hors tension .................................7
CaractĂŠristiques ............................................................... 8
PrĂŠcautions pour le montage
(À l’attention des revendeurs et techniciens SHARP)
...8
Lisez les manuels se trouvant dans le CD-ROM fourni. (Adobe Reader est nĂŠcessaire pour pouvoir visualiser les manuels.)
Printed in China
ImprimĂŠ en Chine
Impreso en China
Gedruckt in China
Отпечатано в Китае
15E
TINS-G413WJZZ(1)
/