ROBEL 13.45SKS Vers. 01 Operating instructions
- Type
- Operating instructions
OPERATING MANUAL
13.45SKS Vers. 01
Rail Head Grinding Machine
Robel Bahnbaumaschinen
GmbH Industriestraße 31
83395 Freilassing
Telefon: ++49 (0) 86 54 609-
0 Fax: ++49 (0) 86 54 609-
Internet: www.robel.info
Translation of original operating manual
Status: 22.11.2017
Version 2
© 2017 Robel Bahnbaumaschinen GmbH
These operating instructions were produced in accordance with
the current state of technology at the time of printing.
The right to change on the basis of further developments is reserved.
Dimensions and weights are approximated.
Photographs show special layouts in some cases.
2
Content
Content
1.1
About these instructions ................................................
6
1.2
General Regulations.......................................................
6
1.3
Intended Audience for this Operating Manual...............
6
1.4
Liability Exclusions .........................................................
7
1.5
Copyright ........................................................................
7
1.6
Acceptance, Equipment and Operating Licence............
8
1.7
Validity of these instructions..........................................
8
2.
Safety......................................................................................................................................
9
2.1
Designated use...............................................................
9
2.2
Foreseeable misuse .......................................................
9
2.3
Conventions of layout.....................................................
9
2.4
Design changes, original parts.....................................
10
2.5
Protective devices ........................................................
10
2.6
Safety regulations ........................................................
10
2.7
Qualifications of staff ...................................................
11
2.8
Personal protective equipment....................................
11
2.9
Information on particular types of dangers .................
12
2.10
Accident prevention .....................................................
14
2.11
First Aid.........................................................................
15
2.12
Fire safety.....................................................................
15
3.
Technical data ......................................................................................................................
17
3.1
Drive..............................................................................
17
3.2
Grinding spindle ...........................................................
17
3.3
Dimensions...................................................................
17
3.4
Filling quantities...........................................................
17
3.5
Weight ..........................................................................
17
3.6
Abrasives ......................................................................
18
3.6.1 For rail head widths up to 75 mm ..................................
18
3.6.2 For rail head widths up to 120 mm................................
18
3.6.3 Cup wheel for frog noses (optional)................................
18
3.7
Plunging depth .............................................................
18
3.8
Digital tach/hour meter ...............................................
18
3.9
Noise emissions ...........................................................
19
3.10
Vibration .......................................................................
19
3.11
Environmental conditions ............................................
19
3.12
Structure gauge............................................................
20
3.12.1 Version with guiding handle on the left side .................
20
3.12.2 Version with guiding handle on the right side...............
21
4.
Description of machine ........................................................................................................
22
4.1
Structure.......................................................................
22
4.2
Overview of machine....................................................
23
3
Content
4.3
.............................................................Designvariants
24
4.3.1
Guide rollers .......................................................................
24
4.3.2
Diameter of abrasives ......................................................
25
4.3.3
Guiding handle...................................................................
26
4.4
Control elements ..........................................................
27
4.5
Accessory (to order)......................................................
28
4.6
Signs and Labels ..........................................................
30
4.6.1
Signs and Labels used......................................................
30
4.6.2
Position on the product ....................................................
33
4.7
Digital tach/hour meter ...............................................
34
4.8
Workplace ....................................................................
34
4.9
Structural gauge...........................................................
34
5.
Operating conditions ............................................................................................................
35
5.1
Operation......................................................................
35
5.2
Storage .........................................................................
35
5.3
Transport ......................................................................
36
6.
Commissioning.....................................................................................................................
37
6.1
Digital inductive tach/hour meter ...............................
37
6.1.1
Operation ............................................................................
37
6.1.2
Settings ...............................................................................
38
6.2
Re-railing ......................................................................
39
6.3
Adjusting the guiding handle .......................................
40
6.3.1 Variant with guiding handle on the right .......................
40
6.3.2 Variant with guiding handle on the left..........................
43
6.4
Fitting additional equipment........................................
44
6.4.1
Removing the carrying handles.......................................
44
6.4.2
Fitting additional equipment ...........................................
44
6.5
Mounting the guide rollers ...........................................
45
6.5.1
Removing the guide rollers..............................................
45
6.5.2
Fitting the guide rollers.....................................................
46
6.6
Adjusting the spacing of the guide rollers ...................
47
6.7
Adjusting the friction of the depth feed.......................
48
6.8
Checking the machine .................................................
49
6.8.1 Abrasive and grinding spindle .........................................
49
6.8.2
Motor ...................................................................................
50
6.9
Starting the engine.......................................................
55
6.9.1
Cold start.............................................................................
57
6.9.2
Warm start..........................................................................
59
6.10
Test run.........................................................................
60
6.11
Working with the machine...........................................
61
6.11.1 Grinding Vignole rails ........................................................
61
6.11.2 Grinding points...................................................................
61
6.12
Switching off the engine ..............................................
61
6.13
Retracting the grinding disc and increasing the friction
of the depth feed..........................................................
62
4
Content
6.14
..................................................Unrailingthemachine
63
7.
Maintenance.........................................................................................................................
64
7.1
Maintenance schedule .................................................
65
7.2
Engine...........................................................................
66
7.2.1
Checking the oil level........................................................
66
7.2.2
Changing the oil.................................................................
68
7.2.3
Maintaining the air filter...................................................
69
7.2.4 Maintaining the spark plug ..............................................
71
7.3
Lubrication....................................................................
74
7.4
Changing the abrasive..................................................
75
7.5
Tensioning the V-belt....................................................
76
7.5.1
Checking V-belt tension ....................................................
77
7.5.2
Adjusting V-belt tension....................................................
78
7.5.3
Replacing the V-belt ..........................................................
80
7.6
Cleaning and care ........................................................
80
8.
Troubleshooting....................................................................................................................
81
9.
Environmental protection and disposal ...............................................................................
82
9.1
Environmental protection.............................................
82
9.2
Disposal ........................................................................
82
10.
Appendix...............................................................................................................................
83
10.1
CE Declaration of Conformity.......................................
83
5
2. Safety
1. General Information
Staff operating and maintaining this product must have
read and understood these operating instructions.
All those involved must have access to the operating
instruc-tions at all times.
1.1 About these instructions
The following symbols are used to mark operating procedures,
lists and other elements of these instructions:
Symbol
Explanation
1.
Action
Operating procedure - the se-
2.
Action
quence of actions must not be
changed.
•
List 1
List- Sequence may be
– List 1.1
changed.
•
List 2
â–º Measure
Measure - the sequence must
â–º Measure
not be changed.
1.2 General Regulations
Appropriate legal requirements and accident prevention
measures for use of this product must generally be observed.
If they are not observed, the operator of the appliance takes
re-sponsibility for any legal consequences.
In the event of differences between prevailing regulations
that apply to use of the product and the manufacturer’s or
sub-contractor’s specifications, whichever limitations are the
most stringent must apply.
The buyer must provide all necessary machinery, equipment
and material resources for putting the delivered product into
operation and training staff. He must also make available un-
restricted, safe and sufficiently long track and work sections, on
which staff can learn how to operate and use the delivered
product and practise these tasks. Since the manufacturer or
supplier of the product has no influence over the buyer’s par-
ticular staffing and operating circumstances, no responsibility is
accepted for the effectiveness of the instructions.
ROBEL Bahnbaumaschinen GmbH together with its
customer service organizations are however happy to
provide further advice, training or other consultative services.
Further details and conditions can be obtained separately..
1.3 Intended Audience for this Operating Manual
This manual contains the information needed to use the
prod-uct they describe correctly.
The manual has been written exclusively for technically
quali-fied personnel. Qualified personnel in this context are:
6
2. Safety
•
Personnel who can prove that they are qualified to use
this product either through training or experience,
• Personnel familiar with the safety concepts that relate
to machinery and equipment,
• Maintenance and service personnel who are specially trained
to repair machines, appliances and its accessories.
Only persons who can read and understand this manual are
allowed to use the product. They should sign to indicate that
they have read and understood the manual.
Replacement, maintenance and operation of the product
should only occur where official regulations are strictly fol-
lowed for its use and safety, especially where they relate to
safety and protection of the workplace and environment as
well as the operating, maintenance and safety regulations or
other instructions supplied by the manufacturer or supplier.
1.4 Liability Exclusions
The manufacturer declares himself to be exempt from any
responsibility for damage arising when the product is not
used in a designated way. This also includes use of the
machine without safety mechanisms.
Any use of the product other than that specified above is not
designated and endangers the lives and health of operating
and maintenance personnel as well as the material property of
the operator. The manufacturer of the product declares
himself free from liability for damage to people or property
belonging to the operator or a third party if:
• the product is not used as specified,
• operating and maintenance personnel have not read and
understood the aforementioned directions and have used
the product for other purposes,
•
operating or maintenance personnel are not
sufficiently qualified
•
the product has been used under conditions
exceeding limiting values,
• the product has not been serviced within the time
speci-fied,
• the product has not been serviced using other than
original spare parts,
•
product components or attachments have been
altered without authorisation.
These exclusions from liability for damage to people or
materi-al property do not affect other exclusions.
1.5 Copyright
Specific characteristics and particular attributes of the product
are the intellectual property of ROBEL Bahnbaumaschinen GmbH.
The copyright on its use remains with ROBEL Bahnbaumaschinen
GmbH. It may not be reproduced either in full or in part,
published or otherwise exploited for competitive purposes,
whether for payment or not. Its contents may not be
7
2. Safety
passed by company employees to anyone outside the
busi-ness.
1.6 Acceptance, Equipment and Operating Licence
It is the buyer’s responsibility to check that the condition, fit-
tings, performance and especially the safety features of the
goods delivered match the relevant specifications agreed and to
take account of the regulations specified in the contract.
The buyer must equip the goods delivered with all fittings
nec-essary to meet relevant operational and safety
regulations, norms, statutory regulations or other regulations,
e.g. fire ex-tinguisher, first aid box, signal and
telecommunications equipment, additional warning devices,
protective clothing, safety notices etc.
Unless otherwise agreed, no fittings of this nature are
provided with the goods delivered.
Furthermore it is the buyer’s responsibility to demonstrate that
the goods delivered have been accredited for use by the ap-
propriate authority. Any documentation to be provided by the
manufacturer or supplier (descriptions, proof, attestations, etc.) to
enable this should be specified in the contract of supply.
Any additional measures and costs required to achieve
opera-tional accreditation must be borne by the buyer.
1.7 Validity of these instructions
These operating instructions apply to products with the
follow-ing EDP nos.:
• EDP no. XXXX
•
EDP no. XXXX
8
2. Safety
2. Safety
2.1 Designated use
The 13.45SKS rail head grinding machine is designed and
built for true-to-form grinding of weld joints, running surfaces,
rail shoulders and rail head side surfaces of Vignole steel rails
in manual operation without the use of cooling lubricant. It
may only be used for this purpose.
2.2 Foreseeable misuse
Currently there is no known misuse.
2.3 Conventions of layout
These instructions make use of the following warning texts and
symbols to keep the operator safe and injury-free and prevent
damage to the material assets of the operating company:
DANGER
Indicates that non-compliance with the in-
structions will result in death or severe (irre-
versible) injuries of the operating personnel.
WARNING
Indicates that non-compliance with the in-
structions may result in death or severe (irre-
versible) injuries of the operating personnel.
CAUTION
Indicates that non-compliance with the in-
structions may result in minor (reversible)
inju-ries of the operating personnel.
NOTICE
Points out that non-compliance with instructions may
result in damage to the product or other assets of the
operating company.
Contains important information about the
product, its operation or about a section of the
instructions on hand.
9
2. Safety
Structure of the warnings The warnings are structured as follows:
SIGNAL WORD
Type and source of danger!
(Possible) consequences when ignoring the
danger.
â–º Measure to avoid the danger.
2.4 Design changes, original parts
The manufacturer will not be liable if any unauthorised
chang-es to product components and attachments are made.
Original parts and accessories have been designed
specifically for this product. The use of non-approved spare
parts may re-sult in structural features of the product being
changed or im-paired.
The manufacturer is not liable for any damage which is
proven to be attributed to the use of such parts or inferior
operating fluids.
2.5 Protective devices
Danger to life for the operator and others from manipulation
of the safety devices!
â–º The operator is obliged to actually fit the designated pro-
tective devices during operation or to leave them in the
predetermined factory position.
â–º The person commissioned to carry out maintenance must
refit the protective devices after completing his work.
2.6 Safety regulations
The necessary requirements for protecting life, health, material
property and the environment when handling the product must
take precedence!
â–º Before using the product, make sure you can prove that all
personnel affected have been made aware of the following
relevant regulations and provisions:
• Statutory national safety regulations
• Provisions of the respective building code and works rules
•
Provisions of the respective professional and trade associa-
tions
•
Occupational and environmental health and safety regula-
tions
• Approvals regulations
• Company-internal regulations
•
All other applicable regulations, in addition to and in con-
cert with the manufacturer’s safety and operating regula-
tions
10
2. Safety
If necessary, the office in charge of operation must lay down
additional regulations and measures geared to the special
tasks of the product to ensure that all safety requirements are
met.
In addition to the information mentioned above the specific
safety regulations must be observed and adhered to.
2.7
Qualifications of staff
Operator
The operator was trained by the operating company in the
tasks assigned to him and informed of the potential dangers
arising from inappropriate behaviour.
Requirements for the
• Comprehensive training on the product
operator
• Knowledge of content of these operating and maintenance
instructions
• Knowledge of content of operating and maintenance
in-structions of suppliers’ and additional equipment
•
Knowledge of national regulations and laws concerning
the product and additional equipment
• Physical and mental fitness
• Power of concentration, sense of responsibility, reliability
• Necessary national requirements (qualifications,
minimum age)
• No influence of alcohol, medicines, drugs or fatigue, etc.
2.8 Personal protective equipment
The approved personal protective equipment has to be
used when operating and maintaining the product.
â–º Wear protective helmet.
â–º Wear protective gloves
â–º Wear ear protection
â–º Wear eye protection
â–º Wear appropriate, close-fitting clothing that cannot be
caught by rotating machine parts of saw blades
â–º Wear safety shoes with steel toe caps
â–º Wear breathing protection
The protective equipment is determined by:
•
These instructions
• National safety rules
• Rules of the professional trade associations
•
etc.
If there are differences between the prevailing regulations
within the operating company's scope of validity and those of
the manufacturer and his suppliers, whichever regulations
are the most stringent shall be applied.
11
2. Safety
2.9 Information on particular types of dangers
Danger from rotating parts
Danger from combustion en-
gines
Danger from fuel
Risk of clothing getting caught in and wound onto rotating
parts (grinding disk, socket etc.). Danger of contusions to
fin-gers and hands from rotating parts and abrasives.
â–º Wear suitable close-fitting clothing that cannot get caught
in rotating parts of the machinery or saw blades.
â–º Remove rings and neck chains or the like.
â–º Keep a safe distance from the abrasive when the engine is
running.
Danger of injuries, especially to the eyes, from flying
grinding dust and other objects that get caught.
â–º Safety glasses must be worn or the splinter shield moved
into place whenever the machine is running.
There is a risk of injury from rotating and hot
components when the engine is running.
â–º Only authorised technical personnel may work on the com-
bustion engine.
â–º Switch off the engine and allow it to cool down.
â–º Check the engine regularly and rectify any faults found
straight away (e.g. damage, leaks).
â–º Listen out for unusual noises or vibrations, etc.
â–º Perform maintenance work only with the engine switched
off.
â–º Watch out for hot components.
The ignition cable carries high voltage to the spark plugs. Le-
thal electric shocks may result if the ignition cable or spark
plug is touched when the engine is running. Wearers of
pace-makers are particularly at risk.
â–º Do not touch the ignition cable or spark plug when the en-
gine is running.
â–º Wearers of pacemakers must not carry out any work on the
ignition system.
Danger of poisoning from exhaust gases. The exhaust gases
contain carbon monoxide, a colourless, odourless toxic gas. If
breathed in, carbon monoxide can lead to severe brain
injuries or even death.
â–º Only operate combustion engines outdoors. Operate in
enclosed spaces only if exhaust fume extraction is in-stalled.
â–º Do not breathe in exhaust gases.
Fuel is highly flammable and under certain conditions fuel-
air mixtures can be explosive.
There is a danger of injury or damage to property if fuel is
not handled properly.
12
2. Safety
Danger from electrical
voltage
â–º Switch off the engine and allow it to cool down before
refill-ing, do not pour fuel over a hot engine or the exhaust.
â–º Refuel in a well-ventilated area with the engine stopped.
â–º Do not smoke when handling fuel.
â–º Keep fuel well away from naked flames and sparks.
â–º Avoid repeated or prolonged contact with skin or breathing
of vapor.
â–º Be careful not to spill fuel when refuelling
â–º Refill fuel only with suitable filling devices (e.g. funnel).
â–º Wipe up spills immediately.
â–º Ensure any spilled fuel has fully evaporated before starting
the engine.
â–º After refuelling, make sure the tank cap is closed properly
and securely.
â–º Before starting the machine, move it at least 3 m away
from the refuelling point.
â–º Under no circumstances start the machine if:
•
Fuel has been spilled onto it. In this case wipe up all
traces of fuel.
• Fuel has been spilled onto the user or the user’s clothing.
In this case the user must change their clothing.
â–º Fuel leaks. Regularly check the tank cap and fuel lines for
leakages.
â–º Keep fuel out of reach of children.
If the fuel tank is overfilled, heat subsequently generated may
cause the fuel to expand and emerge through openings in the
filler cap.
â–º Do not overfill the tank so that fuel rises up into the filler
neck.
Some parts may be live and may cause severe to fatal
injuries when getting in contact with them.
â–º Work on the electrical system only by authorised electrical
engineers.
â–º Rectify faults (contact faults, external damage to cables or
housings, etc.) straight away.
â–º Before working on the electrical system: Shut off the power
supply to the system, switch off the drive and disconnect the
power supply.
â–º During work on the electrical system: Do not touch any live
lines.
â–º Check earthing cables are securely seated and complete.
â–º Check that the connecting surfaces of the earthing cables
are clean and free from corrosion.
Danger from noise
13
2. Safety
Danger from heat
Danger of fire
Danger from vibration
Risk of environmental damage
Danger arising from
unauthorised start-up
2.10 Accident prevention
14
Permanent damage, especially to hearing, if the operator
does not constantly wear personal hearing protection.
â–º Wear ear protection.
Risk of injury from touching hot parts.
â–º Do not touch heated parts.
â–º Prior to work on heated parts, switch off engines and allow
hot parts to cool down for at least 30 minutes.
â–º Set the machine down at least one metre away from build-
ings and other equipment.
â–º Make sure there is no flammable material near the engine
and that no objects are placed onto the running engine.
â–º Cover and/or offload the machine only after it has cooled
down.
The transmission of vibrations to the human body causes
ad-verse health effects. Although the operating guide handle
is vibration cushioned, a complete decoupling of vibrations
is unachievable.
â–º Wear padded gloves.
â–º During the work process, incorporate vibration-free activi-
ties that place mainly dynamic demands on muscles.
The majority of the components and parts used are subject
to special regulations for collection and disposal.
â–º Dispose of components according to material groups (steel,
plastics, oils, etc.).
â–º Collect waste oil in line with the relevant regulations and
dispose of it accordingly.
Unauthorised start-up and misuse can result in dangers
and damage of any kind.
â–º Unauthorised start-up by unauthorised persons is strictly
prohibited.
â–º It is up to the operating company to assess this risk.
â–º It is the responsibility of the operating company to imple-
ment appropriate measures against unauthorised start-up.
The accident prevention regulations of the Civil Engineering
association also find application in these operating
instructions and are to be carefully read and adhered to.
â–º Always observe the general and internal accident preven-
tion regulations.
â–º Consider the potential risks of accidents in association with
the special tasks of the product and provide for appropriate
training.
2. Safety
â–º Check that the product is in proper working order before
putting it into service:
• Equipment, devices, tools, accessories, safety equipment,
etc. are complete and intact.
• Inspection and maintenance work has been carried
out professionally and on schedule.
• Operating fluids have been topped up (fuel, lubricants, etc.)
•
All prerequisites for carrying out work safely have been
met with regard to you and other persons, material
property and the environment.
â–º Beware of the particular dangers of the product and your
work area, especially:
• persons and obstacles,
•
adherence to safety clearances,
•
traffic on adjacent tracks,
•
secure fitting of all protective equipment,
•
compliance with all operationally necessary
safety measures.
â–º Leaking operating fluids (oil, grease, etc.) must be removed
immediately to prevent a fire hazard or risk of slipping. Keep
suitable oil binding agents and cleaning agents at hand.
â–º Before leaving the product perform the following checks:
• It has been shut down properly.
•
It is secured against moving unintentionally.
• Tools and accessories are stowed away safely.
â–º Use only machines, appliances and tools that work proper-
ly.
â–º Rectify smaller faults straight away in order to avoid larger
faults.
2.11 First Aid
Ensure the following to be able to provide First Aid in an
emer-gency:
â–º Make sure that the First Aid kit is in proper condition, com-
plete and clean at all times.
â–º Consult the medical service or doctor at your office regard-
ing First Aid measures and appropriate equipment.
â–º Immediately replenish used up material.
â–º Store First Aid equipment (First Aid kit, blankets etc.) and
fire extinguishers within easy reach.
â–º Carry material for securing accident sites.
2.12 Fire safety
Toxic fumes are released when fuels, oils, paints or
varnishes catch fire.
15
2. Safety
In addition, all measures required to prevent the development or
spreading of a fire must be taken in individual cases.
With smoldering fires in electrical equipment toxic vapours
are released from charring cables, also with fires of fuels, oil
or paints.
â–º Everybody is obliged, as far as possible and reasonable to
refrain from any actions that may cause a fire or favour the
spreading of a fire. In addition, all measures required to
prevent the development or spreading of a fire must be
taken in individual cases.
â–º In general, any fires that occur are to be fought only with
powder extinguishers.
General The following fire safety measures must be adhered to.
â–º Use only approved fire extinguishers (powder-type extin-
guishers) of the prescribed fire protection class.
â–º Check the fire extinguishers periodically and ensure that
they are provided with an inspection label (at least every 2
years, check the expiry date!).
â–º After using a fire extinguisher, replace it straight away.
16
3. Technical data
3. Technical data
3.1 Drive
Type: Robel 190, air-cooled, single cylinder four-stroke engine
Speed
4,200 1/min
Output at 4,300 1/min
5.0 kW
Fuel
Regular petrol,
min. 91 RON
(corresponds to
86 octane)
Consumption
approx. 1.7 l/h
Exhaust emissions
Corresponds to
Euro II
3.2
Grinding spindle
Maximum speed of output shaft
4,500 1/min
Mounting diameter for abrasive
30 mm
Fastening thread
M20
3.3
Dimensions
Length
1,336 mm
Width
530 mm
Height
830 mm
Distance between rollers
1,000 mm
3.4
Filling quantities
Fuel
4 l
Engine: Engine oil SAE 15W-40
approx. 0.6 l
3.5
Weight
Standard version with monorail chassis with
59.5 kg
empty fuel tank
17
3. Technical data
3.6
Abrasives
Grinding discs of bonded abrasive.
3.6.1 For rail head widths up to 75 mm
Outer diameter
125 mm
Inner diameter
56 mm
Height
65 mm
Maximum permissible speed
7,640 U/min
3.6.2 For rail head widths up to 120 mm
These abrasive discs must be ordered separately.
Cup wheel
Outer diameter
150 mm
Inner diameter
55 mm
Height
60 mm
Maximum permissible speed
6,350 U/min
3.6.3 Cup wheel for frog noses (optional)
These abrasive discs must be ordered separately.
Cup wheel
Outer diameter
90 mm
Inner diameter
55 mm
Height
65 mm
Maximum permissible speed
10,600 U/min
3.7 Plunging depth
The plunging depth is controlled steplessly.
Plunging depth of the grinding spindle
0 - 70 mm
3.8 Digital tach/hour meter
Range
Value
Range
Revolutions per minute (RPM)
0…60,000 RPM
Max. value of revolutions per minute
0…60,000 RPM
ever reached (RPM)
Operating hours
00…99,999 hours
Resolution
Value
Resolution
Revolutions per minute (RPM)
1 RPM
Max. value of revolutions per minute
1 RPM
ever reached (RPM)
Operating hours
0.1 hour
Battery life: 5 years (standard use)
Watertight IP68
18
3. Technical data
3.9 Noise emissions
Emission measurements as
of 22.10.10:
3.10 Vibration
The workplace emission values during operation depend on the
tool used (abrasive) and the method of operation (e.g. pressure
and feed rate). The stated values may therefore also vary.
Since the noise level criterion for personnel is exceeded
when working, suitable ear protection must be worn (see
also na-tional statutory regulations as well as basic health
and safety requirements).
Sound pressure level
Sound pressure level
LA,eq
LC,peak
Grinding
103,8 dB
110,2 dB
Vibration according to ‘Hand-
Frequency-weighted vibration acceleration
Arm Vibrations’ test report
in m/s
2
dated 13.12.10:
Vector sum
6.5 m/s
2
Assessment of the noise level for personnel
requires consideration of the actual working
environment for each worker (e.g. staying at
different places/machines)
3.11 Environmental conditions
Temperature range
Operation
-20°C to 70°C
Transport
-20°C to 70°C
Storage
-20°C to 70°C
19
3. Technical data
3.12 Structure gauge
3.12.1 Version with guiding handle on the left side
Fig. 1: Structural gauge, Version with guiding handle on the left side, Grinding of rail head and rail head
side surface on land side
Fig. 2: Structural gauge, Version with guiding handle on the left side, Grinding of rail head and rail head
side surface on track side
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
ROBEL 13.45SKS Vers. 01 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Pro-Line Boats 2007 25 Super Sport Owner's manual
-
-
-
-
Forest-Master MLR52 User manual
-
-
-
-
-
