CyberData 011244 is a versatile network endpoint device that offers a range of features and capabilities to enhance your communication system. Here's a brief overview of its key functions:
Features:
- Singlewire Strobe: The device incorporates a strobe light that can be triggered remotely, providing visual alerts for various scenarios.
- PoE Compatibility: It supports Power over Ethernet (PoE), allowing for easy installation and power supply without the need for separate wiring.
- IP Addressing: The device can obtain its IP address automatically through DHCP or be manually configured for specific network requirements.
CyberData 011244 is a versatile network endpoint device that offers a range of features and capabilities to enhance your communication system. Here's a brief overview of its key functions:
Features:
- Singlewire Strobe: The device incorporates a strobe light that can be triggered remotely, providing visual alerts for various scenarios.
- PoE Compatibility: It supports Power over Ethernet (PoE), allowing for easy installation and power supply without the need for separate wiring.
- IP Addressing: The device can obtain its IP address automatically through DHCP or be manually configured for specific network requirements.
Quick Reference 930642C © 2015, CyberData Corporation, ALL RIGHTS RESERVED© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930642C Quick Reference
Typical System Installation
Getting Started
• Download the V3 Singlewire Strobe Operations Guide PDF file, from the V3 Singlewire Strobe product page at:
http://www.cyberdata.net/products/voip/digitalanalog/strobev3singlewire/docs.html
• Create a plan for the locations of your V3 Strobes.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: The device enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Address
a
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Mask
a
255.0.0.0
Default Gateway
a
10.0.0.1
a. Default if there is not a DHCP server present.
Singlewire StrobeSinglewire StrobeSinglewire Strobe
IP Phone
IP PBX Server
Generic PoE Switch
12 34 56
(1) V3 Strobe Assembly
(4) #6 x 1.5 inches
Sheet Metal Screw
(1) Gang Box Mounting Kit
(4) #6 Ribbed Plastic
Anchor
(4) #6-32 x 0.625-inch
Flat-Head Machine Screw
(1) Wall Mounting Kit
The IP Endpoint Company
Installation Quick Reference
V3 Singlewire Strobe
011244
Wall Mounting Options
Gang Box Mounting Options
Contacting CyberData
Backplate
Wall
(Not Provided)
Network Cable &
Screw
121001A
Accessory Kit
(4 Places) on Wall
Pre Drill Holes
Ground Wire
Cutout
for Ground Wire Connection
Pick One of Four Mounting Hole
Slot
Entry
Cable
Closed
Slots
Cable
Mounting
Screw (3x)
Single Gang Box use two
Wall Cutout
or Two Gang Box
Backplate accept
Single Gang Box
Two Gang Box use Four
Backplate
Wall Cutout
Screw
121002B
Accessory Kit
(Not Provided)
Network Cable & Ground Wire
Available Mounting Hole
Pick One of Two or Four
for Ground Wire Connection
Mounting
Screw (3x)
Slot
Entry
Cable
Closed
Slot
Cable
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
www.CyberData.net
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930642C Quick Reference Quick Reference 930642C © 2015, CyberData Corporation, ALL RIGHTS RESERVED
Connections
RTFM Button
Terminal Block
Wire (IN)
Terminal Block
can accept
16 AWG wire
Alternate Power Input:
1 = +12 to 24 VDC at 1000mA (500 mA minimum)*
2 = Power Ground*
Relay Contact:
(1A at 30 VDC for Continuous Loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
3
4
Contacts 1 & 2 on the J3 Terminal Block are only for
powering the device from a non-PoE +12VDC power
source as an alternative to NetworkPoE power. Use of
these contacts for any other purpose will damage the
*
J3
device and void the product warranty.
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
*Contacts 1 and 2 on the J3 terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
3
4
SW1
When the device is operational and linked to a
network, you can use the Reset Test Function
Management (RTFM) button (SW1) to
announce the device’s IP address or restore
the device to the factory default settings.
To restore the device to factory default
settings:
• Press and hold the RTFM switch for
seven seconds, and then release the
RTFM switch.
Dimensions
Maximum Recommended Wall Cutout Dimensions
2.1 [55]
4.5 [115]
DIMENSIONS ARE IN INCHES [MILLIMETERS]
4.5 [115]
Dimensions are in Inches [Millimeter]
Wall Cutout
0.25 [6.4]
0.25 [6.4]
0.25 [6.4]
0.25 [6.4]
-
1
-
2
CyberData 011244 is a versatile network endpoint device that offers a range of features and capabilities to enhance your communication system. Here's a brief overview of its key functions:
Features:
- Singlewire Strobe: The device incorporates a strobe light that can be triggered remotely, providing visual alerts for various scenarios.
- PoE Compatibility: It supports Power over Ethernet (PoE), allowing for easy installation and power supply without the need for separate wiring.
- IP Addressing: The device can obtain its IP address automatically through DHCP or be manually configured for specific network requirements.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CyberData 011244 Owner's manual
-
-
-
CyberData 011087 Owner's manual
-
-
CyberData 011305 Reference guide
-
-
-
CyberData 011307 Owner's manual
-