King Canada SS-5015C User manual

Brand: King Canada

Model: SS-5015C

Type: User manual

INSTRUCTION MANUAL

MODEL: SS-5015C

FOLDING STAND FOR

10” WORKSITE TABLE SAW

Folding stand designed for use

with our 10” Portable Worksite

Table Saw model KC-5015C.

Can also be used with Bosch

10” Portable Jobsite Table Saw

model GTS1031

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR FOLDING STAND

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

INTENDED FOR COMMERCIAL USE

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purchase to an

authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if

any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

KING CANADA INC. DORVAL, qUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

ASSEMBLY & INSTALLING

WORKSITE TABLE SAW ON STAND

WARNING! IF ANY PART IS MISSING OR DAMAGED, DO NOT USE THIS

STAND UNTIL YOU HAVE REPLACED THE MISSING OR DAMAGED PART. For

your safety, complete the assembly of the stand before attempting to install Work-

site Table Saw on stand.

INSTALLING THE 4 LEGS

1. The stand comes without the 4 legs (A) Fig.1 installed. They will need to be

assembled to the stand frame. Slide each leg (A) into the stand as shown in

Fig.1.

2. Secure each leg to the stand frame using two hex. bolts and hex. nuts (B) Fig.1.

INSTALLING KING CANADA 10” WORKSITE TABLE SAW (KC-5015C)

1. Unfold the stand and position it on a level surface as shown in Fig.1.

NOTE: Refer to the two fixing brackets (C) Fig.1, they indicate the front of the

stand.

2. Loosen the two cap screws (A) Fig.2 screwed into the two fixing brackets (B).

3. Position yourself at the rear of the stand, lift Worksite Table Saw (KC-5015C)

and place it onto the stand. Slide the front bar of the saw frame (C) Fig.2 into

the two fixing brackets (B). Lower Worksite Table Saw onto stand.

4. Make sure the rear bar of the frame is positioned in front of the two support

plates (A) Fig.3 as shown.

5. Pivot the retaining bracket (B) Fig.3 over the rear bar of the frame as shown,

then secure retaining bracket with rear clip (C).

6. Once the Worksite Table Saw is secured on the stand, tighten the two cap

screws (A) Fig.2 against the front bar.

NOTE: If you have purchased this folding stand to install your Bosch

Table Saw

(GTS1031), the above assembly instructions apply in the same way.

FIGURE 1

FIGURE 2

FIGURE 3

King Canada SS-5015C User manual

King Canada SS-5015C User manual

King Canada SS-5015C User manual

Related papers

Other documents