ENGLISH ESPAÑOL
FRANÇAIS
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury .
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
31WG
For Occasional Use Only
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright
E
2002 Electrolux Home Products, Inc.
530088154
4/24/02
R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater .com
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
2
UL CLASSIFIED PRODUCT NOTICE
Only the following Gasoline Powered Combination Gardening Appliance powerhead models
and their respective attachments have been Classified by Underwriters Laboratories, Inc., in
accordance with the applicable safety requirements.
Powerhead including trimmer attachment
31WG..........................
Optional blower attachment
3000B........................................
Optional brushcutter attachment
4000C..................................
The following attachment is Listed by Underwriter’s Laboratories, Inc., in accordance with
UL Standard 1602, “Gasoline--Engine--Powered, Rigid--Cutting Member, Edgers and Edge--
Trimmers.”
Optional edger attachment
1000E........................................
SAFETY RULES
WARNING:
When using gardening
appliances, basic safety precautions must al-
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instruc-
tions.
This power unit can be dangerous!
Operator is
responsible for following instructions and warn-
ings on unit and in manual. Read entire instruc-
tion manual before using unit! Be thoroughly fa-
miliar with the controls and the proper use of the
unit. Restrict the use of this unit to persons who
have read, understand, and will follow the
instructions and warnings on the unit and in the
manual. Never allow children to operate this
unit.
SAFETY INFORMATION
ON THE UNIT
INSTRUCTION
MANUAL
DANGER:
Never use blades with line
trimmer attachment. Never use flailing de-
vices with any attachment. This unit (when
used with supplied line trimmer attachment) is
designed for line trimmer use only. Use of any
other accessories with line trimmer attach-
ment will increase the risk of injury.
WARNING:
Trimmer line throw s ob-
jects violently. You and others can be blinded/in-
jured. Wear eye and leg protection. Keep body
parts clear of rotating line.
Eye Protection
Boots
Hazard Zone
50 ft.
(15 m)
Keep children, bystanders, and animals 50 feet
(15 meters) away. Stop unit immediately if ap-
proached.
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, contact your authorized
service dealer or call 1-800-554- 6723.
OPERATOR SAFETY
S
Dress properly. Always wear safety
glasses or similar eye protection when op-
erating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should be marked Z87.
S
Always wear face or dust mask if operation
is dusty.
S
Always wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
S
Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
S
Secure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
S
Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
S
Stay Alert. Do not operate this unit when
you are tired, ill, upset or under the influ-
ence of alcohol, drugs, or medication.
Watch what you are doing; use common
sense.
S
Wear hearing protection.
S
Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S
Keep handles free of oil and fuel.
S
Always keep engine on the right hand side
of your body.
S
Hold the unit firmly with both hands.
S
Keep trimmer head (or other optional at-
tachment) below waist level and away from
all parts of your body. Do not raise engine
above your waist.
S
Keep all parts of your body away from muf-
fler and spinning line (or other optional at-
tachment). Keep engine below waist level.
A hot muffler can cause serious burns.
S
Keep firm footing and balance. Do not over-
reach or use from unstable surfaces such
as ladders, trees, steep slopes, rooftops,
etc.
S
Use only in daylight or good artificial light.
S
Use only for jobs explained in this manual
(or manuals for optional attachments).
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
3
UNIT / MAINTENANCE SAFETY
S
Disconnect the spark plug before perform-
ing maintenance except carburetor adjust-
ments.
S
Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep in good working
condition.
S
Replace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
S
Maintain unit according to recommended
procedures. Keep cutting line at proper
length.
S
Use only 0.080
!
(2 mm) diameter Weed
Eater
"
brand line. Never use wire, rope,
string, etc.
S
Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and se-
curely fastened.
S
Make sure unit is assembled correctly as
shown in this manual.
S
Make carburetor adjustments with lower
end supported to prevent line from contact-
ing any object.
S
Keep others away when making carburetor
adjustments.
S
Use only recommended Weed Eater
"
ac-
cessories and replacement parts.
S
Have all maintenance and service not ex-
plained in this manual performed by an au-
thorized service dealer.
FUEL SAFETY
S
Mix and pour fuel outdoors.
S
Keep away from sparks or flames.
S
Use a container approved for fuel.
S
Do not smoke or allow smoking near fuel or
the unit.
S
Avoid spilling fuel or oil. Wipe up all fuel
spills.
S
Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S
Stop engine and allow to cool before re-
moving fuel cap.
S
Always store gasoline in a container ap-
proved for flammable liquids.
TRANSPORTING AND STORAGE
S
Allow engine to cool before storing or trans-
porting in vehicle.
S
Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
S
Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S
Store unit so line limiter blade cannot acci-
dentally cause injury. The unit can be hung
by the tube.
S
Store unit out of reach of children.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-- vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
LINE TRIMMER SAFETY
WARNING:
Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S
Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
S
Cut from your right to your left. Cutting on
left side of the shield will throw debris away
from the operator.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
WARNING:
For each optional at-
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
WARNING:
Ensure handlebar is
installed when using edger or brushcutter at-
tachments. Attach handlebar above arrow on
safety label on the upper tube (engine end of
unit). If your edger or brushcutter attachment
does not include a handlebar, a handlebar ac-
cessory kit (#530071451) is available from
your authorized service dealer.
Handlebar
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
4
EDGER SAFETY
WARNING:
Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
S
Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
S
Allow blade to stop before removing it from
the cut.
S
Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way . Replace parts that are cracked,
chipped, or damaged before using the unit.
S
Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
S
Always keep the wheel and depth adjusting
skid in contact with the ground.
S
Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
S
Always use the handlebar when using edg-
er attachment.
BLOWER/VACUUM SAFETY
WARNING:
Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S
Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc., could be picked up by the air intake
and thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
S
Never place objects inside the blower
tubes, vacuum tubes or blower outlet. Al-
ways direct the blowing debris away from
people, animals, glass, and solid objects
such as trees, automobiles, walls, etc. The
force of air can cause rocks, dirt, or sticks to
be thrown or to ricochet which can hurt
people or animals, break glass, or cause
other damage.
S
Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tubes.
S
Check air intake opening, blower tubes or
vacuum tubes frequently, always with en-
gine stopped and spark plug disconnected.
Keep vents and discharge tubes free of de-
bris which can accumulate and restrict
proper air flow.
S
Never place any object in air intake opening
as this could restrict proper air flow and
cause damage to the unit.
S
Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
S
To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
BRUSHCUTTER SAFETY
DANGER:
Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
WARNING:
Do not use trimmer head
as a fastening device for the blade.
WARNING:
The blade continues to
spin after the throttle is released or engine is
turned off. The coasting blade can throw ob-
jects or seriously cut you if accidentally
touched. Stop the blade by contacting the
right hand side of the coasting blade with ma-
terial already cut.
Stop coasting
blade by contact
with cut material.
WARNING:
Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
S
Throw away and replace blades that are
bent, warped, cracked, broken or damaged
in any other way.
S
Install required shield properly before using
the unit. Use the metal shield for all metal
blade use.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
5
WARNING:
Only use brushcutter at-
tachments that provide a metal shield with
proboscis nose.
Proboscis
nose
S
Use only specified blade and make sure it is
properly installed and securely fastened.
S
Cut from your left to your right. Cutting on
the right side of the shield will throw debris
away from the operator.
S
Always use the handlebar and a properly
adjusted shoulder strap with blade (see AS-
SEMBLY instructions in brushcutter attach-
ment instruction manual).
CULTIVATOR SAFETY
WARNING:
Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark
plug before unclogging tines or making re-
pairs.
WARNING:
Inspect the area to be
cultivated before starting the unit. Remove all
debris and hard and sharp objects such as
rocks, vines, branch-- es, rope, string, etc.
S
Avoid heavy contact with solid objects that
might stop the tines. If heavy contact oc-
curs, stop the engine and inspect the unit
for damage.
S
Never operate the cultivator without the tine
cover in place and properly secured.
S
Keep the tines and guard clear of debris.
S
After striking a foreign object, stop the en-
gine, disconnect the spark plug and inspect
the cultivator for damage. Repair before re-
starting.
S
Disconnect attachment from the drive en-
gine before cleaning the tines with a hose
and water to remove any build--up. Oil the
tines to prevent rust.
S
Always wear gloves when servicing or
cleaning the tines. The tines become very
sharp from use.
S
Do not run unit at high speed unless culti-
vating.
HEDGE TRIMMER SAFETY
DANGER:
RISK OF CUT; KEEP
HANDS AWAY FROM BLADE -- Blade
moves momentarily after the trigger is re-
leased. Do not attempt to clear away cut ma-
terial when the blade is in motion. Make sure
the switch is in the OFF position, the spark
plug wire is disconnected, and the blade has
stopped moving before removing jammed
material from the cutting blade. Do not grab or
hold the unit by the cutting blade.
Allow blades to stop
before removing
them from the cut.
Blades move
momentarily
after the
trigger is
released.
WARNING:
Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S
Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in
any other way . Have worn or damaged
parts replaced by your authorized service
dealer.
S
Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S
Keep the cutting blade and air vents clear of
debris.
POLE PRUNER SAFETY
WARNING:
Reciprocating blade can
cause severe injury. Inspect the unit before
use. Do not operate unit with a bent, cracked
or dull blade. Keep away from the blade.
WARNING:
The reciprocating blade
is sharp. Do not touch. To prevent serious in-
jury, always stop engine and ensure blades
have stopped moving, disconnect spark plug,
and wear gloves when changing or handling
the blade.
WARNING:
A coasting blade can
cause injury while it continues to move after
the engine is stopped. Maintain proper con-
trol of the unit until the blade has completely
stopped moving. Keep hands, face and feet
at a distance from all moving parts. Do not at-
tempt to touch or stop the blade when it is
moving.
WARNING:
Falling objects can
cause severe head injury. Wear head protec-
tion when operating this unit with a pole prun-
er attachment.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
6
WARNING:
To prevent serious inju-
ry, do not use more than one boom extension
with a pole pruner attachment.
WARNING:
Keep the pruner away
from power lines or electrical wires.
S
Only use for pruning limbs or branches up
to 4 inches in diameter.
S
Do not operate the unit faster than the
speed needed to prune. Do not run the unit
at high speed when not pruning.
S
Always stop the unit when work is delayed
or when walking from one cutting location to
another.
S
If you strike or become entangled with a for-
eign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations. Dis-
card blades that are bent, warped, cracked
or broken.
S
Stop the unit immediately if you feel exces-
sive vibration. Vibration is a sign of trouble.
Inspect thoroughly for loose nuts, bolts or
damage before continuing. Contact an au-
thorized service dealer for repair or re-
placement of affected parts as necessary.
SNOW THROWER SAFETY
WARNING:
Keep hands and feet
away from the rotor when starting or running
the engine. Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.
WARNING:
Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
WARNING:
Inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
S
Direct material discharge away from glass
enclosures, automobiles, etc.
S
Do not run engine at high speed while not
removing snow.
S
Be attentive when using the snowthrower,
and stay alert for holes in the terrain and
other hidden hazards.
S
Make sure the rotor will spin freely before
attaching the snowthrower to the power-
head.
S
If the rotor will not rotate freely due to frozen
ice, thaw the unit before thoroughly before
attempting to operate under power.
S
Keep the rotor clear of debris.
S
Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
S
After striking a foreign object, stop the en-
gine, disconnect spark plug and inspect the
snowthrower for damage and repair if nec-
essary before restarting unit.
S
Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S
Never attempt to use the snowthrower on a
roof.
S
Never operate the snowthrower near win-
dow wells, dropoffs, etc.
S
Never discharge snow onto public roads or
near moving traffic.
S
Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow
from steep slopes.
S
Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S
Look behind and use care when backing
up. Exercise caution to avoid slipping or fal-
ling, especially when operating in reverse.
S
Know how to stop quickly.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
7
ASSEMBLY
WARNING:
If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE:
If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
INSTALLING TRIMMER ATTACH-
MENT
CAUTION:
When inst alling trimmer attach-
ment, place the unit on a flat surface for stabil-
ity.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
Knob
LOOSEN
TIGHTEN
2. Remove the tube cap from the trimmer at-
tachment (if present).
3. Position locking/release button of attach-
ment into guide recess of coupler.
4. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
5. Before using the unit, tighten the knob se-
curely by turning clockwise.
Coupler Primary Hole
Upper
Tube
Locking/
Release
Button
Lower
Attachment
Guide Recess
WARNING:
Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole.
For optional attachments, see the AS-
SEMBLY section of the applicable attach-
ment instruction manual.
ATTACHING SHIELD
WARNING:
The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you. For proper
orientation of shield, see KNOW YOUR TRIM-
MER illustra tion in OPERATION sec tion .
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole
in bracket.
4. Securely tighten wing nut onto bolt.
Slot
Shield
Wing
Nut
Bracket
ADJUSTING THE HANDLE
WARNING:
When adjusting the han-
dle, be sure it remains between the trigger
and the arrow on the safety label.
1. Loosen wing nut on handle.
2. Rotate the handle on the tube to an up-
right position; retighten wing nut.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
8
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustratio n s with your unit to fam ilia rize yourse lf with the location of the variou s controls
and adjustments. Save this manual for future reference.
Line Limiter
Blade
Primer Bulb
Assist Handle
Starter
Handle
Throttle Trigger
Choke
Lever
Shield
Trimmer
Head
Tube
Muffler
ON/OFF Switch
Coupler
ON/OFF SWITCH
The ON/OFF switch is located on the trigger
handle and is used to stop the engine. Move the
switch to the OFF position to stop the engine.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHO KE
position. After the engine attempts to start, move
the choke lever to the HALF CHO KE position.
Once engine has started, move the choke lever
to the OFF CHO KE position.
COUPLER
The COUPLER enables optional attach-
ments to be installed on the unit.
BEFORE STARTING ENGINE
WARNING:
Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING:
Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. Mix
gasoline and oil at a ratio of 40:1. A 40:1 ratio
is obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline. DO NOT USE
automotive oil or boat oil. These oils will cause
engine damage. When mixing fuel, follow
instructions printed on container.
Once oil is added to gasoline, shake
container momentarily to assure that the fuel
is thoroughly mixed. Always read and follow
the safety rules relating to fuel before fueling
your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage.
To avoid engine problems, empty the fuel sys-
tem before storage for 30 days or longer.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty. Use fresh fuel next season.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage
may occur.
See the STORAGE section for additional in-
formation.
HOW TO STOP YOUR UNIT
S
To stop the engine, move the ON/OFF
switch to the OFF position.
S
If engine does not stop, move choke lever
to FULL CHOKE position.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
9
ON/OFF Switch
HOW TO START YOUR UNIT
WARNING:
The trimmer head will
turn while starting the engine.
Avoid any contact with the muffler. A hot muf-
fler can cause serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Starting Position
Muffler
Choke
Lever
Starter Handle
Primer Bulb
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON position.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to FULL CHOKE by
aligning lever with position shown on de-
cal (see illustration below).
Choke
position
decal
5. Squeeze the throttle trigger fully and hold
through
all remaining steps.
6. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
7. As soon as engine sounds as if it is trying
to start, move choke lever to HALF
CHOKE by aligning lever with position
shown on decal (see illustration below).
Choke
position
decal
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn’t start after 6 pulls (at the HALF
CH OKE position), move the choke lever to
the FULL CH O KE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more time s . Mo v e the ch o k e lev e r to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. If the engine doesn’t start, r epeat
procedure 2 additional times.
NOTE:
If engine still doesn’t start, it is
probably flooded. Proceed to STARTIN G A
FLOODED ENGINE.
9. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
OFF CHOKE by aligning lever with posi-
tion s hown on decal (see illustration be-
low). Allow the unit to run for 30 more se-
conds at OFF CHOKE before releasing
the throttle trigger.
NOTE:
If engine dies with the choke le-
ver in the OFF CHOKE position, move
the choke lever to the HALF CHOKE
position and pull the rope until engine
runs, but no more than 6 pulls.
Choke
position
decal
STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 15 seconds, then
move the choke lever to the OFF CHOKE
position.
NOTE:
If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
10
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger
1000E.......................
Cultivator
2000T...................
Blower
3000B......................
Brushcutter
4000C.................
WARNING:
Always stop unit and dis-
connect spark plug before removing or instal-
ling attachments.
REMOVING TRIMMER ATTACH-
MENT (OR OTHER OPTIONAL AT-
TACHMENTS)
CAUTION:
When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
Knob
LOOSEN
TIGHTEN
Upper Tube
Lower
Attachment
2. Press and hold the locking/release button.
Locking/Release
Button
Coupler
Upper Tube
Lower Attachment
3. While securely holding the engine and
upper tube, pull the attachment straight
out of the coupler.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the tube cap from the attach-
ment (if present).
2. Position locking/release button of attach-
ment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
4. Before using the unit, tighten the knob se-
curely by turning clockwise.
Coupler
Primary Hole
Upper
Tube
Locking/
Release
Button
Attachment
Guide Recess
WARNING:
Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit.
OPERATING POSITION
Eye Protection
Long Pants
Heavy Shoes
ALWAYS WEAR:
Cut from your right to your left.
WARNING:
Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise
and vibration. The cutting line will last longer
and will be less likely to “weld” onto the spool.
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
S
Release the throttle trigger.
S
Move the ON/OFF switch to the OFF posi-
tion.
TRIMMER LINE ADVANCE
The cutting head advances line automati-
cally. Do not tap head on the ground to ad-
vance line.
This may break parts and cause
cutting head to malfunction.
Upon unit start up, the line will advance auto-
matically to the correct cutting path length.
Always keep the shield in place when the tool
is being operated.
WARNING:
Use only .080” (2 mm)
diameter round line.
Other sizes and
shapes of line will not advance properly and
will result in improper cutting head function or
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
11
can cause serious injury. Do not use other
materials such as wire, string, rope, etc. Wire
can break off during cutting and become a
dangerous missile that can cause serious in-
jury.
CUTTING METHODS
Use minimum speed and do not crowd the line
when cutting around hard objects (rock,
gravel, fence posts, etc.), which can damage
the trimmer head, become entangled in the
line, or be thrown causing a serious hazard.
S
The tip of the line does the cutting. You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area. The right and wrong
ways are shown below.
Tip of the Line
Does The Cutting
Right
Line Crowded Into
Work Area
Wrong
S
The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S
For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S
During light duty cutting.
S
Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S
For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING
-- Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
Trimming
3in.(8cm)
Above Ground
SCALPING
-- The scalping technique re-
moves unwanted vegetation. Hold the bottom
of the trimmer head about 3 in. (8 cm) above
the ground and at an angle. Allow the tip of the
line to strike the ground around trees, posts,
monuments, etc. This technique increases
line wear.
Scalping
MOWING
-- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Mowing
SWEEPING
-- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
Sweeping
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
12
MAINTENANCE
WARNING:
Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
CHECK FOR LOOSE
FASTENERS AND PARTS
S
Spark Plug Boot
S
Air Filter
S
Housing Screws
S
Assist Handle Screw
S
Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S
ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position. Make sure engine stops;
then restart engine and continue.
S
Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S
Debris Shield -- Discontinue use of unit if
debris shield is damaged.
INSPECT AND CLEAN UNIT AND
LABELS
S
After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S
Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts by pressing button to re-
lease air filter cover.
NOTE:
To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter;
squeeze the filter to distribute oil.
6. Replace parts.
Air Filter
Air Filter
Cover
Button
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at
0.025 in. Ignition timing is fixed and
nonadjustable.
1. T w ist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 in.
socket wrench.
4. Reinstall the spark plug boot.
SERVICE AND ADJUSTMENTS
LINE REPLACEMENT
Pre--wound spools offer the most convenient
method for replacing line and ensuring opti-
mum performance.
S
Replacement spools are color--coded to
ensure use of the correct spool with your
unit. Be sure to use the same color spool as
the existing spool.
NOTE:
Always clear dirt and debris from
cutting head components when performing
any type of maintenance.
S
Hold spool and unscrew cap by turning in
the direction shown on top of the cap.
S
Remove line guide ring and spool.
Cap
Spool
Line guide ring
Use a pre--wound spool or refill spool with
line. If using a pre--wound spool, remove tape
strip from line and spool.
REFILLING THE SPOOL WITH LINE
WARNING:
Use only .080” (2 mm)
diameter round line.
Other sizes and
shapes of line will not advance properly and
will result in improper cutting head function or
can cause serious injury. Do not use other
materials such as wire, string, rope, etc. Wire
can break off during cutting and become a
dangerous missile that can cause serious in-
jury.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
13
1. Cut a length of 30 feet of 0.080
!
(2 mm)
diameter round Weed Eater
"
brand line.
Feed line in
direction
shown on
spool.
Spool
2. Insert one end of line into center cavity of
empty spool. Ensure line will feed into
spool in the direction shown on the spool
(counterclockwise).
3. Continue feeding line into spool, leaving
4 -- 6 inches (10 -- 15 cm) unwound from
center of spool.
INSTALLING SPOOL WITH LINE
1. Install replacement spool.
2. Thread line through line guide ring.
Line through guide ring
Replacement Spool
Slot
3. Rest guide ring on spool and place line
through slot. Allow line to extend 4 -- 6
inches (10 -- 15 cm) from center of spool.
4. Ensure line remains in slot while screw-
ing cap on to the shaft.
Only tighten cap
hand tight!
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps.
Carburetor adjustment is a complicated task.
We recommend that you take your unit to an
authorized service dealer. Damage will occur
if you turn the needles beyond the limiter
stops.
STORAGE
WARNING:
Perform the following
steps after each use:
S
Allow engine to cool before storing or trans-
porting.
S
Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S
Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S
Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S
Clean the entire unit before lengthy
storage.
S
Store in a clean dry area.
S
Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
ENGINE
S
Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S
Replace spark plug with new one of recom-
mended type and heat range.
S
Clean air filter.
S
Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S
At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
OTHER
S
Do not store gasoline from one season to
another.
S
Replace your gasoline can if it starts to rust.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
14
TROUBLE CAUSE REMEDY
Engine will not
start.
1. ON/OFF switch in
OFF position.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
6. Carburetor requires
adjustment.
1. Move ON/OFF switch to ON.
2. See “Starting a Flooded Engine” in
Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. See “Carburetor Adjustment” in
Service and Adjustments Section.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
smokes
excessively.
1. Choke partially on.
2. Fuel mixture incorrect.
3. Air filter dirty.
4. Carburetor requires
adjustment.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in
Service and Adjustments Section.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
WARNING:
Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLESHOOTING TABLE
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
15
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each
new
Weed Eater
"
""
"
brand gasoline tool or at-
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
2 YEARS
-- Parts and Labor, when used for
household purposes.
90 DAYS
-- Parts and Labor, when used for
commercial, professional, or income produc-
ing purposes.
30 DAYS
-- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use
of accessories and/or attachments not spe-
cifically recommended by
ELECTROLUX
HOME PRODUCTS, INC.,
for this tool. Addi-
tionally, this warranty does not cover tune-
ups, spark plugs, filters, cutting line, or rotat-
ing head parts that will wear and require
replacement with reasonable use during the
warranty period. This warranty does not cov-
er predelivery setup or normal adjustments
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VAR Y FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of
ELECTROLUX HOME PROD-
UCTS, INC.,
is to continuously improve its
products. Therefore,
ELECTROLUX HOME
PRODUCTS, INC.,
reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obliga-
tion to any purchaser.
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR W ARRANTY RIGHTS AND OBLIGA-
TIONS:
The U. S. Environmental Protection
Agency and POULAN/WEED EA TER, DIVI-
SION OF WCI OUTDOOR PRODUCTS, INC.,
are pleased to explain the emissions control
system warr anty on your year 2001--2004 small
off--road engine. POULAN /WEED EA TER
must warrant the emission control system on
your small off--road engine for the periods of
time listed below provided there has been no
abuse, neglect, or improper maintenance of
your small of f--road engine. Your emission con-
trol system includes parts such as the carbure-
tor and the ignition system. Where a warr ant-
able condition exists, POULAN/WEED EATER
will repair your small off--road engine at no cost
to you. Expenses covered under warranty in-
clude diagnosis, parts and labor .
MANUFAC-
TURER’S WARRANTY COVERAGE:
If any
emissions related part on your engine (as listed
under Emissions Control War r anty Parts List) is
defective or a defect in the materials or w ork-
manship of the engine causes the failure of such
an emission related part, the part will be repaired
or r eplaced by POU LAN/WEED EATER.
OWNER’S W ARRANTY RESPONSIBILI-
TIES:
As the small off--road engine owner, you
are responsible for the performance of the re-
quired maintenance listed in your instruction
manual. POULAN/WEED EATER recom-
mends that you retain all receipts covering
maintenance on your small off--road engine, but
POULAN /WEED EA TER cannot deny warran-
ty so lely for the lack of rec eip ts or for your failure
to ensure the performance of all scheduled
maintenance. As the small off--road engine
owner, you should be aware that POU LAN/
WEED EATER may deny you warranty cover-
age if your small off--road engine or a part of it
has failed due to abuse, neglect, improper main-
tenance, unappr oved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsible
for presenting your small off--road engine to a
POULAN /WEED EATER authorized repair
center as soon as a problem exists. War r anty
repairs should be completed in a reasonable
amount of time, not to exceed 30 days. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN /WEED EA TER at 1--800--554--6723.
W ARRANTY COMMENCEMENT DATE:
The
war ranty period begins on the date the small
off--road engine is purchased.
LENG TH OF
COVERAGE:
This warranty shall be for a peri-
od of two years from the initial date of purchase.
WH AT IS COVERED: REPAIR OR RE-
PLACEMENT OF PARTS.
Repair or replace-
ment of any warr anted part will be performed at
no charge to the owner at an approved POU-
LAN/WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN /WEED EA TER at 1--800--554--6723.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
16
W ARRANTY PERIOD:
Any warr anted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled only
for regular inspection to the effect of ”repair or
replace as necessary” shall be warranted for 2
years. Any war r anted part which is scheduled
for replacement as required maintenance shall
be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS:
The owner shall not be charged
for diagnostic labor which leads to the deter-
mination that a war ranted part is defective if the
diagnostic work is performed at an approved
POULAN/WEED EATER ser v icing center.
CONSEQUENTIAL DAMAGES:
POULAN/
WEED EATER may be liable for damages to
other engine components caused by the failure
of a warr anted part still under warranty.
WHAT
IS NOT COVERED:
All failures caused by
abuse, neglect, or improper maintenance are
not covered.
ADD--ON OR MODIFIED
P ARTS:
The use of add--on or modified parts
can be grounds for disallowing a warranty claim.
POULAN /WEED EA TER is not liable to cover
failures of war ranted parts caused by the use of
add--on or modified parts.
HOW TO FILE A
CLAIM:
If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
cente r or call POU L AN/WEED EA TER at
1--800--554--6723.
WH ERE TO GET WAR-
RANTY SERVICE:
War r anty services or re-
pairs shall be provided at all POULAN/WEED
EA TER service centers. Call 1--800--554--6723.
MAINTENANCE, REPLACEMENT AND RE-
PAIR OF EMISSION RELATED P ARTS:
Any
POULAN/WEED EA TER approved replace-
ment part used in the performance of any war-
ranty maintenance or repair on emission related
parts will be provided without charge to the own-
er if the part is under warranty.
EMISSIO N
CONTROL W ARRANTY PARTS LIST:
Car-
buretor, Ignition System: Spark Plug (covered
up to maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT:
The owner is
responsible for the perform ance of all required
maintenance as defined in the instruction
manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Weed Eater 4000C User manual
- Category
- Power tools
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Weed Eater TE475 User manual
-
-
-
-
-
-
-
-
Weed Eater WE EL-11 Owner's manual
-
