RCA DRC99310U User manual

Brand: RCA

Model: DRC99310U

Category: DVD players

Type: User manual

This manual is also suitable for

DRC99370U

DRC99370U

user manual

Read these instructions before using your new product for the rst time.

AVC Multimedia,

Markham, Ontario L3R 1E3

http: //www.RCAav.com

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. O n ly use atta c hm e nt s /ac ce s sor ies spec ifi ed by t h e

manufacturer.

12. Use only with a cart, stand, tripod, bracket,

or table specied by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time.

14. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as the AC power cord or plug is damaged, liquid

has spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block the ventilation openings. Install in accordance

with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that

produce heat.

9. Do not defeat the safety purpose of a polarized or grounding

- type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong

are provided for your safety. If the provided plug does not t

into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched

Important Safety Instructions

Safety Precautions

* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *

WARNING: Should any trouble occur, disconnect the AC power adapter and refer servicing to a qualied technician.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT PLACE

OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

The lightning flash with an arrowhead

symbol, within the equilateral triangle,

is intended to ale r t the user to the

presence of uninsulated "dangerous

voltage" within the product's enclosure that may be

of sucient magnitude to cause an electric shock.

The excl a m ati o n po i nt wi t h in th e

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in this owner’s manual.

E - 1

This product contains a

low power laser device.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

On Placement

• Donotusetheunitinplacesthatareextremelyhot,cold,dusty,orhumid.

• Placetheunitonaatandevensurface.

• Donotrestrict the air owof the unit byplacingit in aplacewith poor air ow,bycovering it withacloth, or byplacingit on

carpeting.

• Toavoidmagnetizing,donotplacetheunitnearspeakersormagnets.

• Do notuse this unit indirectsunlight or leavethe unit ina closed automobile (or similarenvironments) where itwould be

exposed to high temperatures above 104°F (40°C).

• NonakedamesourcessuchaslightedcandlesshouldbeplacedontheACpoweradapterorthemainunit.

• The AC/DCadaptor and apparatus should not be exposedtosplashingordripping liquids,and no objectslled with liquids,

such as vases, should be placed on the AC/DC adaptor and apparatus.

• Theapparatusshouldnotbeexposedtodripping or splashing and that noobjects lled with liquids, such as vases, should be

placed on apparatus.

On Safety

• Whenconnecting ordisconnectingthe ACpower adapter,gripthe plugand not thecord itself.Pullingthe cordmay damageit

and create a hazard.

• Whenyouarenotgoingtousetheunitforalongperiodoftime,disconnecttheACpoweradapter.

On Condensation

• Whenleft inaheatedroom where it is warm and damp,water droplets or condensation may form inside theunit.When there

is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours before turning the power

on, or gradually heat the room and allow the unit to dry before use.

Ventilation Warning

• Do not block the ventilation openings or holes. Iftheventilationopeningsorholes are blockedbya newspaper or cloth, etc.,

the heat may not be able to get out.

• Donotoperatetheunitinaconnedspace,suchasabookcaseorbuilt-incabinet.Allowabout4inches(10cm)offreespaceall

around the unit for adequate ventilation.

Rating Plate Location

• Theratingplateislocatedonthebottomofunit.

FCC Statements

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Notes on Copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material without permission.

Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use

of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses

only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Please check and identify the supplied accessories.

Remote Control (with battery) ..................................................................................................................................................................x 1

AC Power Adapter ..........................................................................................................................................................................................x 1

Car Power Adapter .........................................................................................................................................................................................x 1

Accessories

Control Reference Guide

1. LCD screen

2. HDMI jack

3. DC IN 9V - 12V jack

4. AUDIO / VIDEO OUT jack

5. CHARGE / STANDBY / ON switch

6. VOLUME control

Adjusts the volume.

7. Headphone jack

8. STOP button

Press to stop playing a disc.

MENU button

Accesses DVD Disc Menu if DVD disc is currently

playing.

Accesses Setup menu if disc is not playing.

button

Press to start or resume playback of a disc.

Unit

Pressing during playback of a disc will cause

playback to be paused.

PREV button

Press to go back to the previous title / chapter / track.

In DVD Menu or Setup Menu, press to scroll left.

SEARCH button

Press to scroll up, press to perform fast forward

playback during CD playback.

In DVD Menu, Setup Menu or JPG Menu, press to

scroll up.

NEXT button

Press to advance titles / chapters / tracks.

In DVD Menu or Setup Menu, press to scroll right.

SEARCH button

Press to scroll down, press to perform fast reverse

playback during CD playback.

In DVD Menu, Setup Menu or JPG Menu, press to

scroll down.

9. SD Card Slot

USB Connector port

10. Disc Door

Push to close the disc door.

11. OPEN knob

Press the open knob to open the disc door.

12. Remote sensor

Senses the remote control's signals.

13. ON indicator

14. CHARGING indicator

Charge the rechargeable battery before using it for

the first time. Complete charging typically takes

approximately 4-5 hours. The charging light will go

out when the battery becomes fully charged.

Battery Replacement

When the battery becomes weak,

the operating distance of the remote

control will be greatly reduced and

you will need to replace the battery.

2. Insert one CR2025 (3V) size

battery.

To Change Remote Battery

1. Open the battery door.

Remove the

PLASTIC sheet

before USING the

Remote Control.

Note: If the remote control is not going to be used for a long time, remove the battery.

WARNING: Do not dispose of the battery in a re or it may leak and/or explode.

WARNING: Batteries should not be exposed to excessive heat such as sunshine, re or the like.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Using the Remote Control

• PointtheremotecontrolattheREMOTESENSORlocatedontheunit.

• When using this unit in very bright light, the infrared REMOTE

SENSOR may not work properly.

Remote Control

1. VIDEO MODE button

Adjust Brightness, Ratio and Contrast of the LCD screen.

2. PREV button

Move back through titles,

chapters or tracks on a disc.

3. / SEARCH buttons

SEARCH:

Fast reverse playback.

SEARCH:

Fast forward playback.

4. GOTO button

Skip directly to a location on

a CD/DVD.

5. Cursor ( , , , ) buttons

Move between selections on

a menu screen and adjust

certain settings.

ENTER button

Conrm selections on a menu

screen.

6. MEMORY button

Set titles/chapters/tracks in a favorite order.

7. Number (0 - 9) buttons

Use when creating programs or locating a title/chapter/track or

specic time.

8. REPEAT A-B button

Perform point-to-point repeat playback on a DVD or CD.

REPEAT DISC button

Repeat a DVD chapter or title.

Repeat a CD track or the whole disc.

SETUP button

In Stop Mode, press to display the

unit’s SETUP menu.

9. MENU button

Enter and exit the main DVD Menu.

10. NEXT button

Skip to next title, chapter or track on

a disc.

11. STOP button

Stop playing a disc.

PLAY button

Start or resume playback of a disc.

PAUSE button

Press once to pause playback. Press

subsequently to advance frame by

frame on a DVD.

12. DISPLAY button

Show status information on the

screen.

13. ANGLE button

Switch between mu ltiple ca mera

angles if applicable to the DVD.

14. AUDIO button

Select one of the audio sound

tracks on a DVD (if more than one is

available) or select the audio output

mode on a CD.

15. SUBTITLE button

Select one of the subtitle languages

programmed on a DVD (if available).

RETURN button

Return to normal operation af ter

using the SETUP menu of a DVD.

SUBTITLE/

RETURN

98 07

ENTER

MEMORY

DISPLAY

AUDIO

GOTO

VIDEO

MODE

STOP

PAUSE

PLAY

ANGLE

SETUP

A-B DISC

REPEAT

The unit can play back

Region Management Information

Region Management Information: This unit is designed and manufactured to respond to the Region Management

Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number

of this unit, it cannot play that disc.

The region number of this unit is 1.

Note on Unauthorized Discs

You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area

or made for business purposes.

DVDs

[8cm/12cm disc]

Compatible

Audio CDs

[8cm/12cm disc]

Disc Function or Operation That is Not Available

When the symbol appears on the screen, it indicates the function or operation attempted is not available at that time. This

occurs because the DVD manufacturer determines the specic functions of DVDs. Certain functions may not be available on

some DVDs. Be sure to read the documentation provided with the DVD.

Icons Used on DVDs

Sample lcons

Note:

When playing back a CD-G (Graphics) or CD

EXTRA disc, the audio portion will be played, but

the graphic images will not be shown.

Language selections for audio

Language selections for subtitles

Screen aspect ratio

Multiple camera angles

Region code indicator

Titles, Chapters and Tracks

• DVDs are dividedinto “titles” and “chapters”. If the disc has more

than one movie on it, each movie would be a separate “title”.

“Chapters” are sections of titles.

• Audio CDs aredivided into “tracks”. A “track” is usually one song

on an Audio CD.

Note: Numbers identify each title, chapter, and track on a disc. Most discs

have these numbers recorded on them, but some do not.

Disc Formats

Chapter1

Title1 Title2

Chapter2 Chapter3 Chapter1 Chapter2

Track1 Track2 Track3 Track4 Track5

Maintenance

Cleaning the Disc

A defective or soiled disc inserted into the unit can cause sound to drop out during playback.

Handle the disc by holding its inner and outer edges.

• DoNOTtouchthesurfaceoftheunlabeledsideofthedisc.

• DoNOTstickpaperortapeonthesurface.

• DoNOTexposethedisctodirectsunlightorexcessiveheat.

• Cleanthediscbeforeplayback.Wipethediscfromthecenteroutwardwithacleaningcloth.

• NEVERusesolventssuchasbenzineoralcoholtocleanthedisc.

• DoNOTuseirregularshapeddiscs(example:heartshaped,octagonal,etc.).Theymaycausemalfunctions.

Cleaning the Unit

• BesuretoturntheunitoanddisconnecttheACpoweradapterbeforecleaningtheunit.

• Wipetheunitwithadry soft cloth. If the surfaces areextremely dirty,wipe clean with a cloth that has been dipped in aweak

soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.

• Neverusealcohol,benzine,thinner,cleaninguidorotherchemicals.DoNOTusecompressedairtoremovedust.

Important Note

• Beforetransportingtheunit,removethediscfromthedisccompartment.

E - 2

To DC IN 9V - 12V Jack

Car power adapter

To cigarette

lighter socket

AC power adapter

To DC IN 9V - 12V Jack

To wall outlet

B. Using the Car Power Adapter

The 12V car power adapter allows the

unit to be used with vehicles that have a

12V, negative ground electrical system.

Warning:

Disconnect the car power adapter when

not in use. Not for use in 24V vehicles.

A. Using the AC Power Adapter

Caution:

• TheACpoweradapterincludedwiththisunitisforitsuseonly.Donotuseitwithotherequipment.

• Whentheunitisnotgoingtobeusedforlongtime,disconnecttheACpoweradapterfromthewalloutlet.

• When theAC poweradapter isplugged in,the apparatusis not completely disconnectedfrom themain

power supply, even when the power is turned o.

Warning:

The AC/DC adaptor is used as disconnect device. The AC/DC adaptor of apparatus should not be obstructed

OR should be easily accessed during intended used. To be completely disconnect the power input, the AC/DC

adaptor of apparatus shall be disconnected from the mains.

Power Supply

Th e suppli ed AC p ower ad apter

operates on AC 100-120V.

Caution:

• Usetheprovided 12V carpower

adapter only. Use with other car

power adapters could damage

the unit.

• Th e 1 2V c a r p ow er ad a pte r

included with this uni t is for

its use only. Do not use it with

other equipment.

• Intheinterestoftracsafety,donotoperatethisunitorviewvideoswhiledrivingavehicle.

• Makesuretheunitissecurelyfastenedtopreventitfromfallingoryingthroughtheairintheeventofan

accident.

• When the inside ofthe cigarettelighter socketis dirty with ashes ordust, theplug section may become

hot due to poor contact. Be sure to clean the cigarette lighter socket before use.

• Afteruse,disconnectthe12Vcarpoweradapterfromboththeunitandcigarettelightersocket.

C. Using the Built-in Battery

The unit has a built-in, non-

re pl a ce a b l e, re c ha rg e ab l e

bat t er y. Charge the bu ilt-in

battery before using it for the

first time. Complete charging

typically takes approximately

4-5 hours. The charging light will

go out when the built-in battery

becomes fully charged.

Warning:

• The built-in batterycan only berechargedwhen theunitis inCHARGE mode whileusing the AC power

adapter.

• Thebuilt-inbatterycannotberechargedwhentheunitisinONmode.

• DoNOTrechargethebuilt-inbatteryinavehicleusingthecarpoweradapter.

• Batteriesshouldnotbeexposedtoexcessiveheatsuchassunshine,reorthelike.

Note:

• When the built-inbatterypower is low, "BatteryLow" will displayon the screen and the unit will stop

playing.

• Rechargethebuilt-inbatterywhenyouarereadytouseitagain.

• Whileusingthebuilt-inbattery,theenvironmentaltemperatureshouldbe41°F(5°C)to95°F(35°C).

• Togetthelongestservicelifeofthebuilt-inbattery,chargeatindoor-temperature.

• The built-in batteryin this devicemay present a riskof fireor chemicalburn if mistreated. Donot

disassemble, heat above 212

F (100

C), or incinerate.

• Theunitshouldnotbeexposedtoexcessiveheatsuchassunshine,reorthelike.

• Whendiscardingthe unit,environmentalproblemsmust be consideredand localrules orlawsgoverning

the disposal of such products must be strictly followed.

Turning on the Unit

1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON

position.

2. The start-up picture will appear on the screen.

3. After use, slide the CHARGE / STANDBY / ON switch to the STANDBY (power off )

position.

To recharge the built-in battery

To AC power

outlet

To DC IN 9V

- 12V Jack

Slide the switch

to CHARGE

Charging

light ON

Recharging

is completed

when charging

light goes out

AC power

adapter

E - 3

B. Using Headphones/Earphones

• Turn downthe volume beforeconnecting, and thenadjust the

level.

• When headphones/earphones are connected,nosound willbe

emitted from the unit's speaker.

Caution:

Avoid listening to sound at levels which may be harmful to your ears.

Headphones

/Earphones

(3.5mm diameter plug)

(not included)

C. Connecting a USB connector port

Youcanconnect a USBash drive (not included)totheUSB port on theunit to play DivX® moviesaswellas

picture les.

• PlugtheUSBashdrivetotheUSBportontheunit.

• InDVDmode,press STOP button once to stop DVD playing, press STOP button three times to change

to USB mode.

Foroperation offile playback onthe USB flash drive, please refer tothe section“PLAYING DivX®VIDEO OR

PICTURE FILES”.

Note:

• ItisrecommendedUSBashdriveispluggedwhentheunitisinSTANDBYmode.

• It doesnot support USBharddiskmass storagedevice, multi-cardreaderand other USB computer

peripheral.

• ItonlysupportsUSBashdrive(FAT32/16max.capacity32Gbytesmax,videobitrateis7Mbps).

• Make sure your USBflashdriveorSD card is FAT16/FAT32file system. Allother file systemwill notbe

supported.

D. Using a SD Card Slot

You can connect a Secure Digital (SD) card (not included) to the memory expansion card slot on the unit to

play sound & picture les.

• PlugtheSDcardfullyintothememoryexpansioncardslotontheunituntilitclicks.

• InDVDmode,press STOP button once to stop DVD playing, press STOP button three times to change

to mode (DVD/USB/SD). In memory expansion card mode, it reads the information of the SD card and

playing the picture and/or sound le(s).

Warning:

• ItisrecommendedtheSDcardispluggedwhentheunitisinSTANDBYmode.

• IftheSDcardisorientedincorrectly,itwillnotgofullyintotheslot.Donotapplyforcewheninsertingthe

SD card.

• Toremovethe SD card, push theSD cardintothe slot and then slowly removeyourfinger,the lock is

released and the SD card is pushed out.

• MakesuretousecorrectAudio/Videocable,wrongplugconnectionmaycauseweaksignal.

• IfyouhaveastereoVCR,makesureyousetitinstereomode.

• Due tocopyright protection, DVDmovies cannot be copied.If you copya DVDmovie ontoa videotape,

the resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.

Note:

Pressing STOP button is for "function change" between DVD/CD/CD-ROM, USB and/or SD Card mode.

• Tostop, press STOP button. Pressing button can resume in previous playback position. If STOP

button is pressed three times, the unit trys to nd the content of disc ("LOADING..." is shown), to nd the

content of USB ("READ USB" is shown) and to nd the content of SD ("READ CARD" is shown).

• Tochangemedia(e.g.changeDVD/CD/CD-ROMtoUSB),press STOP twice for function change.

• IfonlyDVD/CD/CD-ROMexists,"NOUSB/NOCARD"isshownasindication.

• Please make sureyourUSB ash drive orSD card is FATle system insteadof NTFS le system.The DVD

unit does not support NTFS le system.

A. Connecting a TV

If your TV has audio/video inputs, you

can connect the unit to your TV using

standard Audio/Video cables.

Watching a DVD on your TV

1. Turn on the unit.

2. Turn on the T V and follow th e

instruc tions included with it to

watch video from external sources.

To AUDIO /

VIDEO OUT

jacks

Audio / Video cable

(not included)

White Red Yellow

Connections

E. Connecting to HDMI

HDMI (High Denition Multimedia Interface) supports both video and audio on a single digital connection for

use with DVD players, set-top boxes and other digital AV devices.

HDMI has the capability to support standard, enhanced or high-denition video plus standard to multi-channel

surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 2.2 gigabytes

per second (with HDTV signals), one connector (instead of several cables and connectors), and communication

between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo

and High-Denition Multimedia Interface are trademarks or registered

trademarks of HDMI licensing LLC.

For TVs that support it, HDMI can provide the best quality audio and video output (depending on media

source), and so is the preferred connection type. The HDMI cable (not included) incorporates both audio

and video signals, so you will have just one cable running from the unit to your TV. Using the HDMI cable

(not included), connect the HDMI OUT jack on your unit to the HDMI IN jack on your TV or HDMI-compatible

display.

Note:

• Connectthe cable from the source equipment (HDMI IN)to therearof this unit (HDMIOUT), besureto

turn o the power and unplug both units from the wall outlet before making any connections.

• WhenusingtheHDMIcable,donotconnecttootheranalogvideooutputs.

• In DVD mode, press STOP button once to stop DVD playing. In HDMI mode, it reads both video and

audio sources.

E - 4

The HDMI cable

(not included)

HDMI jack (on the rear of unit)

DRC99370U_ENGLISH IB_May 4.indd 1 2010-5-4 17:21:35

Adjust the LCD Screen

You can adjust Brightness, Ratio and Contrast of the LCD screen.

1. Press the VIDEO MODE button.

2. Press the / button to select Brightness, Ratio or Contrast.

3. Press the / button to change the setting.

4. Press the VIDEO MODE button to exit the menu.

This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a

manner that allows specic or limited operation during playback. Therefore, this unit may not respond to

all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the specic

DVD in question for more information about the options available on that DVD.

“ ” may appear on the screen during operation. A “ ” means the desired operation is not permitted

by the unit or disc.

Playing a Disc

1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON position.

See Customizing the function settings before proceeding to step 2.

2. Press the OPEN knob to open the disc door.

3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing

gently until you hear a “click”.

4. Close the disc door. It takes a short while for your unit to load the disc. After loading, the unit will

automatically bring you to the main menu of the DVD or start playing the DVD.

5. If the unit does not automatically start playing the DVD, press the P L AY button on the remote control

or button on the unit.

Pausing Playback (Still Mode)

Press the PAUSE button. To resume normal playback, press the PLAY button on the remote control or

button on the unit.

For a DVD, each time you press the PAUSE button on the remote control, the picture advances one frame.

Stopping Playback

Press the STOP button at the location where you want to interrupt playback. To resume playback at the

position where the disc was stopped, press the PLAY button on the remote control or button on the unit.

If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY button on the

remote control or button on the unit will reset the DVD to the beginning.

Fast Forward / Fast Reverse

1. Press the SEARCH or SEARCH button when a disc is

playing. Each time you press the SEARCH or SEARCH

bu tton, th e playb ack spee d change s in the following

sequence:

2. Press the P L AY button on the remote control or press the button on the unit when you reach the

desired point to resume normal playback.

Note:

• TheDVDplayermutessoundandsubtitlesduringreverseandforwardscanofDVDs.

• Thefastplaybackspeedmaydierdependingonthedisc.

Skip Forward / Reverse

• Pressthe NEXT button to advance titles, chapters/tracks.

• Pressthe PREV button to go back to current or previous titles, chapters/tracks.

• ForanAudioCD,usethenumberbuttonsontheremotecontroltogodirectlytothedesiredtracknumber.

Audio Selection

On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the preferred

language and sound system.

1. While a disc is playing, press the AUDIO button to show the current

audio format number.

2. Press the AUDIO button repeatedly to select the desired audio format.

Note:

• IfonlyoneaudioformatisrecordedontheDVD,thenumberdoesnotchange.

• SomeDVDs allow youto change audioselections using thedisc menu only.If this isthecase,press the

MENU button and choose the appropriate language on the disc menu.

• You can select differentaudio channels(Left, Right, Monoor Stereo) onanAudio CD bypressing the

AUDIO button repeatedly.

Subtitle Selection

1. While a DVD is playing, press the SUBTITLE button to display the

current language setting, as shown in the example.

2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles o by

pressing the SUBTITLE button repeatedly until the “ OFF ” is displayed.

Note:

• Some DVDsare set todisplay subtitles automatically, and you cannot turn themoffeven ifyou set the

subtitle function to o.

• Duringsomescenes,thesubtitlesmaynotappearimmediatelyafteryouselectyourdesiredscene.

• Thenumberofsubtitlelanguagesrecordeddiersdependingonthedisc.Ifonlyonelanguageisrecorded,

the language does not change.

• Thisfunctioncanonlybeusedfordiscsonwhichsubtitleshavebeenrecordedinmultiplelanguages.

• Some DVDs allowyou tochangesubtitles usingthedisc menuonly.Ifthis isthecase, press the MENU

button and choose the appropriate subtitle on the disc menu.

Angle Selection

Some DVDs contain scenes that have been shot from a number

of dierent angles. For these discs, the same scene can be viewed

from each of these dierent angles.

1. While you are playing a DVD with different angles recorded,

press the ANGLE button to view the number of current angles

available.

2. Press the ANGLE button repeatedly to change the scene to the

next recorded angle.

• Afterapprox.twoseconds,playback will continue

from the new angle selected.

• Ifnobuttonispressedwithin10seconds,playback

continues without changing the current angle.

Note:

This function can only be used for discs on which scenes

shot from multiple angles have been recorded.

Display Function

While the disc is playing, press the DISPLAY button

repeatedly to display information on operation status.

Elapsed Time:

Elapsed time from the beginning of the chapter/title

which is currently playing.

Remaining Time:

Remaining time of the chapter/title which is currently

playing.

Playing a Disc (Basic Playback)

[ 1 ENGLISH ]

[ 1 ENGLISH D5.1CH ]

E - 5

You can play a specic DVD title or chapter repeatedly (title repeat, chapter repeat, A-B repeat).

Repeating a Chapter

1. While the DVD is playing, press the REPEAT DISC button until the “ Repeat Chapter ” indicator displays on

the screen. The current chapter is played repeatedly.

Repeating a Title

2. While the DVD is playing, press the REPEAT DISC button until the “ Repeat Title ” indicator displays on the

screen. The current title is played repeatedly.

To Resume Normal Playback

3. While the DVD is playing, press the REPEAT DISC button until the “ Repeat all ” indicator displays on the

screen.

You can play a single CD track or the whole disc repeatedly.

Repeating a Single Track

1. While the CD is playing, press the REPEAT DISC button until the “ Repeat single ” indicator displays on the

screen. The current track is played repeatedly.

Repeating the Whole Disc

2. While the CD is playing, press the REPEAT DISC button until the “ Repeat all ” indicator displays on the

screen. The whole disc is played repeatedly.

To Resume Normal Playback

3. While the CD is playing, press the REPEAT DISC button until the “ O ” indicator displays on the screen.

Repeating a Specic Section

You can play a specic section repeatedly.

1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“ Repeat A- ” is

displayed) you want to play repeatedly.

2. Press the REPEAT A-B button again at the end of the section (“ Repeat A-B ” is displayed).

3. The unit will immediately begin replaying your selection.

To Resume Normal Playback

4. While the disc is playing, press the REPEAT A-B button until the “ Repeat A-B O ” indicator displays on

the screen (the repeat indicator disappears from the screen for a CD). The system will return to normal

playback.

Note:

• SomediscsmaynotpermitA-Brepeatoperation.

• YoucannotsettheA-Brepeatfunctionforasegmentthatincludesmultiplecameraangles.

• Youcanspecifyasegmentonlywithinthecurrenttitleortrack.

• There maybeaslight differencebetween point A andthelocation where playbackactually resumes

depending on the disc.

Repeat Playback

PlayingDivX®VideoorPictureles

ThisunitcanplayDivX®andpicturelesrecordedonCD-R/CD-RWdiscs,USBashdriveandSDcard.

To play video les on this product you must rst convert them to DivX format using the DivX Plus Player

on your PC or MAC. This application can be downloaded at www.divx.com. Please do so, and then install

on your PC or MAC.

PlayingDivX®Video/PictureFiles

If playing DivX video or picture files from a USB drive or SD card, see note

below.

1. Press the OPEN knob to open the disc door.

2.PlaceaDivX®/picturelediscontothetraywithlabelsideup.

3. Close the disc door.

4. A selection menu will appear on the screen.

5. Press or button to select the picture or video icon, and then

press ENTER.

If picture mode is selected, use below to nevigate the menu:

/ : selects a le

/ : page up or down

RETURN : returns to previous menu

ENTER : plays your selected le

Note:

•Forplaying lesonUSB ashdrive orSD card, you should plug intheUSB ashdrive or SDcardwhen the

unit is in STANDBY mode. then follow step 5.

•Youcanpressthe button to interrupt playback, and press the PLAY button to resume playback.

•YoualsocanusetheGOTObuttonorusethenumberedbuttonstoenteraphotonumberandquicklyselect

any image.

•Duringplayback,pressANGLEbuttonrepeatedlytorotatethepicture.

ABOUTDIVXVIDEO: DivX®isadigitalvideoformatcreatedbyDivX,Inc.Thisis anocialDivXCertieddevice

that plays DivX video. Visit www.divx.com for more information and software tools to convert your les into

DivX video.

ABOUT DIVXVIDEO-ON-DEMAND:This DivXCertied® devicemust be registeredin order to playDivXVideo-

on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup

menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX

VOD.

DivXCertifed®toplayDivX®video,includingpremiumcontent.

ENTER

Language Setup

1. Press the SETUP button on the remote control or MENU button on the

unit in stop mode (when disc is not playing).

2. Press the button to select Language Menu.

3. Press the / button to select the option, then press the button.

4. Press the / button to select your preferred language, then press the

ENTER button to conrm.

5. Repeat steps 3 and 4 to adjust other options.

6. Press the SETUP or RETURN button to exit the menu.

Note:

• SomeDVDsmaynotplayintheaudiolanguageyouselected.Apriorlanguagemaybeprogrammedonthedisc.

• SomeDVDsmaybesettodisplay subtitles in a language other than the one youselected.Apriorsubtitle

language may be programmed on the disc.

• Some DVDs allowyoutochange subtitleselectionsusing the discmenuonly.Ifthis is thecase,pressthe

MENU button and choose the appropriate subtitle language from the selection on the disc menu.

• Some DVDsmay not include your pre-selected language. Inthis case,

the DVD player automatically displays disc menus consistent with the

disc's initial language setting.

Video Setup

1. Press the SETUP button on the remote control or MENU button on the

unit in stop mode (when disc is not playing).

2. Press the / button to select Video Menu.

3. Press the / button to select the option, then press the button.

4. Press the / button to adjust the setting, then press the ENTER

button to conrm.

5. Repeat steps 3 and 4 to adjust other options.

6. Press the SETUP or RETURN button to exit the menu.

Customizing the Function Settings

E - 6 E - 7

Dolby Digital

Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can

reproduce from one to 5.1 discrete channels of excellent quality audio.

The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-

channel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel

soundtracks available on many DVDs.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Sound System

E - 8

Troubleshooting Guide

Printed in China

811-937091W040

Symptom Cause (and remedy)

No power.

The remote

control does

not function.

No sound or

only a very

low-level

sound is

heard.

No picture.

The picture is

not clear.

Severe hum or

noise is heard.

The disc does

not play.

No sound is

input from the

HDMI IN.

• EnsuretheACpoweradapterisconnected.

• Theunitisnotturnedon.

• Makesuretheinfraredremotesensorisnotblocked.

• Makesuretheplasticsheethasbeenremovedfromtheremotecontrol.

• Pointtheremotedirectlyattheinfraredremotesensorontheunit.

• Replacethebatteryintheremotecontrolwithanewone.

• Thevolumecontrolislocatedonthesideoftheunit–pleasetryadjustingthis.

• Thesystemisinpausemode.Pressthe button to return to normal play mode.

• Theunitisinfast-forwardorfast-reversemode.Pressthe PLAY button on remote control

to return to normal play mode.

• MakesuretheAUDIO/VIDEOoutputconnectionsarecorrect.

• TheDTSDVDcannotbedecodedtohavespeakeroutput.

• Theunitistoohot;shutotheunitfor30minutestocoolitdown.

• Theregion number of thediscdoesn'tmatchthe region

number of this unit.

• Cleanthedisc.

• Thediscisscratched.

• AdjusttheLCD'sbrightnessandcontrastusingthe VIDEO MODE button on the remote control.

• Theplugsandjacksaredirty.Wipethemwithaclothslightlymoistenedwithalcohol.

• Cleanthedisc.

• Thereisnodiscinside(“NoDisc”appearsonthescreen).

• Insertthedisccorrectlywiththeplaybacksidefacingdown.

• Cleanthedisc.

• Anon-NTSCdischasbeeninserted.Theunitanddiscregionnumberareincompatible.

• Condensation may have formed inside the unit due toasudden changein temperature.

Wait about an hour for it to clear and try again.

• ChecktheconnectionbetweenthisunitandtheHDMIINjackofotherequipment.

• SeeifyourTVsupportsthis480p/576p/720p/1080iDVDsystem.

• MakesureyourTVsupportsHDCP(HighBandwidthDigitalContentProtection).

Need More Help?

Please visit online help at http://www.RCAav.com

Specications and external appearance are subject to change without notice.

System Setup

1. Press the SETUP button on the remote control or MENU button on the

unit in stop mode (when disc is not playing).

2. Press the / button to select TV System Menu.

3. Press the / button to select the option, then press the button.

4. Press the / button to adjust the settings, then press the ENTER

button to conrm.

5. Repeat steps 3 and 4 to adjust other options.

6. Press the SETUP or RETURN button to exit the menu.

Default

It takes 3-5 seconds to reset the DVD settings to the factory default.

View DivX(R) VOD

DivX® Registration

DivX®registrationcodeallowsyoutorentandpurchasemoviesusingtheDivX®VODservicefromtheinternet.

This menu setting will display the registration code of your unit as follows:

YOU MUST REGISTER YO UR DEVICE TO PLA Y

DIVX PROTECTED VIDEOS.

REGISTRATION CODE:

Registration service at http://vod.divx.com

Follow the instructions and download the movie from your computer onto a CD-R/RW or DVD+R/-R or

DVD+RW/-RW for playback on the unit.

Note:

• ThisregistrationcodeisforDivX®Video-On-Demandonly.Do not applythiscodeforotherapplicationsor

websites.

• Ifyouhavealreadyregisteredthisproduct,selectingtheViewDivX(R)VODsettingwillallowyoutoderegister

(deactivate) the product for DivX playback - we recommend you DO NOT deregister the product.

Screen Saver

To turn on or o the screen saver (screen protection to prevent image burn).

Note:

When you leave the unit in DVD stop mode for approxiamtely 5 minutes, the screen saver of the unit

automatically appears if you set the Screen Saver to On mode. To turn o the screen saver, press the PLAY

button.

TV Display

Depending on the format of the DVD disc, you can choose the picture format (aspect

ratio) best suited the format of your TV screen.

4 : 3PS

• When wide-screen videoisplayed, this modeclips theright and left sidesofthe

image so that it can be viewed on a conventional screen.

• Somewide-screenDVDsthatdonotpermitPanScanmodeplaybackareautomatically

played in letterbox mode (black bands that appear at the top and bottom of the

screen).

4 : 3LB

• Whenwide-screenvideoisplayedinthismodeonaconventionalscreen,blackbands

appear at the top and bottom of the screen.

16 : 9

• Thisis the correctmode forplaying wide-screen videos onthe unit screenor other

external wide-screens.

Note:

• The displayablepicture size ispreset ontheDVD.Thereforetheplayback pictureof

some DVDs may not conform to the picture size selected.

• WhenyouplayDVDsrecordedinthe4:3 aspect ratio,the playbackpicturewillalways

appear in the 4:3 aspect ratio regardless of the TV display setting.

• Select16:9toconformtheLCDscreenontheunit.AlwaysbesurethatyourTVdisplay

conforms to the actual TV in use if you connect the unit to a TV.

HDMI Res. (Resolution)

You can set the HDMI Res. (Resolution) to be Auto, 480p, 720p, 1080i or 1080p, according to the connected TV.

Note:

• SelecttheHDMIresolutionaccordingtotheperformanceoftheconnectedTV.

• IftheVideooutisnotsettoHDMI,youcannotselecttheHDMIRes.

JPEG Interval

To set the JPEG Interval for slide show playback. Select O to disable the slide show feature.

O: Plays back one le at a time.

5 seconds Plays back images in the form of a slide show at 5 seconds interval.

10 seconds Plays back images in the form of a slide show at 10 seconds interval.

15 seconds Plays back images in the form of a slide show at 15 seconds interval.

Locating a Desired Section

Locating a Specic Chapter / Title

If you know the chapter/title number for the chapter/title that you want to play, you can locate it by directly

selecting that number.

1. Press the GOTO button.

2. Press the / button to highlight chapter/title number, then press the corresponding number buttons for

the chapter/title you want (for example: 02, 08, 10 or 15). Press the ENTER button to conrm.

3. Playback starts from the selected chapter/title.

Note:

• Ifthechapter/titlenumberenteredisnotpermitted.Repeatsteps1and2tore-enterthecorrectnumber.

• Somediscsmaynotrespondtothisprocess.

• Thismethodoflocatingachapter/titleisavailableonlyonaDVDthatcontainschapter/titlenumbers.

Locating a Specic Time

You can move to a specic location by entering its corresponding time (hours, minutes, seconds).

1. Press the GOTO button.

2. Press the corresponding number buttons (5 digits: X:XX:XX,

for example:

0 30 05, 1 08 23, 1 22 56) for the setting point you want.

3. Playback starts from the selected section.

Note:

• IfthetimeenteredisnotpermittedbytheDVD," " will display. You should re-enter the correct time.

• Somediscsmaynotrespondtothisprocess.

• Somescenesmaynotbelocatedaspreciselyasyouspecied.

• ThismethodforaccessingspeciclocationsisavailableonlywithinthecurrenttitleoftheDVD.

You can combine your favorite titles/chapters/tracks and play

them in the order you determine.

1. Press the MEMORY button and a program screen appears.

2. Select the items in the order you want by pressing the

number buttons. Each time you press the Cursor buttons ( ,

, , ), the space is highlighted. Highlight where you want

to enter, then press the corresponding number buttons.

3. Press th e Cursor buttons ( , , , ) to move the

highlighted bar to , then press the P LAY or ENTER

button. The DVD player starts memory playback.

4. To resume normal playback from memory playback

a) Press the MEMORY button.

b) Press the Cursor buttons ( , , , ) to move the

highlighted bar to “Clear”, then press the ENTER button.

All the input programs will be cleared.

c) Press the PLAY button to resume normal playback.

Note:

• If the title or ch a p t e r numbers yo u entere d i s not

permitted by the DVD, after you press the ENTER button,

it will restore to [- -]. You should re-enter correct numbers.

• Somediscsmaynotpermitmemoryplaybackoperation.

• Ifyouselect repeat during memoryplayback, the DVD

player repeats the current memory playback.

• If you press the MEMORY button while the display

appears on the TV screen, the display disappears.

• The programmedselections willbe cleared when you

open the disc tray or turn o the DVD player.

Programmable Memory

e.g. DVD

e.g. CD

x2 x4 x8 x20

Language

Player Menu

Subtitle

Audio

Disc Menu Lang

Video

TV Display

HDMI Res.

JPEG Interval

Default

View DivX(R) VOD

Screen Saver

TV System

16 : 9

4 : 3PS

Cut o when a wide-

screen video image

is played.

4 : 3LB

DRC99370U_ENGLISH IB_May 4.indd 2 2010-5-4 17:21:37

RCA DRC99310U User manual

Brand: RCA

Model: DRC99310U

Category: DVD players

Type: User manual

This manual is also suitable for

DRC99370U

Download PDF

report

RCA DRC99310U User manual

This manual is also suitable for

RCA DRC99310U User manual

Related papers

Other documents