Behringer Eurodesk SL3242FX-Pro User manual

Brand: Behringer

Model: Eurodesk SL3242FX-Pro

Category: Musical Instruments

Type: User manual

This manual is also suitable for

EURODESK SL3242FX-PRO/SL2442FX-PRO

User Manual

A50-24413-00002

EURODESK SL3242FX-PRO/SL2442FX-PRO

Important Safety Instructions

This symbol, wherever it appears, alerts you to the

presence of uninsulated dangerous voltage inside the

enclosure - voltage that may be sufcient to constitute

a risk of shock.

This symbol, wherever it appears, alerts you to im-

portant operating and maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, do not remove the +

top cover (or the rear section). No user serviceable parts

inside. Refer servicing to qualied personnel.

Caution

To reduce the risk of re or electric shock, do not expose +

this appliance to rain and moisture. The apparatus shall

not be exposed to dripping or splashing liquids and no

objects lled with liquids, such as vases, shall be placed

on the apparatus.

Caution

These service instructions are for use by qualied ser- +

vice personnel only. To reduce the risk of electric shock

do not perform any servicing other than that contained in

the operation instructions. Repairs have to be performed

by qualied service personnel.

Read these instructions.1)

Keep these instructions.2)

Heed all warnings.3)

Follow all instructions.4)

Do not use this apparatus near water.5)

Clean only with dry cloth.6)

Do not block any ventilation openings. Install in accor-7)

dance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, 8)

heat registers, stoves, or other apparatus (including

ampliers) that produce heat.

Do not defeat the safety purpose of the polarized or 9)

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

Place the power cord so that it is protected from being 10)

walked on and sharp edges. Be sure that the power cord is

protected particularly at plugs, convenience receptacles

and the point where it exits from the apparatus.

The apparatus shall be connected to a MAINS socket 11)

outlet with a protective earthing connection.

Where the MAINS plug or an appliance coupler is used 12)

as the disconnect device, the disconnect device shall

remain readily operable.

Use only attachments/accessories specified by the 13)

manufacturer.

Use only with the cart, stand, tripod, bracket, or table 14)

specied by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when 15)

unused for long periods of time.

Refer all servicing to qualied service personnel. Servic-16)

ing is required when the apparatus has been damaged in

any way, such as power supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the appa-

ratus, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Foreword

Dear Customer,

Welcome to the team of

EURODESK users and

thank you very much for

expressing your confi-

dence in BEHRINGER

products by purchasing

this mixing console.

It is one of my most pleas-

ant tasks to write this let-

ter to you, because it is

the culmination of many

months of hard work de-

livered by our engineer-

ing team to reach a very

ambitious goal: to present

you two outstanding mix-

ing consoles that give you

maximum flexibility and

performance with a unique

sound character and broad

range of striking functions. The task to design the new SL series

certainly meant a great deal of responsibility, which we assumed by

focusing on you, the discerning user and musician. It also meant a

lot of work and night shifts to accomplish this goal. But it was fun,

too. Developing a product usually brings a lot of people together,

and what a great feeling it is when everybody who participated in

such a project can be proud of what we’ve achieved.

It is our philosophy to share our joy with you, because you are

the most important member of the BEHRINGER team. With your

highly competent suggestions for new products you’ve greatly

contributed to shaping our company and making it successful.

In return, we guarantee you uncompromising quality as well as

excellent technical and audio properties at an extremely favorable

price. All of this will enable you to fully unfold your creativity without

being hampered by budget constraints.

We are often asked how we can make it to produce such high-

grade devices at such unbelievably low prices. The answer is

quite simple: it’s you, our customers! Many satised customers

means large sales volumes enabling us to get better conditions

of purchase for components, etc. Isn’t it only fair to pass this

benet back to you? Because we know that your success is our

success, too!

I would like to thank all people whose help on “Project SL” has

made it all possible. Everybody has made very personal contri-

butions, starting from the designers of the unit to the many staff

members in our company and nally to you, the user of BEH-

RINGER products.

My friends, it’s been worth the trouble!

Thank you very much,

Uli Behringer

Table of contents

1. Introduction ......................................................................... 4

1.1 Before you get started .................................................. 4

1.1.1 Shipment ............................................................. 4

1.1.2 Initial operation ................................................... 4

1.1.3 Online Registration ............................................. 4

1.2 The manual .................................................................. 4

2. Control elements and connections ................................... 5

2.1 Mono input channels .................................................... 5

2.1.1 Microphone and line inputs ................................. 5

2.1.2 Equalizer ............................................................. 5

2.1.3 Aux/FX send buses ............................................. 5

2.1.4 Mono channel fader

and further control elements ............................... 6

2.2 Stereo channels ........................................................... 6

2.2.1 Channel inputs .................................................... 6

2.2.2 Stereo channel equalizer .................................... 6

2.2.3 Stereo channel aux/FX send buses .................... 6

2.2.4 Stereo channel fader

and othercontrol elements .................................. 7

2.3 Stereo channels 21 - 24 (SL2442FX-PRO)

or 29 - 32 (SL3242FX-PRO) ........................................ 7

2.4 Subgroups 1 - 4 ............................................................ 7

2.5 Mono out section for subwoofer applications ............... 8

2.6 Main out section ........................................................... 8

2.6.1 Talkback .............................................................. 9

2.6.2 Phones & control room ....................................... 9

2.7 CD/tape ........................................................................ 9

2.8 Master aux send 1 and 2 .............................................. 9

2.9 Graphic 9-band stereo equalizer ................................ 10

2.10 Effects section .......................................................... 10

2.11 Rear panel .................................................................11

3. Digital effects processor.................................................. 11

4. Wiring examples ............................................................... 12

4.1 Studio set-up .............................................................. 12

4.2 Live set-up .................................................................. 13

5. Audio connectors ............................................................. 14

6. Presets............................................................................... 15

7. Specications ................................................................... 16

8. Warranty ........................................................................... 17

EURODESK SL3242FX-PRO/SL2442FX-PRO

Introduction4

Introduction1.

Congratulations! With the EURODESK you have acquired a state-

of-the-art mixing console that sets new standards. Right from the

very start it has been our goal to design a revolutionary unit that

can be used for a great variety of applications. And indeed, this

overwhelming mixing console gives you plenty of functionality and

a broad range of connection and expansion options.

BEHRINGER is a company with its roots in professional recording

studio technology. For many years now we have been successful

in developing products for studio and live use. These include mi-

crophones and studio gear of all kinds (compressors, enhancers,

noise gates, tube processors, headphone ampliers, digital effects,

DI boxes, etc.), monitor and P.A. speakers as well as professional

live and recording mixers. Our entire technical know-how has gone

into your EURODESK mixing console.

FBQ Feedback Detection System

One of the most outstanding features of this console

is the FBQ Feedback Detection System, which is

part of the graphic equalizer. This ingenious circuit

makes it possible to detect and subsequently

eliminate feedback frequencies very quickly. FBQ

increases the brightness of the EQ fader LEDs for the frequency

bands where feedback is occurring. What used to be a tedious

search for feedback frequencies is now mere child’s play.

IMP “Invisible” Mic Preamp

The microphone channels are equipped with

BEHRINGER’s brand-new high-end IMP Invis-

ible Mic Preamps, which offer you:

130 dB of dynamic range and hence an =

unbelievable amount of headroom,

a bandwidth from below 10 Hz to above 200 kHz for the crystal- =

clear reproduction of even the slightest details,

extremely noise and distortion-free circuitry for absolutely =

natural sound and neutral signal reproduction,

perfect adaptation to any microphone on the market (upto 60 =

dB gain and +48 V phantom power), and

the possibility of pushing the dynamic range of your 24-bit/192- =

kHz HD recorder to the max and thus achieving ultimate

audio quality.

What is more, the EURODESK comes with two ef-

fects processors using 24-bit A/D and D/A convert-

ers and the effects algorithms of our renowned 19"

multi-effects device VIRTUALIZER PRO DSP2024P.

Each processor offers 99 presets with rst-class room

simulations, delay and modulation effects as well as compressor,

tube distortion and numerous other effects available—all with

excellent audio quality!

The mixer is equipped with a state-of-the-art integrat-

ed switch-mode power supply. Unlike conventional

designs, this supply automatically adapts to supply

voltages between 100 and 240 V. With its consider-

ably higher efciency, it is also more economical in

terms of power consumption than standard power supply units.

Before you get started1.1

Shipment1.1.1

Your product was carefully packed at the factory to ensure safe

transport. Nevertheless, if the box is damaged inspect the unit

immediately for signs of damage.

If the unit is damaged please do NOT return it to us, +

but notify your dealer and the shipping company im-

mediately; otherwise, claims for damage or replacement

may not be granted.

We recommend that you use a ight case to give the unit +

optimum protection during use or transport.

Always use the original box to prevent damage during +

storage or transport.

Make sure that children cannot play unsupervised with +

the unit or its packaging.

Please ensure proper disposal of all packing +

materials.

Initial operation1.1.2

Ensure adequate air supply and to avoid overheating do not place

the unit near radiators etc.

Blown fuses must be replaced by fuses of the correct +

rating! Please refer to the "SPECIFICATIONS" section

for the applicable rating.

For connection to the mains use the enclosed power cord with cold

connector which complies with the relevant safety regulations.

Please make sure that all devices are properly grounded. +

For your own safety, never remove or disable the ground

conductors from the devices or on the power cords. The

unit must always be connected to the mains outlet with

a protective grounding connection.

We would like to point out that high volume levels +

may damage your hearing and/or your headphones/

loudspeakers. To avoid switch-on/off thumps from the

console and any downstream devices, always make

sure that your power amp(s) or active speakers are the

last components that are switched on and the rst to

be switched off. Always make sure that the appropriate

volume is set.

Important notes concerning installation

The sound quality may diminish within the range of pow- +

erful broadcasting stations and high-frequency sources.

Increase the distance between the transmitter and the

device and use shielded cables for all connections.

Online Registration1.1.3

Please register your new BEHRINGER equipment right after your

purchase by visiting http://www.behringer.com and read the terms

and conditions of our warranty carefully.

Should your BEHRINGER product malfunction, it is our intention

to have it repaired as quickly as possible. To arrange for warranty

service, please contact the BEHRINGER retailer from whom the

equipment was purchased. Should your BEHRINGER dealer

not be located in your vicinity, you may directly contact one of

our subsidiaries. Corresponding contact information is included

in the original equipment packaging (Global Contact Information/

European Contact Information). Should your country not be listed,

please contact the distributor nearest you. A list of distributors

can be found in the support area of our website (http://www.

behringer.com).

Registering your purchase and equipment with us helps us process

your repair claims more quickly and efciently.

Thank you for your cooperation!

The manual1.2

This manual is designed to give you an overview of all control ele-

ments and at the same time inform you in detail about how to use

them. To provide you with a clear structure, we have grouped the

control elements according to their function. They can easily be

found on the enclosed numbered illustrations. If you need more

detailed information on specic topics, please visit our web site

at www.behringer.com. The product-related information pages

and the ULTRANET-based glossary explain the relevant audio

engineering terminology in full detail.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections 5

Control elements and connections2.

This chapter describes the various control elements of your mixing

console. All controls and connections are explained in full detail.

Mono input channels2.1

Microphone and line inputs2.1.1

Connectors and controls of the mic/line inputsFig. 2.1:

{1} Each mono input channel is

equipped with a balanced microphone input

on an XLR connector, which provides +48 V

phantom power for condenser microphones at

the touch of a button (see rear panel).

Be sure to switch off your audio system before you +

activate the phantom power supply to prevent audible

switch-on thumps from reaching your monitor speak-

ers. Please also note the information given in chapter

2.11 “Rear panel”.

{2} Each mono input also has a balanced line input on 1/4" TRS

connectors. Of course, these inputs can also be used with

unbalanced plugs (1/4" TS connector).

{3} The INSERT I/O connector is used to process a signal with

dynamic processors or equalizers. This insert point ispre-

fader, pre-EQ and pre-aux send.

Unlike reverb and other effects, which are usually added to

the dry signal, dynamic processors process the entire signal.

So, aux send buses are not the best solution here. Instead,

dynamic processors and equalizers are inserted into the

signal path. Once processed, the signal then re-enters the

mixing console at the same point where it left. Signal inter-

ruption only occurs if a plug is inserted into the corresponding

jack (1/4" stereo plug: tip = signal output, ring = input). All

mono input channels are equipped with insert points. They

can also be used as pre-EQ direct outputs, without signal

ow interruption. For this you need a cable with a 1/4" TS

connector on the recorder/effects processor end, and a

bridged stereo 1/4" TRS connector on the console end (tip

and ring interconnected).

{4} The TRIM control adjusts the input gain. Be sure to set this

control fully counter-clockwise before you connect or discon-

nect a signal source to or from one of the inputs.

TRIM has a dual scale: the rst scale has a gain from +10

to +60dB for the MIC input.

The second scale has a gain from +10 to -40dBu for the line

input. For devices with a nomal line output level of-10 dBV

or +4 dBu the setting is as follows: with TRIM fully counter-

clockwise connect the external device and adjust the output

level recommended by the manufacturer. If available, the

output level display of the external device should read 0 dB

with signal peaks. For +4 dBu increase TRIM, for -10 dBV

increase it further. The ne-tuning can be done with a music

signal and the LEVEL SET LED, which will illuminate when

the optimum operating level has been set.

{5} Mono channels are equipped with a high-slope LOW CUT

lter eliminating unwanted low-frequency signals, such as

oor rumble (18 dB/oct., -3 dB at 80 Hz).

Equalizer2.1.2

All mono input channels are equipped with a 3-band equalizer.

The maximum boost/cut of the individual bands is 15 dB, in mid

position the EQ is set to neutral.

Equalizer section of input channelsFig. 2.2:

{6} The HI control in the EQ section controls the high frequency

range of the respective channel. It is a shelving-type lter

which can boost or cut all frequencies above a xed fre-

quency (12 kHz).

{7} The MID control allows you to raise or lower the mid-range

level. It is a semi-parametric peak lter, which boosts or cuts

the frequency range around a variable mid-range frequency.

Use the FREQ control to select the mid-range frequency

from 100 Hz to 8 kHz. Then use the MID control to boost or

cut the selected frequency range.

{8} The LOW control boosts or cuts the low-frequency range.

Like the HI lter it is a shelving-type lter, which raises or

lowers the level of all frequencies below a specic frequency

(80 Hz).

Aux/FX send buses2.1.3

Aux sends enable you to take the signals from one or multiple

channels and collect them on one bus. This signal is then present

at one of the aux send jacks, from where it can be routed to an

active monitor speaker or external effects device, for example.

The FX returns are subsequently used as a return bus for the

processed signal.

AUX/FX send controls in the channel stripsFig. 2.3:

{9} On each channel, the AUX 1 and AUX 2 controls allow

you to determine the level of the aux signals sent from the

channel. The main aux send signal comprising the aux send

signals from all channels can then be adjusted with the cor-

responding master AUX SEND controls (51), and is present

at the AUX SEND outputs (52). Both aux sends are mono,

post-EQ, with a gain of up to +15 dB.

(10) Press the PRE switch to set all aux sends to pre-fader. In

this case, the volume of the aux signals is no longer depen-

dent on the fader position, so you can create completely

independent monitor mixes.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections6

For most applications when controlling an external ef- +

fects device from one of the aux buses, the aux sends

must be set post-fader, so that the effect volume in a

channel depends on the position of the channel fader.

Otherwise, the effect signal would still be audible, even

if the channel was turned down completely. For this type

of application it is advisable to leave the PRE switch out

(= not pressed).

(11) FX 1 and FX 2 controls provide a direct route to the built-in

effects processor. Additionally, they can be used to control

an external effects unit, via the FX SEND 1 and 2 outputs

(similar to the AUX SEND 1 and 2 jacks). To ensure that the

internal effects processor and the FX SEND outputs actu-

ally get a signal, the corresponding FX control must not be

set fully counter-clockwise (-oo), and the master FX SEND

(see (60)) must be turned up. The FX buses are hard wired

post-fader.

Please also read chapter 2.10 “Effects section” and3 +

“DIGITAL EFFECTS PROCESSOR”.

Mono channel fader and further control 2.1.4

elements

Channel fader, pan control, mute button, etc.Fig. 2.4:

(12) The PAN control determines the position of the channel

signal in the stereo mix as well as the subgroup to which

the channel signal is routed (see chapter 2.4).

(13) Use the MUTE switch to mute the channel signal, so it is no

longer part of the main mix. At the same time, all aux buses

set to post-fader are muted for the respective channel, while

the pre-fader monitor buses remain operative. The MUTE

LED is illuminated when the channel is muted.

(14) The CLIP LED illuminates when the channel overloads.

In this case, please reduce the input gain using the TRIM

control. This LED also illuminates when you activate the solo

function with the SOLO switch below.

(15) The SOLO switch routes the channel signal to the solo bus

(Solo In Place) or the PFL bus (Pre Fader Listen). Thus,

you can monitor a channel signal without affecting the main

output signal. The signal to be monitored is taken either pre

(PFL, mono) or post-panorama control (Solo, stereo) and

post-channel fader (depending on the position of the SOLO/

PFL switch (40)).

(16) The SUB switch routes the signal to the respective sub-

groups. Your EURODESK features 4 subgroups (1-2 and

3-4). With the PAN control on the input channel (see (12))

you can determine to which of the two groups the signal is

routed (hard left: sub 1 or 3, hard right: sub 2 or 4).

(17) The MAIN switch routes the signal to the main mix.

(18) The channel fader governs the level of the channel signal

as part of the main mix (or submix).

Stereo channels2.2

Channel inputs2.2.1

Stereo channel inputsFig. 2.5:

(19) Each stereo channel is equipped with two balanced line-level

inputs on 1/4" TRS connectors for the left and right channels.

The channels can also process mono signal, as long as you

use the “LEFT” jack only.

(20) All stereo channel strips have a TRIM control for gain adjust-

ment. Its scale ranges from +20 to -20 dB and allows you to

adapt the input level to the line inputs.

Stereo channel equalizer2.2.2

Stereo channel equalizerFig. 2.6:

The stereo channels are equipped with a stereo equalizer. The

lter types and cutoff frequencies for HIGH and LOW lters are

the same as on the mono channels. Instead of one semi-paramtric

midrange band, the stereo channels have two separate midrange

bands ((21) HIGH MID and LOW MID) with xed mid-frequencies

(3 kHz and 400 Hz). Stereo EQs are preferable for processing the

frequency response of stereo signals. With two mono equalizers

you might encounter problems with different settings between the

left and right channels.

Stereo channel aux/FX send buses2.2.3

Basically, the aux and FX buses on the stereo channels are the

same as on the mono channels. Since aux buses are always mono,

the signal from a stereo channel is rst mixed to mono before it

is routed to the aux bus.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections 7

Stereo channel fader and othercontrol elements2.2.4

Channel fader, balance control, mute switch, etc.Fig. 2.7:

(22) The BAL(ANCE) control has the same function as the PAN

control on the mono channels. It determines the relative

volume of the left and right input signals before they are

routed to the stereo main mix bus (or to two subgroups).

All other control elements of the stereo channels work in the same

ways as their counterparts on the mono channels (faders, MUTE

switches, etc.).

Please note: When you route a stereo channel to the +

subgroups using the SUB switches, please be sure to

set the BAL control to its mid position, so that the signal

is sent to two subgroups and remains stereo.

Stereo channels 21 - 24 (SL2442FX-PRO) 2.3

or 29 - 32 (SL3242FX-PRO)

Auxiliary stereo channelsFig. 2.8:

Your EURODESK has two stereo channels with an aux send

section ((23) AUX 1 and AUX 2) and one LEVEL control (24). For

these channels, the aux buses are hard-wired to pre-fader and are

therefore particularly useful for monitoring. They have no routing

switches and are always sent to the main mix. Like the normal

stereo channels they have two line-level inputs on1/4" TRS con-

nectors for the left and right channels, and a SOLO switch.

Similar to the CD/TAPE inputs (see (49)) the auxiliary stereo

channels can be connected to CD players, tape decks, etc., for

example, to feed in playback material.

Subgroups 1 - 42.4

Subgroups 1 - 4Fig. 2.9:

The EURODESK has 4 subgroups enabling you to create mono or

stereo mixes from multiple input signals. Subgroups are controlled

from one (mono) or two (stereo) subgroup faders. Additionally, it

is possible to connect the subgroup outputs as tape sends to a

multi-track recorder.

(25) The subgroup faders determine the volume of the subgroup

signal at the subgroup output (28). Depending on the position

of the routing switch (27) you can thus control the subgroup

volume in the main mix.

(26) The SOLO switch routes the subgroup signal to the solo

bus (Solo In Place) or PFL bus (Pre Fader Listen), so that

you can monitor the subgroup signal without affecting the

main or sub output signals. The signal to be monitored is

taken either pre (PFL, mono) or post-subgroup fader(Solo,

stereo), depending on the position of theSOLO/PFL switch

(40)). The SOLO LED illuminates when the SOLO switch is

pressed.

(27) Use the routing switches for the subgroups to send the

subgroup signal to the main mix. You can route it to the

left stereo side (=LEFT pressed), to the right stereo side

(=RIGHT pressed) or to both (=LEFT and RIGHT pressed).

For example, when you have created a stereo submix using

subgroups 1 and 2, be sure to route group 1 to the left and

group 2 to the right side to maintain proper stereo position-

ing. If it is a mono submix with just one subgroup, route it to

the left and right sides of the main mix to make the signal

audible on both sides.

Subgroup outputs 1 - 4Fig. 2.10:

(28) These four SUBGROUP OUT (puts) carry the signals of the

individual subgroups. For multi-tracking connect the outputs

to the inputs of a multi-track recorder (see chapter 4.1 “Studio

set-up”).

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections8

Mono out section for subwoofer 2.5

applications

Using this auxiliary mono output you can route the main mix signal

to a separate power amp. The tunable low-pass lter allows you to

limit the signal content to the low-frequency range to get a perfect

subwoofer signal. This signal is mono because very low frequen-

cies disperse quickly, so there would be no benet to position this

signal in the stereo mix.

Mono out fader and low-pass lterFig. 2.11:

(29) The MONO fader controls the volume of the signal present

at the MONO OUT (see (32)).

(30) The FREQ control adjusts the cut-off frequency of the low-

pass lter (30 to 200 Hz). Frequencies above cut-off are

ltered out when activated.

(31) Use the LOW PASS FILTER switch to activate the lter

function (LED illuminates).

Mono out connectorFig. 2.12:

(32) The MONO OUT connector provides the line-level mono

signal for connection to the inputs of a power amp or active

speaker. You can also use this output as a monitor bus, e.g.

to connect a headphone amplier. In this case, the signal

should of course not be limited by the low-pass lter.

Main out section2.6

Main out faderFig. 2.13:

(33) Use this high-precision MAIN fader to control the output level

of the main mix.

XLR main out connectorsFig. 2.14:

(34) The MAIN OUT(puts) are balanced XLR connectors with a

nominal operating level of +4 dBu and provide the main mix

signal.

Main out connectors and main insertFig. 2.15:

(35) The MAIN OUT 1/4" TRS connectors outputs also provide

the main mix signal.

(36) Like the channel inserts, the MAIN INSERT connectors

can be used to connect a dynamics processor or equalizer

for further processing of the mix signal. The MAIN INSERT

refers to the Main Outs (XLR and 1/4" TRS connectors),

the MONO OUT (see (32)) and, if the MAIN switch in the

PHONES/CONTROL ROOM section is pressed, also to the

PHONES/CTRL ROOM output (see (46)).

Level meterFig. 2.16:

(37) The red “+48 V” LED illuminates when phantom power is on.

Phantom power is required for the operation of condenser

microphones, and can be switched on with the corresponding

switch on the rear of the console.

(38) The POWER LED is illuminated when the console is switched

on.

(39) The high-precision level meter accurately indicates the output

signal level. For example, when you press the SOLO switch

on one of the input channels, its signal level will be displayed

here, either pre-fader (PFL) or post-fader (SOLO), depending

on the position of the SOLO/PFL switch (see (40)). In PFL

mode only the left display is active, because the PFL signals

are mono.

(40) The SOLO/PFL switch determines whether the monitored

signal is pre (PFL) or post-fader (SOLO) after pressing the

SOLO/PFL switch (the LED illuminates). The level meter

indicates the corresponding signal (see (39)). When you

adjust a signal with the TRIM control, it is advisable to select

PFL mode, so that the level shown is independent of the

channel fader position.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections 9

Talkback2.6.1

The talkback function of the EURODESK allows you to commu-

nicate with the musicians in the recording room or on the stage.

The talkback signal is present at the AUX SEND outputs, which

are particularly useful for monitor/headphone mixes.

Talkback sectionFig. 2.17:

(41) The LEVEL control determines the volume of the talkback

signal at the AUX 1/2 outputs.

(42) Use the TALK TO AUX 1/2 switch to activate the built-in talk-

back microphone. Its signal is sent to the AUX SEND jacks

1 and 2. Keep the switch pressed while you’re speaking.

(43) This is the built-in talkback microphone.

Phones & control room2.6.2

Phones/control room sectionFig. 2.18:

(44) The PHONES/CTRL R control adjusts the volume of the

headphones connected to the PHONES/CTRL ROOM OUT

jack (see (46)). If you have an active monitor speaker or

power amp connected here, you can also control the monitor

volume.

(45) These switches select the signal sent to the PHONES/CTRL

ROOM jack. Available sources are: MAIN, CD/TAPE, AUX

1/2 and subgroups 1 - 2 and 3 - 4.

Phones/control room outputFig. 2.19:

(46) Connect your headphones or monitor speaker to the

PHONES/CTRL ROOM OUT 1/4" TRS connector.

IMPORTANT! High volume levels may damage your +

hearing and/or your headphones/loudspeakers. To

avoid switch-on/off thumps from the console and any

downstream devices, always make sure that the power

amp(s) or active speaker(s) are the last components that

are switched on and the rst to be switched off. Always

make sure that the appropriate volume is set.

CD/tape2.7

CD/tapeFig. 2.20:

(47) TO MAIN controls the volume of, for example, a CD player

connected to the CD/tape input connectors (see (49)).

(48) When the STANDBY switch is pressed, all input channels

are muted. Only the CD/tape signal will be routed to the

main mix. In this way, you can prevent the microphones from

pickung up unwanted sounds or noise that would interfere

with CD playback during a break. The main mix and chan-

nel faders can remain in their normal positions while playing

back music from CD (using the CD/TAPE INPUTs (49)), so

you don’t lose your mix.

CD/tape connectorsFig. 2.21:

(49) The CD/TAPE INPUT RCA connectors are for the connection

of CD players, tape decks or other line-level sources. The

signal volume is adjusted with the TO MAIN control.

(50) The CD/TAPE OUTPUT RCA connectors provide the stereo

main mix signal to a tape deck or DAT recorder to record

your mix. The signal is taken pre-fader, so that it will not be

inuenced by the fader positions.

Master aux send 1 and 22.8

Master aux sendsFig. 2.22:

(51) These are the master AUX SEND controls 1 and 2 for ad-

justing the volume level sent to the corresponding aux send

connectors (see (52)). This way, you can control the mix of

all AUX 1 or AUX 2 signals of the input channels. The AUX

SEND section also has a SOLO switch.

Master aux send outputsFig. 2.23:

(52) Use the AUX SEND outputs 1 and 2 to take the masterAUX

SEND signals and route them to an external effects device

or your monitor speakers. Subsequently, you can return the

effect signal, e.g. via the STEREO FX RETURN inputs (see

(67)) or specic input channels.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Control elements and connections10

Graphic 9-band stereo equalizer2.9

The graphic stereo equalizerFig. 2.24:

(53) Your EURODESK is equipped with a graphic 9-band stereo

equalizer processing either the main or the AUX 1 signal.

Use the EQ to adapt the sound to the room acoustics.

(54) Use the EQ IN switch to switch the equalizer on. In this case,

the fader LEDs illuminate.

(55) With the MAIN/AUX 1 switch you can determine the signal

to be processed, either main or AUX 1.

(56) Press the FBQ IN switch to activate the FBQ Feedback

Detection System. The frequencies causing feedback are

indicated by the brightly lit fader LEDs, while all other LEDs

are darker. Simply lower the level of the brightly lit faders

until feedback disappears.

When the switch is in the “AUX 1” position (see + (55)),

the EQ fader LEDs show both the MAIN and the AUX

1 signal simultaneously. However, if feedback occurs

in one of the signals, those signals without feedback

will be faded out to enable clear identication of where

feedback is occurring. If the MAIN signal happens to be

the one carrying feedback, put the switch (55) to “MAIN”

and then use the 9-band EQ to remove the feedback.

Effects section2.10

The digital effects processorFig. 2.25:

(57) Here you will nd a list of all multi-effects presets (see also

chapter 3 “DIGITAL EFFECTS PROCESSOR”).

(58) The FX LED level meters show the effects processor’s

input signal. Be sure that the clip LED only illuminates with

signal peaks. If it is lit all the time, the effects processor is

overloading and hence producing unpleasant distortion.

(59) The EffeCt displays show the currently selected presets.

(60) This is the master FX 1 (or 2) SEND control for adjusting

the volume of all FX send signals at the correspondingFX

send jacks (see (66)) and at the inputs of the built-in effects

processor. Use it to control the master signal of allFX 1/FX

2 signals from the input channels. When neither of the FX

SEND controls is turned up, the effects processor will not

receive a signal.

(61) Turn the FX 1 (or FX 2) control to select an effects preset.

Then, push it briey to conrm your selection and activate

the new effect.

(62) The FX 1 (or 2) TO AUX 1 controls allow you to add the effect

signal from the built-in effects processor (FX1 or FX2) to the

AUX 1 monitor signal. Naturally, the effects processor must

be provided with an input signal (i.e. the FX controls in the

channel strips plus the FX SEND controls and the channel

faders must be turned up).

(63) This is the FX 1 (or 2) TO AUX 2 control adding the effect

signal from the effects processor to the AUX 2 monitor signal.

See (62) for further details.

(64) The FX 1 (or 2) TO MAIN control routes the effect signal

either to the main mix or the subgroups 1 and 2 (or 3 and 4),

depending on the position of the selector switch (see (65)).

When it is hard left, no effect signal will be audible. Here,

too, the FX controls in the channel strips plus theFX SEND

controls and the channel faders must be turned up.

(65) These selector switches route the effect signal to the main

mix or to the subgroups 1-2 or 3-4. If the MAIN/SUB switch

is not pressed, the effect signal is sent to the main mix and

the SUB 1/2 / SUB 3/4 switch below is inoperative. If the

upper switch is pressed (SUB), however, the lower switch

determines whether the effect signal is routed to subgroups

1 and 2 (SUB 1/2) or 3 and 4 (SUB 3/4).

FX send and return connectorsFig. 2.26:

(66) The FX SEND 1 and 2 connectors also provide the master FX

send signals, for example, to connect them to the inputs of an

external effects device. However, these are “dry” signals only

with no “effect signals” from the built-in effects processor!

(67) The Stereo FX RETURN inputs 1 and 2 return the effect

signals from external effects processors and add them to

the main mix.

Footswitch connectorsFig. 2.27:

(68) The FOOTSW(ITCH) connector allows you to connect a

standard dual footswitch to separately enable/disableFX 1 or

FX 2. The tip of the 1/4" plug controls FX 1, the ring controls

FX 2.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Digital effects processor 11

Rear panel2.11

The rear panel of the EURODESKFig. 2.28:

(69) Use the POWER switch to put the mixer into operation.

This switch should always be in the “Off” position when you

connect your unit to the mains.

Please note: The POWER switch does not fully discon- +

nect the unit from the mains. To disconnect the unit

from the mains, pull out the main cord plug or appli-

ance coupler. When installing the product, ensure the

plug or appliance coupler is readily operable. Unplug

the power cord when the unit is not used for prolonged

periods of time.

(70) With the PHANTOM switch you can activate the phantom

power supply for the XLR connectors of the mono channels

for condenser microphones. The +48 V-LED (37) illuminates

when phantom power is on. In most cases, dynamic micro-

phones can still be used as long as they are connected in

a balanced conguration. If in doubt, please contact the

manufacturer of your microphone!

(71) The mains connection is a standard IEC receptacle. An ap-

propriate power cord is supplied with the unit.

(72) FUSE HOLDER. Before connecting the unit to the mains,

ensure that the voltage setting matches your local voltage.

Blown fuses should only be replaced by fuses of the same

type and rating. Please also read the information given in

chapter 6 “SPECIFICATIONS”.

(73) SERIAL NUMBER.

Digital effects processor3.

List of all effects presetsFig. 3.1:

99 FIRST-CLASS PRESETS

Here is the list of all multi-effects presets. The built-in

effects processor offers you various standard effects

such as reverb, chorus, anger, delay and a variety

of combination effects from our renowned studio

effects processor VIRTUALIZER PRO DSP2024P.

Use theFX control on the channels and the FX SEND control to

supply the effects processor with signals. A built-in digital stereo

effects processor has the benet of no external wiring, thus re-

ducing the risk of ground loops or level differences. Handling is

therefore much easier.

PARALLEL FX

The effects presets 1 to 70 provide classic “add-to-mix” effects. So,

when you turn up the FX 1 (or 2) TO MAIN control, you create a

mix of the (dry) channel signal and the effect signal. The balance

between the two signals can be set with the FX send and FX 1/2

TO MAIN controls.

This also applies to adding effect signals to the AUX 1 (or 2) moni-

tor mix, with the exception that the mix here is adjusted with the

AUX 1 (or 2) control in the channel strip and the FX TO AUX 1 (or

2) potentiometer. Of course, the effects processor must receive

a signal from the channel using the FX 1 (or 2) control. Make

sure that the PRE switch in the corresponding channel strip(s) is

pressed. Otherwise, the AUX buses will be set post-fader making

the volume of the AUX monitor signal dependent on the position

of the channel fader(s).

INSERT FX (channel is muted)

Effects presets #71 and higher process the entire signal, unlike

the “add-to-mix” effects. When you use an insert preset, be sure

to separate the respective channel from all buses (SUB button

and MAIN button not pressed) and only route the effect signal to

the main mix (FX 1/2 control, FX SEND 1/2 control and FX TO

MAIN 1/2 control).

The channel fader of the corresponding channel remains +

active and governs (in combination with the FX controls)

the signal level sent to the built-in effects processors.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Wiring examples12

Wiring examples4.

Studio set-up4.1

The following wiring example shows a studio set-up for 4-track-recording: the drums are mixed down to two subgroups and then

routed via the subgroup outputs to two tracks of the multi-track recorder. The remaining two subgroups are used to record the guitar,

keyboard (stereo channel) and two vocal signals on the remaining two tracks. The four return paths from the recorder are connected

to four separate mono input channels on the EURODESK. The built-in compressor is used only for the bass, which is why this input

channel is separate from all buses (SUB and MAIN switch not pressed). The bass signal is directly routed from the built-in effects

processor to the respective subgroups (FX TO MAIN control). The MAIN/SUB switch in the FX1 section is pressed, but NOT the SUB

1/2 SUB 3/4 button.

Wiring the console for studio operationFig. 4.1:

Please make sure that none of the subgroup routing switches (1-2 and 3-4) is pressed in the channels connected to +

the recorder returns. Otherwise, a feedback loop will be created as soon as you start recording. Only press the MAIN

switch on these input channels, so that the tape return signals are routed to the main outs and Phones/CTRL room

outputs of the console.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Wiring examples 13

Live set-up4.2

Wiring the console for live operationFig. 4.2:

This example shows a classic live set-up. As in the studio example, four drum microphones, bass, keyboard (stereo channel), guitar

and two vocal microphones are connected. The four drum channels (kick drum, snare, overhead L, overhead R) are mixed down to

two subgroups and then routed to the main mix. This way, it is possible to conveniently control the volume of the entire drums in the

main mix with the two subgroup faders. The built-in compressor insert effect is used for the bass. The corresponding input channel is

separate from all buses and the bass signal is routed directly from the internal effects processor to the main mix bus. The MAIN/SUB

switch must not be pressed in this case and the position of the SUB 1/2 SUB 3/4 switch is irrelevant.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Audio connectors14

Audio connectors5.

The inputs and outputs of the BEHRINGER EURODESK are

designed as unbalanced 1/4" TS connectors—except for the bal-

anced line inputs of the mono and stereo channels and the main

out connectors. Of course, all inputs and outputs work with both

balanced and unbalanced connectors. The tape ins and outs are

stereo RCA connectors.

Please ensure that only qualied personnel install and +

operate the EURODESK. During installation and opera-

tion, the user must have sufcient electrical contact to

earth. Electrostatic charges might affect the operation

of the unit.

¼" TS connectorFig. 5.1:

¼" TRS connectorFig. 5.2:

RCA cableFig. 5.3:

XLR connectorsFig. 5.4:

¼" TS footswitch connectorFig. 5.5:

¼" TRS connector for headphonesFig. 5.6:

Insert send and return ¼" TRS connectorFig. 5.7:

EURODESK SL3242FX-PRO/SL2442FX-PRO

Presets 15

Presets6.

Effect Description Application examples

PARALLEL EFFECTS

Cathedral Very dense and long reverberation of a large cathedral. Solo instruments / vocals in slow pieces.

Plate Simulates the sound of early plate reverberators. A classic for drums (snare) and vocals.

Concert Simulates a small theater or large concert hall. Creates an "atmosphere" (e.g. radioplay voices).

Stage Very dense reverb, especially for live applications. Dissipates the sound of keyboard pads, for example.

Room You can clearly hear the walls of the room. Reverb effect that isn't directly noticeable.

Studio

Adds spaciousness to the sound; signals sound natural, not

"at".

Gives a sound source more "class" in the mix.

Small Hall Simulates a small, lively (strongly reecting) hall. Perfect for processing drums.

Ambience Reproduces a middle-sized room without late reections. Extremely versatile effect.

Early Reections Very dense reverb with pronounced early reections. Drums, percussion, slap bass

Spring Reverb Simulates a classic spring reverberation. Extremely versatile effect.

Gated Reverb Reverb that is synthetically cut off Produces a very "crisp" snare sound.

Reverse Reverb Reverb with reversed envelope, i.e. it slowly gets louder. Produces a very spaced out vocal sound.

Chorus Slight detuning of the original signal.

Extremely versatile effect (guitar, vocals, bass, key-

boards etc.).

Flanger

A slightly delayed signal is added to the original signal,

producing phase shifting of the signals.

Extremely versatile effect (guitar, vocals, bass, key-

boards etc.).

Phaser Another phase-shift effect.

Extremely versatile effect (guitar, vocals, bass, key-

boards etc.).

Rotary Speaker Simulation of a classic effect for electronic organ. Organ / keyboards.

Delay Delay of the input signal with several repetitions. Extremely versatile effect.

Chorus & Reverb Combination of chorus and reverb. A classic effect for vocals.

Flanger & Reverb Flanger combined with a reverb effect. All-purpose effect.

Phaser & Reverb Phaser combined with a reverb effect. All-purpose effect.

Rotary Speaker &

Reverb

Rotary Speaker effect combined with reverb. Organ/keyboards/electric guitar.

Delay & Reverb Delay combined with reverb.

The most common combination for vocals, solo guitar,

etc.

Delay & Chorus

Widens the signals and produces interesting repetition

effects.

Makes vocals stand out in the mix. Good intelligibility is

preserved.

Delay & Flanger

Similar to Delay & Chorus, but with audible up/downward

modulation.

Ideal for creating a slightly spaced out sound.

INSERT EFFECTS

Compressor

Soft or loud passages are raised or lowered in level

respectively.

Single signals, especially from microphones.

Expander

No dynamics limitation (see Compressor), but quite the op-

posite: interference (noise, hum, etc.) is reduced in level.

Single signals, especially from microphones.

Gate

A gate opens for a specic period of time to make a specic

signal pass, and then closes abruptly.

"Controls" feedback-prone microphones / eliminates

interference.

Ultramizer

Extremely efcient compression through automatic adapta-

tion of compression parameters.

Gives mix signals a constant output level.

Ultrabass

Combines sub-harmonics processor, bass exciter and

limiter.

Gives keyboard sounds some special "class" / sound

effect for electric basses.

Panner The signal "wanders" between the sides of the stereo basis. Special effect, e.g. for radioplay soundtracking.

Exciter

Adds synthetic harmonics to the signal, resulting in in-

creased presence and "loudness".

Both mix and single signals. Improves intelligibility of

vocal signals.

Auto Filter

Level-dependent boost of a specic frequency band, similar

to auto-wah effect for electric guitars.

DJ-ing / sound effects for live events / electric guitar or

bass.

Tube Distortion Simulates the tube distortion of classic guitar ampliers. Electric guitar / vocals / keyboards.

Guitar Amp Guitar amp simulation. Electric guitar or bass.

Vinylizer Adds the clicks and noise of old vinyl records. DJ-ing / sound effects for live events.

Test Tone 1-kHz test tone. Makes P.A. level setting easier.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Specications16

Specications7.

Mono inputs

Microphone inputs (IMP “Invisible” Mic Preamp)

Type XLR connector, electronically balanced,

discrete input circuit

Mic E.I.N.

(20 Hz - 20 kHz)

@ 0 Ω source resistance -134 dB / 135.7 dB A-weighted

@ 50 Ω source resistance -131 dB / 134 dB A-weighted

@ 150 Ω source resistance -129 dB / 130.5 dB A-weighted

Frequency response

<10 Hz - 160 kHz -1 dB

<10 Hz - 200 kHz -3 dB

Gain range +10 dB to +60 dB

Max. input level +12 dBu @ +10 dB GAIN

Impedance approx. 2.6 kΩ balanced

Signal-to-noise ratio 110 dB / 112 dB A-weighted (0 dBu In @

+22 dB GAIN)

Distortion (THD+N) 0.004 % / 0.003 % A-weighted

Line input

Type ¼" TRS jack, electronically balanced

Impedance approx. 20 kΩ balanced, approx. 10 kΩ

unbalanced

Gain range -10 dB to +40 dB

Max. input level +22 dBu @ 0 dB GAIN

Fade-out attenuation

(Crosstalk attenuation)

Main fader closed 90 dB

Channel muted 84 dB

Channel fader muted 85 dB

Frequency response (Mic In → Main Out)

<10 Hz - 70 kHz +0 dB / -1 dB

<10 Hz - 130 kHz +0 dB / -3 dB

Stereo inputs

Type 2 x ¼" TRS jack, balanced

Impedance approx. 20 kΩ balanced, 10 kΩ

unbalanced

Gain range -20 dB to +20 dB

Max. input level +22 dBu @ 0 dB GAIN

CD/Tape in

Type RCA connector

Impedance approx. 10 kΩ

Max. input level +22 dBu

Equalizer

EQ mono channels

LOW 80 Hz / ±15 dB

MID 100 Hz - 8 kHz / ±15 dB

HIGH 12 kHz / ±15 dB

LOW CUT 80 Hz, 18 dB/oct.

EQ stereo channels

LOW 80 Hz / ±15 dB

LOW MID 400 Hz / ±15 dB

HIGH MID 3 kHz / ±15 dB

HIGH 12 kHz / ±15 dB

Channel inserts

Type ¼" TRS jack, unbalanced

Max. input level +22 dBu

AUX/FX Send

Type ¼" mono jack, unbalanced

Impedance approx. 120 Ω

Max. output level +22 dBu

FX Returns

Type ¼" mono jack, unbalanced

Impedance approx. 10 kΩ

Max. input level +22 dBu

Subgroup outputs

Type ¼" mono jack, unbalanced

Impedance approx. 120 Ω

Max. output level +22 dBu

Main outputs (XLR)

Type XLR connector, electronically balanced

Impedance approx. 240 Ω balanced, 120 Ω

unbalanced

Max. output level +28 dBu

Main outputs (¼")

Type ¼" TRS jack, electronically balanced

Impedance approx. 240 Ω balanced, 120 Ω

unbalanced

Max. output level +28 dBu

Main Inserts

Type ¼" TRS jack, unbalanced

Max. input level +22 dBu

Mono output

Type ¼" mono jack, unbalanced

Impedance approx. 120 Ω

Max. output level +22 dBu

Low pass variable30 Hz to 200 Hz, 18 dB/oct.

Phones/CTRL room output

Type ¼" TRS jack, unbalanced

Max. output level +19 dBu / 150 Ω (+25 dBm)

CD/Tape Out

Type RCA connector

Impedance approx. 1 kΩ

Max. output level +22 dBu

DSP

Type Texas Instruments

Converter 24-bit delta-sigma, 64/128-times

oversampling

Sampling rate 46 kHz

Main mix system data

(Noise)

Main mix @ -∞, channel fader @ -∞ -100 dB / -102.5 dB

A-weighted

Main mix @ 0 dB, channel fader @ -∞ -82 dB / -85 dB A-weighted

Main mix @ 0 dB, channel fader @ 0 dB -72 dB / -75 dB A-weighted

Power supply

Power consumption 50 W

Fuse (100 - 240 V~, 50/60 Hz) T 2.0 A H 250 V

Mains connector Standard IEC receptacle

Physical/weight

SL3242FX-PRO

Dimensions (H x W x D) 3.9" x 35.3" x 16.1" (100 mm x 896 mm

x 410 mm)

Weight (net) 25.4 lbs (11.5 kg)

SL2442FX-PRO

Dimensions (H x W x D) 3.9" x 26.9" x 16.1" (100 mm x 682 mm

x 410 mm)

Weight (net) 18.8 lbs (8.5 kg)

Equivalent Input Noise

Measuring conditions: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output;

unity gain.

20 Hz - 20 kHz; measured at main output. Channels 1 - 4 unity gain; EQ at; all chan-

nels on main mix; channels 1/3 as far left as possible; channels 2/4 as far right as

possible; reference = +6 dBu.

BEHRINGER is constantly striving to maintain the highest professional standards.

As a result of these efforts, modications may be made from time to time to existing

products without prior notice. Specications and appearance may differ from those

listed or illustrated.

EURODESK SL3242FX-PRO/SL2442FX-PRO

Warranty 17

Warranty 8.

Other warranty rights and national law § 1

1. This warranty does not exclude or limit the buyer’s statutory rights

provided by national law, in particular, any such rights against the seller

that arise from a legally effective purchase contract.

2. The warranty regulations mentioned herein are applicable unless

they constitute an infringement of national warranty law.

Online registration § 2

Please do remember to register your new BEHRINGER equipment right

after your purchase by visiting http://www.behringer.com and kindly

read the terms and conditions of our warranty carefully. Registering

your purchase and equipment with us helps us process your repair

claims quicker and more efciently.

Thank you for your cooperation!

Warranty § 3

1. BEHRINGER (BEHRINGER International GmbH including all

BEHRINGER subsidiaries, except BEHRINGER Japan) warrants

the mechanical and electronic components of this product to be free

of defects in material and workmanship for a period of one (1) year*

from the original date of purchase, in accordance with the warranty

regulations described below. If the product shows any defects within

the specied warranty period that are not excluded from this warranty

as described under § 5, BEHRINGER shall, at its discretion, either

replace the product by providing a new or reconditioned product or

repair the product using suitable new or reconditioned parts. In the

case that other parts are used which constitute an improvement,

BEHRINGER may, at its discretion, charge the customer for the ad-

ditional cost of these parts. In case BEHRINGER decides to replace

the product, this warranty shall apply to the replacement product for

the remaining initial warranty period, i.e one year* from the date of

purchase of the initial product.

2. If the warranty claim proves to be justied, the product will be

returned to the user freight prepaid.

3. Warranty claims other than those indicated above are expressly

excluded.

Return authorization number § 4

1. To obtain warranty service, the buyer (or his authorized dealer) must

call BEHRINGER during normal business hours BEFORE returning

the product. All inquiries must be accompanied by a description of

the problem. The buyer or his authorized dealer will receive a return

authorization number.

2. Subsequently, the product must be returned in its original shipping

carton, together with the return authorization number. The return ship-

ment address will be indicated by BEHRINGER.

3. Shipments without freight prepaid will not be accepted.

Warranty regulations§ 5

1. Warranty services will be furnished only if the product is accom-

panied by a copy of the original retail dealer’s invoice. Any product

deemed eligible for repair or replacement under the terms of this war-

ranty will be repaired or replaced.

2. If the product needs to be modied or adapted in order to comply

with applicable technical or safety standards on a national or local

level, in any country which is not the country for which the product was

originally developed and manufactured, this modication/adaptation

shall not be considered a defect in materials or workmanship. The

warranty does not cover any such modication/adaptation, irrespec-

tive of whether it was carried out properly or not. Under the terms of

this warranty, BEHRINGER shall not be held responsible for any cost

resulting from such a modication/adaptation.

3. Free inspections and maintenance/repair work are expressly ex-

cluded from this warranty, in particular, if caused by improper handling

of the product by the user. This also applies to defects caused by nor-

mal wear and tear, in particular, of faders, crossfaders, potentiometers,

keys/buttons, tubes, guitar strings, illuminants and similar parts.

4. Damage/defects caused by the following conditions are not covered

by this warranty:

improper handling, neglect or failure to operate the unit in =

compliance with the instructions given in BEHRINGER user

or service manuals.

connection or operation of the unit in any way that does not =

comply with the technical or safety regulations applicable in

the country where the product is used.

damage/defects caused by force majeure or any other condition =

that is beyond the control of BEHRINGER.

5. Any repair or opening of the unit carried out by unauthorized per-

sonnel (user included) will void the warranty.

6. If an inspection of the product by BEHRINGER shows that the

defect in question is not covered by the warranty,

7. Products which do not meet the terms of this warranty will be re-

paired exclusively at the buyer’s expense. BEHRINGER will inform the

buyer of any such circumstance. If the buyer fails to submit a written

repair order within 6 weeks after notication, BEHRINGER will return

the unit. Costs for freight and packing will be invoiced separately

C.O.D. When the buyer has sent in a written repair order such costs

will also be invoiced separately.

Warranty transferability§ 6

This warranty is extended exclusively to the original buyer (customer of

retail dealer) and is not transferable to anyone who may subsequently

purchase this product. No other person (retail dealer, etc.) shall be

entitled to give any warranty promise on behalf of BEHRINGER.

Claim for damages§ 7

Failure of BEHRINGER to provide proper warranty service shall not

entitle the buyer to claim (consequential) damages. In no event shall

the liability of BEHRINGER exceed the invoiced value of the product.

* Customers in the European Union please contact BEHRINGER

Germany Support for further details.

Technical specications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. All

trademarks (except BEHRINGER, the BEHRINGER logo, JUST LISTEN and ULTRABASS) mentioned belong to their respective owners, and such

use neither constitutes a claim of the trademarks by BEHRINGER nor afliation of the trademark owners with BEHRINGER. BEHRINGER accepts no

liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained

herein. Colors and specications may vary slightly from product. Our Products are sold through authorized dealers only. Distributors and dealers are

not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. This manual

is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying

and recording of any kind, for any purpose, without the express written permission of BEHRINGER International GmbH.

+49 2154 9206 0, Fax +49 2154 9206 4903

Behringer Eurodesk SL3242FX-Pro User manual

Brand: Behringer

Model: Eurodesk SL3242FX-Pro

Category: Musical Instruments

Type: User manual

This manual is also suitable for

Download PDF

report

Behringer Eurodesk SL3242FX-Pro User manual

This manual is also suitable for

Behringer Eurodesk SL3242FX-Pro User manual

Related papers

Other documents