Netcomm IG6000 User manual

Netcomm
Brand
Netcomm
Model
IG6000
Category
Networking
Type
User manual
IndustrialModem
Designedforunattendedsites
· Designedtosurviveharshenvironmentalconditionsforunattendedoperation,
suchasremotemonitoring.
· DualWatchdogTimerswhichcanrestartthemodemifthemodemcrashes,starts
executinginvalidcodeorhasapowerinterruption.
· Fullycustomisable.
· Auniquevoicemessagingsystemthatcanbeusedasavoicemailboxor
answeringmachine.
· Dial&TalkAlarmfeature.
· AutomaticPowerOffwhenmodemisnotused.
· Nointernalbatteriesfornonvolatilestorageensuringalonglife.
· Smallruggedpackaging.
IndustrialModemUserGuide
YML3913A 2
TableofContents
ContactInformation..................................................................................................................................................3
TechnicalSupport.............................................................................................................................................3
TeleMarketing ..................................................................................................................................................3
MailingList......................................................................................................................................................3
Legal&RegulatoryInformation ...............................................................................................................................4
CopyrightInformation ..........................................................................................................................................4
AustralianCustomerInformation ..........................................................................................................................4
NewZealandCustomerInformation......................................................................................................................4
Introduction..............................................................................................................................................................6
ModemControlsandIndicators ................................................................................................................................7
Links(Internalcontrols)........................................................................................................................................7
LEDS ...................................................................................................................................................................7
ModemFeatures.......................................................................................................................................................8
PowerDownFeature ............................................................................................................................................8
DialandTalkFeature............................................................................................................................................8
VoiceMessagingSystem ......................................................................................................................................9
HowtoLoadtheVoiceAlarmMessages...............................................................................................................9
RemoteVoiceSettingofAlarmMessages.............................................................................................................10
OperatingModes......................................................................................................................................................11
AsynchronousMode.............................................................................................................................................11
LineSpeeds ......................................................................................................................................................11
SynchronousMode1 ............................................................................................................................................11
LeasedLineOperation..........................................................................................................................................12
ModemATCommands ............................................................................................................................................13
Commands ...........................................................................................................................................................13
DialModifiers ..................................................................................................................................................13
GeneralCommands...........................................................................................................................................14
ModulationSetting ...........................................................................................................................................18
DistinctiveRing................................................................................................................................................19
ResponseCodes....................................................................................................................................................20
SRegisters ...........................................................................................................................................................21
Specifications...........................................................................................................................................................22
Dimensions.......................................................................................................................................................22
Communications...............................................................................................................................................22
TerminalSpeeds ...............................................................................................................................................22
Power ...............................................................................................................................................................22
CallerID...........................................................................................................................................................22
CommandSets..................................................................................................................................................22
DataFormats ....................................................................................................................................................22
FlowControl.....................................................................................................................................................22
DataCompression.............................................................................................................................................23
Encryption........................................................................................................................................................23
Environmental ..................................................................................................................................................23
Humidity ..........................................................................................................................................................23
BuildOptions ...................................................................................................................................................23
IndustrialModemUserGuide
YML3913A 3
ContactInformation
PleasecontactNetCommforhelp,information,salesenquiriesortojointheNetCommInfoMailingList:
Technical Support
WebPage: http://www.netcomm.com.au
Phone: (02)98702332
Fax: (02)98702619
TeleMarketing
Phone: (02)94242056
Fax: (02)94242525
MailingList
Forthelatestsalesandtechnicalinformation,subscribetotheNetCommInfoMailingListbysendinganemailto:
mailinglist@netcomm.com.au
Inthebodyofthemessageentertheword:
subscribe
ThiswilladdyouremailaddresstotheNetCommInformationMailingListandyouwillbeemailednewsand
updatesregularly.
IndustrialModemUserGuide
YML3913A 4
Legal&RegulatoryInformation
CopyrightInformation
Thismanualiscopyright.Apartfromanyfairdealingforthepurposesofprivatestudy,research,criticismor
review,aspermittedundertheCopyrightAct,nopartmaybereproduced,storedinaretrievalsystemor
transmittedinanyform,byanymeans,beitelectronic,mechanical,recordingorotherwise,withouttheprior
writtenpermissionofNetCommLimited.
NetCommLimitedacceptsnoliabilityorresponsibility,forconsequencesarisingfromtheuseofthisproduct.
NetCommlimitedreservestherighttochangethespecificationsandoperatingdetailsofthisproductwithout
notice.
NetCommisaregisteredtrademarkofNetCommLimited.
Allothertrademarksareacknowledgedthepropertyoftheirrespectiveowners.
AustralianCustomerInformation
Austel(TheAustralianTelecommunicationsAuthority)requiresyoutobeawareofthefollowinginformationand
warnings:
Usersmayexperienceminoraudiodistortionwhenusingthisproduct.Thisdistortionmaybegeneratedbythelow
bitrateforvoicesampling.
SomeofthemodemdefaultsettingshavebeenselectedtocomplywithAusteltechnicalspecifications.Ifyou
intendtochangeanydefaultsettingsyoumustcomplywiththefollowingrules:
1. Themodemmustnotansweranincomingcalllessthantwosecondsafterthefirstringsignal.AsaÒruleof
thumbÓyourmodemshouldbesetsoitanswersincomingcallsafterthesecondring(ATS0=2).
2. IfBusy signaldetectionisswitchedoff,themodemmustnotattemptmorethantwoautomaticredialsand
mustwaitatleasttwosecondsbeforeredialling.
3. IfBusysignaldetectionisswitchedon,themodemmustnotattemptmorethannineautomaticredialsand
mustwaitatleasttwosecondsbeforeredialling.
4. If,afterrediallingthemaximumnumberoftimes,themodemisstillunabletoestablishaconnectionyoumust
wait30minutesbeforeattemptingtoredial.
5. TheuseofBellstandard103and212AisnotpermittedinAustralia.Useofthesemodeswillcauseyour
modemtoloseitspermitstatus.
Changingthedefaultvaluesofthemodem,insuchawayastocauseyourmodemtooperateinanoncompliant
mannerwhenconnectedtoatelecommunicationsnetworkoperatedbyacarrier,iscontrarytothe
TelecommunicationsAct1991andmayresultinpenaltiesof$12,000.
NewZealandCustomerInformation
NewZealandTelecomrequiresyoutobeawareoftheseimportantwarnings:
Thisequipmentmaynotnecessarilyprovidefortheeffectivehandoverofacalltoorfromatelephoneconnected
tothesameline.
Theoperationofthisequipmentonthesamelineastelephonesorotherequipmentwithaudiblewarningdevicesor
automaticringdetectorswillgiverisetobelltinkleornoiseandmaycausefalsetrippingoftheringdetector.
Shouldsuchproblemsoccur,theuserisnottocontactTelecomFaultsService.
ThetelephoneassociatedwiththeauthorisedapparatusmustbepermittedforconnectiontotheNewZealand
publictelephonenetwork.
Thetransmitlevelfromthisdeviceissetatafixedlevelandbecauseofthistheremaybecircumstanceswherethe
devicedoesnotgiveitsoptimumperformance. Beforereportingsuchoccurrencesasfaults,pleasechecktheline
withastandardTelepermittedtelephone,anddonotreportafaultunlessthetelephoneperformanceisimpaired.
IndustrialModemUserGuide
YML3913A 5
Ifyourmodemeversuffersphysicaldamagethatcausesitsinternalpartsto becomeexposed,itshouldbe
disconnectedfromthephonelineimmediately.Themodemmustthenberepairedbeforereconnectiontothephone
lineispermissible.
Shoulditbenecessarytophysicallymoveyourmodem,disconnectitfromthephonelineorearthingleadbefore
disconnectingthepowerconnection.Whenreconnectingyourmodem,reconnectthepowerorearthingleadbefore
reconnectingittothephoneline.
SomeparametersrequiredforcompliancewithTelecomÕsPTCSpecificationsaredependentontheequipment
connectedtotheRS232port.Theconnectedequipmentshallbesettooperatewithinthefollowinglimitsfor
compliancewithTelecomSpecifications:
1. EquipmentconnectedtotheRS232portshallbecertifiedtomeettherequirementsofReg.18oftheNew
ZealandWiringRegulations1976.
2. Whentheusermanuallyinitiatesacall,viaequipmentconnectedtotheRS232port,theequipmentshall
operatewithinthefollowingrestrictions:
a. Notmorethan5callattemptsshallbemadetothesamenumberwithinaonehourperiod.
b. Thereshallbeatleast60secondsbetweencallattempts.
c. Notmorethanatotalof10callattemptsshallbemadetothesamenumberforanysinglemanualcall
initiation.
d. Automaticcallstodifferentnumbersshallbenotlessthan5secondsapart.
FAILURETOMEETTHEABOVEREQUIREMENTSMAYNEGATETHEUSERRIGHTSUNDERTHE
TELECOMTERMSOFSERVICE.
WhenoperatinginV.22bisorV.22modeoversomeoldertelephoneexchanges,itmaybenecessarytoissuethe
&G2command.
SettingtheS0register(autoanswer)toS0=1ortovaluesgreaterthan5willrenderthisequipmentnoncompliant
withtheTelepermitrequirements.
ThisequipmentdoesnotprovideaguardtonewiththeV.22andV.22bisanswermodes.Insomecircumstances
thiscouldcauseinterferencewiththetelephonenetworksignallingsystems,andcouldresultinlostcalls.Telecom
willnotacceptresponsibilityshouldsuchproblemsoccur.Suchoccurrenceswillberare.
ThepreferredmethodistouseDTMFtones(ATDT...)asthisisfasterthanpulse(decadic)dialling,andis
availableonmostNewZealandtelephoneexchanges.WhereDTMFisnotavailableanddecadicmustbeused,
yourcommunicationssoftwaremustbesetuptorecordnumbersaccordingtothefollowingtranslationtableasthe
modemisnotdirectlycompatiblewiththeNewZealand(10N)Reversediallingstandard.
Numbertobedialled Numbertoprogramintocomputer
0 0
1 9
2 8
3 7
4 6
5 5
6 4
7 3
8 2
9 1
NotethatwhereDTMFdiallingisused,thenumbersshouldbeenterednormally.
IndustrialModemUserGuide
YML3913A 6
Introduction
ThismanualprovidesabriefintroductiontotheIndustrialSmartModemandgivesanoverviewofthefeaturesand
commandsavailable.
The IG6000IndustrialSmartModemhasaSmartModem336corewithadditionalfeaturesthatmakeitsuitablefor
industrialandunattendedoperation.Particularattentionhasbeenpaidtoensuringthatthemodemrestartsreliably
intheeventofpowerinterruptionorinternalmalfunction.ThemodemusesthelatestgenerationRockwellDSP
whichwillenablenewfeaturestobesoftuploadablewhentheybecomeavailable.
IndustrialModemUserGuide
YML3913A 7
ModemControlsandIndicators
Links(Internalcontrols)
LK1 1 Setfactorydefaults
2 Normal
LK2 1 Reserved
LK3 1 Reserved
LK4 1 Reserved
LK5 Reserved
LK6 Reserved
LK7 Reserved
LK8 1 Powerdowndisabled
2 DTRwakeupenabled
None DTRwakeupdisabled
LK9 LinkconnectsRS232shieldtoground
PSTN IN PSTN
OUT LeasedLine
LEDS
DCDDataCarrierDetect(InnerLED)
LEDwillglowwhenthemodemdetectsavalidcarriersignalfromaremotemodem.
PWRPower (OuterLED)
LEDwillglowtoindicatewhenthemodemisturnedon.LEDwillbeoffwhenthemodemisinpowerdown
mode.
IndustrialModemUserGuide
YML3913A 8
ModemFeatures
PowerDownFeature
S119canbesetwiththenumberofsecondsofnoactivitybeforethemodemshutsdown.Themodemwillnotshut
downifDTRisasserted,ifthemodemisconnected,anykeyonthekeyboardispressedoranalarmswitchison.
Themodemwillwakeupif:
· DTRisraised
· thereisaRingingsignalor
· analarmswitchisasserted.
S119defaultsto0(powerdowndisabled).
Themodemdrawsalmostnopowerwhenpowereddown.
DialandT alkF eature
Thisfeatureenablesamodemtoalert,byspokenword,thatanalarmsituationataremotesiteneedsattention.The
modemscanbeconfiguredtodialupto10presetnumbersandspeakastoredmessagewhenoneoftwoexternal
switchesareclosed.
Theseswitcheswillconnecttopins12and7(alarm1)andpins13and7(alarm2)oftheRS232connector. An
alarmconditionisrecognisedwhenashortcircuitisappliedacrosseitherpairofpins,egbyuseofarelay.
Bydefaulttomodemwillringstorednumber0ifeitheralarmswitchisclosed.
Tosetstorednumber0type:
AT&Z0=nnnnnnnnnnwherennnnnnnnisthephonenumber.
Youmaystoreupto10numbersusing&Z0to&Z9.
ThenumberstoringforeachalarmcanbespecifiedbytheAT#ALMcommand:
AT#ALM1=1,4,8,3
Meansthanifalarmswitch1ispressedthemodemshouldringthestorednumbers1then4then8then3.
AT#ALM2=9
Meansthatifalarmswitch2ispresseddialstorednumber9.
IndustrialModemUserGuide
YML3913A 9
VoiceM essagingSystem
ThisfeaturecanbeinstalledintoanIG6000bydownloadingavocabularyfiletothemodemtoenableittorespond
toDTMFtonesfromaremotemodem.
Ifthisfeatureisenabledbyusingthe#MEMcommand:
AT#MEM1 ModemwillanswerinvoicemodeafterS110ringsifDTRislow
AT#MEM2 ModemwillanswerinvoicemodeafterS110ringsregardlessofDTR
AT#MEM0 Allvoicefeaturesoff
Dialthemodemandwaitforittoanswer.AfterthenumberofringsspecifiedbyS110(default4)themodemwill
answerthecallandrespondwith"LeaveaMessageaftertheBeep".IfyoukeyinaDTMFdigitduringthetime
thismessageisplayed,themessagewillstopandyoucancompleteenteringthePINnumber.Thefactorydefault
PINnumberis1234.Thiscanbechangedbyusingthenew#PINcommand.
AT#PINnn…nnn
wherenn…nnnisthepinnumber.Upto10digitsofPINnumbercanbespecified
IfyoukeyinthecorrectPINnumberthemodemwillsay"OK"andaskforacommand.Youmaykeyin0fora
menuofavailablefunctions.
FunctionsAvailableusingDTMFkeys
19 Playbackstoredmessage1to20
*1 Recordanewwelcomemessagetoreplace"LeaveaMessageaftertheBeep"
*2 Recordanewmessage
*3 Playbackthecurrentwelcomemessage
*4 Reportnumberofstoredmessagesandthestateofthealarmswitches(ONorOFF)
*5 Playallmessages
*6 Enable/disableansweringmachinerecordfunction
*9 Erasestoredmessagesbutretainthewelcomemessage
*0 Eraseallstoredmessagesincludingthewelcomemessage(returntofactorydefaultmessage)
## Hangup
Messages1and2areusedbythealarmswitches.Othermessagescanbestoredandusedasavoicemailbox
whichcanbesharedbyagroupofpeoplewhoknowthePINnumber.
Ifnopinnumberisenteredtheusercanleaveamessageafterthewelcomemessagebeep.
+ Toavoidrecordingalotofsilencethemessagescanbeterminatedwiththe#DTMFkey.
About8minutesofvoicestorageinamaximumof20individualmessagesisavailable.
HowtoLoadtheVoiceAlarmMessages
Ifyouhavenotdownloadedavocabularyfileusethefollowingprocedure:
1. ConnectthemodemtoaPCrunningaterminalprogram(likeHyperterm).
2. TypeATS119=0tostopmodemgoingtosleep.
3. TypeAT#MINIandwaitforEPROMstoerase.Themodemwillbeepwhenready.
4. TypeAT#MEM2toputthemodemintovoiceansweringmode.
5. Connectmodemtophonelineandusingatouchtonephonedialthemodem.Themodemwillanswer
withabriefmessage"Leaveamessageafterthebeep!"
6. RecordyourmessageintothemodemforAlarmCondition#1,leaving2secondsofsilenceafterthebeep
beforespeaking.
IndustrialModemUserGuide
YML3913A 10
7. Pressthe#buttononthephonewhenyourmessageisfinished.
8. Hangupthephonewaitafewseconds.
9. RingthemodemagainandrecordasecondmessageforAlarm#2followingsteps8and9.Your
messagesarenowrecorded.
10. ReconnectmodemtoaterminalprogramandtypeAT#MCDtodisplaythestoredmessages.Theduration
ofthe2messagesyouhaverecordedshouldbevisible.
11. IfyouwishthemodemtoanswercallsindatamodetypeAT#MEM0&Winaterminalprogramtoturn
offthevoiceansweringfunctionorAT#MEM1ifyouwantthevoiceansweringfunctiononlywhenDTR
islow.
Toredothemessages,erasetheEPROMsusingAT#MINIandrecordthemessagesagain.
RemoteVoiceSettingofAlarmMessages
Ifyouhaveinstalledthevocabularyfile,usetheproceduredetailedintheVOICEMESSAGINGSYSTEMtoenter
themodemPINnumberthenuseDTMFcommand*2therecordthefirstmessagethenenter*2againtoenterthe
secondmessage.Youmayplaybackthe messagesimmediatelybykeyingDTMF1andDTMF2toverifythatthey
soundOK.
Hangupbykeying##.
IndustrialModemUserGuide
YML3913A 11
Operating Modes
AsynchronousMode
AsynchronousModeisthenormaldefaultmodeofthemodem.Control andmonitoringisperformedbyexecuting
theATcommandsusingaPCfittedwithsuitablecommunicationssoftware.
SynchronousOperation
Yourmodemsupportstwosynchronousmodes.Mode1allowsoperationwithcomputerswhichsupport
asynchronousandsynchronouscommunicationonasingleRS232port.Mode2allowsyourmodemtobe
operatedwithdedicatedsynchronousterminals.
Althoughyourmodemcanonlyoperateoverasingletwowireconnection,itwillstillperformfullduplex
synchronouscommunication.HalfduplexoperationcouldbesimulatedbycontrollingthestateoftheRTSand
CTSsignals.
TerminalSpeeds
Yoursynchronousterminalorhostshouldusetheclocksignalsprovidedbythemodemtosynchronisetransmit
andreceivedata.Theclockspeedwillrepresenttheactualconnectionspeedofthemodem.
+ Whensynchronousmodeisselected,yourmodemcannotoperateinconstantspeedmodeorusetheerror
correctionordatacompressionfacilitiesofthemodem.Onlyvariablespeedmodeisavailable insynchronous
connections(thisreferstothemodem'sterminalspeed).
LineSpeeds
Yourmodemsupportsanumberofsynchronouslinespeeds.
Whenoperatinginsynchronousmode,yourmodemshouldalwaysbeconfiguredwithalocked,nonautoranging
Bsetting(thisreferstomodemlinespeed).
ForV.34,theBsettingonlysetsthemaximumspeed.Themodemwillautomaticallydeterminethehighestusable
speedfortheline.
SynchronousMode1
Synchronousmode1isselectedwiththe&M1command.
· Type:AT&M1<E>
Yourmodemwillentersynchronousmodewheneveritsuccessfullyconnectstoaremotemodem.
Youshouldalso:
· Type:AT&D2<E>
ThisallowshangupviayourcomputerÕsDTRsignal.
Toreturntoasynchronousoperation:
· Type:AT&M0<E>
SynchronousMode2
Synchronousmode2isselectedwiththe&M2command.
· Type:AT&M2<E>
Yourmodemwillentersynchronousmodewheneveritsuccessfullyconnectstoaremotemodem.
Youshould also:
· Type:AT&D2<E>
Thisallowsyoutodialandhangup.
IndustrialModemUserGuide
YML3913A 12
WhentheterminalassertstheDTRsignal(DTRmakesanOFFONtransition),yourmodemwilldialstoredphone
numberzero.Thephonenumbermaycontaindialmodifiers.
Toreturntoasynchronousmode:
· Type:AT&M0<E>
Yourmodemwillremaininasynchronousmode.
LeasedLineOperation
Aleasedline,orprivateline,isatelephonelinethatpermanentlyconnectstwoormorelocations.Theleasedline
doesnothaveanyswitchingequipmentassociatedwithit.
Leasedlineoperationwiththemodemisselectedwiththe&Lcommand.
Ifyouselectleasedlineoperationwiththe&L1command,youmustissuetheATAcommandtoansweracall,and
theATDcommandtoinitiate acall.
Ifyouuse&L2or&L3toselectAutoleasedlineoperation,youdonotneedtoissuetheATAorATDcommands;
&L2selectsOriginatemodeautomaticallyand&L3selectsAnswermodeautomatically.Todialoranswer,raise
DTR;tohangupandreturntolocalcommandstate,lowerDTR.
+ Youwillrequireaspecialphonecable(availablefromyourdealer)toconnectyourmodemtoaleased
linesocket.Thephonecablesuppliedwithyourmodemissuitableforusewithnormal,dialup,voice(PSTN)
lines.
Beforecommencingleasedlinecommunications,itisrecommendedthatanonautorangingBsettingbespecified.
+ Iferrorcorrectionisrequired,selectaReliablemode,notanAutoReliablemode.(Seethe \Ncommand.)
Autorangingandfallbackaredisabledinleasedlinemode.Yourmodemwillonlyattempttoconnectusingthe
communicationsstandardspecifiedbytheBcommandandtheterminalspeed.
Onceaconnectionhasbeenestablished,ifyourmodemdetectsalossofcarrieritwillcontinuouslyattempttore
establishtheconnection.
IfthemodemisinautoleasedlineoperationandthisconfigurationhasbenstoredinmemoryusingtheAT&W
command,atimeoutperiodof10secondsisavailableafterpoweruptodisabletheleasedlinemodeviatheAT&O
command.Alternatively,thiscommandcanbesentwithDTRlow.
IndustrialModemUserGuide
YML3913A 13
ModemATCommands
YourIndustrialModemªhasanumberofspecificcommandsthatcontrolandenhanceitsoperation.Toaccessand
changethesecommandsopenalocalterminalconnectionwithyourmodemusingyourpreferredcommunications
software,suchasWinFaxPro,andtypethelettersATfollowedbythespecificcommandandpress<Enter>.The
ATcommandsarecaseinsensitiveandmaybeenteredineitherlowerorcapitalletters.
n indicatesthedefaultsettings
Commands
Command Description
A Answercall
D Dialnumber
H Hangupmodem
O EnterOnlinestate
DialModifiers
DialDigits 09,A,B,C,D,#,*
, Pausewhiledialling
For^ Disablecallingtones
J InitiateMNP10at1200bps(V.22)
K MNP10cellularpowerleveladjustmentforthiscall
L Rediallastnumber
M InitiateMNP10at4800bps(V.32)
P Pulsedial number
R Switchtoanswermode
S=n DialstorednumberÔnÕ(wheren=09)
T Tonedialnumber
W Waitfordialtone
; ReturntoLocalcommandstate
! Hookflash
@ Waitforquietanswer
IndustrialModemUserGuide
YML3913A 14
Gener alCommands
+++ EscapeSequence
? Displayshelp.Maybefollowedbythecommand(s)orakeywordforwhich
helpisneeded
A/ RepeatCommand
B0 n AutoConnect
B1 AutoConnect
B2 AutoConnect
B3 V.21 300bps
B4 Bell103 300bps
B5 V.23 1200/75bps
B6 V.22 1200bps
B7 Bell212A 1200bps
B8 V.22bis 2400bps
B9 AutoConnect
B10 V.32 4800bps
B11 V.32bis 7200bps
B12 V.32(NonTCM) 9600bps
B13 V.32 9600bps
B14 V.32bis 12000bps
B15 V.32bis 14400bps
B16 V.34/V.FastClass 14400bps
B17 V.34/V.FastClass 16800bps
B18 V.34/V.FastClass 19200bps
B19 V.34/V.FastClass 21600bps
B20 V.34/V.FastClass 24000bps
B21 V.34/V.FastClass 26400bps
B22 V.34/V.FastClass 28800bps
B23 V.3431200bps
B24 V.3433600bps
E0 Localcommandstateechooff
E1 n Localcommandstateechoon
H0 Goonhook
H1 Gooffhook
I0 Numericfirmwareidentity
I1 Checksumoffirmware returnchecksum
I2 Checksumoffirmware returnOK/ERROR
I3 ModemModel
I4 FirmwareVersionanddate
I5 ManufacturerID
I9 Verbalfirmwareidentity
I10 Displaymodemstatistics
L0 Lowestvolumelevel
L1 Lowvolumelevel
L2 n Mediumvolumelevel
L3 Highestvolumelevel
M0 Speakerisalwaysoff
M1 n Speakeronwhenconnecting,offwhenconnected
M2 Speakeralwayson
M3 Speakeroffwhendiallingorafterconnectionestablished
IndustrialModemUserGuide
YML3913A 15
M4 Speakeronduringdial,answer,retrainorratechange
O1 EnterOnlinestateandforcecommunicationretrain(V.22bisandV.32bisonly)
O2 Retrain,donÕtgoonline(V.22bis&V.32bis)
O3 Changelinespeedto4800bps(V.32&V.32bis)
O4 Changelinespeedto7200bps(V.32&V.32bis)
O5 Changelinespeedto9600bps(V.32&V.32bis)
O6 Changelinespeedto12000bps(V.32&V.32bis)
O7 Changelinespeedto14400bps(V.32&V.32bis)
P Pulsedialling
Q0 n Modemreturnsresponsecodes
Q1 Modemdoesnotreturnresponsecodes
Q2 ModemdoesnotreturnRINGINGorresponsecodeswhenanswering
R9 9600bps(lockedterminalspeed noautobaud)
R14 14,400bps(lockedterminalspeed noautobaud)
R19 19,200bps(lockedterminalspeed noautobaud)
R28 28,800bps(lockedterminalspeed noautobaud)
R38 38,400bps(lockedterminalspeed noautobaud)
R57 57,600bps(lockedterminalspeed noautobaud)
R115 115,200bps(lockedterminalspeed noautobaud)
R230 230,400bps(lockedterminalspeed noautobaud)
Sn? DisplayvalueinSRegisterÔnÕ
Sn=x PlaceÔxÕinSRegisterÔnÕ
T n Tonedialling
V0 Numericresponsecodes
V1 n Verbal responsecodes
W0 CONNECTmessagereportstheterminalspeed
W1 CONNECTmessagereportstheterminalspeed
W2 n CONNECTmessagereportsthelinespeed
X0 Basicresponsecodes(codes04,8)
X1 Extendedresponsecodes(codes05,8,1012,3040,6062)
X2 Extendedresponsecodes(codes06,8,1012,3040,6062)
X3 Extendedresponsecodes(codes05,7,8,1012,3040,6062)
X4 Extendedresponsecodes(codes07,1012,3040,6062)
X5 n Extendedresponsecodes(codes07,1013,3040,6062)
X6 Extendedresponsecodes(codes05,78,1013,3040,6062)
Zn Restoreconfigurationprofilen(n=0,1,2,3)
&B0 8bitcharacterlength
&B1 9bitcharacterlength
&B2 10bitcharacterlength
&B3 11bitcharacterlength
&B4 n 10or11bitcharacterlengthdeterminedbyautobaud
&C0 DCDsignalalwaysasserted
&C1 n DCDsignalrespondstoremotemodem
&C2 DCDsignalalwayson,pulseslowondisconnect
&C3 DCDassertedduringvoicesession
&D0 IgnoreDTR
&D1 ReturntoLocalcommandstateifDTRgoeslow
&D2 n Hangup&returntoLocalComifDTRgoeslow,disableautoansweruntilDTR
asserted
&D3 Initialisewithvaluesin&YprofileifDTRgoeslow
&F0 Restorefactorydefaults
IndustrialModemUserGuide
YML3913A 16
&F1 Restorenonerrorcorrectionfactorydefaults
&F. Resetmodem(clearsecuritydatabase/Telephonenumbers)
&G0 n Noguardtonegenerated
&G1 550Hzguardtonegenerated
&G2 1800Hzguardtonegenerated
&K0 Flowcontroldisabled
&K3 RTS/CTSflowcontrol
&K4 XON/XOFFflowcontrol
&K5 TransparentXON/XOFFflowcontrol
&K9 n Failsafeflowcontrol
&M0 n Asynchronousmode
&N0 Abortdialcharacterdisabled
&N1 n Abortdialcharacterenabled
&P0 39/61make/breakratio(USA)
&P1 n 33/67make/breakratio(Aus/UK)
&S0 DSRsignalalwaysasserted
&S1 n DSRsignalassertedatstartofhandshake
&S2 DSRsignalassertedatendofhandshake(beforeCONNECTmessage)
&T0 Terminatecurrenttest
&T1 LocalAnalogueLoopbacktest
&T3 LocalDigitalLoopbacktest
&T4 n GrantRemoteDigitalLoopbacktest
&T5 DenyRemoteDigitalLoopbacktest
&T6 RemoteDigitalLoopbacktest
&T7 RemoteDigitalLoopbackwithSelftest
&T8 LocalAnalogLoopbackwithSelftest
&V Viewactiveconfigurationprofile
&Vn Viewstoredprofile(n=03)
&V8 Viewdifferencesbetweenactiveanddefault
&Wn Savecurrentconfigurationintostoredprofilen(n=0,1,2,3)
&Yn SelectstoredprofilenforPoweronand&D3
&Zn=x Storexasphonenumbern(x=09)
#A0 PreventRemoteAccess
#A1 Allowremoteaccess
#A2 n Allowremoteaccesswithsecuritypassword
#ALMn=x Dialnumber/sx(x=09in&Z)forremotealertn
#B0 n In1200bpsoriginatemodeB0=V.23,B2=V.22
#B1 In1200bpsoriginatemodeB0=V.22,B2=V.23
#C0 V.25callingtonesdisabled
#C1 n V.25callingtonesenabled
#J0 AssumeV.42compatibility
#J1 n CheckV.42compatibility
#K0 DisableMNP10
#K1 n EnableMNP10
#K2 EnableMNP10forCellularlinks
#MEM0 Allvoicefeaturesoff
#MEM1 n VoicemodeafterS110ringsifDTRislow
#MEM2 VoicemodeafterS110ringsregardlessofDTR
#MINI EraseVoicemodealarmmessage
#M0 n ATcommandoperation
#O0 n Charactersignoredifmodembuffersoverflow
IndustrialModemUserGuide
YML3913A 17
#O1 Disconnectsifterminalbufferoverflows
#O2 Disconnectsiflinebufferoverflows
#O3 Disconnectsifeitherbufferoverflows
#PIN=n PinNumberwherenisthepinnumber
#R0 RemoteControlMode
#V0 CommandandSRegisterverifieroff
#V1 n CommandandSRegisterverifieron
%B0 n S0=0settingafterAT&F
%B1 S0=2settingafterAT&F
%C0 Compressiondisabled
%C1 MNP5compressionenabled
%C2 V.42bisdatacompressionenabled
%C3 n V.42bisdatacompressionenabledwithfallbacktoMNP5
%Dn Setdisconnectdelaytonseconds(default%D0)
%E0 Disableautoretrain
%E1 n Enableautoretrain
%E2 AutomaticSpeedStepping
%H0 n UseBsettingforinitialMNP10connectionspeed
%H1 Initialconnectionismadeat1200bps(MNP10)
%H2 Initialconnectionismadeat4800bps(MNP10)
%H3 Initialconnectionismadeat9600bps(MNP10)
%H9 UseBsettingforconnectionbutdonotupshift(MNP10)
%K0 n CTSoperatesnormally
%K1 CTSoffduringdialandhandshake
%L0 Reportcurrentreceivedsignallevel(dBm)
%Ln Settransmitlevel(n=11to19;11dBmto 19dBm)
%M0 n ModeLEDsindicateconnectionspeed
%M1 ModeLEDsindicatelinequality,V.42/MNPerrors&flowctrl
%N0 n StandardBaudRates
%N1 Standardto14400then20800,31200,41600and62400
%N2 Standardto38400then51200
%P0 n CONNECTmessageappearsbefore DCDasserted
%P1 CONNECTmessageappearsafterDCDasserted
%Q Reportcurrentlinequality(EQM)(0=perfect)
%R0 n &RcommanddeterminesstateofCTS
%R1 CTSalwaysfollowsRTS(notresetby&F)
%R2 CTSfollowsDTRwhenoffline(notresetby&F)
%S0 n DSRisnotoverridden
%S1 DSRmimicsthestateofDTR(notresetby&F)
%T0 n DCDalwaysfollowsstateofcarrier
%T1 DCDisalwayshigh(notresetby&F)
%U0 n Standarderrorcorrectionresponsecodes
%U1 V.42responsecodeswhenV.42connectionestablished
%U2 V.42responsecodesforV.42connections,MNP2,4,10compression
%W0 n Disablewelcomemessage
%W1 Sendmessagespecifiedby*Wtoremotemodemafterconnect
\A0 MNPblocksize=64
\A1 MNPblocksize=128
\A2 MNPblocksize=192
\A3 n MNPblocksize=256
\Bn SendBreaksequencetoremotemodem(default \B3)
IndustrialModemUserGuide
YML3913A 18
\J0 n Fallbacktodirectmodedisabled
\J1 Fallbacktodirectmodeenabled
\Kn ReceivedBreakcontrol(default\K5)
\N0 Constantspeedmode
\N1 Variablespeedmode
\N2 MNPreliablemode
\N3 n V.42/MNPautoreliablemode
\N4 V.42reliablemode
\N5 V.42autoreliablemode
\N6 V.42/MNPreliablemode,fallbacktoMNPreliablemode
\N7 MNPautoreliablemode
\Q0 Flowcontroldisabled
\Q1 XON/XOFFflowcontrolfrommodemandcomputer
\Q2 CTSflowcontrol
\Q3 CTSRTSflowcontrol(sameas&K3)
\Q4 ModemonlyXON/XOFFflowcontrol
\Q5 CTSflowcontrol(CTSlowuntilconnection)
\Q6 CTSRTSflowcontrol CTSlowuntilconnect
\S Displayactiveconfigurationwithdetaileddescription
\Tn Setinactivitytimertonseconds(Default \T0)
\V0 n Disablereliableresponsecodes
\V1 Enablereliableresponsecodes
\V8 Extendedresponsecodes
\V9 Extendedresponsecodeswithdiagnosticinformation
\X0 n XON/XOFFpassthroughdisabled
\X1 XON/XOFFpassthroughenabled
*C0 n EnableV.34
*C1 DisableV.34useV.FC
*Wttt...tt Specifywelcomemessagetextusedby%W1(ttt...tt=textuse|fornewline)
Modulati onSetting
+MS? Reportselectedoptions
+MS=? Reportlistofsupportedoptions
+MS= <mod>,<automode>,<min_rate>,<max_rate><E>
<mod> seetable
<automode> =0(automodedisabled,fixedmodulation)
<automode> =1(automodeenabled,autoselectspeed/mod)
<min_rate> =lowestrateformodemconnection
<max_rate> =highestrateformodemconnection
<mod> Modulation PossibleRates(bps)
0 V.21 300
1 V.22 1200
2 V.22bis 2400or1200
3 V.23 1200
9 V.32 9600or4800
10 V.32bis 14400,12000,9600,7200,or4800
11n V.34 33,600,31,200,28800,26400,24000,21600,19200, 16800,14400,12000,
9600,7200,4800,or2400
64 Bell103 300
69 Bell212 1200
IndustrialModemUserGuide
YML3913A 19
DistinctiveRing
TheIndustrialModemisabletodiscriminatebetweenthreedifferenttypesofrings.Thisisusefulifyoupurchase
theTelstraDuetservice.WithTelstraDuet,twophonenumbersaresharedforonetelephoneline.Onenumber
canbeusedforVoiceandtheothernumbercanbeusedforyourModem.Toenablethemodemtoansweronly
whenyourmodemnumberisdialled,issuethe command:ATSDR=4S0=2&W.
ATSDR=n,x wheren=0to7,default=0,
x=0DisableDistinctiveRingresponsesuffix;
x=1EnableDistinctiveRingresponsesuffix(default)
ATSDR=0 Anyringdetectedandreportedas"RING"
ATSDR=1,1 Singleringdetectedand reportedas"RING1"
ATSDR=1,0 Singleringdetectedandreportedas"RING"
ATSDR=2,1 Doubleringdetectedandreportedas"RING2"
ATSDR=2,0 Doubleringdetectedandreportedas"RING"
ATSDR=3,1 Singleanddoubleringdetectedandreportedas"RING1"or"RING2"
ATSDR=3,0 Singleanddoubleringdetectedandreportedas"RING"
ATSDR=4,1 Tripleringdetectedandreportedas"RING3"
ATSDR=4,0 Tripleringdetectedandreportedas"RING"
ATSDR=5,1 Singleandtripleringdetectedandreportedas"RING1"or"RING3"
ATSDR=5,0 Singleandtripleringdetectedandreportedas"RING"
ATSDR=6,1 Doubleandtripleringdetectedandreportedas"RING2"or"RING3"
ATSDR=6,0 Doubleandtripleringdetectedandreportedas"RING"
ATSDR=7 Anyringdetectedandreportedas"RING1"or"RING2"or"RING3"
+ UseATSDR=4forTelstra'sDuetservice.DonotsetAutoAnswerbelow2whenDistinctiveRingis
enabled.
IndustrialModemUserGuide
YML3913A 20
Response Codes
Num Verbal Description
0 OK Commandaccepted
1 CONNECT Connectionestablished
2 RING Incomingcalldetected
3 NOCARRIER Carriernotdetected
4 ERROR Commanderror
6 NODIALTONE Dialtonehasnotbeendetected
7 BUSY Thenumberdialledisbusy
8 NOANSWER Silencenotdetected
13 RINGING Thenumberdialledisringing
5 CONNECT1200 Connectedat1200bps
10 CONNECT2400 Connectedat2400bps
11 CONNECT4800 Connectedat4800bps
32 CONNECT7200 Connectedat7200bps
12 CONNECT9600 Connectedat9600bps
30 CONNECT12000 Connectedat12000bps
31 CONNECT14400 Connectedat14400bps
33 CONNECT16800 Connectedat16800bps
34 CONNECT19200 Connectedat19200bps
35 CONNECT21600 Connectedat21600bps
36 CONNECT24000 Connectedat24000bps
37 CONNECT26400 Connectedat26400bps
38 CONNECT28800 Connectedat28800bps
95 CONNECT31200 Connectedat31200bps
97 CONNECT33600 Connectedat33600bps
AfulllistofresponsecodesisprovidedinyourSmartModemReferenceGuideincludedontheNetCommCD
ROM.
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Netcomm IG6000 User manual

Netcomm
Brand
Netcomm
Model
IG6000
Category
Networking
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents