White Rodgers 1F95-0477 User manual

Brand: White Rodgers

Model: 1F95-0477

Category: Microphones

Type: User manual

White Rodgers 1F95-0477 is a versatile, programmable thermostat designed to control heating and cooling systems efficiently. Compatible with various system types, including heat pumps, single-stage, and multi-stage systems, it offers flexibility for different home setups. The thermostat features automatic heat/cool changeover, ensuring optimal comfort without manual adjustments. It also includes customizable programming options, allowing you to create personalized schedules that align with your lifestyle and preferences.

Blue 4” Universal Thermostat with

Automatic Heat/Cool Changeover Option

Single Stage, Multi-Stage or Heat Pump

Installation and Operating Instructions for Model:

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS

CAREFULLY BEFORE INSTALLING OR OPERATING

THIS CONTROL COULD CAUSE PERSONAL INJURY

AND/OR PROPERTY DAMAGE.

Save these instructions for future use!

APPLICATIONS

SPECIFICATIONS

Electrical Rating:

Battery Power .................................................... mV to 30 VAC, NEC Class II, 50/60 Hz or DC

Input-Hardwire ................................................... 20 to 30 VAC

Terminal Load ........................................................... 1.5 A per terminal, 2.5A maximum all terminals combined

Setpoint Range ......................................................... 45° to 90°F (7° to 32°C)

Rated Differentials: Fast Med. Slow

Heat (SS1, MS2) ............................................... 0.4 °F 0.6 °F 1.7 °F

Cool (SS1, MS2) ................................................ 0.9 °F 1.2 °F 1.7 °F

Heat Pump (HP1, HP2) ..................................... 0.9 °F 1.2 °F 1.7 °F

Emer (HP1, HP2) ............................................... 0.6 °F – 1.7 °F

Operating Ambient .................................................... 32° to +105°F (0° to +41°C)

Operating Humidity ................................................... 90% non-condensing max.

Shipping Temperature Range ................................... -40° to +150°F (-40° to +65°C)

Dimensions Thermostat ............................................ 3-7/8”H x 5-1/8”W x 1-1/4”D

1F85-0477 Thermostat

Model Programming Choices

1F85-0477

7 Day 5/1/1 Day

ATTENTION: MERCURY NOTICE

This product does not contain mercury. However, this product

may replace a product that contains mercury.

Mercury and products containing mercury must not be

discarded in household trash. Do not touch any spilled

mercury. Wearing non-absorbent gloves, clean up any spilled

mercury and place in a sealed container. For proper disposal

of a product containing mercury or a sealed container. Refer

to www.white-rodgers.com for location to send product

containing mercury.

THERMOSTAT APPLICATION GUIDE

Description

Heat Pump (No Aux. or Emergency Heat) Ye s

Heat Pump (with Aux. or Emergency Heat) Ye s

Systems with up to 2 Stages Heat, 2 Stages Cool Ye s

Heat Only Systems (with optional fan switch) Ye s

Millivolt Heat Only Systems – Floor or Wall Furnaces Ye s

Cool Only Systems Ye s

Gas or Oil Heat Ye s

Electric Furnace Ye s

Hydronic (Hot Water) Zone Heat – 2 Wires Ye s

Hydronic (Hot Water) Zone Heat – 3 Wires Ye s

Index Page

Installation 2

Wiring Connections 2

Wiring Diagrams 3

Thermostat Quick Reference 5

Installer Conﬁguration Menu 6

Operating Your Thermostat 8

Programming 9

Troubleshooting 10

PART NO. 37-7238A

1118

CAUTION

To prevent electrical shock and/or equipment damage,

disconnect electric power to system at main fuse or

circuit breaker box until installation is complete.

www.white-rodgers.com

www.emersonclimate.com

INSTALLATION

Thermostat installation and all components of the

control system shall conform to Class II circuits per

the NEC code.

WARNING

Remove Old Thermostat

A standard heat/cool thermostat consists of three basic parts:

1. The cover, which may be either a snap-on or hinge type.

2. The base, which is removed by loosening all captive

screws.

3. The switching subbase, which is removed by unscrewing

the mounting screws that hold it on the wall or adapter

plate. Before removing wires from old thermostat,

label each wire with the terminal designation from

which it was attached. Disconnect the wires from the

old thermostat one at a time. Do not let wires fall back

into the wall.

Installing New Thermostat

1. Pull the thermostat body off the thermostat base. Forcing

or prying on the thermostat will cause damage to the unit.

2. Place base over hole in wall and mark mounting hole

locations on wall using base as a template.

3. Move base out of the way. Drill mounting holes. If you

are using existing mounting holes and the holes drilled

are too large and do not allow you to tighten base snug-

ly, use plastic screw anchors to secure the base.

4. Fasten base snugly to wall using mounting holes shown

in Figure 2 and two mounting screws. Leveling is for

appearance only and will not affect thermostat operation.

5. Connect wires to terminal block on base.

6. Push excess wire into wall and plug hole with a ﬁre re-

sistant material (such as ﬁberglass insulation) to prevent

drafts from affecting thermostat operation.

7. Carefully line the thermostat up with the base and snap

into place.

Batteries

2 “AA” alkaline batteries are included with the thermostat.

To install the batteries, pull the battery door as shown by the

arrow and lift open. Using the polarity indicated inside the bat-

tery door, insert the batteries. To close the battery door, swing

the door down while pulling in the direction of arrow. Once

fully down, snap the door back into position. To replace the

batteries, set system to OFF.

Thermostat can be powered by system AC power or Battery.

is displayed, the thermostat is battery powered. If

is not displayed, thermostat is system powered with optional

battery back-up. When battery power remaining is approxi-

mately half, the

will be displayed. When “Change ”

is displayed, install fresh “AA” alkaline batteries immediately.

For best results, replace all batteries with new premium brand

alkaline batteries such as Duracell

or Energizer

. We recom-

mend replacing batteries every 2 years. If the home is going

to be unoccupied for an extended period (over 3 months) and

is displayed, the batteries should be replaced before

leaving. When less than two months of battery life remain, the

setpoint temperature will offset by 10 degrees (10 degrees

cooler in Heat mode / 10 degrees warmer in Cool mode). If

offset occurs, the normal setpoint can be manually reset with

or . Another offset will occur within two days if batter-

ies are not replaced.

“AA” Alkaline Batteries

Figure 1 – Battery door shown open

Mounting

Hole

Mounting

Hole

Place Level

across

Mounting Tabs

(for appearance only)

Place Level

across

Mounting Tabs

(for appearance only)

Figure 2 – Thermostat base and rear view of thermostat

WIRING CONNECTIONS

Refer to equipment manufacturers’ instructions for speciﬁc system wiring information. After wiring, see CONFIGURATION section

for proper thermostat conﬁguration. Refer to ﬁgure 3 through 6 for wiring diagram speciﬁcations.

Terminal

Designation Description

L .............. Heat pump malfunction indicator for systems

with malfunction connection

O .............. Changeover valve for heat pump energized

constantly in cooling

B .............. Changeover valve for heat pump energized

constantly in heating

Y .............. Compressor Relay

Y2 ............. 2nd Stage Compressor

Terminal

Designation Description

W/E ............Heat Relay/Emergency Heat Relay (Stage 1)

W2 ............. 2nd Stage Heat (3rd Stage Heat in HP 2)

G ..............Fan Relay

RH .............Power for Heating

RC .............Power for Cooling

C ..............Common wire from secondary side of cooling system

transformer or heat only system transformer

6...............3 Wire Zone Valve – Energized when no call for Heat

TERMINAL DESIGNATION DESCRIPTIONS

Single

Stage 1

(SS1)

Multi-

Stage 2

(MS2)

Energized Constantly

in Cool Mode

Energized Constantly

in Heat, Off,

Emergency

Mode

Output

Cool

Mode

2nd

Stage

Cool Mode

1st Stage

Blower/

Circulator

Fan Energized

on Call for

Cool (and

Heat if

configured

for Electric

Heat)

No Output

Heat Mode

2nd Stage

Heat

Mode

1st Stage

Optional*

24 Volt

(Com-

mon)

24 Volt

(Hot)

Cool

System

W/E

CLASS II

TRANSFORMER

HOT

24VAC

NEUTRAL

120VAC

24 Volt

(Hot)

Heat

Jumper

Fault

Indicator

System

Malfunction

Switch

System Malfunction

Module

O/B

WIRING DIAGRAMS

Heat Pump Connections

If you do not have a heat pump system, refer to ﬁgures 4-6.

Refer to equipment manufacturers’ instructions for speciﬁc

system wiring information.

You can conﬁgure the thermostat for use with the following

heat pump systems.

Figure 3 – Heat Pump Systems

HEAT PUMP TYPE 1 (HP 1). Single stage compressor

system; gas or electric backup.

HEAT PUMP TYPE 2 (HP 2). Multi-stage compressor or two

compressor system with gas or electric backup.

After wiring, see INSTALLER CONFIGURATION section for

proper thermostat conﬁguration.

NOTE: If your system does

not provide an E connection,

jumper W2 to W/E to use

the Auxiliary Heat in the

Emergency Mode.

* Common connection

required for fault or

malfunction indication.

Heat Pump 2

(HP2)

Heat Pump 1

(HP1)

Energized in

Cool Mode

Energized in

Heat, Off,

Emergency

Mode

2nd

Stage

(Com-

pressor)

Output

Heat and

Cool Mode

1st Stage

(Compressor)

Blower/

Circulator

Fan Energized

on Call for

Heat or Cool.

Set Elect/Gas

Option for

Emergency

Mode

Heat Mode

2nd Stage.

Emergency

Mode 2nd

Stage

Heat Mode

3rd Stage.

Emergency

Mode 2nd

Stage

Emergency

Mode

1st Stage

Optional*

24 Volt

(Com-

mon)

Fault Indicator

or System

Malfunction

Switch

24 Volt

(Hot)

Cool

System

W/E

CLASS II

TRANSFORMER

HOT

24VAC

NEUTRAL

120VAC

24 Volt

(Hot)

Heat

Jumper

Comfort Alert II Module

or Similar System

Malfunction Module

O/B

Single Stage and Multi-Stage Connections

Refer to equipment manufacturers’ instructions for speciﬁc

system wiring information.

This thermostat is designed to operate a single-transformer

or two-transformer system.

You can conﬁgure the thermostat for use with the following

fossil fuel systems:

SINGLE STAGE (SS 1) gas, oil or electric.

MULTI-STAGE (MS 2) gas, oil or electric.

After wiring, see INSTALLER CONFIGURATION section for

proper thermostat conﬁguration.

Figure 4 – Single Stage or Multi-Stage System (No Heat Pump) with Single Transformer

* Common connection

required for fault or

malfunction indication.

WIRING DIAGRAMS

Figure 5 – Single Stage or Multi-Stage System (No Heat Pump) with Two Transformers

Single

Stage 1

(SS1)

Multi-

Stage 2

(MS2)

Output

Cool

Mode

2nd

Stage

Cool Mode

1st Stage

Blower/

Circulator

Fan Energized

on Call for

Cool (and

Heat if

configured

for Electric

Heat)

No Output

Heat Mode

2nd Stage

Heat

Mode

1st Stage

Optional

24 Volt

(Com-

mon)

Fault

Indicator

(NOT

USED)

24 Volt

(Hot)

Cool

System

W/E

CLASS II

TRANSFORMER

HOT

24VAC

NEUTRAL

120VAC

24 Volt

(Hot)

Heat

120VAC

Remove Jumper Wire

between RH & RC

HOT

24VAC

NEUTRAL

CLASS II

TRANSFORMER

HEATING

COOLING

Jumper

O/B

Energized Constantly

in Cool Mode

Energized Constantly

in Heat, Off,

Emergency

Mode

Single Stage

3-wire

Zone Valve

application

Blower/Circulator

Fan Energized

Opens

Valve

(4)

Constant

24 Volt

(Com-

mon)

24 Volt

(Hot)

Cool

System

CLASS II

TRANSFORMER

HOT

24VAC

NEUTRAL

120VAC

24 Volt

(Hot)

Heat

(5)

Jumper

Closes

Valve

(6)

Figure 6 – 3-Wire (SPDT) Heat Only Zone Valve Wiring

4 14

Month

Change

Filter

Call For Service

Save

Temp Hold

Date

Set

Schedule

SYSTEM FAN

Year

Run Hold

Heat

Mo Tu We Th Fr Sa Su

System On +2

Heat Pump

Auto Sched

Cool Savings

Em Auto Auto

Cool OffTime

Set

SYSTEM

Heat

FAN

Auto

Room

Temperature

Setting

Temperature

System

Indicator

Fan

Indicator

Battery Level Indicator

Indicating the current power

level of the 2 “AA” batteries.

Full power remaining.

Half power remaining.

Change The batteries

should be replaced at this time

with 2 new premium brand

“AA” Alkaline batteries.

(See page 2 for more details)

Time of day

Run

THERMOSTAT QUICK REFERENCE

Figure 7 – Home Screen Display

Home Screen Description

Programming and Conﬁguration Items

“System On” indicates when heating or cooling stage

is energized, “+2” ﬂashing indicates when a second

stage is energized.

The word “Hold” is displayed when the thermostat is in

the Hold mode. “Temp Hold” is displayed when

the thermostat is in a Temporary Hold mode.

Displays “Change Filter” when the system has run for

the programmed ﬁlter time period as a reminder to

change or clean your ﬁlter.

Displays “Set” for setpoint when in Run Program mode.

Displays System Mode (Heat, Em, Auto, Cool, Off)

or “Time” in Menu Mode.

Displays Fan Mode (On, Auto) in Menu Mode.

Displays “Set Schedule”, “Schedule”, or “Menu”.

Displays “Save” when Cool Savings

is working.

Displays “Heat Pump” when system is conﬁgured

as Heat Pump thermostat.

Displays “Hold” in programmable mode. When not in

Hold mode, displays “Run” in program run mode.

Initially displays “Auto Sched”. If Auto Schedule had

been used or disabled, then it displays “Cool Savings”

when in the Cool Mode if Cool Savings has been ena-

bled in the menu.

“Call For Service” indicates a fault in the heating/

cooling system, it does not indicate a fault in the

thermostat.

Alternates Time of Day and “LOC” when keypad lockout

is enabled.

In Conﬁguration Menu, shows screen number. If blank,

thermostat is earlier model and requires instruction sheet

37-7050B.

Figure 8 – Programming & Conﬁguration Items

INSTALLER/CONFIGURATION MENU

To enter the Conﬁguration Menu, SYSTEM must be set to HEAT, COOL, Em or AUTO. Press the Menu button for at least 5

seconds. The display will show item #1 in the table below. Press Menu button to advance to the next menu item. Press

to change an item option.

INSTALLER/CONFIGURATION MENU

SCREEN

NUMBER

MS2/

SS1

HP1/

HP2

DISPLAYED

(FACTORY DEFAULT)

Press

or to

select from listed options

COMMENTS

 

(OFF) Lk L Selects Keypad Lockout.

(Not available on earlier models)

 

(000) Lk 001 to 999 Selects Keypad lockout combination number

 

(MS 2) SS1, HP1, HP2 Selects Multi-Stage (MS 2 No Heat Pump),

Heat Pump 1 (HP 1, 1 compressor),

or Single Stage (SS 1), Heat Pump 2 (HP 2, 2

compressor or 2 speed compressor)



(GAS) ELE Select Gas or Electric heat



(ELE) GAS

 

(0) CS 1, 2, 3, 4, 5, 6 Selects Cool Savings

Value 1 (low) to 6 (high), Value 0 Disables Feature

 

(On) E OFF Selects Energy Management Recovery (EMR)

On or OFF.



(ME)

CR Heat

SL, FA Adjustable Anticipation:

Selects heating cycle rate for MS or SS



(ME)

CR Cool

SL, FA Adjustable Anticipation: Selects the cycle

rate for cooling (only when MS2 or SS1

is selected in item 1)

 

(ME)

CR Heat Pump

SL, FA Adjustable Anticipation (Heat Pump)

(only when heat pump is selected in #1)

 

(FA)

CR Em

SL Selects the cycle rate for Emergency

mode and Auxiliary stage if Heat Pump is

selected in item 1)

 

(OFF) CL CL On Compressor Lockout Time

 

Heat-Auto

Cool-Off

Cool-Off, Heat-Off,

Heat-Fan-Off,

Heat-Cool Auto-Off

Select System Switch Conﬁguration with automatic

changeover capability

 

(On) dL dL OFF Selects Display Light On or OFF

 

(current temperature)

1 HI, 2 HI, 3 HI, 4 HI,

1 LO, 2 LO, 3 LO, 4 LO

Adjustable Ambient Temperature Display

 

°F °C

Selects Fahrenheit/Celsius Temperature Display

 

L (90) Heat L 62 to L 89 Selects Limited HEAT Range

 

L (45) Cool L 46 to L 82 Selects Limited COOL Range

 

P7 P3 Defaults for 7 day programming (P7) or 5/1/1 day

programming (P3) is available

 

(On) AS Heat OFF Automatic Schedule for heat mode.

 

(On) AS Cool OFF Automatic Schedule for cool mode.



MS (On) FA Heat OFF Fast Heat option may be disabled by

selecting OFF. NA to SS conﬁg.

22 HP2



(On) FA Cool OFF Fast Cool option may be disabled by

selecting OFF. NA to SS conﬁg.

NA to Heat only system.

 

(OFF) CA

Selects active Comfort Alert On or OFF.

Require CA II Module. (Not available on earlier models)

 

(On) dS OFF Selects Automatic daylight Savings Time

option On or OFF.

 

(OFF) Change Filter On Selects Filter Change-out Indicator On or OFF.

 

(200 h) Change Filter 25-1975 h Change Filter time in 25 hour increments. This

menu only appears if On is selected in above.

 

(o) On Cool (b) On Heat Selects operation of the reversing valve terminal (O/B)

output as an O or B terminal.

INSTALLER/CONFIGURATION MENU

1 & 2)Keypad Lockout – This menu selection will display

“Lk” and “OFF” (default, keypad not locked out). The

and are used to toggle the selection between

OFF and “L” (keypad locked out). When the keypad

lockout selection is enabled “L” , and the MENU button

is pressed again, the display will indicate the number

“0” (default, still disabled) in the time digits. The

and

are used to set the combination number from 0

to 999. If a combination of 0 is selected and the MENU

button is pressed, the menu will be exited and keypad

will not be locked. If 1 to 999 is selected and the MENU

button is pressed, the combination is stored into memory

and the menu is exited. The “Lk” will display designating

keypad locked with a valid combination. The SYSTEM

button will operate for 10 seconds after the menu mode

is exited to allow the user to change the mode from

“OFF” to the desired SYSTEM mode.

While the keypad is locked out, a press of MENU will en-

ter the conﬁguration menu. The ﬁrst menu item displayed

is the combination code “0”. The

or keys are

used to set the combination unlock number from 0 to

999. If the unlock number matches exactly with the com-

bination lock number stored in memory when the MENU

button is pressed, the keypad is unlocked and the “Loc”

is removed. If the unlock number does not match when

the MENU button is pressed, the combination returns to

“0” for another attempt to set the unlock code. To exit the

menu without unlocking the keypad, press RUN SCHED.

To reset the combination code and unlock the keypad if

the code is forgotten, see troubleshooting section.

3) This control can be conﬁgured for:

MS 2 – Multi-Stage System (no heat pump)

HP 1 – Heat Pump with one stage of compressor

HP 2 – Heat Pump with two stage compressor or two

compressor system, Gas or Electric backup

SS 1 – Single Stage System

4) GAS or Electric (ELE) fan operation. If the heating sys-

tem requires the thermostat to energize the fan, select

ELE. Select GAS if the heating system energizes the fan

on a call for heat.

5) Select Cool Savings™ value – Selects the amount

of adjustment for the Cool Savings™ feature in Cool

mode with 1 (1°) being the least amount of adjustment

and 6 (6°) being the most amount of adjustment. Default

value is 0 which disables this feature. Selecting a value

greater than 0 will display Cool Savings on the screen

and enable the key for Cool Savings feature. Cool Sav-

ings is an optional energy saving feature that can reduce

your cooling costs. It is based on the principal that lower

indoor humidity makes a slightly higher temperature

feel more comfortable. Cool Savings operates during

periods of high demand which normally occur on the

hottest summer days when a cooling system may run

for hours to reach the thermostat setting. Long cooling

run times also lower the indoor humidity. Cool Savings,

very slowly, adjusts the setpoint temperature to make the

setpoint closer to the displayed room temperature, to a

maximum of the number of degrees you select. Adjust-

ing the setpoint temperature over a long cooling run time

allows the system to reach your set temperature and turn

off. The room temperature will actually be higher than

the thermostat displays but the reduction in humidity will

allow comfort at the slightly higher temperature.

To turn this feature on in the Cool mode press Cool

Savings. The display will show “Save” next to the

setpoint temperature. When Cool Savings is making ad-

justments to the room temperature display “Save” will be

ﬂashing and the displayed room temperature may vary

within the adjustment range you selected.

If “Save” is not displayed and this feature is OFF, no

change will occur when the cooling system is continu-

ously running during periods of high demand.

6) Energy Management Recovery: Energy Management

Recovery (E) On enables the thermostat to start heating

or cooling early to make the building temperature reach

the program setpoint at the time you specify. Heating

will start approximately 5 minutes early for every 1° of

temperature required to reach setpoint.

Example: E On is selected and your heating is pro-

grammed to 65° at night and 70° at 7 AM. If the build-

ing temperature is 65°, the difference between 65° and

70° is 5°. Allowing 5 minutes per degree, the thermostat

setpoint will change to 70° at 6:35 AM. Cooling allows

more time per degree, because it takes longer to reach

set temperature.

7, 8,9 & 10) Cycle Rate Selection – The factory default

setting for Heat and Cool modes, SS1, MS2, is medium

cycle (ME). For Heat Pump, HP1, HP2, the default set-

ting is medium (ME). For Emer (Aux) the default setting

is fast cycle (FA). To change cycle rate, press the

key.

Cycle rate differentials for different settings are:

Fast Medium Slow

MODE FA ME SL

Heat (SS1, MS2) 0.4°F 0.6°F 1.7°F

Cool (SS1, MS2) 0.9°F 1.2°F 1.7°F

Heat Pump (HP1, HP2) 0.9°F 1.2°F 1.7°F

Emer (HP1, HP2) 0.6°F - 1.7°F

11) Select Compressor Lockout CL OFF or ON – Select-

ing CL ON will cause the thermostat to wait 5 minutes

between cooling cycles. This is intended to help protect

the compressor from short cycling. Some newer com-

pressors already have a time delay built in and do not

require this feature. Your compressor manufacturer can

tell you if the lockout feature is already present in their

system. When the thermostat compressor time delay oc-

curs, it will ﬂash the setpoint for up to ﬁve minutes.

12) System Mode Conﬁguration – This thermostat is

conﬁgured for Heat and Cool (SYSTEM switch with Cool,

Off, Heat) default. It can also be conﬁgured for Heat and

Cool with Auto changeover (Heat, Auto, Cool, Off), Heat

only with fan (Off, Heat), Heat only without fan, Auto only

(Auto, Off), and Cool only (Cool, Off).

13) Select Backlight Display – The display backlight im-

proves display contrast in low lighting conditions. When

the “C” terminal is powered, selecting backlight CdL ON

will keep the light on continuously. Select backlight OFF

will turn the light on momentarily after any key is pressed.

When the “C” terminal is not powered, the light will be on

momentarily after any key is pressed no matter whether

the backlight is selected ON or OFF.

14) Select Temperature Display Adjustment 4 LO to 4 HI

– Allows you to adjust the room temperature display up

to 4° higher or lower. Your thermostat was accurately cali-

brated at the factory, but you have the option to change

the display temperature to match your previous thermo-

stat. The current or adjusted room temperature will be

displayed.

15) Select F° or C° Readout – Changes the display readout

to Celsius or Fahrenheit as required.

16 & 17) Temperature Limit Range Heat or Cool – This

selection sets the maximum HEAT (13) or minimum

COOL (14) temperature for the setpoint range. Select the

limit temperature using the

or keys. In the Run

mode, the setpoint temperature will not adjust past the

limit temperature selected. When the limit temperature is

reached, trying to raise or lower the setpoint past the limit

will cause “L” to be displayed in the times digits for about 6

seconds. This feature not available on earlier models.

18) Program Options: Conﬁgured for 7 day or 5/1/1 day pro-

gramming or non-programmable mode. The default set-

ting is P7, indicating 7 day programming. The programs

INSTALLER/CONFIGURATION MENU

per week can be changed to P3 by pressing the or

keys. A selection of 0 Days for non-programmable

will eliminate the need for EMR, and that step in the

menu will be skipped.

19 & 20) Select Automatic Schedule – With just one touch

of the AUTO SCHEDULE button this feature allows

you to program a desired comfort temperature into all

the program periods along with a 6° set back for night

periods of both Heat and Cool programs. Factory default

is “On” for both. When Heat AS On and Cool AS On

are activated while in Heat or Cool mode, select desired

setpoint temperature and press AUTO SCHEDULE. This

value will be copied into all the morning, day and evening

program periods. The night program periods will have a

6°F set back.

21 & 22) Select Fast Second Stage ON or OFF – Heat

pump or Multi-stage only, in the run mode, with the fast

Heat feature enabled (FA Heat On), if the Heat setpoint

temperature is manually raised by 3°F (2°C) or more

above the actual temperature using

the second

stage will energize immediately. With FA OFF, second

stage will not energize until the setpoint temperature is

1°F or more above actual temperature for more than ten

minutes. The Fast Cool feature (FA Cool) provides the

same controls when the setpoint temperature is lowered.

23) Comfort Alert with Active Protection – Turn this

feature ON to enable active protection. This allows the

thermostat to identify fault codes sent by the Comfort

Alert module when compressor damage is possible and

react to those codes by turning the compressor off. Fault

codes from the Comfort Alert module will ﬂash on the

thermostat. (Refer to Comfort Alert Yellow Alert Codes

in Troubleshooting section.) If a Comfort Alert module is

not connected, or to disable active protection, turn this

feature OFF. If a Comfort Alert module is connected and

this feature is turned OFF, the thermostat will still receive

and ﬂash the fault codes from the Comfort Alert module,

but the active protection will not be enabled to protect the

compressor.

24) Select Daylight Saving Time Calculation – This feature

will allow the thermostat to calculate the DST automati-

cally and apply it to the Real Time Clock display. Default

On. Use

or buttons to select the feature OFF.

25 & 26) Select Filter Replacement Reminder and Set

Run Time – Select the “Change Filter” reminder On

or OFF. If selected On, press MENU to select the time

period from 25 to 1975 hours in 25 hours increments.

In a typical system, 200 hours (default) of run time is

approximately 30 days. After the selected time of blower

operation, the thermostat will display “Change Filter”

as a reminder to change or clean your air ﬁlter. When

“Change Filter” is displayed, press MENU or RUN but-

ton to clear the display and restart the time to the next

ﬁlter change.

27) Select Reversing Valve Output – The O/B option is

factory set at “O” position. This will accommodate the

majority of heat pump applications, which require the

changeover relay to be energized in COOL. If the

thermostat you are replacing or the heat pump being

installed with this thermostat requires a “B” terminal, to

energize the changeover relay in HEAT, the O/B option

should be set at “B” position.

OPERATING YOUR THERMOSTAT

Choose the Fan Setting (Auto or On)

Press the FAN button to Auto or On.

Fan Auto is the most commonly selected setting and runs the

fan only when the heating or cooling system is on.

Fan On runs the fan continuously for increased air circulation

or to allow additional air cleaning.

Choose the System Setting

(Heat, Off, Cool, Auto, Emer)

Press the SYSTEM button to select:

Heat: Thermostat controls only the heating system.

Off: Heating and Cooling systems are off.

Cool: Thermostat controls only the cooling system.

Auto: Auto Changeover is used in areas where both heating

and cooling may be required on the same day. AUTO allows

the thermostat to automatically select heating or cooling

depending on the indoor temperature and the selected heat

and cool temperatures. When using AUTO, be sure to set the

Cooling temperatures more than 1° Fahrenheit higher than

the heating temperature.

Em: (Heat Pump models) Thermostat controls only backup

heating system.

Manual Operation (Bypassing the Program)

Programmable Thermostats

Press or and then the HOLD button and adjust the

temperature wherever you like. This will override the program.

The HOLD feature bypasses the program and allows you

to adjust the temperature manually, as needed. Whatever

temperature you set in HOLD will be maintained 24 hours a

day, until you manually change the temperature or press RUN

to cancel HOLD and resume the programmed schedule.

IMPORTANT!

Program Override (Temporary Override)

Press or buttons to adjust the temperature. This

will override the temperature setting for two hours minimum

or until the next programmed time. To cancel the temporary

setting at any time and return to the program, press RUN. If

the SYSTEM button is pressed to select AUTO the thermostat

will change to Heat or Cool, whichever ran last. If it switches

to heat but you want cool, or it changes to cool but you want

heat, press both

and buttons simultaneously to

change to the other mode.

Second Stage Time Delay

Your thermostat is designed to determine the optimum time

to activate the second stage. Simply raising the temperature

in heating or lowering it in cooling will not always force the

thermostat to bring the second stage on quickly. There is a

time delay from 0-30 minutes depending on the performance

of the ﬁrst stage of the system.

EXAMPLE: For the last 2 hours the thermostat is set on 70°

and the room temperature is 70° with the equipment using

only the ﬁrst stage of heat. Since the equipment is keeping

the temperature within 1° of setpoint, the thermostat will

delay second stage for a longer time if you manually raise

the temperature or if the room temperature quickly changes.

Once the second stage comes on, it will come on sooner the

next time there is a difference between the setpoint and the

room temperature. The net effect of the staging program is

that when the ﬁrst stage is capable of making temperature

the second stage will delay longer. When the thermostat

calculates that ﬁrst stage cannot make temperature in a

reasonable time, the second stage will come on sooner. This

built in function automatically optimizes the use of additional

stages of heat or cool.

Set Current Time and Date

1) Press Menu and then Time button once. The display

will show the hour only.

2) Press and hold either the

or button until you

reach the correct hour and AM/PM designation (AM

begins at midnight, PM begins at noon).

3) Press TIME once again. The display window will show

the minutes only.

4) Press and hold either the

or button until you

reach the correct minutes.

5) Additional presses of TIME will advance the display to

show the year, month and date of month. Press the

or button to change the display to the correct set-

ting for each.

6) Press RUN to exit the TIME mode.

PROGRAMMING

The programmable thermostats are programmed with the energy saving settings shown in the table below for all days of the

week. If this program suits your needs, simply set the thermostat clock and press the RUN button. The table below shows the

factory set heating and cooling schedule for all days of the week.

Wake Up

(Period 1)

Leave For Work

(Period 2)

Return Home

(Period 3)

Go To Bed

(Period 4)

Heating

Program

6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F

Cooling

Program

6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F

Planning Your Program – Important

The Heating and Cooling Program schedules below allow you

to pencil in your own program times and temperatures.

The thermostat comes conﬁgured for 7 day programming

and can also be conﬁgured for 5/1/1 day programming (see

conﬁguration section).

Factory settings are listed on Monday through Friday, Satur-

day and Sunday. If you are re-programming a 7 day schedule,

pencil in all lines with the times and temperatures you want.

If you are re-programming a 5+1+1 ﬁll in your own times and

temperatures directly below the factory times and tempera-

tures.

Keep the following guidelines in mind when planning your

program.

• InHeating,lowertemperatureswillsaveenergy.

• InCooling,highertemperatureswillsaveenergy.

• IfyouplanonusingAutoChangeover,donotprogram

the heating higher than the cooling.

Energy Saving ENERGY STAR

Factory Pre-Program

Enter the Heating Program

1) Press SYSTEM button to select “Heat” in the system

switch area indicating the active mode being pro-

grammed.

2) Press the MENU button and then press SCHEDULE.

3) The top of the display will show the day(s) being pro-

grammed. The time and temperature (ﬂashing) are also

displayed. “1” will also be displayed to indicate the period.

4) Press

or button to change the temperature to

your selected temperature for the 1st heating period.

5) Press TIME button, time will ﬂash.

6) Press

or button to adjust the start time for the

1st period.

7) The time will change in 15 minute increments.

8) After you have set the time and the temperature for

the period to begin, press SCHEDULE to advance to the

next program period.

9) Repeat steps 2 through 8 until all of the program times

and temperatures are set for all program periods on

that day.

10) Press SCHEDULE to the next day and repeat steps 2

through 9.

11) When programming is complete and all of the times and

temperatures match your desired heating schedule, press

RUN. The thermostat will now run your program.

Enter the Cooling Program

1) Press SYSTEM button to select “Cool” in the system

switch area indicating the active mode being pro-

grammed.

2) Follow Enter Heating Program instructions for entering

cooling times and temperatures.

Worksheet for Re-Programming 7 Day and 5+1+1 Day Program

Cooling

Program

Wake Up

(Period 1)

Leave For Work

(Period 2)

Return Home

(Period 3)

Go To Bed

(Period 4)

MON

6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F

TUE

WED

THU

FRI

SAT

6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F

SUN

6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F

Heating

Program

Wake Up

(Period 1)

Leave For Work

(Period 2)

Return Home

(Period 3)

Go To Bed

(Period 4)

MON

6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F

TUE

WED

THU

FRI

SAT

6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F

SUN

6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F

PROGRAMMING

TROUBLESHOOTING

Comfort Alert Codes

The Comfort Alert diagnostics product monitors the air

conditioning outdoor systems with single phase Copeland

Scroll compressors. Abnormal system and electrical

conditions are indicated by ﬂashing ALERT codes on the

yellow LED on the Comfort Alert module. The ﬂash codes are

transmitted to the thermostat by the Comfort Alert Thermostat

interface module. The Comfort Alert compatible thermostat

displays “Call For Service” that ﬂashes at the same rate as

the yellow LED on the Comfort Alert module.

Comfort Alert Yellow Alert Codes

1 Flash Long run time

2 Flashs System pressure trip

3 Flashs Short cycling

4 Flashs Locked rotor

5 Flashs Open circuit

6 Flashs Open start circuit

7 Flashs Open run circuit

8 Flashs Welded Contactor

9 Flashs Low voltage

Symptom Possible Cause Correction Action

No Heat/No Cool/No Fan

(common problems)

1. Blown fuse or tripped circuit breaker.

2. Furnace power switch to OFF.

3. Furnace blower compartment door or

panel loose or not properly installed.

4. Loose connection to thermostat or

system.

Replace fuse or reset breaker.

Turn switch to ON.

Replace door panel in proper position to engage safety

interlock or door switch.

Tighten connections.

No Heat

1. Pilot light not lit.

2. Furnace Lock-Out Condition. Heat

may also be intermittent.

3. Heating system requires service or

thermostat requires replacement.

Re-light pilot.

Many furnaces have safety devices that shut down when

a lock-out condition occurs. If the heat works intermittently,

contact the furnace manufacturer or local HVAC service

person for assistance.

Diagnostic: Set SYSTEM Switch to HEAT and raise the

setpoint above room temperature. Within a few seconds

the thermostat should make a soft click sound. This sound

usually indicates the thermostat is operating properly. If

the thermostat does not click, try the reset operation listed

above. If the thermostat does not click after being reset

contact your heating and cooling service person or place

of purchase for a replacement. If the thermostat clicks,

contact the furnace manufacturer or a HVAC service

person to verify the heating is operating correctly.

No Cool

1. Cooling system requires service or

thermostat requires replacement.

Same as diagnostic for No Heat condition except set the

thermostat to COOL and lower the setpoint below the room

temperature. There may be up to a ﬁve minute delay before

the thermostat clicks in Cooling.

Heat, Cool or Fan

Runs Constantly

1. Possible short in wiring.

2. Possible short in thermostat.

3. Possible short in heat/cool/fan system.

4. FAN Switch set to Fan ON.

Check each wire connection to verify they are not shorted

or touching together. No bare wire should stick out from

under terminal block. Try resetting the thermostat as

described above. If the condition persists, the manufacturer

of your system or service person can instruct you on how

to test the Heat/Cool system for correct operation. If the

system operates correctly, replace the thermostat.

Thermostat Setting &

Thermostat Thermometer

Disagree

1. Thermostat thermometer setting

requires adjustment.

The thermometer can be adjusted +/- 4 degrees. See

Temperature Display Adjustment in the Conﬁguration Menu

section.

Furnace (Air Conditioner)

Cycles Too Fast or Too

Slow (narrow or wide

temperature swing)

1. The location of the thermostat and/or

the size of the Heating System may

be inﬂuencing the cycle rate.

Digital thermostats provide precise control and cycle faster

than older mechanical models. The system turns on and off

more frequently but runs for a shorter time so there is no

increase in energy use. If you would like an increased cycle

time, choose SL for slow cycle in the Conﬁguration menu,

step 6 (heat), 7 (cool) or 8 (heat pump). If an acceptable

cycle rate is not achieved, contact a local HVAC service

person for additional suggestions.

Forgot Keypad Lockout

Code

Hold MENU key for 20 seconds and the lockout will reset.

Thermostat does not have

Menu Screen Numbers

1. Earlier version of thermostat. Refer to Instruction Sheet 37-7050B.

TROUBLESHOOTING

Reset Operation

Note: When thermostat is reset, installer conﬁguration menu

settings and programming will reset to factory settings.

If a voltage spike or static discharge blanks out the display

or causes erratic thermostat operation, you can reset the

thermostat by removing the wires from terminals R and C

(do not short them together) and removing batteries for 2

minutes. After resetting the thermostat, replace the wires and

batteries. If the thermostat has been reset and still does not

function correctly contact your heating/cooling service person

or place of purchase.

Note: Be sure to review the installer conﬁguration menu

settings.

To reset the programming, clock and conﬁguration settings,

press

and and the FAN button simultaneously. The

thermostat should go blank and then all segments will be

displayed momentarily.

www.white-rodgers.com

www. emersonclimate.com

HOMEOWNER HELP LINE: 1-800-284-2925

White-Rodgers is a division

of Emerson Electric Co.

The Emerson logo is a

trademark and service mark

of Emerson Electric Co.

White Rodgers 1F95-0477 User manual

Brand: White Rodgers

Model: 1F95-0477

Category: Microphones

Type: User manual

Download PDF

report

White Rodgers 1F95-0477 User manual

White Rodgers 1F95-0477 User manual

Related papers

Other documents