1
Owner's Manual
Liquid Propane Gas Grill
MODEL SS64 LP
WARNING:
Read this Owner's Manual carefully and be sure
your gas grill is properly assembled, installed and
maintained. Follow all leak check procedures
carefully in this manual prior to grill operation. Do
this even if the grill was store assembled.
Failure to follow these instructions could result in
serious bodily injury and/or property damage.
This grill is intended for outdoor use only and is
not intended to be installed in or on recreational
vehicles or boats.
!
Note to Installer:
Leave this Owner's Manual
with the consumer after delivery and/or installation.
Customer Service:
If you have questions about assembly or grill operation, or if there are damaged
or missing parts when you unpack this unit from the shipping boxes, call us 8:00am - 5:00 pm EST,
Monday through Friday at:
1-800-667-7313
Note to Consumer:
Leave this Owner's Manual
in a convenient place for future reference.
Imported by S.R. Potten Ltd/Ltée
1645 – 50
th
AVENUE. LACHINE, QUEBEC,
CANADA H8T 3C8
MODEL SS64 LP SHOWN
Natural Gas Grill
MODEL SS64 NG
Important Note:
This grill is manufactured to
exact specifications. Model SS64 LP is certi-
fied for use with Liquid Propane Gas and Model
SS64 NG is certified for use with Natural Gas.
You can not convert this grill from one fuel
type to the other. For your safety, conversion
kits are not available. Any attempt to convert
your grill will void your warranty.
P80153005R-Date: 12/05/2006
2
Table of Contents
Read These Safety Instructions
Grill Installation Codes
Correct LP Gas Tank Use
LP gas grill models are designed for use with
a standard 20 lb. Liquid Propane Gas (LP gas)
tank, not included with grill box. Never connect
your gas grill to an LP gas tank that exceeds
this capacity. A tank of approximately 12 inches
in diameter by 18-1/2 inches high is the maxi-
mum size LP gas tank to use. You must use
an "OPD" gas tank which offers a listed
Overfill Prevention Device. This safety feature
prevents the tank from being overfilled which can
cause malfunction of the LP gas tank, regulator
and/or grill.
!
WARNING
Combustion by products produced when using
this product contain chemicals known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death, or property
damage.
!
WARNING
Your grill will get very hot. Never lean over the
cooking area while using your grill. Do not touch
cooking surfaces, grill housing, grill lid or any other
grill parts while the grill is in operation, or until
the grill has cooled after use.
Failure to comply with these instructions may
result in serious bodily injury.
!
WARNING
WARNING
(a) Do not store a spare LPG-gas cylinder
under or near this appliance.
(b) Never fill the cylinder beyond 80 percent full
and
(c) If the information in "(a)" and "(b)" is not
followed exactly, a fire causing death or
serious injury may occur.
!
1.
2.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
An LP gas tank not connected for use
shall not be stored in the vicinity of this or
any other appliance.
Grill Chef Warranty
Full 1-Year Warranty on Grill
For one year from date of original retail purchase, S.
R. Potten Ltd. (Manufacturer) will replace any grill part
that fails or is found to be defective in material or
workmanship in normal household use during the
warranty period.
Limited Warranty on Selected Grill Parts
From the date of original retail purchase, the manufac-
turer will replace, at its option, the following grill parts
if they are defective in material or workmanship in
normal household use. Delivery charges may apply.
• Lifetime Limited Warranty: Any stainless steel
part or aluminum casting which fails due to defective
materials or workmanship in normal household use
during the second through the useful lifetime of the
grill will be repaired or replaced. Discoloration or
denting of stainless steel parts or aluminum castings
which occurs due to normal use and/or exposure to
excessive heat, and/or improper maintenance is not
covered under the terms of this limited warranty.
•5 Year Limited Warranty: Stainless steel burners
which fail due to defective materials or workmanship
in normal household use during the second through
fifth year from the date of original retail purchase will
be repaired or replaced.
• For Warranty Service: Call our Customer Service
Dept. 8:00am - 5:00pm Eastern, Monday through
Friday at 1-800-667-7313
Warranty Restrictions:
This warranty does not cover surface rust or
natural oxidation.
This warranty is void if grill is used for commercial
or rental purposes.
This warranty applies only when the grill is used
in Canada.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
province to province. See back cover for warranty
details.
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your gas
supplier or your fire department.
If you smell gas:
FOR YOUR SAFETY
Warranty..................................................... 2
Safety Instructions ..................................... 2
Natural Gas Safety Instructions .............. 4
Pre-Assembly Instructions..............................5
Hardware, Parts Diagram and Lists ..... 6
Assembly Instructions............................... 11
The installation must conform with local codes or
in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z21.58a-2006/CSA
1.6a-2006 Natural Gas and Propane
Installation
Code.
LightingInstructions .................................. 19
Back Burner, Rotisserie Instructions..... 21
Cleaning and Maintenance Instructions .... 24
Frequently Asked Questions .................. 26
Cooking Instructions................................ 27
3
•
Never connect an unregulated LP gas tank to
your gas grill. The gas Regulator assembly
supplied with your gas grill is adjusted to have
an outlet pressure of 11" water column (W.C.)
for connection to an LP gas tank.
• Only use the Regulator and Hose Assembly
supplied with your gas grill. Replacement
Regulators and Hose Assemblies must be
those specified by manufacturer.
• Have your LP gas tank filled by a reputable propane
gas dealer and visually inspected and
re-qualified at each filling.
• Never fill the gas tank beyond 80% full.
Have your propane gas dealer check the release
valve after every filling to ensure that it remains
free of defects.
• Always keep LP gas tanks in upright position.
• Do not store (or use) gasoline or other flammable
vapors and liquids in the vicinity of this gas grill.
• An LP gas tank that is not connected for use must
NOT be stored on bottom shelf inside cabinet or in
the vicinity of this or any other gas grill.
• Do not subject the LP gas tank to excessive heat.
• Never store an LP gas tank indoors. If you
store your gas grill in the garage or other indoor
location, always disconnect the LP gas tank
first, store it safely outside.
• LP gas tanks must be stored outdoors in a
well-ventilated area and out of the reach of
children. Disconnected LP gas tanks must not
be stored in a building, garage or any other
enclosed area.
• When your gas grill is not in use the gas
must be turned off at the LP gas tank.
Proper Placement and Clearance of Grill
Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area. Your gas grill is to
be used outdoors only, at least 36 inches from the back
and side of any combustible surface. Your gas grill
should not be placed under any surface that will burn.
Do not obstruct the flow of ventilation air around the
gas grill housing.
This outdoor gas grill is not intended to be installed in
or on recreational vehicles and/or boats.
The LP gas tank has a Shut Off Valve, terminating
in an LP gas supply tank valve outlet, that is
compatible with a Type 1 tank connection device.
The LP gas tank must also have a safety relief
device that has a direct communication with the
vapor space of the tank.
The tank supply system must be arranged for
vapor withdrawal.
The LP gas tank used must have a collar
to protect the tank valve.
1.
2.
3.
• The Regulator and Hose assembly must be
inspected before each use of the grill. If there
is excessive abrasion or wear or if the hose
is cut, it must be replaced prior to the grill
being used again.
• Keep the gas Regulator Hose away from hot
grill surfaces and dripping grease. Avoid
unnecessary twisting of hose. Visually inspect
hose prior to each use for cuts, cracks,
excessive wear or other damage. If the Hose
appears damaged do not use the gas grill, call
our Customer Service Dept. for a replacement,
at 1-800-667-7313.
• Never light your gas grill with the Lid closed
or before checking to insure the Burner Tubes
are fully seated over the Gas Valve Orifices.
• Never allow children to operate your grill. Do
not allow children to play near your grill.
Failure to comply with these instructions
could result in a fire or explosion that could
cause serious bodily injury, death, or prop-
erty damage.
WARNING
A strong gas smell, or the hissing sound of gas
indicates a serious problem with your gas grill
or the LP gas tank. Failure to immediately follow
the steps listed below could result in a fire or
explosion that could cause serious bodily
injury, death, or property damage.
NOTE: The normal flow of gas through the
Regulator and Hose Assembly can create a
humming sound. A low volume of sound is
perfectly normal and will not interfere with opera-
tion of the grill. If humming sound is loud and
excessive you may need to purge air from the
gas line or reset the Regulator excess gas flow
device. This purging procedure should be done
every time a new LP gas tank is connected to
your grill. For help call the Grill Information
Center.
Customer Service Dept., 8:00am-5:00pm
EST, Monday through Friday at:
1-800-667-7313
• Shut off gas supply to the gas grill.
• Turn the Control Knobs to OFF position.
• Put out any flame with a Class B fire
extinguisher.
• Open Grill Lid.
• Get away from the LP gas tank.
• Do not try to fix the problem yourself.
• If odor continues or you have a fire you cannot
extinguish, call your fire department. Do not call
near the LP gas tank because your telephone is
an electrical device and could create a spark
resulting in fire and/or explosion.
WARNING
!
!
4
Natural Gas Safety Instructions
•
Your Natural Gas Grill is designed to operate on
Natural Gas only, at a pressure of 7" water column
(W.C.) (1/4 psig or 1.75 kpa), regulated at the
residential meter. Check with your gas utility com-
pany for local gas pressure and with your local
municipality for building code requirements. If your
residential gas line pressure has not been
regulated to 7" W.C., contact your local gas utility
company for professional assistance.
•
The gas pressure Regulator supplied with this
appliance must be used. This Regulator is set
for an outlet pressure of 4" W.C.
•
It is recommended that a Shut Off Valve be installed
at the gas supply source outdoors. Install at a point
after the gas pipe exits the outside wall and before the
Quick Disconnect Hose, or install it at the point
before the gas line piping enters the ground. See
Figure 1.
•
Pipe sealing compound or pipe thread tape resistant
to the action of Natural Gas must be used on all male
pipe threads when making the connection.
•
Disconnect your gas grill from fuel source when
the gas supply is being tested at high pressures.
This gas grill and its individual Shut Off Valve must
be disconnected from the gas supply pipe system
during any pressure testing of that system at
pressure in excess of 1/2 psi (3.5kpa).
•
Turn off your gas grill when the gas supply is
tested at low pressures. The grill must be
isolated from the gas supply pipe system
by closing its individual Manual Shut Off
Valve during any pressure testing of the gas
supply pipe system at pressures equal to
or less than 1/2 psi (3.5kpa).
•
The Quick Disconnect connects to a 3/8 inch
NPT thread from gas source. The Quick
Disconnect fitting is a hand operated device
that automatically shuts off the the flow of
gas from the source when it is disconnected.
•
The Quick Disconnect fitting can be installed
horizontally,or pointing downward.DO NOT
install the fitting with the opening pointing
upward because the fitting could collect water
and debris.
•
The Dust Covers (plastic plugs) provided with
the Quick Disconnect help keep the open
ends clean while disconnected.
•
The outdoor connector must be firmly attached to
a ridged permanent construction.
•
The Quick Disconnect MUST BE installed above
ground.
•
WARNING: Do not route the 10 foot Quick
Disconnect Hose under a deck. The hose must
be visible and inspected prior to each grill use.
Figure 1
(For Natural Gas Model Only)
If the length of line required does not exceed 50 feet, use
a 5/8" O.D. tube. One size larger should be used for
lengths greater than 50 feet.
Gas piping may be copper tubing, type K or L; polyeth-
ylene plastic tube, with a minimum wall thickness of .
062 inch; or standard weight (schedule 40) steel or
wrought iron pipe.
Copper tubing must be tin-lined if the gas contains more
than 0.3 grams of hydrogen sulfide per 100 cubic feet
of gas.
Plastic tubing is suitable only for outdoor, underground
use.
Gas piping in contact with earth, or any other material
which may corrode the piping, must be protected
against corrosion in an approved manner.
Underground piping must have a minimum of 18"
cover.
Gas Line Piping
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for gas
leaks. This will result in a fire or explosion
which can cause serious bodily injury or
death, and damage to property.
DANGER!
NATURAL GAS SUPPLY
QUICK
DISCONNECT
I
N
S
I
D
E
W
A
L
L
O
U
T
S
I
D
EW
A
L
L
MALE
FITTING
TO NATURAL GAS
REGULATOR
LOCKING GAS
SHUT OFF VALVE
LOCKING
GAS
SHUT OFF
VALVE
Additional
Hardware Not
Included
All connections and joints must be thoroughly tested
for leaks in accordance with local codes and all listed
procedures in the latest edition of ANSI Z21.58a-2006
Test Connections
/CSA1.6a-2006
5
Carefully lift each Burner up and away from the
Gas Valve Orifice, then refer to Figure 1 and
perform one of these three cleaning methods:
Before Using Your Grill
Bend a stiff wire, (a lightweight coat hanger
works well) into a small hook as shown
below. Run the hook through the Burner
Tube and inside the Burner several times to
remove any debris.
Use a Burner Cleaning Brush, or a bottle
brush with a flexible handle. Run the brush
through the Burner Tube and inside the
Burner several times, removing any debris.
Use an air hose to force air through each
Burner Tube. The forced air should pass
debris or obstructions through the Burner
and out the ports.
1.
2.
3.
The location of the Burner Tube with respect
to the Orifice is vital for safe operation. Check
to ensure the Orifice is inside the Burner Tube
before using your gas grill. See Figure 2.Ifthe
orifice is not inside the burner tube, lighting the
Burner may cause explosion and/or fire.
Figure 2
WARNING
!
Assembly Instructions For Your Safety
During unpacking, assembly and construction
stages always wear work gloves and eye
protection.
As you unpack this gas grill from shipping
box, use the parts list to ensure all neces-
sary parts are included. Inspect all parts for
damage as you proceed. Do not operate your
grill if it appears damage. If you have ques-
tions during the assembly process, call
8:00am - 5:00pm EST, Monday through Friday,
1-800-667-7313
Remove white PVC protective film from stain-
less steel surfaces before initial use.
CAUTION:
While it is possible for one person to unpack
this gas grill, obtain assistance from another
person when handing the large and heavy
grill head.
CAUTION: Spiders and small insects occasion-
ally spin webs or make nests in the grill burner
tubes during transit and warehousing. These webs
can lead to a gas flow obstruction which could
result in a fire in and around the Burner Tubes.
This type of fire is known as a "FLASHBACK"
and can cause serious damage to your grill and
create an unsafe operating condition for the user.
Although an obstructed Burner Tube is not the
only cause of "FLASHBACK", it is the most
common cause.
To reduce the chance of "FLASHBACK", you
must clean the Burner Tubes before assembling
your grill, and at least once a month in late
summer or early fall when spiders are most active.
Also perform this Burner Tube cleaning procedure
if your grill has not been used for an extended
period of time.
CAUTION: BEWARE OF FLASHBACK
Tools Required for Assembly
•
Open-end wrench (included with Hardware
Pack) used to tighten the Casters.
Figure 2
Figure 1
Figure 2
Burner
Gas Valve Assembly
Orifice
Burner Tube
•
Phillips Head screw driver - also used to
remove the screws from the rear of each
burner when cleaning the Burners
To reduce the chance of "FLASHBACK" (see
CAUTION at left) clean the Burner Tubes and
Burners before fully assembling your grill. Re-
move the screws at the rear of each burner using
a Phillips Head Screwdriver.
6
Contents for Hardware Pack (Part #P4182A)
Contents for Hardware Pack (Part #P4182A)
Contents for Hardware Pack
The following table illustrates a breakdown of the Hardware Pack. It highlights what components
are used in the various stages of assembly.
4
4
4
4
4
8
4
4
4
8
4
2
2
4
4
4
8
8
1
2
2
1
1
1
1
1
1
1
2
Component Qty
Purpose of Components
1/4" x 1/2" Phillips Head Screw
1/4" Lock Nut
1/4" Washer
1/4" x 1/2" Phillips Head Screw
1/4" Lock Nut
1/4" x 1/2" Phillips Head Screw
1/4" x 1/2" Phillips Head Screw
1/4" Lock Nut
1/4" Washer
1/4" x 2- 1/2" Phillips Head Screw
3/16" x 3/8" Phillips Head Screw
1/4" x 1/2" Phillips Head Screw
3/16" x 3/8" Phillips Head Screw
3/16" x 1/4" Phillips Head Screw
1/4" x 2- 1/2" Phillips Head Screw
1/4" Lock Nut
3/16" x 3/8" Phillips Head Screw
1/4" x 1/2" Phillips Head Screw
M4 x 10 Self Tapping Screw
3/16" x 3/8" Phillips Head Screw
3/16" Lock Nut
Side Burner Control Knob
Spring
Side Burner Control Knob Seat
Lighting Stick
Customized Wrench
Hose Holder
Lid Knob
3/16" x 1/4" Phillips Head Screw
Attaches Bowl Bracket to Bowl Side Panel
Secures Side Shelf and Side Shelf Bracket
Attaches Side Shelf Bracket to Cart Legs
Attaches Side Shelf to Bowl Side Panel
Attaches Cart Legs to Bottom Shelf
Attaches Cart Rear Panel to Cart Legs
Attaches Door Bracket to Cart Legs
Attaches Door Stop to Bottom Shelf
Secures Door Handle to Door Plate
Secures Cart Legs to Grill Bowl
Attaches Cart Side Panel to Cart Legs
Attaches Bowl Bracket to Cart Legs
Attaches Lighting Stick to Grill Bowl
Attaches Hose Holder to Cart Side Panel
Attaches on Side Burner Valve
Attaches on Side Burner Valve
Attaches on Side Burner Valve
Attaches on RR Cart Leg
Tighten Caster
Secures Regulator Hose on the Cart Side Panel
Attaches on Side Burner Lid
Install NG Regulator Assembly
(For NG Model only)
4
4
1/4" x 1/2" Phillips Head Screw
Attaches Tank Holder to Cart
1/4" Lock Nut
7
Contents for Hardware Pack (Part #P4182A)
Contents for Hardware Pack (Part #P4182A)
Contents for Hardware Pack P06021001B(LP) & P06021021B(NG)
Quantity of Each Hardware Piece:
Grill Information Center:
If you have questions about assembly or grill operation, or if there are
damaged or missing parts when you unpack this unit from the shipping boxes, call us
8:00am - 5:00 pm EST, Monday through Friday at:
1-800-667-7313
1/4" x 2 1/2" Phillips Head Screw
QTY: 12
1/4" x 1/2"
Phillips Head Screw
QTY: 34
1/4" Lock Nut
QTY: 20
Manual Lighting Stick - QTY. 1
"AA" Battery - QTY. 1
Door Handle - QTY. 2
Caster Wrench - QTY. 1
3/16" x 3/8"
Phillips Head Screw
QTY: 16
3/16" Lock Nut
QTY: 2
M4 x 10
Self-Tapping Screw
QTY. 1
1/4" Washer
QTY. 8
3/16" x 1/4"
Phillips Head Screw
QTY. 4
Side Burner Control Knob
- QTY. 1
Side Burner Control Knob Seat
- QTY. 1
Spring - QTY. 1
Lid Knob- QTY. 1
Hose Holder- QTY. 1
3/16" x 1/4"
Phillips Head Screw
QTY. 2
(for NG Regulator
Bracket )
Hardware already installed in the Tank Tray
Wing Bolt 3/16"x1-1/2"
Qty. 1 (LPG model)
Part # S233G03241
Scale 1:2
8
SS64PartsDiagram
Remove all components from the cartons and place within easy reach. Turn carton upside
down and it will provide a comfortable height work surface for grill assembly.
23
55
57
60
28-1
35
34
32
42
37
43
41
40
31
33
38
39
61
28
13
51
19
26
58
59
56
25
30
29
36
21
24-1
62
27
20
52
54
53
23
22
24
44
15
18
50
17
16
14
11
45
47
12
46
10
8
7
9
48
49
2
5
6
3
4
1
66
65
67
64
38(NG Only)
68
69
63
70
71
9
SS64 Parts List
QTY.REF# PART#DESCRIPTION
For the repair or replacement parts you need:
Call our Customer Service Dept., 8am - 5pm EST,
Monday through Friday at 1-800-667-7313
To make sure you obtain the correct replacement part
(s) for your gas grill please refer to the parts list on
this page. The following information is required to
insure you receive the correct parts:
1. Model and Serial Number (see CSA label on grill)
2. Part Number
3. Description
4. Quantity of parts needed
Please allow sufficient time to process and ship.
IMPORTANT: Keep this Owner's Manual for
convenient referral and for part replacement.
IMPORTANT: Use only factory authorized parts. The
use of any part that is not factory authorized can
be dangerous. This will also void your warranty.
QTY.REF# PART#DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
24-1.
25.
26.
27.
28.
28-1.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
1
1
1
1
1
2
3
3
3
1
1
1
1
1
1
2
2
1
1
1
1
4
5
4
1
1
1
1
2
2
1
1
1
1
1
4
4
1
2
1
1
1
2
1
1
1
1
1
1
Lid Plate
Heat Gauge
Name Plate
Lid Handle
Warming Rack
Cooking Grid
Flame Tamer
Gas collector with Electrode
Main Burner
Burner Bracket
Grease Tray Heat Shield, Upper
Bowl Panel, Left
Bowl Panel, Rear
Bowl Panel, Right
Bowl Panel, Front
Lid Hinge
Bowl Bracket
Electric Wire Set
Gas Valve/ Manifold Assembly
(LPG)
(NG)
Gas Fitting
Control Panel
(LPG)
(NG)
Control Knob Seat
Spring
Main Burner Control Knob
Back Burner Control Knob
Ignitor - 4 port
Battery
Grease Tray
Side Shelf Bracket-A
Side Shelf Bracket-B
Hose Holder (LPG only)
Cart Leg,LR
(LPG)
(NG)
Cart Leg,LF
Cart Leg,RR
Cart Leg,RF
Caster Seat
Caster
Cart Rear Panel
Cart Side Panel
Bottom Shelf
(LPG)
(NG)
Door Stop
Door Bracket
Door Handle
Door Panel, Left
Door Panel, Right
LPG Regulator
Back Burner Assembly
Back Burner Electrode
Back Burner Wind Shield
P0011819EA
P00601061A
P00407005C
P00205049B
P01505005G
P01615015A
P02008024A
P06903019B
P0072009JA
P0072513FA
P0072109JA
P0073813FA
P05501005F
P01306013F
P02615018A
Y0060117
Y0060217
P03906002A
P0290724DP
P0290724DQ
P03413011J
P05504001A
P02502024C
P05301001A
P02705075B
P01204001B
P01206001B
P05536001P
P00911009E
P00911029E
P00910009E
P00913009E
P00912009E
P04507001A
P05112002A
P07702024D
P07604007G
P01002009L
P01002039L
P05510009P
P03301013F
P00201001C
P04302019A
P04303019A
P03601003A
Y0310015
P02610005B
P06905009A
Back Burner Orifice
(LPG)
(NG)
Back Burner Extension Tube
Side Shelf, Right
Side Burner Frame
Side Burner Lid
Side Burner Lid Handle
Pot Support
Side Burner
Side Burner Electrode
Side Burner Control Knob
Side Burner Control Knob Seat
Side Burner Gas Valve
(LPG)
(NG)
Connection Hose
(LPG)
(NG)
Lighting Stick
Grease Tray Heat Shield, Lower
Tank Holder
NG Regulator
Extension Hose (NG only)
Hose, 10ft. / NG
NG Regulator Bracket
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P06520003A
P06520013A
P03701004A
P01103006F
P02302004F
P01127003F
P00201002F
P00805002F
P02002007A
P02614007C
P03408051J
Y0060127
Y0060227
P03705014A
P03705043A
P05507031E
P06903021B
P05359001A
Y0080007
P03705044F
P03703002A
P03328018A
CSA Label
EI Protective Bracket
68.
1
P03328048Q
Weight
69.
1
P05344003Q
P03428083H
P03428093H
P03401103H
70.
1
71.
1
Back Burner Thermocouple
Back Burner Thermocouple
Backet
P05305023A
P03328049A
P01708004A
P02609009M
P0220505ED
10
Rotisserie Parts Diagram Y0250098
Rot. Collar
Rot. Spit
Rot. Holding Fork
Rot. Motor Bracket
Rot. Motor/AC
Rot. Screw #10-24x3/4"
Rot. Washer
Rot. Nut #10-24
Rot. Thumbscrew 1/4"x1/2"
1.
2.
3.
4.
5.
6.
7.
8.
9.
1
1
2
1
1
2
2
2
2
P05508177F
P05508158F
P05508112F
P03307028A
P07101010A
S112G10124
S411G03084
S362G10124
S196G04084
Rot. Screw#10-24x3/4"
UNC
QTY. 2
Ref.# S112G10124
QTY.REF# PART#DESCRIPTION
Rotisserie Parts List Hardware for Rotisserie
Rot.Washer
QTY. 2
Ref.# S411G03084
Rot. Nut.#10-24
QTY. 2
Ref.# S362G10124
Rot.Thumbscrew
1/4"x1/2"
QTY. 2
Ref.# S196G04084
5
6
7
8
4
9
9
3
2
1
11
Cart Assembly Instructions
Remove all cart parts, hardware, and Grill Head from
shipping boxes. Raise the Grill Lid and remove all
packed components. Use the parts list to check that
all necessary parts have been included.
Assemble the gas grill on a protective work surface
to avoid scratching grill surfaces. Inspect your grill for
damage as you proceed. Do not assemble or operate
your grill if it appears damaged.
Assembling The Cart
Position bottom shelf with tank toward the left
side.See Figure 1.
Note: The label on the cart legs indicate their
assembly position to the bottom shelf. LF=Left
Front, LR=Left Rear, RF=Rear Front, and
RR= Right Rear. Labels should face inward
toward each other when correctly assembled.
Remaining components cannot be assembled if
leg postions are incorrect.
Install the four cart legs to the indicated corners
of the bottom shelf using 8 of the 1/4" x 2-1/2"
Phillips Head screws provided. Do not fully tighten
screws.
Install the two Cart Side Panels to the cart by using
4 of the 3/16" x 3/8" Phillips Head screws on each
panel. Leave side panel screws loose. See Figure
3.
Install the Cart Rear Panel to the cart
by using 4 of the 3/16" x 3/8" Phillips Head screws.
1/4" x 2-1/2" Phillips Head Screw x 8
3/16" x 3/8" Phillips Head Screw x 8
Figure 1
Figure 2
Figure 3
BOTTOM
SHELF
CART LEG
(LR)
CART LEG
(LF)
CART LEG
(RF)
CASTER
CART SIDE
PANEL
CART REAR
PANEL
CART LEG
(RR)
3/16" x 3/8" Phillips Head Screw x 4
5.
4.
2.
1.
Screw the 4 Casters into the caster seats in the
bottom of each cart leg. Turn the threaded caster
stem by hand, clockwise until it stops. Fully tighten
with the wrench provided. See Figure 2.
3.
12
9.
6.
8.
Attach the Door Bracket to the low holes in the
front legs with the end tabs pointing upward and
flange to the rear, pointing downward. Use 2 of
1/4" x 1/2" Phillips Head Screws. Do not fully
tighten. See Figure 4.
Attach the Door Stop to the bottom shelf, with
the flange facing the front, using 2 of
3/16" x 3/8" Phillips Head Screws. Fully tighten.
See Figure 4.
Place doors into the hinge holes of the bottom shelf
and Door Bracket. Push Door Bracket down until
doors are secure and can open and close freely.
Do not full tighten Door Bracket screws. See
Figure 4.
Remove protective film from Doors. Install Door
Handle to Doors using 4 of 3/16" x 1/4" Phillips Head
Screws. See Figure 4.
10.
1/4" x 1/2" Phillips Head Screw x 2
3/16" x 3/8" Phillips Head Screw x 2
Figure 4
Figure 5
DOOR
HANDLE
DOOR BRACKET
DOOR PLATE
3/16" x 1/4"
Phillips Head Screw x 4
DOOR STOP
LIGHTING
STICK
BOWL SIDE PANEL
BOWL BRACKET
BOWL SIDE PANEL
BOWL BRACKET
Phillips Head Screw
1/4'' x 1/2"
Qty. 4
Part # S
Flange Nut 1/4"
Qty. 4
Part # S
Tank Holder
Align the 4 holes (2 on either side) of the Tank
Holder Bracket with the holes on the Cart Bottom
Shelf and insert 4 Phillips Head Screws
1/4'’ x1/2'’ as shown.
From the underside of the Cart Bottom Shelf
secure with 4 Flange Nuts 1/4'’.
Note: Be sure to remove preassembled Wing
Bolt on the Tank Holder, unclamp the 2 Arm
Rims where they meet before installing the gas
tank into p ositon and then reclamp the 2 Arm
Rims parts together and secure gas tank
using the Wing Bolt.
7.
Attach the 2 Bowl Brackets to Bowl Side Panel
using 4 of 1/4" x 1/2" Phillip Head Screw, 1/4" Nuts
and 1/4" Washers. Fully tighten. See Figure 5.
1/4" x 1/2" Phillips Head Screw x 4
1/4" Lock Nut x 4
11.
1/4" Washer x 4
Attach lighting stick to the Right Rear Leg, below
side shelf bracket using 1 M4 x 10 self-tapping
screw.
10.
M4 x 10 Self-Tapping Screw x 1
13
14
12.
13.
Grill Head Assembly
14.
Put the grill head onto cart. Secure grill head to
all cart legs using 4 of 1/4" x 2-1/2" Phillips Head
Screws and 1/4" Nuts. See Figure 6,7.
Secure Bowl Bracket to Cart Legs using 4 of 1/
4" x 1/2" Phillips Head Screws. Repeat this step
for the other side. See Figure 7.
Fully tighten all leg screw, Side Panel Screws,
Door Bracket screws and grill head screws.From
the back of the cart, slide the grease draining tray
into the grill head. See Figure 7.
Attach the Side Shelf Brackets to Cart Leg using
8 of 1/4" x 1/2" Phillips Head Screws. See Figure
8.
Place the Side Shelves over the Side Shelf
brackets. Secure firmly using 4 of 1/4" x 1/2"
Phillips Head Screws and 1/4" Lock Nuts.See
Figure 8.
Align the Side Shelf holes to Bowl Side Panel and
Side Shelf Bracke. Secure firmly by using 1/4"
x 1/2" Phillips Head Screws, 1/4" Nuts and 1/4"
Washer. See Figure 9.
15.
16.
1/4" Lock Nut x 4
Figure 6
Figure 8
Figure 7
1/4" x 2-1/2" Phillips Head Screw x 4
1/4" Lock Nut x 4
1/4" x 1/2" Phillips Head Screw x 8
1/4" x 1/2" Phillips Head Screw x 8
1/4" x 1/2" Phillips
Head Screw x 4
1/4" Lock Nut x 4
GRILL BOWL
BOWL BRACKET
SIDE SHELF BRACKET
SIDE SHELF
1/4" x 1/2" Phillips
Head Screw x 4
Figure 9
17.
SIDE SHELF
BOWL SIDE PANEL
1/4" Washer x
4
GREASE TRAY
15
Side Burner Assembly
Insert the Orifice into the Side Burner Tube.
Attach the Side Burner Gas Valve to Side Shelf
Left. Secure firmly using 2 of M4 x 10mm Phillips
Head Screws (Attach on Side Burner Gas Valve).
Attach the Side Burner Electrode Wire to the
Control Valve.See Figure 10,11.
Install the Lid Knob using 1 of 3/16" x 3/8" Phillips
Head Screw (attaches on Lid Knob).See Figure
10.
Attach the chrome color Control Knob Seat and
Spring onto the Gas Valve stem. Then, carefully
attach the Control Knob so the "OFF" position
faces upward - toward you. Do not force the Control
Knob onto the stem. See Figure 12.
Place the LPG Regulator inside the cart through
the opening above Cart Side Panel. Press the hose
of the LPG Regulator into the Hose Holder above
Cart Side Panel. Secure firmly using 2 of 3/16"
x 3/8" Phillips Head Screw and 3/16" Nut. See
Figure 13.
3/16" x 3/8" Phillips Head Screw
Figure 10
Figure 11
Figure 12
The location of the Burner Tube with respect to
the Orifice is vital for safe operation. Check to
ensure the Orifice is inside of the Burner Tube
as shown below, before using your gas grill. If
the Burner Tube does not fit over the Valve
Orifice, lighting the Burner may cause an explo-
sion and/or fire. Figure 3A
WARNING!
ORIFICE
GAS VALVE
Burner Tube
Figure 13
18.
19.
20.
21.
LID KNOB
SIDE BURNER
GAS VALVE
SIDE BURNER
GAS VALVE
ORIFICE
SIDE BURNER
TUBE
ELECTRODE
WIRE
CONTROL
KNOB
SPRING
CONTROL
KNOB SEAT
HOSE
LPG REGULA-
TOR
HOSE HOLDER
CART SIDE
PANEL
3/16" Lock Nut x 2
3/16" x 3/8"
Phillips Head Screw x 2
16
For Natural Gas Models attach the Regulator
Bracket to Left Rear Cart Leg using 2 of 3/16”
x1/4” Phillips Head Screws.
Regulator Assembly(NG Only)
3/16" x 1/4"
Phillips Head Screw
QTY. 2
EXTENSION
HOSE
REGULATOR ASSEMBLY / NG
REGULATOR
BRACKET
LEFT REAR
CART LEG
17
Requires and assistant:
Before placing the cooking components into your grill,
insure that the Spark Electrode Tip is properly positioned
within each Gas Collector Box (stainless steel mecha-
nism found at the front between each set of Burners.)
The easiest way to insure this is to perform this Electrode
Check:
1. Be sure all Control Knobs are set to "OFF"
and open the Grill Lid.
2. Have an assistant stand behind to the right of
the grill and look down at each Gas Collector
Box. NEVER put your face inside Grill Head.
3. Push Ignition Cap. You should hear a clicking
sound and your assistant should see a small
blue spark within each Gas Collector Box.
If a spark is present the Electrode Tips are
properly positioned.
4. If no spark is seen the Spark Gap shown in
Figure 15 needs to be adjusted as follows:
•
Using an adjustable wrench, loosen the inside
Nut just until the Gas Collector Box can be
maneuvered and turned upward.
•
The gap between the Spark Electrode Tip and
Spark receiver should be approximately 3/16".
•
If the gap is wider than 3/16" use a pair of long
hose pliers and gently squeeze the Gas
Collector Box until the gap is correct.
•
Return the Gas Collector Box to its original
horizontal position, secure the inside Nut and try
the Electrode Check again.
5. If no "clicking" sound is heard check the
following common causes. If you need
assistance call our Grill Information Center
at 1-800-667-7313.
•
Ignitor AA battery not installed properly.
•
Ignitor wires may be loose. Remove the AA
battery, inspect the Ignitor Junction Box
found behind the Control Panel, and connect
any loose wires.
Ignitor Battery Installation - See Figure 14
1. Unscrew the Ignitor Cap located on the Grill Control
Panel and remove the Contact and Spring from the
Ignitor Slot.
2. Place the manufacturer supplied AA battery into the
Ignitor Slot. Be sure to place the positive pole facing
toward you.
3. Place the Spring over the AA battery, then place
the Contact on top of the Spring. Screw the Ignitor
Cap back onto the grill Control Panel.
Grill Information Center:
If you have questions about assembly or grill operation, or if there are
damaged or missing parts when you unpack this unit from the shipping boxes, call us
8:00am - 5:00 pm EST, Monday through Friday at:
1-800-667-7313
Electrode Check
Figure 14
Figure 15 - Side View Gas Collector Box
INSIDE
NUT
SPARK
ELECTRODE TIP
SPARK GAP
+
IGNITOR SLOT
AA BATTERY
IGNITOR CAP
18
CAUTION: When the appliance is not in use, the
gas must be turned off at the supply tank.
Place the Flame Tamers on the lower ledge above
Burners. See Figure 16. Place 3 of Flame Tamers
onto the Rack.
Place Cooking Grids on the ledge above Flame
Tamers.
Place Warming Rack into the slot on the upper
left and upper right of the grill bowl panels. See
Figure 16.
IMPORTANT: The Grill is not designed for use with
lava rock or briquettes and the use of such items
will void the warranty.
1.
Installing Cooking Components
2.
Connecting A Liquid Propane Gas (LP gas)
Tank To Your Grill
1. Check the Tank Valve to insure it has proper
external mating threads to fit the Hose and
Regulator Assembly provided. (Type 1
connection per ANSI Z21.58b-2002)
2. Inspect the Valve Connection Port and
Regulator assembly. Look for damage or debris.
Remove any debris. Inspect Hose for damage.
Never use damaged or plugged equipment.
3. Hang your filled gas tank on the Tank Hole.
4. Make sure all Burner Valves are in the OFF
position.
5. When connecting the Hose and Regulator
Assembly to the Tank Valve, hand tighten nut
clockwise to a full stop. Do Not use a wrench
to tighten because it could damage the Quick
Coupling Nut and result in a hazardous
condition.
Disconnecting A Liquid Propane Gas (LP gas)
Tank From Your Grill
Turn the Burner Valves and LP Gas Tank Valve
to the full OFF position (turn clockwise to
close).
Detach the Hose and Regulator Assembly from
the LP gas Tank Valve by turning the Quick
Coupling Nut counterclockwise.
1.
2.
3.
Figure 16
TANK HOLE
Figure 17
TYPE 1
CONNECTION
PER ANSI Z21.
58b-2002
FLAME
TAMERS
Theseholes arefor
Rotisserie Mount-
ing Bracket use
WARMING RACK
Cooking Grid
6. Slowly open the tank valve 1
/4 to 1/2 open
(counterclockwise). Use a soapy water solution
to check all connections for leaks before
attempting to light your grill. See "Checking
for Gas Leaks" on page 19. If a leak is found,
turn the Tank Valve off and do not use your
grill until the leak is repaired. Do this leak test
even if the grill was store assembled.
Congratulations
Your Grill Chef gas grill is now ready for use.
Before the first use and at the beginning of each
season (and whenever a LP gas tank
has been changed):
1.
2.
3.
Read all safety, lighting and operating
instructions.
Check Gas Valve Orifices, Burner Tubes and
Burner Ports for any obstructions.
Perform gas leak check according to
instructions found on page 19 of this
Owner's Manual.
19
Set control knobs to OFF and open the LP gas
tank valve slowly until 1/4 to 1/2 open.
Push and turn the RIGHT control knob to HIGH/ .
Immediately press the electric ignitor for 3-4
seconds to light the burner.
If the burner does not light, turn the control knob to
OFF, wait 5 minutes for gas to clear, then retry.
Adjust control knobs to your desired cooking
temperature.
Checking For Gas Leaks
Never test for leaks with a flame. Prior to first use,
at the beginning of each season, or every time your
LP gas tank is changed, you must check for gas leaks.
Follow these four steps:
3.
4.
Apply the soap solution to all gas connections.
If bubbles appear in the soap solution the con-
nections are not properly sealed. Check each
fitting and tighten or repair as necessary.
If you have a gas leak that you cannot repair,
turn off the gas at the source, disconnect fuel line
from your grill and call 1-800-667-7313 or your gas
supplier for repair assistance.
1.
2.
Make a soap solution by mixing one part liquid
detergent and one part water.
Turn the grill Control Knobs to the full OFF
position, then turn the gas ON at source.
Grill Lighting Instructions
Basic Lighting Procedures
Familiarize yourself with the safety guidelines
at the front of this manual. Do not smoke
while lighting grill or checking gas supply
connections.
Be sure the LP gas tank is filled.
Check that the end of each Burner Tube is
properly located over each valve orifice.
Make sure all gas connections are securely
tightened..
Open the Grill Lid.
1.
2.
3.
4.
WARNING
!
• Shut off gas supply to the gas grill.
• Turn the Control Knobs to OFF position.
• Put out any flame with a fire extinguisher.
• Open Grill Lid.
• Get away from the LP gas tank.
• Do not try to fix the problem yourself.
• If odor continues or you have a fire you
cannot extinguish, call your fire department.
Do not call near the LP gas tank because
your telephone is an electrical device and
could create a spark resulting in fire and/
or explosion.
A strong gas smell, or the hissing sound of gas
indicates a serious problem with your gas grill
or the LP gas tank. Failure to immediately follow
the steps listed below could result in a fire or
explosion that could cause serious bodily injury,
death, or property damage.
NOTE: The normal flow of gas through the
regulator and hose assembly can create a
humming nosie. A low volume of nosie is
perfectly normal and will not interfere with
operation of the grill. If humming nosie is
loud and excessive you may need to purge
air from the gas line or reset the regulator
excess gas flow device. This purging
procedure should be done every time a new
LP gas tank is connected to your grill. For
help call the Customer Service Helpline for
assistance.
WARNING
Failure to open Grill Lid during the lighting
procedures could result in a fire or explosion
that could cause serious bodily injury, death,
or property damage.
!
6.
7.
8.
9.
10.
Customer Service Helpline, 8:00am - 5:00
pm EST, Monday through Friday at
1-800-667-7313.
5.
OFF
HIGH
OFF
Open LP
gas tank
11.
PRESS
ELECTRIC
IGNITOR
Repeat steps to light each burner individually
20
Manually Lighting Your Grill by Match
To light your gas grill by match, insert a match into the
Manual Lighting Stick and follow steps 1 through 6 of the
Basic Lighting Procedures. Then, light the match and
place Manual Lighting Stick through the Lighting Hole on
the right side of the grill. See Figure 18. Turn the nearest
Main Burner Control Knob to the HIGH setting to release
gas. The Burner should light immediately.
To purge air from your gas line and/or reset
the Regulator excess gas flow device:
Opening the tank valve all the way or too quickly is
what triggers the Regulators safety device to shut
down gas flow which prevents excessive gas flow to
your grill. Lighting the Burner farthest from the fuel
source every time will help eliminate air pockets in
the Manifold. This procedure should be done every
time a new LP gas tank is connected to your grill:
Never lean over the grill cooking area while
lighting your gas grill. Keep your face and body
a safe distance (at least 18 inches) from the
Lighting Hole or Burners, when lighting your grill
by match.
WARNING
!
•
•
2.
3.
Misalignment of Burner Tubes over Orifices
Correction: Reposition Burner Tubes over Orifices.
Obstruction in gas line
Correction: Remove fuel line from grill. Do not smoke!
Open gas supply for one second to clear any
obstruction from fuel line. Close off gas supply at source
and reconnect fuel line to grill.
If an obstruction is suspected in Gas Valves or Gas
Valve Bracket, please call the Customer Service
Dept. at 1-800-667-7313.
Turn gas off at source and turn the Control Knobs
to OFF. Wait at least five minutes for gas to clear,
then retry.
Check gas supply and connections.
Repeat lighting procedure. If your grill still fails to
operate properly, turn the gas off at source, turn the
Control Knobs to OFF, then check the following:
If the grill fails to light properly:
1.
•
•
Disconnected Ignition Wires
Correction: Inspect the Ignitor Junction Box
found behind the Control Panel. Connect loose
Ignitor wires to Junction Box and try to light
grill.
Weak AA battery
Correction: Unscrew the Ignitor Cap and replace
the battery.
Figure. 18
Turn all Control Knobs to the OFF position.
Turn off the LP gas tank valve at the tank
valve.
Disconnect Regulator from LP gas tank.
Let unit stand for 5 minutes.
Reconnect Regulator to the LP gas tank.
Open Grill Lid or Side Burner Lid.
Turn the LP gas tank valve on s
lowly until
1/4 to 1/2 open.
L
ight the Burner farthest from fuel source
by turning its Control Knob to IGN then
pushing in the Control Knob. To light the
Side Burner push its Control Knob in and
turn to HIGH.
LIGHTING
HOLE
MANUAL
LIGHTING
STICK
MATCH
•
Plugged Orifice
Correction: Remove Burners from grill by removing
the screws using a Phillips Head Screwdriver.
Carefully lift each Burner up and away
from Gas Valve Orifice. Remove the Orifice from
Gas Valve and gently clear any obstruction with
a fine wire. Then reinstall all Orifices, Burners,
Burner Screws and cooking components.
•
Misalignment of Ignitor on Burner
Correction: Check for proper position of the
Electrode Tip as shown on page 17. The gap
between the Spark Electrode Tip and Spark
Receiver should be approximately 3/16".
Adjust if necessary following the Electrode
Check procedure on page 17.
• Shut off gas supply to the gas grill.
• Turn the Control Knobs to OFF position.
• Put out any flame with a Class B fire
extinguisher.
• Open Grill Lid.
• Once the grill has cooled down, clean
the Burner Tubes and Burners according
to the cleaning instructions found on
page 25 in this manual.
Should a "FLASH-BACK" fire occur in/or
around the Burner Tubes, follow the
instructions below. Failure to comply with
these instructions could result in a fire or
explosion that could cause serious bodily
injury, death, or property damage.
WARNING
!
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Patio Chef SS64LP Owner's manual
- Category
- Barbecues & grills
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Home Decorators Collection checking User guide
-
Bakers & Chefs 9905TB-LPG Owner's manual
-
Monument 14633 Owner's manual
-
Cambridge Casual HD-590170 Installation guide
-
Bull LP 69101 Operating instructions
-
Charbroil 463831004 Owner's manual
-
Charbroil 463840604 Owner's manual
-
Summit DW18SS2 Custom Panel Installation
-
-
Sunbeam Y0003CW Owner's manual
