Page is loading ...
ACCESSORIES
OPTIONS
● Key locking device (A) mounted on adjustment knob
- supplied installed on regulator, code: 662 554
-
supplied alone, separately from the regulator, code: 343 03 050
Note: in the second case, the regulator must be designed
to receive the device. An option code: 662 551 to the code
of the joinable regulator selected.
● Adjustment range 0.5 to 12 bar (provide for 50 mm dia. 0-16 bar
pressure gauge)
● Two-piece assembly kit, code: 343 03 001
● Lateral mounting brackets, code: 343 03 003
● Upper mounting ring, code: 343 00 004
● 50 mm dia. pressure gauge (0-12bar), code: 342 00 062
● 50 mm dia. pressure gauge (0-4bar), code: 342 00 061
● 50 mm dia. pressure gauge (0-16bar), code: 342 00 997
JOINABLE REGULATOR AIRFLOW
CHARACTERISTIC CURVE
TYPE: MODULAIR 112
Air flow
Outlet pressure
G 3/8 - G 1/2
0 1020304050607080
0
1
1
2
3
4
5
6
7
bar
1000
2000 4000 50000 3000
0
l/min
(ANR)
dm
3
/s
(ANR)
(A)
•
(A)
OPERATIONS TO BE PERFORMED BEFORE UTILISING
All joinable regulators include one G3/8 or G1/2 port on one side for connection of
the regulated outlet and a G1/8 port on the opposite side for the optional
connection of a pressure gauge (port concealed by cover plate trim)
●●
●●
●
Installation with pressure gauge
- Remove regulators with G1/8 port and trim on front
- Remove the trim
- Manually install the pressure gauge
●●
●●
●
Installation without pressure gauge
- Remove the trim
- Seal the plug supplied on G1/8 port with a suitable product.
- Reinstall the trim
- Choce of installation orientation with regulated outlet on front or side
●●
●●
●
Assembly / joinable
Easily joined to all Modulair 112 range devices by means of a joining system
accessible from the front
●●
●●
●
Connection of regulated outlet ports
- Orientate the regulators as per the above mounting option, then proceed to
connect the regulated output ports
●●
●●
●
Connection to pressure supply
- Supply connection at left-hand and/or right-hand side
-
Installation recommendation: A single pressure inlet can supply a set of five
regulators. If there are more than five, supply from both ends is necessary.
- Possibility of having supplies with two different pressures, by placing a blanking
plate at the appropriate point
ADJUSTMENT OF DOWNSTREAM PRESSURE
●●
●●
●
Available adjustment ranges:
0.5 to 10 bar / 0.2 to 3 bar / 0.5 to 12 bar
●●
●●
●
Maximum inlet pressure: 16 bar
●●
●●
●
Adjustment knob with "pull-turn-push" type
locking system
●●
●●
●
Key locking version (A) available to avoid inadvertent loss of
downstream pressure adjustment.
GENERAL SPECIFICATION
FLUID : Filtered or neutral gas or compressed air
PORTS : G3/8 - G1/2 (inlet ports G1/2)
MAX. INLET PRESSURE : 16 bar
ADJUSTMENT RANGE : 0.5 - 10 bar, 0.2 - 3 bar
AMBIENT TEMPERATURE : -10°C to +60°C
MAX. FLOW (Qv at 6.3 bar) : 3000 l/min (ANR)
HYSTERESIS : 0.2 bar
SOFT-RELIEVING REGULATOR
Series 342
Type: Modulair
Air service equipment
JOINABLE REGULATOR
Type MODULAIR 112
G 3/8 - G 1/2
l/min (ANR)
dm
3
/s (ANR)
Adjustment range: 0.5 - 10 bar
G3/8 G1/2 16 0,5-10 3000 50 50 342 03 766 342 03 764
G1/2 G1/2 16 0,5-10 3000 50 50 342 03 767 342 03 765
Adjustment range: 0.2 - 3 bar
G3/8 G1/2 16 0,2-3 3000 50 50 342 03 762 342 03 760
G1/2 G1/2 16 0,2-3 3000 50 50 342 03 763 342 03 761
WITH pressure gauge
WITHOUT pressure gauge
gauge
dia.
CODES
(1)
REGULATOR
CHOICE OF EQUIPMENT
(pressure gauge 0-4 bar)
CONSTRUCTION
Regulating device with a rolling diaphragm (very low hysteresis)
Core and seals of nitrile (NBR)
Body of painted zamak
Locking “Pull-Turn-Push” pressure control knob
One G1/8 port is provided for a pressure gauge on the side opposite the load port
INSTALLATION
Combined with separately ordered assembly kits.
Regulators can be installed in any position, mounting options:
- Direct mounting on support with two 5 mm dia. screws (screws not included)
- Mounting with two side brackets (see accessories)
- Panel mounting (37.5 mm dia.) with optional mounting rings (see accessories)
Max. flow
at 6.3 bar pressure setpoint
and
∆
P of 1 bar/setpoint
Pipe
size
Max. inlet
pressure
(bar)
(1) Assembly kits are not supplied with regulators, but must be ordered separately, code 343 03 001 (quantity: number of regulators minus 1)
Control
pressure
(bar)
FEATURES
● Joinable modular pressure regulator for supplying different circuits at
different pressures from a common supply
● Compact and economical directly joinable units
● No pipework or couplings between regulators
● High flow, low hysteresis
● Joinable to main supply line, any FRL or Modulair 112 type accessories,
an extension is quick and easy
POSSIBLE CONFIGURATIONS
● Supply connection at left-hand and/or right-hand side
● Possibility of having supplies with two different pressures,
by placing a blanking plate at the appropriate point
● Other configurations are possible, consult us
Outlet
Common
inlet
(pressure gauge 0-12 bar)
P
•
GB
● The joinable regulator exists in a version intended for use in potentially explosive
gaseous or dusty atmospheres in accordance with ATEX directive 94/9/EC. Startup
and maintenance are to be performed as detailed below.
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
Asco Series 342 Joinable Regulator Modulair 112 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Asco Series 342 Joinable Regulator Modulair 112 Manuale del proprietario
- français: Asco Series 342 Joinable Regulator Modulair 112 Le manuel du propriétaire
- español: Asco Series 342 Joinable Regulator Modulair 112 El manual del propietario
- Deutsch: Asco Series 342 Joinable Regulator Modulair 112 Bedienungsanleitung
Related papers
-
Asco Series 342 Mounting Ring and Bracket Owner's manual
-
-
-
-
-
