OWNER’S MANUAL
v_01_march_2017
MARK
VISION
A WORD FROM MARCO DE VIRGILIIS
Thank you for choosing a Markaudio product!
Markaudio is a division of Mark World dedicated to
pro audio sound reinforcement.
Building on the top-level reputation built up over
many years by our industry-leading brands Markbass
and DV Mark , Markaudio boasts the same high level
of innovation and engineering.
The result is groundbreaking sound quality, impressive
power, and innovative design.
Hope you will enjoy your new Markaudio P.A. system,
and we invite you to contact us any time with your
comments and questions, at [email protected].
Thanks again, and good music!
Marco De Virgiliis
INDEX
3
INTRODUCTION
4
AS SERIES CONTROL PANEL
6
TECHNICAL DETAILS
AS SERIES 802 S
7
TECHNICAL DETAILS
AS SERIES 102 S
8
AS SERIES size
9
ACCESSORIES
10
POWER REQUIREMENT / FUSE
3
INTRODUCTION
MarkAudio powered subwoofers offer great exibility, ultra-compact design and
exceptional low frequency reproduction.
The AS 802 S is an active 2 x 8” subwoofer with 500 watts of power.
The AS 102 S is an active 2 x 10” subwoofer with 500 watts of power.
AS series combines quality of sound and design with high operating efciency
of power amplier. They include a powerful MPT (Mark Proprietary Technology)
power amp with a precise and focused response on low frequencies and a quick
control of distorsion.
4
aS SERIES CONTROL PANEL
MASTER LEVEL (1)
This is the MASTER Volume level.
CLIP (2)
Clip indicator LED. This indicator allows you to visually monitor the volume level of the
loudspeaker. LED OFF: compressor/limiter is not engaged. LED ON for a few moments:
brief engaging of the compressor/limiter, inaudible to the ears - you are approaching
maximum power output, and the speakers
are being protected. LED ON: the audio signal is too high, and you should lower the
output level of your
audio source, or turn the level knob counterclockwise.
PHASE (3)
Phase inversion 0°- 180°. In some installations, the subwoofer may be out of phase with
the satellites. This switch allows you to reverse the phase of the subwoofer and align the
system;
ON (4)
Power status indicator LED;
RIGHT (5) and LEFT (8) INPUT XLR
Line XLR input, the XLR 3-pole female jack is electronically balanced (hot pole: #2). You
can use unbalanced sources only if your cables have pole 3 jumpered to pole 1. Important:
when powering up, turn on your sound source (CD player and mixer, for example) before
turning on the Markaudio cabinets. When powering off, turn the cabinets off rst;
RIGHT (6) and LEFT (9) GROUND LIFT
These switches may be needed for the cancellation of hum due to ground loops with
other apparatuses;
RIGHT (7) and LEFT (10) LINK XLR
Line out to connect more subwoofers downstream from the principal system. This 3-pole
male XLR jack receives a female XLR plug (7) and sends out a passive signal;
1
9
2 4
6
85 7
3
10
5
COOLING (11)
Forced ventilation stabilizes the working temperature of electronic components
for continuous performance, even after a long period of operation. Avoid using the
loudspeaker on irregular surfaces that might block the vents;
AC POWER SOCKET (12)
VDE power jack for connecting the power cable from the unit to a wall power source. Make
sure the unit is grounded; all three terminals of the AC power plug must be connected to
avoid any injury to the user or damage to the unit.
Markaudio powered speakers and amps are manufactured to be used in the country
where they have been sold, and are factory preset to that country’s voltage. So make
sure you’re sending the correct voltage to your amp before you connect it to AC power.
FUSE (13)
Fuse housing;
ON/OFF SWITCH (14)
On/off power switch.
11
12
13
14
6
TECHNICAL DETAILS
AS 802 S
ACOUSTICAL SPECIFICATIONS
Frequency response: 40 Hz- 150 Hz
Max SPL: 130 dB
Woofer: 2 x 8”, 4 Ohm
INPUT/OUTPUT SECTION
Input connectors: stereo XLR female
Output connectors: stereo XLR male
Input sensitivity: +1.8 dBu (@70 Hz)
DSP PROCESSOR SECTION
Protections: Thermal, rms
Limiter: Soft limiter
Controls: Volume, Phas
AMPLIFIER
Low frequencies Power: 1000 W PEAK (@ 4 Ohm)
Low frequencies Power: 500 W RMS (@ 4 Ohm)
Cooling: Convection
Power Connection: VDE connector
CABINET
Cabinet Material: multiply poplar
Handles: 1 top
Pole Mount/Cap: Yes (M20 thread)
Colour: Black
PHYSICAL
Weight: 35.3 lbs / 16 Kg
Width: 11 in. /28.1 cm
Depth: 20 in. / 52 cm
Height: 20 in. / 52 cm
7
TECHNICAL DETAILS
AS 102 S
ACOUSTICAL SPECIFICATIONS
Frequency response: 40 Hz- 100 Hz
Max SPL: 132 dB
Woofer: 2 x 10”, 4 Ohm
INPUT/OUTPUT SECTION
Input connectors: stereo XLR female
Output connectors: stereo XLR male
Input sensitivity: +1.8 dBu (@70 Hz)
DSP PROCESSOR SECTION
Protections: Thermal, rms
Limiter: Soft limiter
Controls: Volume, Phase
AMPLIFIER
Low frequencies Power: 1000 W PEAK (@ 4 Ohm)
Low frequencies Power: 500 W RMS (@ 4 Ohm)
Cooling: Convection
Power Connection: VDE connector
CABINET
Cabinet Material: multiply poplar
Handles: 2 side
Pole Mount/Cap: Yes (M20 thread)
Colour: Black
PHYSICAL
Weight: 50.7 lbs / 23 Kg
Width: 17 in. / 43 cm
Depth: 19 in. / 48 cm
Height: 29.3 in. / 74.5 cm
8
AS 802 S
AS 102 S
AS SYSTEMs size
mm
WEIGHT:
Weight: 16 Kg / 35.3 lbs
WEIGHT:
Weight: 23 Kg / 50.7 lbs
9
ACCESSORIES
AC 102 Cover
AC 102 and AS 102 S cover
ERGO 802 Cover
ERGO 802 and AS 802 cover
10
POWER REQUIREMENT
100V; 120V; 230V; 240V 50/60Hz
(Voltage is factory preset according to region of sale).
Markaudio amps are manufactured to be sold and used in the country of purchase,
and are factory preset to that country’s voltage. Due to homologation issues, the
voltage may not be changed.
FUSE
EUROPE 4 A 250V T 5x20
AUSTRALIA/UK 4 A 250V T 5x20
USA/CANADA 8 A 250V T 5x20
JAPAN 10 A 250VT 5x20
/
