Master Lock DSKP0603PD User guide

Page is loading ...

Table of Contents

TABLE DE MATIÈRES ................................16

CONTENIDO

.......................................30

Features .............................................3

Operation

.........................................4 - 5

Changing the Batteries.................................6

Key Override .........................................6

NightWatch

®

Feature ..................................6

Programming

.....................................7 - 10

Security

............................................11

Troubleshooting

..................................13 - 14

Technical Assistance ..................................15

3ODFH/DEHO+HUH

Administrator Codes

1. 2.

3. 4.

2

Exterior

Interior









(QWHU



EXIT

PROGRAM

EXIT

MOTOR

EXIT

Keypad

Dial

“Enter” Button

Key Override

Battery Compartment

(uses 4 AAA batteries)

Program Button

Thumb Turn

NightWatch

®

Release

Exit Button

3

Operation

Using your new Electronic Deadbolt

couldn’t be easier!

To operate, simply follow these steps:

When the keypad is not illluminated

in green the dial free-spins and

doesn’t engage the bolt.

A. Press any button once to activate

the keypad.

B. Enter your 4–10 digit code and

press

Enter

(pre-set codes can be

found on pg. 2)

.

C. The keypad will light in green

when the correct code is entered.

D. Turn the dial to unlock or lock.

When the keypad is green, or ﬂashing green, the bolt can be

extended or retracted.

E. When leaving home, if the deadbolt is locked, simply turn

the deadbolt thumb-turn to unlock.

F. Press the

Exit

button. The keypad will be ﬂashing green.

G.

After closing the door behind you, turn the dial to re-lock the

deadbolt – you don’t have to enter your code. The exterior

dial will disengage after 15 seconds giving you ample time to

exit. You can also press any button to deactivate.

Note: To assure maximum security, always spin the dial to

ensure the mechanism has disengaged.

EXIT EXIT

Locked Unlocked

When the interior thumb turn

is horizontal, the lock is locked.

When it’s vertical, the

lock is unlocked.

4

EXIT









(QWHU



5









(QWHU











(QWHU













(QWHU











(QWHU











(QWHU













(QWHU



(QWHU









(QWHU













(QWHU

As an example, here are the steps for opening a lock with an

access code of ‘1958’:

Press any key

(keypad illuminates)

“5”

“1”

A, B

C

E

F

D, G

“8”

“9”

“Enter”

(keypad lights green;

turn dial to disengage

deadbolt)

Changing the Batteries

For low battery indications see

“Troubleshooting” on pages 13

and 14.

A. Remove interior cover.

B. Replace batteries with 4 AAA

alkaline batteries.

Key Override

You can use the key override

to open the lock if your

batteries are dead or user

code is unknown.

NightWatch

®

Feature

For added security you can

use the NightWatch

®

feature,

which locks out all keys

and codes. With the bolt

extended, push up on the

bottom release button and

pull out the thumb-turn to

activate NightWatch

®

.

PROGRAM

EXIT

MOTOR

EXIT

A

B









(QWHU



6

7

Programming

The deadbolt contains two factory-preset codes but can

be programmed to store up to a total of 20 additional

unique user codes. Codes can be added

and deleted at any time.

You’ll need to know your administrative code before

beginning programming. It can be found on the label

on the inside front cover of your user’s guide (page 2).

To begin programming:

Remove the upper interior cover (A).

Locate the “Program” button (B).

Programming an Entry Code

Press the “Program” button until the keypad on the exterior of the door

begins to ﬂash blue. When it ﬂashes blue you can release the button.

Enter your personal administrative code…

Push the

1-2

button (the function button for programming a

new code) and press

Enter

.

Type in a 4-10 digit code and again press

Enter

.

Re-enter your 4-10 digit code and again press

Enter

.

• If the keypad lights in green your new code has been conﬁrmed

and added.

• If it lights red the code wasn’t conﬁrmed and you’ll need to

repeat the steps again.

• If the keypad ﬂashes red, the code was found in the memory

and is already an active code.

PROGRAM

EXIT

MOTOR

EXIT

A

B

8

Deleting a Code

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Enter your personal administrative code…

Push the

3-4

button (the function button for deleting a code) and

press

Enter

.

Type in the 4-10 digit code you want to delete and again press

Enter

.

Re-enter the code and again press

Enter

.

• If the keypad lights in green the code was deleted.

• If it lights red the code wasn’t deleted and you’ll need to repeat the

steps again.

• If the keypad ﬂashes red, the code was not found in the memory

and is not an active code.

Changing the Administrative Code

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Enter your personal administrative code…

Push the

5-6

button (the function button for changing your

administrative code) and press

Enter

.

Type in your new 6-digit administrative code and press

Enter

.

Re-enter your new 6-digit administrative code and again press

Enter

.

• If the keypad lights in green your new administrative code has been

conﬁrmed and added.

• If it lights red the code wasn’t conﬁrmed and you’ll need to repeat

the steps again.

9

Deleting All Codes

If for any reason you want to remove all codes here’s how you do it.

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Enter your personal administrative code…

Push the

7-8

(the function button for deleting all codes) and

press

Enter

.

Re-enter your administrative code and again press

Enter

.

• If the keypad lights in green all codes have been deleted.

• If it lights red the deletions weren’t conﬁrmed and you’ll need

to repeat the steps again.

Deactivate / Reactivate All Codes

You can also deactivate all of your stored codes for a period of time

and then reactivate them.

<WLMIK\Q^I\MITTKWLM[°

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Enter your personal administrative code…

Push the

9-0

button (the function button for deactivating all

stored codes), and press

Enter

.

• If the keypad lights in green the deactivation has been

conﬁrmed.

•

If it lights red the codes weren’t deactivated and you’ll need to

repeat the steps again.

To reactivate the stored codes…

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Enter your personal administrative code…

Push the

9-0

button, the function activating all stored codes,

and press

Enter

.

If the keypad lights in green the reactivation has been conﬁrmed.

If it lights red the codes weren’t reactivated and you’ll need to

repeat the steps again.

Reset Factory-Set Administrative Code

You can easily reset the administrative code to the factory setting. If

you do this ALL user codes will be cleared.

Press the “Program” button until the keypad on the exterior of the

door begins to ﬂash blue. When it ﬂashes blue you can release the

button.

Press the “Program” and the “Exit” buttons (under battery holder)

together and hold them until the keypad turns solid blue – about

60 seconds.

At that point all user codes have been removed and the

administrative code has been reset to the factory set code. The

factory administrative code can be found on the label on the inside

front cover (pg. 2) of your User Guide.

10

11

Security

Use the chart below; keep track of your user codes. Do not share

your codes with anyone.

You can store up to 20 different user codes.

If you can’t remember who has a particular code you can delete all

of the stored codes (see Programming section).

As with any dial style lock, always spin the dial after locking and

LED turns off, to ensure the lock mechanism is disengaged (see

“Troubleshooting”).

Name / User Code

Page is loading ...

13

PROBLEM LIGHTS SOLUTION

FUNCTION:

Entry of User Code

does not engage dial

to throw or retract

bolt

Red 1. Ensure you are pushing a button to wake

up the keypad and then enter your code.

Red 2. Ensure that you are pressing hard enough

to activate each button as you enter your

user code. (Blue light gets brighter when

button registers a push).

Green 1. If lock has just been installed; the lock may

be binding and may need to be readjusted

by loosening the 2 long screws that secure

the Inside Assembly to the External

assembly, ensuring smooth bolt travel and

that no excess wires are interfering with

Sled travel (Sled is the black plastic part

below the cylinder tailpiece).

Green 2. If the lock has been installed and working

properly; typically retry and/or remove

the top battery for 10 seconds and then

reinstall it.

No Light Check batteries to make sure they are not

loose (also make sure they still have power) -

Check ribbon cable connection- you will need

to partially disassemble the lock to check the

ribbon cable connection.

There is a delay

before dial engages

bolt

Yellow

then

Green

Battery is low, replace soon.

Dial remains

engaged after green

LED turns off

None 1. Simply spin the dial, re-enter code and

dial should disengage when green light

turns off.

None 2. Remove top battery, wait 10 seconds and

reinstall battery. This is similar to rebooting

a computer.

3. Lock is malfunctioning. Log on to www.

masterdoorlock.com to access instructions

for emergency disabling of the dial.

NightWatch

®

feature

will not engage

None Ensure thumb turn is in the locked position,

release button is pushed in fully and thumb

turn shaft is installed properly (set screw hole

on bottom side when unlocked).

Troubleshooting

14

PROBLEM LIGHTS SOLUTION

NightWatch

®

won’t

engage – thumb-

turn can’t be pulled

out

None If thumb-turn cannot be pulled out it can be

due to insufﬁcient drill depth of the strike

hole. Try to engage NightWatch

®

with the

door open – if it works with the door open

the strike hole will have to be deepened.

User key or thumb

turn will not throw

or retract bolt

None Installation problem, cylinder tailpiece is

vertical instead of horizontal or vice versa.

PROGRAMMING:

Cannot add a new

user code

Red 1. User code entered differently 1

st

and 2

nd

time.

Red

Flashing

2. User code has already been assigned –

select a different user code that you have

not already programmed into the lock.

Note: Due to shared numbers on the buttons, the

code may be entered under different numbers. It

will still work for both numbers – test to conﬁrm.

Red 3. You’ve already entered the maximum

allowable(20 user codes) number of user

codes.

Cannot delete a user

code

Red User code entered differently 1

st

and 2

nd

time.

Red

Flashing

User code not found on the list.

Cannot change the

Administrator code

Red Administrator code entered differently 1

st

and

2

nd

time.

Cannot delete all

user codes

Red Administrator code entered differently 1

st

and

2

nd

time.

Cannot deactivate/

reactivate

Red Administrator code entered incorrectly.

Lock exits

programming mode

Red /

None

An incorrect entry was made during

programming (typically adding or omitting

the “Enter” button).

I forgot my

Administrator code

None Check programming guide for code.

I changed but did

not document my

administer code

None Reset to Factory-set Administrative Code

(see programming guide or log onto www.

masterdoorlock.com for online user guide).

Lock will not leave

programming mode

or any issue not

covered above

None /

Various

Remove top battery, wait 10 seconds and

reinstall battery. This is similar to rebooting

a computer.

15

Technical Assistance

For additional information or technical assistance, see

the installation and operation video at:

www.masterdoorlock.com

Model Number: DSKP

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

these instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encourage to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this product not expressly approved by the manufacturer could

void the user’s authority to operate the equipment.

Page is loading ...

109759

www.masterlock.com www.masterdoorlock.com

Master Lock Company LLC, Milwaukee, WI 53154 U.S.A. | 800-308-9244

Master Lock Canada, Oakville, Ontario L6H 5S7 Canada | 800-227-9599

Master Lock DSKP0603PD User guide

This manual is also suitable for

Master Lock DSKP0603PD User guide

in other languages

Related papers

Other documents