Belvedere BV403C Installation guide

Brand
Belvedere
Model
BV403C
Type
Installation guide
Belvedere USA Corporation
A Wholly Owned Subsidiary of Wella Corporation
One Belvedere Boulevard, Belvidere, Illinois 61008
Printed in U.S.A. 4000788 7-02 Rev. 8-04
Page 1 of 2
403 VACUUM BREAKER AND HOSE
RECEIVER INSTALLATION
403 VACUUM BREAKER
AND HOSE RECEIVER
Shampoo Fixtures
403 VACUUM BREAKER
VACUUM
BREAKER
R
IMPORTANT!
a)The device shall be installed in accordance with
the requirements of the local plumbing code.
b)The device shall not be installed where the
venting of water from the device during its
normal functioning causes damage.
c)The device shall be installed downstream of
the last valve.
1.Before installing your new Belvedere shampoo
bowl, we recommend that you first install the
plumbing fixtures to the bowl. Install fixtures
according to the instructions packed with them.
TO ATTACH THE HOSE RECEIVER TO
THE BOWL (STEPS 2 thru 6).
2.To make hose receiver installation easier,
complete these steps to cut screw threads
in the mounting holes:
S Take a mounting screw
and drive it 2 or 3
turns into one hole.
DO NOT OVERTIGHTEN.
S Remove the screw.
S Repeat for all four (4)
mounting holes.
3.Place the vacuum
breaker pipes
through the Gaskets
and the holes in the
hose receiver as
shown.
Secure the vacuum
breaker to the hose
receiver with
two hex-nuts.
DO NOT
OVERTIGHTEN.
SCREW
VACUUM
BREAKER
MOUNTING
HOLES
DRIVE
SCREW
IN 2 OR 3
TURNS
NOTE: Install the vacuum
breaker as shown.
The vacuum breaker will
interfere with the Spray
if it is installed backwards.
GASKETS
HOSE
RECEIVER
NUTS
VACUUM
BREAKER
GASKET
HOSE
RECEIVER
4. Place the gasket
over the flange
on the bottom
of the hose
receiver.
Page 2 of 2
REPLACEMENT PARTS
MOUNTING SCREW
DOME
5.Place the hose receiver in the bowl with the large
hole in the dome facing the front of the bowl.
Install the mounting bracket on the bottom side
of the bowl with four (4) embossed corners
facing upward, against the bottom of the bowl.
Secure with four (4) mounting screws.
DO NOT OVERTIGHTEN.
NOTE:On the following bowls, install the bracket
with the embossed corners facing down, away
from the bowl: 400, 4000, 8200, 8500, and 8501.
6.Connect the hoses. If your bowl is equipped with
the Model 622 fixture (with the teardrop handle),
use the pipe nipple provided to connect the
fixture hose to the fixture. Then attach the spray
hose connector to the vacuum breaker outlet.
If your bowl is equipped with the 522 Fixture (with
the loop handle), connect one end of the Fixture
Hose to the inlet side of the Vacuum Breaker.
Connect the other end to the fixture tailpiece.
Attach the Spray hose connector to the vacuum
breaker outlet.
5001816 1 Cap
2 Retainer
5001228 3 Seat Washer
4 Float
5001814 5 Gasket
1
2
3
4
5
BRACKET (EMBOSSED
CORNERS UP)
SPRAY
PIPE
NIPPLE
FIXTURE HOSE
HOSE
RECEIVER
SPRAY
TAILPIECE
FIXTURE HOSE
HOSE RECEIVER WITH
VACUUM BREAKER
403 Vacuum Breaker Bagged Assembly Number Description
OUTLET
INLET
Any conformance with LOCAL CODES or
INSPECTIONS is the RESPONSIBILITY OF
THE PURCHASER.
50018161 Cap2 Retainer50012283 Seat Washer4 Float5 Spring50018146 Gasket
  • Page 1 1
  • Page 2 2

Belvedere BV403C Installation guide

Brand
Belvedere
Model
BV403C
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents