Crosley BGGF3031KWD Installation guide

Brand: Crosley

Model: BGGF3031KWD

Type: Installation guide

GRLP3 CONVERSION KiT APPLiCATiON iNSTRUCTiONS

INSTALLATION AND SERVICE MUST BE PERFORMED BY

A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

I_ This conversion kit must be installed by a qualified service technician in accordance with the

manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction.

Failure to follow instructions may result in fire, explosion or production of carbon monoxide causing property

damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of

this kit. The installation is not proper and complete until the operation of the converted appliance is checked as

specified in the manufacturer's instructions supplied with this kit.

Before proceeding with the conversion, shut off the gas supply and disconnect the electrical

power to the range. Be sure both power supplies are off before installing the conversion kit. Failure to do so

could cause serious bodily injury.

IMPORTANT: Do not attempt to use this conVersion kit on products for which itis not specifically

designated: Consult the product installation manual or parts list to determine the correct conversion

kit number prior to use.

Tools Required for L.P. Conversion"

(A) 3/8", 1/2" and 5/8" Open End Wrench, (B) #1 Square Tip Screwdriver,

A--_ B--_

C-_ D-__

How to Convert the Range for use with LP/Propane Gas

1. Convert the Pressure Regulator

To access the gas regulator, remove the storage drawer or warmer drawer. If equipped with a storage drawer, open and remove the drawer completely. For

models equipped with a front panel, remove the front panel and skip steps b & c below. For models equipped with warmer drawer, follow all the instructions

below to remove the warmer drawer. NOTE: DO NOT ATTEMPT TO CONVERT MODELS THAT FEATURE A LOWER OVEN.

a. _ Electrical Shock Hazard can occur and result in serious injury or death. Disconnect electrical power to the range

before removing the warmer drawer for servicing.

b. Locate glide lever on each side of drawer, pull up on the left glide lever and push down on the right glide lever (See Fig. 1).

c. Pull the drawer away from the range (See Fig. 2).

........ _ ,:;:,2_ ................... _,_:: _ .........

Pull up with finger

Left Glide

Pushdown with finger

[]

Fig. 1

p/n 316417518 rev F (1008)

Fig. 2

( Continued on following page )

After removing the drawer identify which type of regulator is installed on the range by comparing to

the photos below. Follow the appropriate conversion instructions found on the following pages.

Hex Shaped Cap

Aluminum Top I

Fig. 3 Aluminum Regulator i

Plastic Dust Protector I

I Fig. 4 Steel Top Regulator I

iNSTRUCTiONS FOR CONVERTING ALUMINUM REGULATOR:

If the regulator has an aluminum top as pictured in Fig. 3 convert the regulator in the following manner:

A. Remove the regulator access cover if equipped. Do not remove the Pressure Regulator or allow it to turn.

B. Unscrew the hex shaped cap and turn it over to access the conversion plug inside the cap. (Fig A)

Do not remove the spring from the regulator.

C. Rotate the plug 90 degrees in either direction to align the tabs on the plug with the notches in the cap. (Fig. B)

Lift the plug out of the cap.

D. Turn the plug over so that the

nib on then end of the cap faces

out and re insert into the cap.

Rotate the plug 90 degrees in

either direction to lock it into the

cap (Fig C)

E. Reinstall the cap and plug

securely onto the regulator.

F. Attach the LP conversion label

as illustrated on page 8 then

complete the remaining steps in

the instructions provided with

the LP kit.

i CONVERSION PLUG [ TO UNLOCK J

REINSTALL PLUG

WITH NIB POINTING UP

INSTRUCTIONS FOR CONVERTING STEEL TOP REGULATOR: If the regulator has a steel top as pictured in Fig. 4 above

convert the regulator in the following manner:

A. Remove the regulator access cover if equipped. Do not remove the Pressure Regulator or allow it to turn.

B. Remove the plastic dust protector from the cap (Fig 5). Using a 5/8" wrench, unscrew the cap from the pressure regulator (Fig 6).

Do not remove the spring from the regulator.

C. Turn the cap over so the hollow end faces outward. Place the solid end of the cap into the loop end of the dust protector

(See Fig. 7).

D. Replace the cap on the regulator with the hollow end facing out (Fig 8). Do not over tighten the cap. Snap the dust protector over

the regulator cap.

E. Attach the LP conversion label as illustrated on page 8 then complete the remaining steps in the instructions provided with the LP

kit.

NOTE: The pressure regulator cap

may be made d brass or aluminum

depending on the age of the

product. The conversion process is

the same for both types of caps.

2.Convert Surface Burners for use with LP/Propane Gas

This conversion kit contains multiple gas orifices for converting different styles of sealed gas surface burners. Determine

which style of gas surface burner is being converted and select the proper orifice from the designated orifice pack for that

jspecific burner styJe and size.

lSave the natural gas orifices removed from the appliance for possible future conversions to natural gas.

BURNER STYLE #1 (Non Mounted Burner) NoMountingScrews J

This burner style is not secured to the cooktop with screws and the burner head

can be lifted off the cooktop to access the orifice holder and orifice. The orifice

holder for this style of burner passes through a circular cut out in the cooktop as '_

seen in the photo. I _ _+_This style of burner will use the orifices contained in the main envelope of the

converting this burner style.

BURNER STYLE #2 (Screw Mounted Burner)

This burner is secured to the cooktop surface by two screws as seen in the photo.

The screw heads may be different than those illustrated. When the burner is

removed the orifice holder cutout in the cooktop can be seen to have an irregular

elongated shape. The mounting screw sockets for the burner head are also

visible. This style of burner will use the orifices contained in the separate smaller

envelope found inside the main envelope of the LP kit # GRLP3. This envelope

will be labeled " SCREW MOUNTED BURNER LP KIT". Follow the instructions on

page 4 when converting this burner style.

BURNER STYLE #3 (Screw Mounted Burner)

This burner can be identified by the two piece cap as seen in the photo. It is

secured to the cooktop surface by two screws. The screw heads may be different

than those illustrated. When the burner is removed three orifice openings can

be seen in the cooktop. This style of burner will use the orifices contained in the

separate smaller envelope found inside the main envelope of the LP kit # GRLP3.

This envelope will be labeled " SCREW MOUNTED BURNER LP KIT". Follow the

instructions on page 5 when converting this burner style.

OVAL BURNERS

There are currently two different oval surface burners used and each one requires

a different LP orifice. Both burners are rated 9500 BTU and are very similar in

appearance when the burner caps are in place. Use the photos at right to identify

which oval burner is on your range and use the appropriate orifice for that burner

when converting.

Oval Burner A - Use orifice size .89 from the main envelope. The orifice holder

for this burner will have the circular cooktop opening as seen in Burner Style #1.

Oval Burner B - Use orifice size .93 from envelope labeled " SCREW MOUNTED

BURNER LP KIT". The orifice holder for this burner will have the elongated

cooktop opening as seen in Burner Style #2.

NOTE: Some ranges may include multiple burner styles. When this is

encountered use the appropriate orifice for each burner styJe and size.

BURNER STYLE #1

Burner Secured With Screws Elongated Cooktop Opening

BURNER STYLE #2

Burner Secured With Screws J

BURNER STYLE #3

Oval Burner B

Top View Bottom View

BURNER STYLE #1 CONVERSION INSTRUCTIONS

Use caution when replacing each burner cap

so the electrode is not damaged.

Example of Burner Assembly

letter

located f__

inside _._ ,

Burner _ J=l_:_;_ _,_._

Head _//_

B .....

Head i i_':g& _ :!i

theMatchletter

stamped ( t j) _r_ elect1\ ;ode

on Burner \ _> J

Skirt with _Bumer Skirt

Burner Head _ .........

and Burner Cap

B = 9.5k

D=12k

E = 14 or 14,2k

B = 9.5k

Top View Bottom View

Unlike the standard gas range,

THIS COOKTOP ISNOT REMOVABLE.

Do not attempt to remove this cooktop.

B = 9.5k

(some models)

A= 5k

B = 9.5k

_=.._Round Or Oval Center Burner --

B = 9.5k

D = 12k

E = 14 or 14.2k

F = 16 or 16.2

B _=&,Sk

( Continued on page 4 )

( Continued from page 3 )

Unlike the standard gas range

THIS COOKTOP IS NOT REMOVABLE.

Do not attempt

to remove this cooktop.

GAS SURFACE BURNER ORIFICE DATA CHART (Burner Style #1)

BTU Rating / Natural Gas 5,000 9,500 12,000 14,000 16,000

Natural Gas Orifice 1.01 1.54 1.75 1.93 1.99

LP Gas Orifice .68 .89 .95 1.01 1.15

LP Orifice Marking Color Blue None Green Red Black

BTU Rating / LP Gas 4,500 8,000 10,000 11,000 14,000

_*Note: For at elevations above 2000operation

ft.,

appliance rating

_shall be reduced at the rate of 4 percent for each 1000 ft. above sea

level.

For all burner locations:

a. Remove the top grates and burner caps (See Fig. 10).

b. Lift off the burner heads.

i Fig. 10

Burner

Head

Do Not _

R..... 7 Electrode Fig. 11

7mm

Nut

Driver

c. Remove the factory installed natural gas orifices one at a time from the center of the orifice holder using a 7 mm nutdriver (See Fig. 11).

Remember to keep the original Natural Gas Orifices for later conversion to Natural Gas.

d. Replace the orifice with the correct LP/Propane gas orifice (See the Surface Burner Orifice Data Chart ; also refer to Fig 9 for the

correct LP orifice installation at each of the surface burner locations). Tighten each orifice until snug. Use caution not to overtighten.

Repeat for each surface burner.

e. Replace the burner heads. Match letter located under center of Burner Caps with letter located inside Burner Heads. Match the letter

stamped on Burner Skirt with Burner Head and Burner Cap. (Refer to Fig. 9). Be sure burner heads mate correctly with each surface

igniter, then replace the burner caps and burner grates.

Unlike the standard

gas range,

THIS COOKTOP IS

NOT REMOVABLE.

BURNER STYLE #2 CONVERSION INSTRUCTIONS

Use caution when replacing each burner cap so the electrode is not damaged.

Do not attempt

to remove this

cooktop. Fig. 12

For all burner locations:

a. Remove Burner Grates & Burner Caps.

Mounting screws

7ram Nut Driver

oril

Fig. 13

Ignitor Alignment

Fig. 14

b. If the opening in the burner is too small to allow removal of the orifice, remove the burner as follows: Remove 2 screws using #1 square tip driver and

remove Burner Heads (Figs 12 ). NOTE - Some models may have 3/16" hex head screws instead of square drive screws.

c. Remove the factory installed natural gas orifices from the center of the orifice holders using a 7 mm nutdriver (See Fig. 13). Save the natural gas

orifices removed from the appliance for possible future conversion back to natural gas.

d. Following the chart below select the appropriate LP/Propane gas orifice from the envelope labeled SCREW MOUNTED BURNER LP KIT.

EXAMPLE: Natural Gas orifcie marked 1.07 is replaced by LP orfice marked .66. Tighten all orifices until snug. Use CAUTION not to overtighten.

e. Replace burner heads at all locations and tighten each position with original screws using #1 square tip driver. Make sure that the center of the ignitor

aligns with the center nib in the burner head (Figs. 14). Heads MUST have a Burner Cap installed to insure proper ignition and gas flame size.

GAS SURFACE BURNER ORIFICE DATA CHART (Burner Style #2)

BTU Rating / Natural Gas 5,000 9,500/10,000 12,000 14,000 15,000 16,000 17,000 18,000

Natural Gas Orifice 1.07 1.46 1.67 1.87 1.95 1.98 2.1 2.2

L P Gas Orifice 0.66 0.93 1.02 1.09 1.09 1.18 1.18 1.18

LP Orifice Marking Color Pink White Yellow Brown Brown Silver Silver Silver

BTU Rating / LP Gas 5,000 9,500 12,000 14,000 14,000 16,000 16,000 16,000

*Note: For operation at elevations

above 2000 ft., appliance rating

shall be reduced at the rate of 4

percent for each 1000 ft. above

sea level.

BURNER STYLE #3 (TWIN BURNER) CONVERSION INSTRUCTIONS

Two Piece Burner Cap I Remove Burner Mounting Screws

Unlike the standard gas range, THIS COOKTOP IS NOT REMOVABLE.

Do not attempt to remove this cooktop.

For all burner locations:

a. Remove burner grates &lift off thetwo piece burner cap. (Fig. 15)

Fig. 17

! Simmer Orifice

_win Orifices !

_Orifice Openings ]

b. Remove the two burner mounting screws using the appropriate screwdriver or nutdriver and remove burner head (Figs 16). NOTE - Burners may be

secured with 3/16" hex head screws or square drive screws,

c. Remove the factory installed natural gas orifices from the orifice holders using a 7 mm nutdriver (See Fig 17). Save the natural gas orifices

removed from the appliance for possible future conversion back to natural gas.

d. Replace the orifice in each of the orifice holders with the appropriate LP/Propane gas orifice from the envelope labeled SCREW MOUNTED

BURNER LP KIT. Note that there are two identical orifices for the main portion of the burner and a separate smaller orifice for the center/simmer

portion of the burner. Tighten all orifices until snug. Use CAUTION not to overtighten.

e. Replace burners at all locations and tighten each position with original screws. Burners MUST have a Burner Cap installed to insure proper ignition

and gas flame size.

GAS SURFACE BURNER ORIFICE DATA CHART (Burner Style #3)

SIMMER TWIN (Main)

BTU Rating / Natural Gas 750 17,000

Natural Gas Orifice 0.43 1.46 (Qty 2)

L P Gas Orifice 0.22 0.84 (Qty 2)

LP Orifice Marking Color Orange Purple

BTU Rating / LP Gas 750 15,000

*Note: For operation at elevations

above 2000 ft., appliance rating shall

be reduced at the rate of 4 percent for

each 1000 ft. above sea level.

BURNER STYLE #3 (TWIN BURNER) CONTROL VALVE ADJUSTMENT

Adjust the "LOW" Setting of the Twin Burner Surface Valve Fig. t8

(Figure 18) (some models):

Note: On the Twin burner surface valve the low setting of each portion

(inner portion and outer portion of the twin burner) should be adjusted

individually. _'_

a. Push in and turn control to ignite the burner ,_

b. Quickly turn knob to LOWEST POSITION.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. The inner portion of the twin burner flame size can be increased or

decreased with the turn of the screwA. Use screw B to adjust the

flame size of the outer portion of the twin burner. Turn

counterclockwise the screw to increase flame size. Turn clockwise the

screw to decrease flame size. Adjust flame until you can quickly turn

knob from LITE to LOWEST POSITION without extinguishing the

flame. Flame should be as small as possible without going out.

Note: Air mixture adjustment is not required on surface burners.

3. Convert Oven Burner Orifice I

Fig. t9

for LP/Propane Gas (16,000 BTU*)

a. Locate the oven burner spud (See Fig. 18).

b. Using a 1/2" wrench, turn down the adjustable spud, which injects gas

into the oven burner, until snug against the LP/Propane metering pin

(approximately 2-1/2 turns). Do not over tighten.

4. Convert Waist=High Broiler Burner Orifice

Flame for LP/Propane Gas (13,500 BTU*)

( Some Models )

a. Open the oven door.

b. Locate the broiler burner spud and turn down until snug against the LP/

Propane metering pin (approximately 1to 1-1/2 turns). Do not over tighten

(See Fig. 18).

I*Note: For operation at elevations above 2000 ft,, appliance rating shallbe reduced at the rate of 4 percent for each 1000 ft. above sea level,

Oven Burner

Orifice

5. Reconnect Gas and Electrical Supply to Range.

Leak testing of the appliance shall be conducted according to the Installation Instructions provided with the Range.

Do not use a flame to check for gas leaks.

Checking Manifold Gas Pressure

If it should be necessary to check the manifold gas pressure, remove the burner cap and connect a manometer (water gauge) or other pressure device

to the top right front burner orifice. Using a rubber hose with inside diameter of approximately 1/4/' hold tubing down tight over orifice. Turn burner valve

on. For an accurate pressure check, have at least two (2) other surface burners burning. Be sure the gas supply (inlet) pressure is at least one inch above

specified range manifold pressure. The gas supply pressure should never be over 14" water column. When properly adjusted the manifold water column

pressure is 10" for LP/Propane gas or 4" for Natural gas.

Pressure Testing Gas Supply Piping System

a. Disconnect the range and its individual shut-off valve from the gas supply piping system during any pressure testing of that system at test pressures

greater than 14" of water column pressure (approximately 1/2" psig).

b. Isolate the range from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping

system at test pressures equal to or less than 14" of water column pressure (approximately 1/2" psig).

6. Test surface burners to verify if "LOW" setting

should be adjusted"

a. Push in and turn control to LITE until burner ignites.

b. Push in and quickly turn knob to LOWEST POSITION.

c. if burner goes out, reset control to OFR

d. Remove the surface burner control knob.

e. insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted

screw inside. Flame size can be increased or decreased with the turn of the screw.

Turn counterclockwise to increase flame size. Turn clockwise to decrease flame size.

(See Figs. 19 & 20).

Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without

extinguishing the flame. Flame should be as small as possible without going out.

NOTE: For Twin Burner Valve Adjustments follow the instructions on page 5.

Surface

Burner

Fig: 20

Burner Flame Size

Main

Top

Fig: 21

7. Air Shutter=Oven Burner

The air shutter for the oven burner may need adjustment, especially if the unit has been

converted for use with LP/Propane gas. The approximate flame length of the oven burner

is 1 inch (distinct inner, blue flame) (See Fig. 21).

To determine if the oven burner flame is proper:

a. To access the air shutter you must remove the storage drawer or warmer drawer

(see removal instructions on page 2).

b. Remove the oven bottom by removing the screws at rear of oven bottom. Lift up

the rear of oven bottom and slide toward back of range to disengage from front of

oven front frame.

c. Remove burner baffle by removing nut located on top of baffle and two screws from

front edge of oven front frame. Lift baffle straight up and out of the oven.

d. Set the oven to bake at 350°F and observe the flame. If the flame is yellow in color,

increase air shutter opening size. if the flame isa distinct blue color, but lifting away

from the burner; reduce the air shutter opening size.

1" Flame

Fig. 22

( Continued on following page )

Burner Oven

Z Burner

Tube

"'J Waist-High BUI Lock Screw

Locking iLower (Self Clean Mo( AirShutter

; Orifice

Screw Ov_enBaffle _;4_mAir Shutter i Hood

Air Shutter --:::-"

Fig. 25

Orifice Hood i i -Lower Oven Bottom

(Spud) _ _ Air Shutter (Removable)

Fig. 23

Fig. 24

e. Turn off oven and allow to cool before adjusting air shutter. To adjust, loosen lock-screw (3), reposition air shutter (2), and tighten lock-screw (3)

(See Fig. 22). Retest the burner by repeating step "d" above. When the burner flame is a distinct blue color burning steady, the air shutter is

adjusted correctly.

f. Replace burner baffle and oven bottom.

8. Air Shutter=Broil Burner

a. Observe the flame to determine ifthe broiler burner flame is properly adjusted, it should be steady with approximately 1" blue cones and no yellow or

orange flame tips (See Fig. 23).

b. if adjustment to the air shutter is necessary, locate the broiler burner air shutter (See Fig. 24), loosen shutter lock screw, and adjust to obtain optimum

flame. This will normally be completely open for LP/Propane gas. if the flame is yellow in color, increase the air shutter opening size. if the flame isa

distinct blue, but lifting away from the burner, reduce the air shutter opening size. Tighten the shutter set screw.

9. Replace Storage Drawer or Warmer Drawer _._

(instructions for warmer drawer if equipped): I Fig.26 I

a. Pull the bearing glides to the front of the chassis glide (See Fig. 25). _,,,,,_-,--,_ ?_ "_\-_

b. Align the glide on each side of the drawer with the glide slots on the range.

c. Push the drawer into the range until levers "click" (approximately 2"). Pull the drawer open again to

seat bearing glides into position. If you do not hear the levers "click" or the bearing glides do

oo,,o.,.oa,o0.o ovo,,o0 a o ao0a

damage to the bearing glides.

10. installation of New LP/Propane Rating/Serial Plate Remove Storage Drawer (somemodels),

and Conversion Label Panel or Warmer Drawer (if equipped)

for access to Regulator

a. Using the list on page 8, determine the Surface Burner Combination that applies

to the range after it has been converted and select the corresponding Rating Plate

part number in the approprate language (English/French). Serial

b. Use a pen or permanent marker to fill out the LP/Propane Rating/Serial plate. Plate

include the date that the LP conversion was performed and the service company

or individual performing the conversion. See the sample label below

c. Place new plate as close as possible to the existing Rating/Serial plate on range

(See the recommended locations shown in Fig. 26). _

e. Remove the lower storage or warmer drawer and install the Regulator L.P.

Conversion Label in the location shown in figure 26. Fig. 27 Pressure Regulator

location at rear of ranc

Sample - L.P, Rating/Serial Plate

: E:_E::,T::L CE.ROOR,_.TEUR.

THIS CONTROL _ _U HU _eT_ CONVERT!

HAS BEEN CONVERTED HA S|DO CONVERTIDO POUR ETRE UT L S_

FOR USE WITH PARA USARSE . ........

p/n 316241200 (0811)

Sample - Regulator L.P. Conversion Label

CONVERSION TO NATURAL GAS

if it becomes necessary to convert the range back to natural gas:

a. Disconnect gas and electrical supply from range.

b. Convert pressure regulator (See step 1), turn cap over so the solid end of cap faces outward. Place the hollow end of the cap into the loop end of the

dust protector.

c. Remove the LP orifices using 7ram nutdriver and replace with the original factory installed natural gas orifices at their original locations (See figure 9

for locations).

d. Convert Oven Burner Orifice for Natural Gas by loosening spud counter-clockwise (approximately 2-1/2 turns; See step 3).

e. Convert Waist-High Broiler Burner Orifice (Self-Cleaning Models Only) for Natural Gas by loosening spud counter-clockwise (approximately 1 to 1-1/2

turns; See step 4.)

f. Readjust "LOW" Setting for Surface Burner Valves following instructions. (See step 6.)

g. Readjust Oven & Broil Burner Air Shutters. (See steps 7 & 8.)

:)TY

Pa_ Number

316037528

316417518

316241200

316237910

316237904

316237905

316237906

316237907

316255600

316527507

316527512

316527503

316527501

316527505

316527515

316527516

GRLP3 CONVERSION KIT - CONTENTS

Notes

Item Description

LP Conversion Kit Label

Instructions, Kit, GRLP3

LP Conversion Label - Regulator

Orifice 14,000 Btu/h size 1.15

Orifice 11,000 Btu/h size 1.01

Orifice 10,000 Btu/h size .95

Orifice 8,000 Btu/h size .89

Orifice 4,500 Btu/h size .68

Label, Insert Kit Screw Down Burner

For Non Mounted Burner (Style 1)

For Non Mounted Burner (Style 1)or Oval BumerA

For Non Mounted Burner (Style 1)

Orifice 16,000 Btu/h size 1.18

Orifice 14,000 Btu/h size 1.09

Orifice 12,000 Btu/h size 1.02

Orifice 9,500 Btu/h size .93

Orifice 5,000 Btu/h size .66

Orifice 15,000 Btu/h size .84

Orifice 750 Btu/h size .22

For Screw Mounted Burner (Style 2)

For Screw Mounted Burner (Style 2) or Oval Burner B

For Screw Mounted Burner (Style 2)

For Screw Mounted Burner (Style 3)

Qty

Pa_

Number

316005215

316005216

316005217

316005218

316005219

316005220

316005221

316005222

316005223

316005224

316005225

316005226

316005227

316005228

316005229

316005230

316005233

316005234

316005235

316005236

316005237

316005238

316005239

316005240

316005241

316005242

316005243

316005244

Description

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Surface Burner Combination

4-8k

3-8k, 1-10k

2-8k, 1-10k, 1-4.5k

1-8k, 1-10k, 1-4.5k, 1-11k

4-8k

Qty

Pa_

Number

316005245

316005246

316005247

316005248

316005249

Description

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Surface Burner Combination

3-9.5k, 1-12k

3-9.5k, 1-14k

2-9.5k, 1-12k, 1-5k

3-8k, 1-10k

2-8k, 1-10k, 1-4.5k

1-8k, 1-10k, 1-4.5k, 1-11k

2-8k, 1-11k, 1-4.5k

3-8k, 1-11k

1-8k, 1-10k, 1-4.5k, 1-14k

2-8k, 1-10k, 1-4.5k, 1-14k

1 316005250

1 316005251

1 316005252

1 316005253

1 316005254

1 316005255

1 316005256

1 316005257

1 316005258

1 316005259

1 316005260

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

2-9.5k, 1-12k, 1-5k

2-9.5k, 1-5k, 1-14k

1-9.5k, 1-12k, 1-5k, 1-16k

2-9.5k, 1-12k, 1-5k, 1-16k

4-9.5k, 1-5k

1-9.5k, 1-8k, 1-12k, 1-5k, 1-16k

4-9.5k

4-8k, 1-4.5k

3-8k, 1-4.5k, 1-11k

5-8k

4-8k, 1-10k

2-8k, 1-10k, 1-4.5k, 1-11k

1 316005261

1 316005262

1 316005263

1 316005264

1 316005265

1 316005266

1 316005267

1 316005268

1 316005269

1 316005270

1 316005271

1 316005272

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

4-9.5k, 1-8k

3-9.5k, 1-8k, 1-12k

1-9.5k, 1-12k, 1-5k, 1-14k

2-9.5k, 1-14k, 1-5k, 1-8k

1-9.5k, 1-14k, 1-12k, 1-5k

1-15k, 1-14k, 1-8k, 1-9.5k, 1-5k

1 316005277

1 316005278

1 316005279

1 316005280

1 316005281

1 316005282

1 316005283

1 316005284

1 316005285

1 316005286

1 316005287

1 316005288

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

Rating Plate - French

Rating Plate - English

1-16k, 1-14k, 2-9.5k. 1-5k

5-9.5k

3-9k, 1-5k, 1-12k

1-14k, 2-9k, 1-5k, 1-15k

Crosley BGGF3031KWD Installation guide

Crosley BGGF3031KWD Installation guide

Crosley BGGF3031KWD Installation guide

Related papers

Other documents