EZ-FLO 10707 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
10705
10707
Tools and Supplies
You will need the following to install your new faucet:
Groove
Joint Pliers
Pipe
Tape
Adjustable
Wrench
Phillips
Screwdriver
Single Control
Tub & Shower Trim Kit
Before You Begin
Check to make sure you have the following:
• For use with an automatic compensating valve
rate at 1.45 gpm (5.5 L/min) or less.
• This product is engineered to meet the EPA
WaterSense flow requirement. The flow rate is
governed by the flow controller. If replacement is
ever required, be sure to replace it with a
WaterSense compliant flow controller to retain
the water conserving flow rate of this product.
Shut off main water supply before installation.
Faucet Installation
1 Shut off water supply. 2 Install shower flange and
shower arm.
3 Install showerhead
and tighten with
wrench.
4 Install nipple for spout. The
distance from the valve to the
tub spout stub out should be
between 8" (20 cm) and 18" (45
cm).
5A Installation on 1/2" Copper Pipe
(5/8" OD):
Slip on installation over 1/2" copper pipe:
Back out set screw in bottom of spout to
allow spout to slide on stub out pipe.
Slide the flange and spout over the pipe
with the spout tight to the wall, tighten
the set screw to the pipe.
5B Threaded installation with 1/2" Steel or
Brass Pipe(7/8" OD):
Apply pipe sealant tape on the pipe nipple
threads. Before installing spout, remove the
adapter assembly (including plastic
adapter, plastic washer, O-Ring) by backing
out the set screw and pulling out the copper
tube adapter assembly. Slide the flange and
spout over the pipe; with the spout tight to
the wall, tighten the set screw to the pipe.
6 Before installing
escutcheon, remove the plastic
cap from plaster guard by
twisting cap to the clockwise.
7 Install escutcheon and sleeve onto
valve.
8 Screw in handle.
8"~18"
203mm~457mm
Ø 5/8"
(Ø 15.9mm)
1 3/8"~2"
(35mm~51mm)
1/2"-14NPT
1 5/8"~1 11/16"
(41mm~43mm)
1 Shower Head S1213402
2 Shower Arm A020002
3 Shower Arm Flange A019001-S
4 Metal Handle Assembly A66E895
5 Screw Set A608563
6 Escutcheon Assembly A667A12
7 Sleeve A103322
8 Spout Escutcheon A303028
9 Spout w/Diverter A666226
10 Hex Wrench (H3.18 *20 mm L * 90 mm L) A031017NI
Troubleshooting Guide
Problem Cause Solution
Keep this manual for ordering replacement parts.
Replacement Parts
Leaks underneath handle. Cartridge has come loose or o-ring
on cartridge is dirty or twisted.
Tighten the cartridge by turning it clockwise. Move the
cartridge stem to the “on” position. If either o-ring is
twisted, straighten it out. If either o-ring is damaged,
replace it.
Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and
close stopper or drain to avoid losing small parts.
3.
2.
1.
4.
5.
6.
7.
8.
10.
9.
-
1
-
2
-
3
EZ-FLO 10707 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI