Eurotech DynaDOT 10-13 Owner's manual

Original User Manual

DynaDOT 10-13

Ultra Thin, Fanless Dot Matrix Information Panel

Rev. 1-0 — 21 September 2016 — DYDOT-10-13_UserMan_EN_1-0 — ENGLISH

Trademarks

All trademarks and registered trademarks are the property of their respective owners.

Revision history

Revision Description Date

1-0 First release 21 September 2016

DynaDOT 10-13 User Manual Rev 1-0 Table of contents

TABLE OF CONTENTS

Trademarks 2

Revision history 2

Table of contents 3

1 Important Information 5

1.1 Signals used in this document 5

1.2 Disclaimer of liability 6

1.3 Intended audience 6

2 Safety Instructions 7

2.1 Observe antistatic precautions 7

2.2 Connect the power supply correctly 7

3 How to receive technical assistance 9

3.1 How to receive technical support 9

3.2 How to return a product to Eurotech 9

4 Conventions used in this document 11

4.1 Conventions for signal names 11

4.2 Abbreviations for direction and electrical characteristics of a signal 11

5 Product overview 13

6 Declaration of Conformity 15

6.1 CE Marking 15

6.2 RoHS compliance 15

6.3 WEEE compliance 15

7 Technical Specifications 17

8 Product interfaces 19

8.1 Interfaces overview 19

8.2 Ethernet connectors ETH1 and ETH2 20

8.2.1 Connector pinout 20

8.2.2 Connector specifications 20

8.2.3 Mating connector specifications 20

8.3 Power connector 21

8.3.1 Connector pinout 21

8.3.2 Connector specifications 21

8.3.3 Mating connector specifications 21

8.4 Protective earthing terminal 21

9 Install the product 23

9.1 Observe the following installing precautions 23

9.2 Unpack the product 23

9.3 Observe antistatic precautions 23

9.4 Installing procedure 24

10 Mechanical specifications 27

11 Maintain the product 29

11.1 Use antistatic precautions 29

11.2 Remove the power supply 29

11.3 Inspect the installation of the product 29

3 / 32

Table of contents DynaDOT 10-13 User Manual Rev 1-0

11.4 Clean the front panel (the display) 29

11.5 Clean the chassis 30

Notes 31

4 / 32

DynaDOT 10-13 User Manual Rev 1-0 1 Important Information

1 IMPORTANT INFORMATION

CAREFULLY READ AND UNDERSTAND THE INSTRUCTIONS CONTAINED IN THIS

DOCUMENT BEFORE INSTALLING / OPERATING THE PRODUCT.

KEEP THIS DOCUMENT FOR FUTURE REFERENCE.

Whenever you have any doubt regarding the correct understanding of the instructions contained in this

document contact your local Eurotech Technical Support Team (see the last page of this document for

further details).

To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the following

precautions, as well as using good technical judgment, whenever installing / operating the product.

1.1 Signals used in this document

DANGER

INDICATES A HAZARD WITH A HIGH LEVEL OF RISK WHICH, IF NOT AVOIDED, WILL

RESULT IN DEATH OR SERIOUS INJURY

WARNING

INDICATES A HAZARD WITH A MEDIUM LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD

RESULT IN DEATH OR SERIOUS INJURY

CAUTION

INDICATES A HAZARD WITH A LOW LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD

RESULT IN MINOR OR MODERATE INJURY

NOTICE

Indicates practices not related to personal injury, such as:

l An instruction to follow to use the product effectively

l A statement of company policy related to product or property protection

5 / 32

1 Important Information DynaDOT 10-13 User Manual Rev 1-0

1.2 Disclaimer of liability

Eurotech has reviewed the contents of this document to ensure accuracy and consistency with the

hardware and software described.

Always refer to the latest available manual revision available at: www.eurotech.com.

1.3 Intended audience

This document is intended for system integrators, who are skilled persons with a thorough knowledge in

bringing together component subsystems into a whole, ensuring that those subsystems function together.

6 / 32

DynaDOT 10-13 User Manual Rev 1-0 2 Safety Instructions

2 SAFETY INSTRUCTIONS

Observe the following safety instructions when installing / operating the product.

Failure to comply with these instructions or with specific warnings elsewhere in this document violates

safety standards of design, manufacture, and intended use of the product.

Eurotech assumes no liability for any failure to comply with these instructions.

2.1 Observe antistatic precautions

NOTICE

PREVENTING ELECTROSTATIC DISCHARGE (ESD)

When handing the product described in this document, always use appropriate

antistatic precautions to avoid damages due to electrostatic discharge.

For example: use a wrist strap or ESD cuff kept in constant contact with bare skin

and attached to an ESD ground.

2.2 Connect the power supply correctly

WARNING

ELECTRIC SHOCK HAZARD

Before applying power, thoroughly review all installation, operation, and safety instructions.

Failure supply power correctly or to follow all operating instructions correctly, may create an

electric shock hazard, which could result in personal injury or loss of life, and / or damage to

equipment or other property.

To avoid injuries:

l Before operating any equipment, carefully read any supplied instructions

l Do not perform any connections with wet hands

l Check any power cords for damage before using them

l Use certified power cables. The power cables must meet the power requirements of the

device

l Position cables with care. Avoid positioning cables in places where they may be

trampled or compressed by objects placed on them

l Take particular care of plugs, power-points and outlets. Avoid overcharging them

l Always disconnect power and discharge the circuits before touching them

l Only start the product with a power supply that meets the requirements stated on the

voltage label. In case of uncertainties about the required power supply, contact the

Eurotech Technical Support Team (see the back cover for full contact details) or the

electricity authority.

7 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 3 How to receive technical assistance

3 HOW TO RECEIVE TECHNICAL ASSISTANCE

3.1 How to receive technical support

If you have technical questions, or if you cannot isolate a problem with your product, or for any inquiry

about repair and returns policies, contact:

l The Eurotech Global Support Center: support.eurotech.com/

l Your local Eurotech Technical Support Team: see the back cover for full contact details.

3.2 How to return a product to Eurotech

To return a product to Eurotech, complete the following steps:

1. Send an email to the Eurotech RMA Department (rma.it@eurotech.com) specifying:

l Product Model Number (printed on the product label)

l Product Serial Number (printed on the product label)

l Recap of the fault description

2. Receive a reply from the Eurotech RMA Department. It contains:

l The RMA number

l The shipping information

3. Pack the product using anti-static material and place it in a sturdy box with enough packing material

to adequately cushion it

4. Ship the product to Eurotech following the information received from the Eurotech RMA

Department.

NOTICE

Any product returned to Eurotech that is found to be damaged due to inappropriate packaging

will not be covered by the warranty!

When shipping the product:

1. Pack it using anti-static material

2. Place it in a sturdy box with enough packing material to adequately cushion it.

9 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 4 Conventions used in this document

4 CONVENTIONS USED IN THIS DOCUMENT

4.1 Conventions for signal names

Convention Description

GND Digital ground plane

# Active low signal

_P Positive signal in differential pair

_N Negative signal in differential pair

4.2 Abbreviations for direction and electrical characteristics of

a signal

Convention Description

I Signal is an input to the system

O Signal is an output from the system

IO Signal may be input or output

P Power and ground

A Analog signal

3.3 3.3 V signal level

5 5 V signal level

NC No Connection

Reserved Use is reserved to Eurotech

11 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 5 Product overview

5 PRODUCT OVERVIEW

The DynaDOT 10-13 is an EN50155 certified, fanless dot matrix display certified for Railway applications

that delivers high brightness, high efficiency LEDs in a very thin enclosure.

Figure 5.1 - DynaDOT 10-13 front view

Figure 5.2 - DynaDOT 10-13 rear view

13 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 6 Declaration of Conformity

6 DECLARATION OF CONFORMITY

6.1 CE Marking

This product is CE marked.

The product meets the guidelines listed in the following sections.

Eurotech is not responsible for the use of this product together with equipment (e.g. power

supplies, personal computers, etc.) that are not CE marked and compliant with the

requirements specified in this document.

6.2 RoHS compliance

The product described in this document, including all its components and its sub-assemblies, have been

manufactured in compliance with the Directive 2011/65/EU of the European Parliament and of the Council

of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic

equipment.

6.3 WEEE compliance

In compliance with the Directive 2012/19/EU of the European Parliament and of the Council

of 4 July 2012 on waste electrical and electronic equipment (WEEE), the symbol on the

right, shown on the product or within its literature, indicates separate collection for this

electrical and electronic equipment (EEE) that has been placed on the market after 2005.

This product, at the end of its life cycle, must be collected separately and managed in

accordance with the provisions of the current Directive on waste electrical and electronic

equipment.

Because of the substances present in the product, improper use or disposal of the refuse

can cause damage to human health and the environment.

To avoid any possible legal implications, contact your local waste collection body for full

recycling information.

15 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 7 Technical Specifications

7 TECHNICAL SPECIFICATIONS

Specifications Description

Dynamic area resolution 58 x 18 dots

Dot pitch 4 mm

Active area 232 x 72 mm

Brightness >2000 cd/m²

Viewing angle ± 30°

LED color Yellow (590 nm) - Other colors available upon request

Interfaces l Fast Ethernet

l Internal switch for daisy chaining

l Ethernet bypass mode

Power supply Nominal: 110 VDC; Range: 77 to 137.5 VDC

Power consumption 15 W typical

Temperature Operating: EN50155 Class T3 (-25 to +70°C; +85°C for 10 minutes)

Storage: -30 to +85°C

Humidity < 95% at 45°C non-condensing

Dimensions 280 x 180 x 35 mm (W x H x D)

Weight 3 kg

Chassis Aluminum - black anodized

IP rating IP54

Compliance l CE

l EN 50155 (Railway applications)

l EN 61373 (Vibrations & Shocks)

l EN 50121 (Surges, Electrostatic discharge, Burst, radio

frequency, Interference susceptibility and radio frequency

disturbances, Emission test)

l EN 60068 (Temperature test)

l UNI CEI 11170 (Fire & Smoke)

17 / 32

(This page has been intentionally left blank)

DynaDOT 10-13 User Manual Rev 1-0 8 Product interfaces

8 PRODUCT INTERFACES

8.1 Interfaces overview

This section gives you an overview of the interfaces available on the DynaDOT 10-13.

Ref# Description

1 Ethernet connector ETH1

2 Ethernet connector ETH2

3 Luminosity sensor

4 Power connector

5 Protective earthing terminal. M6 screw hole.

This protective earthing terminal must be connected to

an earth point in the installation. The connection to earth

of this terminal is mandatory.

19 / 32

8 Product interfaces DynaDOT 10-13 User Manual Rev 1-0

8.2 Ethernet connectors ETH1 and ETH2

8.2.1 Connector pinout

Pin# Name Type Description

1 TX+ O Transmit Data +

2 RX+ I Receive Data +

3 TX- O Transmit Data -

4 RX- I Receive Data -

8.2.2 Connector specifications

Type Female, circular, panel-mount

4-pin, M 12, D Code

8.2.3 Mating connector specifications

Type Male, circular

4-pin, M 12, D Code

(Example: Lumberg 0986EMC105 or equivalent)

20 / 32

Page is loading ...

Eurotech DynaDOT 10-13 Owner's manual

Eurotech DynaDOT 10-13 Owner's manual

Related papers

Other documents