Wacker Neuson PSA21503L User manual

Operator’s Manual

Pump

PS2-1503L / 2203L

PSA2-1503L / 2203L

Type PS2-1503L / 2203L, PSA2-1503L / 2203L

Document 5000184994

Date

1215

Version 04

Language

EN

5000184994

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

Foreword

wc_tx001295gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered by

this manual

Machine

documentation

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson Corporation reserves the right

to change any portion of this information without notice.

Machine Item Number Machine Item Number

PS2 1503L 0620461

0620462

PSA2 1503L 0620463

PS2 2203L 0620464

0620465

PSA2 2203L 0620466

Foreword

4 wc_tx001295gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2015-CE-PS2-xxxx_en_FM10_new.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

PST2 400, PS2 500, PSA2 500, PS2 800, PSA2 800, PS2 1503, PS2 1500,

PS2 1503L, PSA2 1503L, PS2 2203, PS2 2203L, PSA2 2203L, PS2 3703

Water Pump Units

To pump fluid

5000009173, 5000009175, 5000008786, 5000008788, 5000008789,

5000008793, 5000008794, 5000008796, 5000009176, 5000009178,

5000008787, 5000008790, 5000008792, 5000009179, 5000009181,

5000620438, 5000620439, 5000620452, 5000620449, 5000620450,

5000620458, 5000009186, 5000008802, 5000008803, 5000009190,

5000009190, 5000008814, 5000008815, 5000008826, 5000008827,

5000620461, 5000620462, 5000620463, 5000620464, 5000620465,

5000620466

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2006/95/EC, 2004/108/EC, EN 809, EN ISO 12100, EN 60204-1,

EN 60335-1, EN 60335-2-41, EN 62233, EN 61000-6

Authorized Person for Technical Documents

Leo Goeschka, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,

80809 München

Menomonee Falls, WI, USA, 27.04.15

Original Declaration of Conformity

Dan Domanski

Technical Director

For Wacker Neuson

Travis Pound

Manager, Product Engineering

For Wacker Neuson

Keith Herr

Managing Director

For Wacker Neuson

wc_bo5000184994_03TOC.fm 7

Table of ContentsPS2/PSA2 1503L/2203L

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating and Electrical Safety .......................................................... 11

1.4 Labels ................................................................................................. 12

2 Operation 13

2.1 Names of Parts ................................................................................... 13

2.2 Prior to Operation ............................................................................... 14

2.3 Preparing for Installation .................................................................... 14

2.4 Preparing for installation ..................................................................... 15

2.5 Installation .......................................................................................... 16

2.6 Checks to Make Before Installation .................................................... 17

2.7 Electrical Wiring .................................................................................. 18

2.8 Cable Assembly ................................................................................. 19

2.9 Electrical Circuit Diagram ................................................................... 20

2.10 Operation ............................................................................................ 21

2.11 Operating Water Level ....................................................................... 22

2.12 Starting Water Level (PSA2 models) .................................................. 23

2.13 Circle Thermal Protector .................................................................... 26

2.14 Emergency Shutdown Procedure ....................................................... 26

3 Maintenance 28

3.1 Periodic Maintenance Table ............................................................... 28

3.2 Maintenance and Inspection .............................................................. 29

3.3 Storage ............................................................................................... 29

3.4 Lubrication Inspection and Changing Procedures .............................. 30

3.5 Replacement Parts ............................................................................. 31

3.6 Disassembly/Reassembly .................................................................. 31

3.7 Disassembly ....................................................................................... 32

3.8 Reassembly ........................................................................................ 33

3.9 Troubleshooting .................................................................................. 34

8 wc_bo5000184994_03TOC.fm

Table of Contents PS2/PSA2 1503L/2203L

4 Technical Data 35

4.1 Standard Specifications .......................................................................35

4.2 Operating Specifications .....................................................................36

4.3 Dimensions .........................................................................................37

5 AEM Safety Manual 38

wc_si000366gb.fm

9

PS2/PSA2 1503L/2203L Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000366gb.fm

10

Safety Information PS2/PSA2 1503L/2203L

1.2 Machine Description and Intended Use

This machine is a submersible water pump. The Wacker Neuson Submersible Pump

consists of an electric motor, an impeller, a strainer, and a metal casing with ports for

water suction and discharge. Power is supplied to the pump through a corded plug or a

hard-wired connection, depending on the installation. The operator connects hoses to

the pump and routes them so that water is pumped from the work area and discharged

into an appropriate location.

This machine is intended to be used for general de-watering applications. This machine

is intended for the pumping of clear water, or water containing solids up to the size

stated within the product’s specifications, and up to the flow, head, and suction lift limits

also stated within the product’s specifications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine damage

caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Pumping flammable, explosive, or corrosive fluids

 Pumping hot or volatile fluids that result in pump cavitation

 Operating the pump outside of product specifications due to incorrect diameter

hoses, incorrect length hoses, other inlet or outlet restrictions, or excessive

suction lift or head

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest global safety

standards. It has been carefully engineered to eliminate hazards as far as practicable

and to increase operator safety through protective guards and labeling. However, some

risks may remain even after protective measures have been taken. They are called

residual risks. On this machine, they may include exposure to:

 Electric shock from improper electrical connections or high voltage

 Personal injury from improper lifting techniques

 Projectile hazard from discharge

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000366gb.fm

11

PS2/PSA2 1503L/2203L Safety Information

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

1.3 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded, grounding-

type receptacle.

Risk of electric shock—this pump has not been investigated for use in swimming

pool areas.

An acceptable motor-control switch shall be provided at the time of installation

according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for proper

installation.

CAUTION: This pump may automatically restart. Prior to working on the pump or

control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

WARNING

wc_si000366gb.fm

12

Safety Information PS2/PSA2 1503L/2203L

1.4 Labels

Wacker Neuson machines use international pictorial labels where needed. These

labels are described below.

A nameplate listing the model number, item number, revi-

sion number, and serial number is attached to each unit.

Please record the information found on this nameplate so it

will be available should the nameplate become lost or dam-

aged. When ordering parts or requesting service informa-

tion, you will always be asked to specify the model number,

item number, revision number, and serial number of the

unit.

CAUTION

Do not attempt to operate this product before reading the

Operator’s Manual and understanding its contents. Mishan-

dling of this product may result in explosion, fire, or electri-

cal shock.

 Do not pull on the power cord or use the power cord to lift

the pump.

 Always use a dedicated ground leakage circuit breaker.

 Be sure to install the ground wire securely.

 Be sure to disconnect the power supply before handling

or inspecting the pump.

Never insert your hand into the pump inlet holes while the

pump is connected to the power supply.

JAPAN

wc_tx001296gb.fm

13

PS2/PSA2 1503L/2203L Operation

2 Operation

2.1 Names of Parts

1

14

13

5

12

11

10

4

7

6

9

15

wc_

g

r01049

9

Ref Description Ref Description

1 Lifting handle 9 Lubricant

2 Coupling 10 Seal-dust (V-ring)

3 Protective packing 11 Shaft sleeve

4 Oil plug 12 Rear liner

5 Pump casing 13 Oil casing

6 Strainer stand 14 Impeller

7 Cable assembly 15 Electrode (if equipped)

8 Seal-mechanical — —

wc_tx001296gb.fm

14

Operation PS2/PSA2 1503L/2203L

2.2 Prior to Operation

When the pump is delivered, first perform the following checks:

 Inspection

While unpacking, inspect the product for damage during shipment, and make sure

all bolts and nuts are tightened properly.

 Specification check

Check the model number to make sure it is the product that was ordered. Be

certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your nearest

dealer or Wacker Neuson representative at once.

 Product specifications

Do not operate this product under any conditions other than those for which it is

specified. Failure to observe this precaution can lead to electrical shock, current

leakage, fire, water leakage, or other problems.

2.3 Preparing for Installation

Preparing for

Installation

Observe the following points when preparing to install the pump.

 Be aware that leakage of pump lubricants may cause pollution of water.

 An appropriate plug or electrical connection must be provided according to local

codes and standards. Refer to the wiring diagram.

 Use with a power supply voltage within ±5% of the rated voltage.

Operating

Safety

 Do not operate the pump if the maximum water pressure in the area exceeds

0.3 MPa–discharge pressure.

 Do not use this pump in liquids other than water, such as oil, salt water, or

organic solvents. Contact your Wacker Neuson dealer with questions about

specific fluids.

 Do not use in water temperatures outside the range of 0–40°C (32–104°F)

which can lead to failure, electrical leakage, or shock.

 Do not use in the vicinity of explosive or flammable materials.

 Do not operate the pump if any parts are loose or missing.

CAUTION

wc_tx001296gb.fm

15

PS2/PSA2 1503L/2203L Operation

2.4 Preparing for installation

Before installing the pump at a work site, you will need to have the following tools

and instruments ready:

 Insulation resistance tester (megohmmeter)

 AC voltmeter

 AC ammeter (clamp-on type)

 Bolt and nut tighteners

 Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test instruments.

Measure

resistance

Use a megohmmeter to measure the insulation resistance between each core lead

and the ground lead to verify the insulation resistance of the motor.

 Reference insulation resistance: 20MΩ or greater

Note: The reference insulation resistance (20M

Ω

or greater) is the value when the

pump is new or has been repaired. For the reference value after installation, see

“Periodic Maintenance Table.”

wc_gr007262

Description Description

U Power Lead (Brown) W Power Lead (Black)

V Power Lead (Blue or Gray) G Ground (Green/Yellow)

wc_tx001296gb.fm

16

Operation PS2/PSA2 1503L/2203L

2.5 Installation

If the pump is used for outdoor fountains, garden ponds and similar places, or to

drain a swimming pool, the pump must be supplied by an isolating transformer or

connected to a Residual Current Device (RCD) with a residual operating current

not exceeding 30 mA.

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards. Refer to

wiring diagram.

Do not use this pump in liquids other than water, such as oil, salt water, or organic

solvents.

Use with a power supply voltage within ±5% of the rated voltage.

Do not use in water temperatures outside the range of 0–40°C

(32–104°F) which can lead to failure, electrical leakage or shock.

Do not use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker Neuson representative before using

with any liquids other than those indicated in this manual.

WARNING

wc_tx001296gb.fm

17

PS2/PSA2 1503L/2203L Operation

2.6 Checks to Make Before Installation

 When a grounded plug is used:

Use the megohmmeter to measure the insulation resistance between the cable

assembly prongs and ground.

 When connection leads are used:

With the megohmmeter, measure the insulation resistance between each core lead

and the ground lead.

Reference insulation resistance: 20MΩ or greater

Note: The reference insulation resistance (20M

Ω

or greater) is the value when the

pump is new or has been repaired. For the reference value after installation, see

“Periodic Maintenance Table.”

Improper ways to measure insulation resistance

All models 1 Between the plug prongs.

PSA2 1503L

PSA2 2203L

2 Between the electrode and the pump body.

3 Between the electrode and each lead wire.

1

wc_gr007330

2

3

wc_tx001296gb.fm

18

Operation PS2/PSA2 1503L/2203L

2.7 Electrical Wiring

General

information

 Electrical wiring should be performed by a qualified electrician in accord with all

applicable regulations. Failure to observe this precaution not only risks breaking

the law, but is extremely hazardous.

 Make sure the pump is equipped with the specified overload protectors, fuses,

and/or breakers. These items are designed to guard against electrical shock

from a current leak or pump malfunction.

 Operate within the capacity of the power supply and wiring.

Grounding the

pump

 Do not use the pump without first grounding it properly.

 Do not attach the grounding wire to a gas pipe, water pipe, lightning rod, or

telephone grounding wire.

Connecting

the power

supply

 Before connecting leads to the terminal strip, make certain the power supply is

disconnected (i.e. through circuit breakers) to avoid electrical shock, shorting, or

unexpected starting of the pump.

 Do not use the pump with the cable assembly connected loosely.

 Draw power from a dedicated power outlet rated at 15 A or above. Sharing the

outlet with other equipment may cause overheating at the branch outlet and

could result in fire.

 Use a dedicated power supply with a ground leakage circuit breaker.

 Tighten the ends of the cable assembly securely against the terminal board.

WARNING

An improperly wired pump can result in current leakage, personal injury, electrical

shock, fire, or permanent equipment damage.

f Observe the safety considerations below when performing electrical wiring.

wc_gr007264

Description Description

U Power Lead (Brown) W Power Lead (Black)

V

Power Lead (Blue or Gray)

G Ground (Green/Yellow)

wc_tx001296gb.fm

19

PS2/PSA2 1503L/2203L Operation

2.8 Cable Assembly

Extending the

cable

If it is necessary to extend the cable assembly, use a core size equal to or larger

than the original. This is necessary to avoid a performance drop and cable

overheating which may result in current leakage, electrical shock, or fire.

Avoiding

cable damage

 Do not suspend the pump by the cable.

 Make sure the cable does not become excessively bent or twisted.

 Do not allow the cable to rub against a structure in a way that might damage it.

 Repair or replace a cut or damaged cable immediately.

Submerging

the cable

 Do not submerge a cable with cut insulation or other damage.

 If it is necessary to submerge the connection wires of the cable assembly in

water, first seal the wires completely in a molded protective sleeve.

 Do not allow the cable assembly wires or power supply plug to become wet.

WARNING

Current leakage, electrical shock, or fire hazards.

f Observe the safety considerations below when handling the cable assembly.

wc_tx001296gb.fm

20

Operation PS2/PSA2 1503L/2203L

2.9 Electrical Circuit Diagram

If connected to a circuit protected by a fuse, use a time-delay fuse with this pump.

wc_gr007099

1

2

3

Br

L-Gr

B

G/Y

Ref. Description Ref. Description

1 Circle thermal protector 3 Ground

2Coil ——

Wire Colors

B Black V Violet Or Orange

G Green W White Pr Purple

L Blue Y Yellow Sh Shield

P Pink Br Brown LL Light Blue

R Red Cl Clear G/Y Green/Yellow

T Tan Gr Gray L-Gr Blue or Gray

CAUTION

Page is loading ...

Wacker Neuson PSA21503L User manual

This manual is also suitable for

Wacker Neuson PSA21503L User manual

Related papers

Other documents