Livex Lighting 42658-91 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
42658-91
Category
Motorcycle Accessories
Type
Operating instructions

This manual is also suitable for

Livex Lighting 42658-91 is a versatile lighting fixture that can elevate the ambiance of any room. With its adjustable cord length, you can customize the hanging height to suit your needs, ensuring optimal illumination. The fixture's sturdy mounting plate and secure locking mechanisms guarantee stability and safety. The multiple lamp holders allow for the use of various light bulbs, giving you the flexibility to create the desired lighting effect. Whether you seek bright illumination or a cozy atmosphere, this fixture seamlessly adapts to your preferences.

Livex Lighting 42658-91 is a versatile lighting fixture that can elevate the ambiance of any room. With its adjustable cord length, you can customize the hanging height to suit your needs, ensuring optimal illumination. The fixture's sturdy mounting plate and secure locking mechanisms guarantee stability and safety. The multiple lamp holders allow for the use of various light bulbs, giving you the flexibility to create the desired lighting effect. Whether you seek bright illumination or a cozy atmosphere, this fixture seamlessly adapts to your preferences.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
42657 42658
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and all
hardware from Junction Box. Carefully unpack your new fixture and lay out all
the parts on a clear area. Take care not to lose any small parts necessary for
installation.
2. By measuring, determine correct distance hole in mounting plate, then drilled
three holes(by measuring distance hole) in the ceiling at junction box of side;
raise the plastic anchor insert the hole. Attach the mounting plate to the
junction box with two junction box screws and three wood screws as shown,
tighten screws securely with the screwdriver. The side of the mounting plate
marked "GND" must face out. The junction box is not included.
3. By measuring, determine correct cord length of needed for proper hanging
height, then lock it securely with small screw. NOTE: SLIDE WIRE CLIP TO
THE PROPER POSITION, THEN YOU MAY PROPERLY CUT THE CORD IS
TOO LONG PARTS. CONNECT THE ELECTRICAL WIRES AS SHOWN IN
FIG.2.
4. While holding the lamp body towards the ceiling, connect the electrical wires
as Shown in Fig.2, making sure that all wire nuts are secured. You may have
to wrap the connections with electrical tape. If your outlet has a ground wire
(green or bare copper), connect the fixture ground wire to it. Otherwise
connect fixture’s ground wire directly to the Mounting strap with the green
screw provided. After wires are connected, tuck them carefully inside the
Junction Box.
5. Raise the lamp body(A) onto the junction box, aligning the pipe thread on
mounting plate with mounting hole in canopy and lock it securely with the
round nut(B).
6. Raise the outside lamp holder into the top ring of the shade(E, 6pcs), lock it
securely with the check ring until tight.
7. Install the light bulbs(Not included) in accordance with the fixture’s
specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAG!
8. Raise the center lamp holder frame insert the shade (C,1pc), aligning the end
bracket hole of the top shade with the top screw hole of the lamp holder frame,
lock it securely with the screws until tight. Using the same method install the
middle lamp holder frame and shade(D,3pcs).
Your installation is now complete. Return power to the junction box
the fixture.
BoxScrew
WoodScrew
NO Lettering
HOUSE
Black
WIRES
(Hot)
FIXTURE
WIRES
Lettering
WIRES
FIXTURE
Bare
FIXTURE
WIRES
(Ground)
HOUSE
(Neutral)
WIRES
White
Green or
WIRES
HOUSE
Copper(Ground)
Yellow
Thread
( L )
( N )
( )
Or Black
Or White
Fig.2
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us on-line at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20161242657
FIG.1
  • Page 1 1

Livex Lighting 42658-91 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
42658-91
Category
Motorcycle Accessories
Type
Operating instructions
This manual is also suitable for

Livex Lighting 42658-91 is a versatile lighting fixture that can elevate the ambiance of any room. With its adjustable cord length, you can customize the hanging height to suit your needs, ensuring optimal illumination. The fixture's sturdy mounting plate and secure locking mechanisms guarantee stability and safety. The multiple lamp holders allow for the use of various light bulbs, giving you the flexibility to create the desired lighting effect. Whether you seek bright illumination or a cozy atmosphere, this fixture seamlessly adapts to your preferences.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents