2. Flash Furniture
  3. Black Fabric Kneeling Posture Task Chair

Flash Furniture Black Fabric Kneeling Posture Task Chair Owner's manual

  • Hello! I've reviewed the assembly instructions for the Belnick Posture Task Chair WL-1430-GG. This document provides a step-by-step guide on how to assemble your new chair. It also includes important safety information and warranty details. I am ready to assist you with any questions you may have about the assembly process or the chair itself.
  • What should I do before starting assembly?
    What is the warranty for non-moving metal parts?
    What is the weight limit for using this chair?
WL-1430-GG
Thank you for your purchase !
ASSEMBLY INSTRUCTIONS
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
- Small Parts. Adult Assembly Required.
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: CustomerExperience@belnick.com | Phone: 866-552-2810
Mobile Ergonomic Kneeling
Posture Task Chair
with Back
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/WL-1430-GG.pdf
Have a Que on/Concern?
Quality products and rst-class customer service are the cornerstone of long-
consumer hips. We strive toward excellence in all we do and
want you to be completely s d with your purchase.
Please contact our excep onal Customer Experience Agents at the email
address or phone number shown below to assist you with any product
ques ons or issues before reques ng a return.
We look forward to serving you in a friendly, e cient manner to resolve any
issues you may have.
Customer Service Email: CustomerExperience@belnick.com
Customer Service Phone: 866-552-2810
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal
usage, according to the below-referenced speci ca ns and limita ons.
Non-moving metal parts are warranted for 5 years.
Component parts including pneuma c cylinder, control mechanism, base and casters
are warranted for 2 years.
All other items are warranted for 1 year.
Normal usage means use in compliance with the rest ns and weight limits speci ed for
the product. In the absence of product-speci c rest ns and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by
pes other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
altera on, assembly, installa on, a achments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scu ng, or blemishing of
leather or fabric; (3) cosme c damage that may result from normal usage; (4) damage
a butable to use by persons exceeding speci d weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resul g from use of this product. Liability for
incidental or consequen al damage is excluded. Some states do not allow the exclusion or
limita on of incidental or consequen al damages, so the above limita on or exclusion may
not apply to you.
PARTS LISTING
STEP 1 STEP 2 STEP 3
5PCS
A
1PC
B
2PCS
E F
1PC
G
6PCS4PCS
C D
2PCS
4PCS 1PC
A
B
N
F
-2
-2
-1
-3
-1
-3
K L M N
Casters Cylinder Cylinder CoverSpacer Ø19mm
Small Washer
HØ38mm
Large Washer
Small Screw
M8x55mm
Large Screw
5-Star BaseBack Assembly
Back Assembly
Insert Casters (Part A) into the 5
Star Base(Part N). Insert large end of
Cylinder (Part B) into the base then slide
Cylinder Cover (Part F) over the column.
Insert Back Assembly (Part K) into the
Kneeler Assembly (Part J). Insert Hitch
Pin (Part -2) through mounting holes
and secure with R-Clip (Part -2) see
diagram.
Insert Tensioner Bolt ( Part -1) throught
complete set of Tension Spring and Knob
(Part -3).
Cylinder Cover
Cylinder
Casters
5-Star Base
KBack Assembly
K
J
R-Clip
Hitch
Pin
Kneeler Assembly
JKneeler Assembly Seat Cushion Kneeler Cushion
1PC 1PC 1PC1PC 1PC
Cylinder Receptacle
J Kneeler Assembly
STEP 4 STEP 5
STEP 6
G
D
H
E
H
G
C
During assembly, hand tighten screws only. When all screws are in place,
you may then tighten all screws completely.
1.Do not use this chair as a step ladder.
Attach Kneeler Assembly (Part J) to Seat Cushion (Part L) using
(4) Ø19mm Small Washers (Part G) and (4) mm Small
Screws (Part C)
Attach Kneeler Cushion (Part M) to Kneeler Assembly (Part J)
using (4) Ø38mm Large Washers (Part H), (2) Spacers (Part
E), (2) Ø19mm Small Washers (Part G) and (2) M8x55mm
Large Screws(Part D).
Return assembled chair to the upright position. Insert top of
Cylinder into Cylinder Receptacle on the underside of the seat
(See Step 3) and push down.
Ø19mm Small Washer
Seat Cushion
L
Kneeler Cushion
M
Spacer
Ø19mm Small Washer
Ø38mm Large Washer
Ø38mm Large Washer
M8x55mm Large Screw
J
Kneeler Assembly
J
Kneeler Assembly
/