Note
Before using this information and the product it supports, be sure to read the
general information under Appendix, “Notices” on page A-1.
Fourth Edition (August 1998)
The following paragraph does not apply to the United Kingdom or any country where such
provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES
CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
states do not allow disclaimer of express or implied warranties in certain transactions, therefore,
this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be incorporated in new editions of
the publication. IBM may make improvements and/or changes in the products and/or programs
described in this publication at any time.
It is possible that this publication may contain reference to, or information about, IBM products
(machines and programs), programming, or services that are not announced in your country. Such
references or information must not be construed to mean that IBM intends to announce such IBM
products, programming, or services in your country.
Requests for technical information about IBM products should be made to your IBM Authorized
Dealer or your IBM Marketing Representative.
A form for readers’ comments appears at the back of this publication. If the form has been
removed, address your comments to:
Department CGFA
Design & Information Development
IBM Corporation
PO Box 12195
RESEARCH TRIANGLE PARK NC 27709-9990
USA
When you send information to IBM, you grant IBM a nonexclusive right to use or distribute the
information in any way it believes appropriate without incurring any obligation to you.
Copyright International Business Machines Corporation 1995, 1998. All rights
reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use,
duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule
Contract with IBM Corp.
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . v
About This Manual .......................... xi
How This Manual Is Organized .................... xi
| Summary of Change .......................... xii
Chapter 1. Introducing the Adapters .............. 1-1
Adapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Using the Wake on LAN Feature .................. 1-3
About the Adapter Fault Tolerance Feature ............ 1-3
About DHCP/RPL Support with the Adapters ........... 1-4
Prerequisite Operating System PCI Updates ........... 1-4
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Adapter Installation Checklist .................... 1-5
Help Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Chapter 2. Installing the Adapter Hardware ......... 2-1
Installing the Adapter ........................ 2-1
Using the Correct Adapter Cable .................. 2-3
Connecting Your Wake on LAN Cables .............. 2-4
Chapter 3. Dynamic Host Configuration Protocol and
Remote Program Load ...................... 3-1
About the Flash Module ....................... 3-1
Installing the Flash Module ..................... 3-1
Programming the Flash Module .................. 3-4
RPL Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
RPL Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
DHCP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Chapter 4. Testing Your Adapters and Installing Device
Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Using the Help Files on the Diagnostics and Help Diskette .. 4-1
Common Problems and Solutions ................. 4-2
Related Technical Topics ...................... 4-4
Appendix. Notices . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Copyright IBM Corp. 1995, 1998 iii
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Electronic Emission Notices ..................... A-2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-1
iv 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Safety Information
Danger: Before you begin to install this product, read the
safety information in
Caution: Safety Information—Read This First
,
SD21-0030. This booklet describes safe procedures for cabling and
plugging in electrical equipment.
Gevaar: Voordat u begint met de installatie van dit produkt,
moet u eerst de veiligheidsinstructies lezen in de brochure
PAS OP!
Veiligheidsinstructies—Lees dit eerst,
SD21-0030. Hierin wordt
beschreven hoe u electrische apparatuur op een veilige manier moet
bekabelen en aansluiten.
Danger: Avant de procéder à l'installation de ce produit, lisez
d'abord les consignes de sécurité dans la brochure
ATTENTION:
Consignes de sécurité—A lire au préalable,
SD21-0030. Cette
brochure décrit les procédures pour câbler et connecter les appareils
électriques en toute sécurité.
Perigo: Antes de começar a instalar este produto, leia as
informações de segurança contidas em
Cuidado: Informações Sobre
Segurança—Leia Isto Primeiro,
SD21-0030. Esse folheto descreve
procedimentos de segurança para a instalação de cabos e conexões
em equipamentos elétricos.
Contents v
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Fare! Før du installerer dette produkt, skal du læse
sikkerhedsforskrifterne i
NB: Sikkerhedsforskrifter—Læs dette først
SD21-0030. Vejledningen beskriver den fremgangsmåde, du skal
bruge ved tilslutning af kabler og udstyr.
Gevaar Voordat u begint met het installeren van dit produkt,
dient u eerst de veiligheidsrichtlijnen te lezen die zijn vermeld in de
publikatie
Caution: Safety Information - Read This First
, SD21-0030.
In dit boekje vindt u veilige procedures voor het aansluiten van
elektrische appratuur.
VAARA: Ennen kuin aloitat tämän tuotteen asennuksen, lue
julkaisussa
Varoitus: Turvaohjeet—Lue tämä ensin
, SD21-0030,
olevat turvaohjeet. Tässä kirjasessa on ohjeet siitä, miten
sähkölaitteet kaapeloidaan ja kytketään turvallisesti.
vi 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Danger : Avant d'installer le présent produit, consultez le livret
Attention : Informations pour la sécurité — Lisez-moi d'abord
,
SD21-0030, qui décrit les procédures à respecter pour effectuer les
opérations de câblage et brancher les équipements électriques en
toute sécurité.
Vorsicht: Bevor mit der Installation des Produktes begonnen
wird, die Sicherheitshinweise in
Achtung:
Sicherheitsinformationen—Bitte zuerst lesen,
IBM Form SD21-0030.
Diese Veröffentlichung beschreibt die Sicherheitsvorkehrungen für
das Verkabeln und Anschließen elektrischer Geräte.
Vigyázat: Mielôtt megkezdi a berendezés üzembe helyezését,
olvassa el a
Caution: Safety Information— Read This First,
SD21-0030 könyvecskében leírt biztonsági információkat. Ez a
könyv leírja, milyen biztonsági intézkedéseket kell megtenni az
elektromos berendezés huzalozásakor illetve csatlakoztatásakor.
Pericolo: prima di iniziare l'installazione di questo prodotto,
leggere le informazioni relative alla sicurezza riportate nell'opuscolo
Attenzione: Informazioni di sicurezza — Prime informazioni da
leggere
in cui sono descritte le procedure per il cablaggio ed il
collegamento di apparecchiature elettriche.
Contents vii
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Fare: Før du begynner å installere dette produktet, må du
lese sikkerhetsinformasjonen i
Advarsel: Sikkerhetsinformasjon —
Les dette først
, SD21-0030 som beskriver sikkerhetsrutinene for
kabling og tilkobling av elektrisk utstyr.
viii 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Perigo: Antes de iniciar a instalação deste produto, leia as
informações de segurança
Cuidado: Informações de Segurança —
Leia Primeiro
, SD21-0030. Este documento descreve como
efectuar, de um modo seguro, as ligações eléctricas dos
equipamentos.
Contents ix
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Peligro: Antes de empezar a instalar este producto, lea la
información de seguridad en
Atención: Información de Seguridad —
Lea Esto Primero,
SD21-0030. Este documento describe los
procedimientos de seguridad para cablear y enchufar equipos
eléctricos.
Varning — livsfara: Innan du börjar installera den här
produkten bör du läsa säkerhetsinformationen i dokumentet
Varning:
Säkerhetsföreskrifter— Läs detta först,
SD21-0030. Där beskrivs hur
du på ett säkert sätt ansluter elektrisk utrustning.
x10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
About This Manual
This manual contains instructions for installing and setting up the
device drivers for the following adapters:
¹IBM 10/100 EtherJet PCI Adapter
¹IBM 10/100 EtherJet PCI Adapter with Wake on LAN
Included is a product overview and a description of some of the
common installation problems and recommended solutions.
Note: The illustrations in this publication might be slightly different
from your hardware.
This manual is intended for adapter installers and network
administrators.
How This Manual Is Organized
This manual contains the following chapters and appendixes:
|¹Chapter 1, “Introducing the Adapters” describes the adapter kit
| contents, the Wake on LAN feature, the Adapter Fault Tolerance
| Feature, the DHCP/RPL option, the installation checklist, and
| help sources are included.
¹Chapter 2, “Installing the Adapter Hardware” provides
instructions for removing the cover and cables for your PC and
for locating the required components. Safety precautions and
handling techniques are discussed, along with the required
procedures for installing the adapters.
¹Chapter 3, “Dynamic Host Configuration Protocol and Remote
Program Load” provides information for installing and
programming the Remote Program Load and Dynamic Host
Configuration Protocol (DHCP/RPL) option on the 10/100
EtherJet PCI Adapters.
¹Chapter 4, “Testing Your Adapters and Installing Device Drivers”
provides information about how to use the help files on the
Diagnostics and Help Diskette to test your adapters and install
your device drivers.
Copyright IBM Corp. 1995, 1998 xi
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Note: You can access the Diagnostics and Help Diskette to
obtain instructions for loading the device drivers from the Device
Driver Diskette. See “Help Files” on page 1-6 for more
information.
A description of common problems and recommended solutions,
PCI installation tips, and related technical topics are included.
¹Appendix, “Notices” contains IBM notices and trademark
information.
|Summary of Change
| Support for Windows 98 has been added to this edition.
xii 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Chapter 1. Introducing the Adapters
This manual contains the information you need to install and use the
following products:
¹IBM 10/100 EtherJet PCI Adapter
¹IBM 10/100 EtherJet PCI Adapter with Wake on LAN
This chapter describes the adapters, the contents of the adapter kits,
and other materials you need to install these adapters. Topics
include:
¹“Adapter Overview”
¹“Using the Wake on LAN Feature” on page 1-3
|¹“About the Adapter Fault Tolerance Feature” on page 1-3
¹“About DHCP/RPL Support with the Adapters” on page 1-4
¹“Prerequisite Operating System PCI Updates” on page 1-4
¹“Kit Contents” on page 1-5
¹“Adapter Installation Checklist” on page 1-5
¹“Help Information” on page 1-6
* DHCP support means Pre-Execute Environment (PXE) remote boot
with Intel's LANDesk Service Agent (LSA) code in Dynamic Host
Configuration Protocol (DHCP).
It is important that you are familiar with the PC in which either of the
adapters will be installed and with the PC’s operating system and
network software.
These adapters use the same drivers and software utility. Therefore,
most of the information in this manual applies to both adapters
interchangeably. Where the information differs, it is noted.
Adapter Overview
The IBM 10/100 EtherJet PCI Adapters pave the way to higher
bandwidth operation and improved network performance, without
disrupting your existing infrastructure. It is easy to use these Plug
and Play, 32-bit Busmaster adapters. Designed for flexibility, they
run at 10 Mbps or 100 Mbps in full- or half-duplex mode to support a
Copyright IBM Corp. 1995, 1998 1-1
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
variety of network configurations, ranging from conventional
10BASE-T to Fast Ethernet environments.
The adapters:
¹Operate in shared 10BASE-T or 100BASE-TX environments as
well as in switched 10 Mbps and 100 Mbps Ethernet networks
¹Run at either 10 Mbps or 100 Mbps in full-duplex mode, yielding
20-Mbps and 200-Mbps capacity, respectively
¹Attach to 10-Mbps and 100-Mbps LANs with a single RJ-45
connector
¹Operate in symmetrical multiprocessing (SMP) environments
¹Display the status of link, activity, and 100-Mbps operation via
LEDs
|¹Support Novell NetWare 3.12 or higher, IBM OS/2 LAN Server,
| Microsoft LAN Manager, Windows for Workgroups 3.11,
| Windows NT 3.51 or higher, Windows 95, Windows 98, SCO
| Open Desktop 3.0, SCO Open Server 5.0, and SCO UnixWare
| 2.1 or higher.
|¹The 10/100 EtherJet PCI Adapter with Wake on LAN supports
| system wakeup events in both ACPI and APM environments with
| IBM Wake on LAN-capable PC systems.
¹The Boot ROM module is a standard feature for the 10/100
EtherJet PCI Adapter with Wake on LAN. The card comes with
an onboard ROM pre-flashed with Intel LANDesk Service Agent
code (LSA code) for Dynamic Host Configuration Protocol
(DHCP) remote boot ready. For the Remote Program Load
(RPL) remote boot, a flash utility disk is available for re-flashing
the ROM to RPL code.
¹For 10/100 EtherJet PCI Adapter, an optional ROM Module kit
(PN 86H2856) is available for your DHCP or RPL remote boot
applications.
1-2 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Using the Wake on LAN Feature
The Wake on LAN feature can be disabled or enabled using your
system configuration utility. Refer to your PC documentation for
details.
Power for the 10/100 EtherJet PCI Adapter with Wake on LAN is
always ON when the PC is connected to ac power, regardless of the
PC ON/OFF switch. When the PC power is OFF, this adapter
constantly monitors the LAN for the wake-up frame that requests
power to be applied to the PC.
The wake-up frame can be a broadcast or an individually addressed
frame. The following data is required and can occur anywhere in the
data portion of the wake-up frame.
¹6 bytes of X'FF', followed by
¹48-bit universally administered address (UAA or MAC address) of
the adapter to be woken up, repeated eight or more times. Eight
repetitions are required; more than eight are acceptable.
If you are not familiar with Wake on LAN operation, you can refer to
the following World Wide Web based documents:
¹
Wake on LAN
at http://www.pc.ibm.com/infobrf/iblan.html
¹
Wake up to Wake on LAN
at
http://www.networking.ibm.com/eji/ejiwake.html
| For more details about Wake on LAN cables and IBM Wake on LAN
| PC systems, read WOLCABLE.TXT and WOL-INFO.TXT help files in
| the \INFO\GENERAL directory on the Installation diskette.
About the Adapter Fault Tolerance Feature
Adapter Fault Tolerance (AFT), also known as redundant NIC, is a
simple, effective, and fail-safe approach to increase the reliability of
server connections. AFT gives you the ability to set up link recovery
to the server adapter in case of a cable, port, or network interface
card failure. By assigning two IBM 10/100 EtherJet PCI Adapters as
a team, AFT enables you to maintain uninterrupted network
Chapter 1. Introducing the Adapters 1-3
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
performance. For further AFT details, read the AFT.TXT help file in
the A:\INFO\GENERAL directory of the Diagnostics and Help
diskette.
About DHCP/RPL Support with the Adapters
With the onboard ROM on the 10/100 EtherJet PCI Adapter with
Wake on LAN, or the optional ROM module on the 10/100 EtherJet
PCI Adapter, the following support and features are provided:
¹The adapters can support DHCP remote boot with DHCP flash
code or RPL remote boot with RPL flash code.
|¹The DHCP LANDesk Service Agent (LSA) code supports both
| Intel's LANDesk Configuration Manager (LCM) and the IBM LAN
| Client Control Manager 2.x (LCCM 2.x).
| The RPL code supports RPL remote boot with IBM LAN Client
| Control Manager 1.1 or 2.x (LCCM 1.1 or LCCM 2.x).
¹The flash diskette provided gives you the option to load the
Flash Module with DHCP code or with RPL code.
You can download this diskette from the Web at:
http://www.networking.ibm.com/nes/nesether.htm.
Select EtherJet 10/100 PCI Adapters and then look for the
DHCP/RPL flash diskette ETPFLSH.EXE.
For further information regarding the DHCP/RPL option, see
Chapter 3, “Dynamic Host Configuration Protocol and Remote
Program Load.”
Prerequisite Operating System PCI Updates
Please check with your operating system supplier for the latest
information concerning required updates to support PCI adapters.
Some currently available operating systems are not PCI-aware, so
the device drivers for the IBM 10/100 EtherJet PCI Adapters are
written to the PCI-architected BIOS or register-level interfaces.
1-4 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Help is available to guide you through manual installation in these
environments. (“Help Files” on page 1-6 describes how to access
help information.)
Kit Contents
| Along with this manual, the adapter kits contain:
¹The IBM 10/100 EtherJet PCI Adapter or the 10/100 EtherJet
PCI Adapter with Wake on LAN
|¹2 Drivers and Installation diskettes
¹
Caution: Safety Information—Read This First
booklet
| In addition to the items listed here, the 10/100 EtherJet PCI Adapter
| with Wake on LAN kit also includes two Wake on LAN cables.
|¹One 08L2558 cable for using with a PC system that has
| separate Wake on LAN power source and Wake on LAN signal
| source connectors
|¹One 08L2559 cable for using with a PC system that has the
| combined 3-pin Wake on LAN connector
If any item is missing or damaged, contact your place of purchase.
Adapter Installation Checklist
To install either adapter, complete the following steps in order. You
might want to mark this page for easy retrieval or make a copy to
use for reference.
1. Preparation
Check the kit contents list on page 1-5.
In addition to the publications shipped with the adapter, you
will need:
¹The manual provided with your PC
¹The manual provided with your network operating system
or network application
¹Your operating system and network application software
Chapter 1. Introducing the Adapters 1-5
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
2. Installing the adapter. See the instructions on page 2-1.
3. Installing the DHCP/RPL option. See the instructions in 3-1.
4. Refer to the help files on your Diagnostics and Help diskette
for:
¹Information about testing the adapter
¹Procedure for installing device drivers
¹Other technical details
See “Help Files” for more information.
Help Information
This includes help files and IBM product support.
Help Files
The help files provide detailed information about the IBM 10/100
EtherJet PCI Adapters. Instructions on how to load the device
drivers from the Device Drivers Diskette are also included.
| To view the help files:
|¹Boot up your system with the Installation diskette and select
|view help files.
|¹Or with the diskette in drive A, switch to that drive and enter from
| a DOS prompt: setup /readme
| Help topics include:
– Latest news and general adapter information
– Hardware specifications and cabling information
– Testing the adapter
– Installing device drivers
– Running diagnostics and error messages
| – New features such as Wake on LAN and Adapter Teaming
1-6 10/100 EtherJet PCI Adapters
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
IBM Product Support
The following IBM product support is available:
¹Download the code from the Internet or the IBM Bulletin Board
System
You can download the latest drivers and related code from the
IBM Internet or the BBS. If you are outside the United States or
Canada, contact your IBM marketing representative for BBS
information.
¹World Wide Web:
– On a Web browser:
1Access URL
http://www.networking.ibm.com/nes/nesether.htm
2Select EtherJet 10/100 PCI Adapters.
You now have access to all the latest drivers and
related code for the IBM EtherJet 10/100 PCI Adapters.
For other information regarding these adapters and
other IBM Networking products, select Network
Environment Support or IBM Networking.
– FTP as Anonymous to lansupport.raleigh.ibm.com,
directory /pubs/products/lanprods/ethernet
Note: At the date of this publication, the BBS telephone number
and Internet Server address are current. If you find that either
the telephone number or the Internet address is not available,
check the README file to see whether a new number or
address is available. (“Help Files” on page 1-6 describes how to
access this information.)
¹IBM PC Company Bulletin Board System (BBS). For a new or
updated version of the installation code or the drivers:
– 1-919-517-0001 (Directory 32) for the United States
– 1-604-664-6464 for Vancouver
– 1-416-956-7877 for Toronto
– 1-514-938-3022 for Montreal
– 1-905-316-4255 for Markham
Chapter 1. Introducing the Adapters 1-7
Title: ASB3CNTL CreationDate: 07/16/98 18:07:52
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/