Siemens LC 48650 Owner's manual

Page is loading ...

14

Appliance description

Operating Instructions

Operating modes

Exhaust-air mode:

❑ The extractor-hood fan extracts the kit-

chen vapours and conveys them through

the grease ﬁlter into the atmosphere.

❑ The grease ﬁlter absorbs the solid

particles in the kitchen vapours.

❑ The kitchen is kept almost free of grease

and odours.

D

When the extractor hood is operated

in exhaust-air mode simultaneously with

a different burner which also makes use

of the same chimney (such as gas, oil or

coal-ﬁred heaters, continuous-ﬂow heaters,

hot-water boilers) care must be taken to

ensure that there is an adequate supply

of fresh air which will be needed by the

burner for combustion.

Safe operation is possible provided that the

underpressure in the room where the

burner is installed does not exceed 4 Pa

(0.04 mbar).

Operating modes

This can be achieved if the combustion air

is able to ﬂow through non-lockable

openings, e.g. in doors, windows and in

conjunction with an air supply/air-intake wall

box or by other technical procedures such

as reciprocal interlocking.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

An air-intake/exhaust-air wall box by itself is

no guarantee that the limiting value will not

be exceeded.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

Unrestricted operation is possible if the

extractor hood is used in recirculating mode

– with activated carbon ﬁlter.

Circulating-air mode:

❑ An activated carbon ﬁlter must be ﬁtted

for this operating mode (see Filters and

maintenance).

 The complete installation set and

replacement ﬁlters can be obtained from

specialist outlets.

The corresponding accessory numbers

can be found at the end of these

operating instructions.

❑ The extractor-hood fan extracts the

kitchen vapours which are puriﬁed in the

grease ﬁlter and activated carbon ﬁlter

and then conveyed back into the

kitchen.

❑ The grease ﬁlter absorbs the grease

particles in the kitchen vapours.

❑ The activated carbon ﬁlter binds the

odorous substances.

 If no activated carbon ﬁlter is installed,

it is not possible to bind the odorous

substances in the cooking vapours.

Lighting

Light / fan

switches

Filter grille

Chimney

panelling

Before using for the ﬁrst time

If you encounter a problem

If you have any questions or if a fault

occurs, please call Customer Service.

(See list of Customer Service

representatives).

When you call, please quote the following:

E-Nr. FD

Enter the relevant numbers into the box

above. The E-Nr. (product no.) and FD

(production date) are shown on the

nameplate which can be seen inside the

extractor hood after the ﬁlter frame has

been detached.

Important notes:

❑ The Instructions for Use apply to several

versions of this appliance. Accordingly,

you may ﬁnd descriptions of individual

features that do not apply to your

speciﬁc appliance.

❑ This extractor hood complies with all

relevant safety regulations.

Repairs should be carried out by

qualiﬁed technicians only.

Improper repairs may put the user at

considerable risk.

❑ Before using your appliance for the ﬁrst

time, please read these Instructions for

Use carefully. They contain important

information concerning your personal

safety as well as on use and care of the

appliance.

❑ Please retain the operating and

installation instructions for a subsequent

owner.

 Do not use the appliance if damaged.

 The appliance may be connected to the

mains by a qualiﬁed technician only.

 The appliance is not intended for use by

young children or inﬁrmed persons

without supervision.

Young children should be supervised to

ensure they do not play with the appliance.

 If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his customer

service or a similarly qualiﬁed person in order

to prevent serious injury to the user.

 Dispose of packaging materials

properly (see Installation instructions).

 This extractor hood is designed for

domestic use only.

 Light bulbs must always be ﬁtted when

the extractor hood is in use.

 Defective bulbs should be replaced

immediately to prevent the remaining bulbs

from overloading.

 Never operate the extractor hood

without a grease ﬁlter.

 Overheated fat or oil can easily catch ﬁre.

If you are cooking with fat or oil, e.g. chips,

etc., never leave the cooker unattended.

 Do not ﬂambé food directly under the

extractor hood.

Risk of grease ﬁlter catching ﬁre due

! to ﬂames.

 The hotplates must always be covered

with a utensil.

 Restrictions apply to the use of the

extractor hood over a solid-fuel burner

(coal, wood, etc.). (See Installation

instructions).

Gas hobs / Gas cookers

 Do not use all the gas hotplates

simultaneously for a prolonged period

(max. 15 minutes) at maximum thermal

load, otherwise there is a risk of burns if the

housing surfaces are touched or a risk of

damage to the extractor hood. If the

extractor hood is situated over a gas hob,

operate the hood at maximum setting if

three or more gas hotplates are operated

simultaneously.

15

16

 The most effective method of removing

vapours produced during cooking is to:

❑ Switch the ventilator ON

as soon as you begin cooking.

❑ Switch the ventilator OFF

a few minutes after you have ﬁnished

cooking.

Operating procedure

Switching the fan ON

❑ Press the + button.

Setting the required fan speed:

❑ Press the + button.

The fan speed is increased by one step.

❑ Press the – button.

The fan speed is reduced by one step.

Switching the fan OFF:

❑ Press the 0 button.

Or:

❑ Keep pressing the – button until the fan

switches off.

Intensive setting:

Maximum power is obtained at the

intensive setting. It is only required for short

intervals.

❑ Keep pressing the + button until a

ç

appears in the display.

❑ If the intensive setting is not cancelled by

hand, the fan will automatically switch

back to step } after 10 minutes.

Filters and maintenance

Grease ﬁlters:

Metal ﬁlters are used to trap the greasy

element of the vapours that develop

during cooking.

The ﬁlter mats are made from non-

combustible metal.

Caution:

As the ﬁlter becomes more and more

saturated with grease, not only does the

risk of it catching ﬁre increase but the

efficiency of the extractor hood can also be

adversely affected.

Important:

By cleaning the metal grease ﬁlters at

appropriate intervals, the possibility of them

catching ﬁre as a result of a build-up of heat

such as occurs when deep-fat frying or

roasting is taking place, is reduced.

Cleaning the metal grease ﬁlters:

❑ In normal operation (1 to 2 hours daily),

the metal grease ﬁlter must be cleaned

after 8 to 10 weeks.

❑ The ﬁlters can be cleaned in a dish-

washer. It is however possible that they

will become slightly discoloured.

❑ The ﬁlter must be placed loosely, and

NOT wedged, in the dishwasher.

Important:

Metal ﬁlters that are saturated with

grease should not be washed together

with other dishes etc.

❑ When cleaning the ﬁlters by hand, soak

them in hot soapy water ﬁrst of all.

Then brush the ﬁlters clean, rinse them

thoroughly and leave the water to drain off.

Lighting:

❑ The light can be switched on at any

time, even though the fan is switched off.

Fan OFF

Light

ON / OFF

0

Reduce fan

speed

Fan ON and

increase speed

Intensive setting

Display for fan setting

Filters and maintenance

3. Engage the lug.

Removing the ﬁlter:

Warning: The halogen bulbs must be

switched off and cool.

1. Remove the metal ﬁlters.

2. Press in the lug and remove the

activated carbon ﬁlter.

2. Insert the activated carbon ﬁlter.Removing and inserting the metal grease

ﬁlters:

Warning: The halogen bulbs must be

switched off and cool.

1. Press the catch on the grease ﬁlters

inwards and fold the ﬁlters down.

2. Clean the ﬁlters.

3. Insert the clean ﬁlters back into the

hood.

Activated carbon ﬁlter:

For neutralizing odours in recirculating

mode.

Caution:

As the ﬁlter becomes more and more

saturated with grease, there is an increased

risk of ﬁre and the function of the extractor

hood may be impaired.

Important:

Change the activated carbon ﬁlter promptly

to prevent the risk of ﬁre from the

accumulation of heat when deep-fat frying

or roasting.

Inserting the ﬁlter:

Warning: The halogen bulbs must be

switched off and cool.

1. Remove the metal ﬁlters

(see "Removing and inserting the metal

grease ﬁlters").

3. Insert the metal grease ﬁlters.

Replacing the activated carbon ﬁlter:

❑ During normal operation (1 to 2 hours

per day) the activated carbon ﬁlters

should be replaced approximately 1 x

year.

❑ A replacement ﬁlter can be obtained

from any authorized dealer (see optional

accessories).

❑ Use original ﬁlters only.

By doing so you will obtain maximum

performance from your extractor hood.

Disposing of the old activated carbon

ﬁlter:

❑ There are no pollutants in the activated

carbon ﬁlters. They can therefore be

disposed of as part of your normal

domestic refuse.

17

18

Cleaning and care

Disconnect the extractor hood from the

electricity supply by pulling out the

mains plug or switching it off at the fuse

box.

❑ At the same time as you clean the

grease ﬁlters, clean off any grease from

all accessible parts of the housing. This

signiﬁcantly reduces the ﬁre hazard and

ensures that the extractor hood

performs as effectively as possible.

❑ Use a hot detergent solution or a mild

window cleaner to clean the canopy of

the extractor hood.

❑ Do not scrape off any dirt that has dried

on but loosen it up with a damp cloth.

❑ Do not use abrasive cleaning agents or

sponges that could cause scratches.

❑ Note: Do not use alcohol (spirit) on

plastic parts, otherwise the surface may

become matt in appearance.

Caution: Ensure that the kitchen is ade-

quately ventilated. Avoid naked ﬂames!

 Clean the operating buttons with a mild

soapy solution and a soft, damp cloth only.

Do not use stainless-steel cleaner to clean

the operating buttons.

Stainless steel surfaces:

❑ Use a mild non-abrasive stainless steel

cleaner.

❑ Clean the surface in the same direction

as it has been ground and polished.

 Do not use any of the following to clean

stainless steel surfaces: abrasive sponges,

cleaning agents containing sand, soda, acid

or chloride!

Aluminium and plastic surfaces:

❑ Use a soft, non-linting window cloth or

micro-ﬁbre cloth.

❑ Do not use dry cloths.

❑ Use a mild window cleaning agent.

❑ Do not use aggressive, acidic or caustic

cleaners.

❑ Do not use abrasive agents.

4. Re-insert the bulb ring.

5. Plug the appliance into the mains or

switch it on at the fuse box.

Note: If the light does not function, check

that the bulbs have been inserted correctly.

Replacing the light bulbs

1. Switch off the extractor hood and pull

out the mains plug or switch off the

electricity supply at the fuse box.

 When switched on, the halogen bulbs

become very hot. Even for some time after

the bulbs have been switched off there is

still a risk of burns.

2. Remove the bulb ring with a screwdriver

or similar tool.

3. Replace the halogen light bulb

(conventional halogen bulb, 12 Volt,

max. 20 Watt, G4 cap).

Caution: Refer for plug-in lampholder.

Take hold of the bulb with a clean cloth.

19

Important information

Installation Instructions:

Additional information concerning gas

cookers:

 When installing gas hotplates, comply

with the relevant national statutory

regulations (e.g. in Germany: Technische

Regeln Gasinstallation TRGI).

 Always comply with the currently valid

regulations and installation instructions

supplied by the gas appliance

manufacturer.

 Only one side of the extractor hood

may be installed next to a high-sided unit

or high wall. Gap at least 50 mm.

 Minimum distance on gas hotplates

between the upper edge of the trivet

and lower edge of the extractor

hood: 650 mm, Fig. 1.

 Old appliances are not worthless

rubbish. Valuable raw materials can be

reclaimed by recycling old appliances.

Before disposing of your old appliance,

render it unusable.

 You received your new appliance in a

protective shipping carton. All packaging

materials are environmentally friendly and

recyclable. Please contribute to a better

environment by disposing of packaging

materials in an environmentally-friendly

manner.

Please ask your dealer or inquire at your

local authority about current means of

disposal.

 The extractor hood can be used in

exhaust air or circulating air mode.

 Always mount the extractor hood over

the centre of the hob.

 Minimum distance between electric

hob and bottom edge of extractor hood:

550 mm, Fig. 1.

The extractor hood must not be

installed over a solid fuel cooker – a

potential ﬁre hazard (e.g. ﬂying sparks) –

unless the cooker features a closed,

non-removable cover and all national

regulations are observed.

 The smaller the gap between the

extractor hood and hotplates, the greater

the likelihood that droplets will form on the

underside of the extractor hood.

20

Prior to installation

Exhaust-air mode

The exhaust air is discharged upwards

through a ventilation shaft or directly

through the outside wall into the open.

D

Exhaust air should neither be directed

into a smoke or exhaust ﬂue that is

currently used for other purposes, nor into

a shaft that is used for ventilating rooms in

which stoves or ﬁreplaces are also located.

Exhaust air may be discharged in

accordance with official and statutory

regulations only (e.g. national building

regulations).

Local authority regulations must be

observed when discharging air into smoke

or exhaust ﬂues that are not otherwise in

use.

D

When the extractor hood is operated

in exhaust-air mode simultaneously with

a different burner which also makes use

of the same chimney (such as gas, oil or

coal-ﬁred heaters, continuous-ﬂow heaters,

hot-water boilers) care must be taken to

ensure that there is an adequate supply

of fresh air which will be needed by the

burner for combustion.

Safe operation is possible provided that the

underpressure in the room where the

burner is installed does not exceed 4 Pa

(0.04 mbar).

This can be achieved if combustion air can

ﬂow through non-lockable openings, e.g. in

doors, windows and via the air-

intake/exhaust-air wall box or by other

technical measures, such as reciprocal

interlocking, etc.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

An air-intake/exhaust-air wall box by itself

is no guarantee that the limiting value will

not be exceeded.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

Unrestricted operation is possible if the

extractor hood is used in recirculating

mode – with activated carbon ﬁlter.

120

150

120

150

280

260

min. 45

684-1083

136

min.

600

min

550

min.60

520

600/900

21

Prior to installation

For optimum extractor hood efficiency:

❑

Short, smooth air exhaust pipe.

❑

As few bends in the pipe as possible.

❑

Diameter of pipe to be as large as

possible and no tight bends in pipe.

If long, rough exhaust-air pipes,

many pipe bends or smaller pipe

diameters are used, the air extraction

rate will no longer be at an optimum

level and there will be an increase in

noise.

❑

Round pipes:

We recommend

Internal diameter: 150 mm (at least

120 mm).

❑

Flat ducts must have an internal cross-

section that equates to that of round

pipes.

There should be no sharp bends.

l 120 mm approx. 113 cm

2

l 150 mm approx. 177 cm

2

❑

If pipes have different diameters:

Insert sealing strip.

❑

For exhaust-air mode, ensure that

there is an adequate supply of fresh air.

Circulating-air mode

❑ With activated carbon ﬁlter if exhaust-air

mode is not possible.

Connecting a l 150 mm exhaust-air

pipe:

❑

Mount the pipe directly onto the air

outlet on the hood.

Connecting a l 120 mm exhaust-air

pipe:

❑ Attach the reducing connector directly to

the air pipe.

 The complete

installation set can be

obtained from

specialist outlets.

The corresponding

accessory numbers

can be found at the

end of these operating

instructions.

280

260

min.136

775-1179

40

min.

600

520

600/900

❑ Attach the exhaust-air pipe to the

reducing connector.

22

Electrical connection

Electrical data:

Are to be found on the name plate inside

the appliance after removal of the ﬁlter

frame.

 Before undertaking any repairs,

always disconnect the extractor hood from

the electricity supply.

Length of the connecting cable: 1.30 m.

If it is necessary to wire the extractor

hood directly into the mains:

The extractor hood should only be

connected to the electricity supply by a

properly qualiﬁed electrician.

A separator must be installed in the

household circuit. A suitable separator is a

switch that has a contact gap of more than

3 mm and interrupts all poles. Such

devices include circuit breakers and

contactors.

 If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his

customer service or a similarly qualiﬁed

person in order to prevent serious injury to

the user.

This extractor hood corresponds to EC

regulations concerning RF interference

suppression.

Electrical connection

WARNING: THIS APPLIANCE MUST BE

EARTHED

IMPORTANT: Fitting a Different Plug:

The wires in the mains lead are coloured in

accordance with the following code:

Green and Yellow – Earth

Blue – Neutral

Brown – Live

If you ﬁt your own plug, the colours of

these wires may not correspond with the

identifying marks on the plug terminals.

This is what you have to do:

1.Connect the green and yellow (Earth)

wire to the terminal in the plug marked

‘E’ or with the symbol ( ), or

coloured green or green and yellow.

2.Connect the blue (Neutral) wire to the

terminal in the plug marked ‘N’ or

coloured black.

3.Connect the brown (Live) wire to the

terminal marked ‘L’, or coloured red.

The extractor hood should only be

connected to an earthed socket that has

been installed according to relevant

regulations.

If possible, site the earthed socket directly

behind the chimney panelling.

Weight in kg:

Exhaust air Recirculating air

19,560 cm

90 cm

20,0

22,0 22,5

We reserve the right to construction changes within the

context of technical development.

Prior to installation

Preparing the wall

❑ The wall must be ﬂat and perpendicular.

❑ Ensure that the wall is capable of

providing a ﬁrm hold for mounting

screws and plugs.

23

Installation

This extractor hood is intended to be

mounted onto the kitchen wall.

1. Remove the grease ﬁlter

(refer to Operating Instructions).

2. Draw a line on the wall from the ceiling

to the lower edge of the hood at the

centre of the location where the hood is

going to be mounted.

3. Use the template to mark the points on

the wall where the screws will be

mounted. In order to make it easier to

hook the hood onto the screws, draw

the outline of the area where the hood

will be attached.

 Ensure that the minimum distance bet-

ween the hob and the extractor hood is

maintained – 550 mm for an electric hob

and 650 mm for a gas hob. The bottom

edge of the template equates to the lower

edge of the extractor hood.

4. Drill 4 x l 8 mm holes for the extractor

hood and 2 x l 8 mm holes for the

chimney panelling. Insert plugs into the

holes so that they are ﬂush with the wall.

7. Attach the extractor hood.

Adjust the height and align horizontally

with the adjusting screws.

Note: Take into account any special

accessories that are going to be ﬁtted.

5. Attach the 2 enclosed spacers to the

ﬁxing bracket for the ﬂue duct panelling.

6. Screw on the upper and the two lower

ﬁxing brackets.

3

0

172

476

36,5

400

min.550 Elektro

min.650 Gas

216

24

Installation

08. Screw in lower screws (hex screws).

09. Stick protective ﬁlm over the holes of

the 2 lower mounting bolts in the

protective grid.

12. Remove the protective ﬁlm from the

two ﬂue ducts.

 Take care not to damage the

surfaces which are susceptible to

scratches etc.

13. Push both sections of the ﬂue panelling

together (slots in the upper section

must be pointing downwards) and

insert into the opening in the extractor

hood.

 Protect the cover panels from

scratches, for example by laying the

template used for marking the wall over

the top edge of the lower section.

10. Connect up the air outlet pipe.

11. Connect the hood to the electricity

supply.

14. Slide out the upper section and attach

it to the mounting brackets at the sides

with two screws.

1.

2.

3.

15. Insert the grease ﬁlter (refer to

Operating Instructions).

1.

2.

Page is loading ...

128

Notities

Page is loading ...

Siemens LC 48650 Owner's manual

Siemens LC 48650 Owner's manual

in other languages

Related papers

Other documents