Pioneer DEH-1500UBA User manual

Owner’s Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

Руководство пользователя

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

DEH-1500UB

DEH-1500UBG

DEH-1500UBA

DEH-1500UBB

English NederlandsDeutschEspañolItalianoFrançais Русский

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is especially

important that you read and observe WARN-

INGs and CAUTIONs in this manual. Please

keep the manual in a safe and accessible place for

future reference.

If you want to dispose this product, do not

mix it with general household waste. There is

a separate collection system for used elec-

tronic products in accordance with legislation

that requires proper treatment, recovery and

recycling.

Private households in the member states of the

EU, in Switzerland and Norway may return their

used electronic products free of charge to desig-

nated collection facilities or to a retailer (if you

purchase a similar new one).

For countries not mentioned above, please con-

tact your local authorities for the correct method

of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment, re-

covery and recycling and thus prevent potential

negative effects on the environment and human

health.

About this unit

The tuner frequencies on this unit are allocated

for use in Western Europe, Asia, the Middle

East, Africa and Oceania. Use in other areas

may result in poor reception. The RDS (radio

data system) function only operates in areas

with broadcasting RDS signals for FM stations.

CAUTION

This product is a class 1 laser product classi-

fied under the Safety of laser products, IEC

60825-1:2007.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with

liquids.

! The Pioneer CarStereo-Pass is for use only in

Germany.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture.

! If the battery is disconnected or discharged,

any preset memory will be erased.

Note

Function setting operations are completed even

if the menu is canceled before the operations

are confirmed.

About this manual

In the following instructions, USB memories

and USB audio players are collectively referred

to as “USB storage device”.

In case of trouble

Should this unit fail to operate properly, please

contact your dealer or nearest authorized

PIONEER Service Station.

Before you start

2

Section

Before you start

En

01

Head unit

c d

5

9

1 2 3 4 6 7

bae8

Part Part

1 h (eject) 8

(equalizer)

2 SRC/OFF 9 BAND

3

MULTI-CONTROL

(M.C.)

a

(back)/

DIMMER

(dimmer)

4

(list) b c/d

5 DISP c 1/

to 6/

6 Disc loading slot d

AUX input jack

(3.5 mm stereo

jack)

7 USB port e Detach button

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB storage device as

any device connected directly to the unit will

protrude out from the unit, which could be

dangerous.

! Do not use unauthorized products.

Display indication

21 3 75

9

4 6 8

a

Indicator State

1

(list)

The list function is being oper-

ated.

2

Sub infor-

mation sec-

tion

Sub information is displayed.

3

TA (traffic

announce-

ments)

TA function is on.

4

TP (traffic

program

identifica-

tion)

A TP station is tuned in.

5

(sound re-

triever)

The sound retriever function

is on.

6 LOC Local seek tuning is on.

7

(repeat) Track or folder repeat is on.

8

(ran-

dom)

Random play is on.

Indicator State

9

Main infor-

mation sec-

tion

! Tuner: band and fre-

quency

! RDS: program service

name, PTY information

and other literal informa-

tion

! CD player and USB stor-

age device: elapsed play-

back time and text

information

a

Appears when a lower tier of

folder or menu exists.

Set up menu

When you turn the ignition switch to ON after in-

stallation, set up menu appears on the display.

You can set up the menu options below.

1 After installation of this unit, turn the

ignition switch to ON.

SET UP appears.

2 Turn M.C. to switch to YES.

# If you do not operate for 30 seconds, the set up

menu will not be displayed.

# If you prefer not to set up at this time, turn M.C.

to switch to NO. Press to select.

If you select NO, you cannot set up in the set up

menu.

3 Press M.C. to select.

4 Perform the following procedures to set

the menu.

To proceed to the next menu option, you need to

confirm your selection.

LANGUAGE (multi-language)

This unit can display the text information from a

compressed audio file even for information em-

bedded in English or Russian.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

ENG (English)—РУС (Russian)

2 Press M.C. to confirm the selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour.

2 Press M.C. to select minute.

3 Turn M.C. to adjust minute.

4 Press M.C. to confirm the selection.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

! The tuning step remains at 50 kHz during man-

ual tuning.

1 Turn M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

2 Press M.C. to confirm the selection.

QUIT appears.

5 To finish your settings, turn M.C. to select

YES.

# If you prefer to change your setting again, turn

M.C. to switch to NO. Press to select.

6 Press M.C. to select.

English

Operating this unit

3

Section

Operating this unit

En

02

Notes

! You can set up the menu options from the

system menu. For details about the settings,

refer to System menu on page 7.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached

to the front panel before detaching it.

Removing the front panel to protect your unit from

theft

1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (N) you.

3 Always keep the detached front panel in a pro-

tection device such as a protection case.

Re-attaching the front panel

1 Slide the front panel to the left.

Make sure to insert the tabs on the left side of

the head unit into the slots on the front panel.

2 Press the right side of the front panel until it is

firmly seated.

If you cannot attach the front panel to the

head unit successfully, make sure that you are

placing the front panel onto the head unit cor-

rectly. Forcing the front panel into place may

result in damage to the front panel or head

unit.

Turning the unit on

1 Press SRC/OFF to turn the unit on.

Turning the unit off

1 Press and hold SRC/OFF until the unit turns

off.

Selecting a source

1 Press SRC/OFF to cycle between:

TUNER (tuner)—CD (CD player)—USB (USB)

—AUX (AUX)

Adjusting the volume

1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when re-

moving the front panel.

Note

When this unit’s blue/white lead is connected to

the vehicle’s auto-antenna relay control termi-

nal, the vehicle’s antenna extends when this

unit’s source is turned on. To retract the anten-

na, turn the source off.

Frequently used menu

operations

Returning to the previous display

Returning to the previous list (the folder one level

higher)

1 Press

/DIMMER.

Returning to the ordinary display

Canceling the main menu

1 Press BAND.

Returning to the ordinary display from the list

1 Press BAND.

Tuner

Basic operations

Selecting a band

1 Press BAND until the desired band (FM1,

FM2, FM3 for FM or MW/LW) is displayed.

Switching preset stations

1 Press c or d.

! Select PCH (preset channel) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

the next page.

Manual tuning (step by step)

1 Press c or d.

! Select MAN (manual tuning) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

the next page.

Seeking

1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing

c or d.

While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as

you release c or d.

Note

This unit’s AF (alternative frequencies search)

function can be turned on and off. AF should be

off for normal tuning operation (refer to AF (al-

ternative frequencies search) on the next page).

Storing and recalling stations

for each band

Using preset tuning buttons

1 When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1/

to 6/ ) and hold until

the preset number stops flashing.

Operating this unit

4

Section

Operating this unit

En

02

2 Press one of the preset tuning buttons

(1/

to 6/ ) to select the desired station.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! FREQUENCY (program service name or

frequency)

! BRDCST INFO (program service name/PTY

information)

! CLOCK (source name and clock)

Notes

! If the program service name cannot be ac-

quired in FREQUENCY, the broadcast fre-

quency is displayed instead. If the program

service name is detected, the program serv-

ice name will be displayed.

! BRDCST INFO text information will change

automatically.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Using PTY functions

You can tune in to a station using PTY (program

type) information.

Searching for an RDS station by PTY information

You can search for general types of broadcasting

programs, such as those listed in the following

section. Refer to this page.

1 Press

(list).

2 Turn M.C. to select a program type.

NEWS/INFO—POPULAR—CLASSICS—

OTHERS

3 Press M.C. to begin the search.

The unit searches for a station broadcasting

that type of program. When a station is found,

its program service name is displayed.

! To cancel the search, press M.C. again.

! The program of some stations may differ

from that indicated by the transmitted PTY.

! If no station is broadcasting the type of

program you searched for, NOT FOUND is

displayed for about two seconds and then

the tuner returns to the original station.

PTY list

NEWS/INFO (news and information)

NEWS (News), AFFAIRS (Current affairs), INFO

(Information), SPORT (Sports), WEATHER (Weath-

er), FINANCE (Finance)

POPULAR (popular)

POP MUS (Popular music), ROCK MUS (Rock

music), EASY MUS (Easy listening), OTH MUS

(Other music), JAZZ (Jazz), COUNTRY (Country

music), NAT MUS (National music), OLDIES

(Oldies music), FOLK MUS (Folk music)

CLASSICS (classics)

L. CLASS (Light classical), CLASSIC (Classical)

OTHERS (others)

EDUCATE (Education), DRAMA (Drama), CUL-

TURE (Culture), SCIENCE (Science), VARIED (Var-

ied), CHILDREN (Children’s), SOCIAL (Social

affairs), RELIGION (Religion), PHONE IN (Phone

in), TOURING (Travel), LEISURE (Leisure), DOCU-

MENT (Documentaries)

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

# If MW/LW band is selected, only BSM, LOCAL

and SEEK are available.

BSM (best stations memory)

BSM (best stations memory) automatically stores

the six strongest stations in the order of their sig-

nal strength.

1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

REGION (regional)

When AF is used, the regional function limits the

selection of stations to those broadcasting region-

al programs.

1 Press M.C. to turn the regional function on or

off.

LOCAL (local seek tuning)

Local seek tuning lets you tune in to only those

radio stations with sufficiently strong signals for

good reception.

1 Press M.C. to select the desired setting.

FM: OFF—LV1—LV2—LV3—LV4

MW/LW: OFF—LV1 —LV2

The highest level setting allows reception of

only the strongest stations, while lower levels

allow the reception of weaker stations.

TA (traffic announcement standby)

1 Press M.C. to turn traffic announcement

standby on or off.

AF (alternative frequencies search)

1 Press M.C. to turn AF on or off.

NEWS (news program interruption)

1 Press M.C. to turn the NEWS function on or

off.

SEEK (left/right key setting)

You can assign a function to the left and right keys

of the unit.

Select MAN (manual tuning) to tune up or down

manually or select PCH (preset channel) to switch

between preset channels.

1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB

storage devices

Basic operations

Playing a CD/CD-R/CD-RW

1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW

1 Press h.

English

Operating this unit

5

Section

Operating this unit

En

02

Playing songs on a USB storage device

1 Open the USB port cover.

2 Plug in the USB storage device using a USB

cable.

Playback is performed automatically.

Stopping playback of files on a USB storage de-

vice

1 You may disconnect the USB storage device at

any time.

The unit stops playback.

Selecting a folder

1 Press 1/

or 2/ .

Selecting a track

1 Press c or d.

Fast forwarding or reversing

1 Press and hold c or d.

! When playing compressed audio, there is no

sound during fast forward or reverse.

Returning to root folder

1 Press and hold BAND.

Switching between compressed audio and CD-DA

1 Press BAND.

Switching between playback memory devices

You can switch between playback memory devices

on USB storage devices with more than one Mass

Storage Device-compatible memory device.

1 Press BAND.

! You can switch between up to 32 different

memory devices.

Note

Disconnect USB storage devices from the unit

when not in use.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

CD-DA

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

CD-TEXT

! TRACK INFO (track title/track artist/disc

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

MP3/WMA/WAV

! TRACK INFO (track title/artist name/album

title)

! FILE INFO (file name/folder name)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)

! SPEANA (spectrum analyzer)

Notes

! TRACK INFO and FILE INFO text information

will change automatically.

! Depending on the version of iTunes used to

write MP3 files to a disc or media file types,

incompatible text stored within an audio file

may be displayed incorrectly.

! Text information items that can be changed

depend on the media.

Selecting and playing files/

tracks from the name list

1 Press to switch to the file/track name

list mode.

2 Use M.C. to select the desired file name

(or folder name).

Selecting a file or folder

1 Turn M.C.

Playing

1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the se-

lected folder

1 When a folder is selected, press M.C.

Playing a song in the selected folder

1 When a folder is selected, press and hold M.C.

Operations using special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks

! ONE – Repeat the current track

! FLD – Repeat the current folder

USB storage device

! ALL – Repeat all files

! ONE – Repeat the current file

! FLD – Repeat the current folder

Playing tracks in random order

1 Press 5/

to turn random play on or off.

Tracks in a selected repeat range are played in

random order.

! To change songs during random play, press d

to switch to the next track. Pressing c restarts

playback of the current track from the begin-

ning of the song.

Pausing playback

1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

Once selected, the function below can be ad-

justed.

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on this page.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select AUDIO.

3 Turn M.C. to select the audio function.

Once selected, the following audio functions

can be adjusted.

! FADER is not available when SUB.W/SUB.W

is selected in SP-P/O MODE. For details, refer

to SP-P/O MODE (rear output and preout set-

ting) on page 8.

Operating this unit

6

Section

Operating this unit

En

02

! SUB.W, SUB.W CTRL and HPF SETTING are

not available when REAR/REAR is selected in

SP-P/O MODE. For details, refer to

SP-P/O MODE (rear output and preout set-

ting) on the next page.

! SUB.W CTRL and HPF SETTING are not avail-

able when SUB.W is selected in OFF. For de-

tails, refer to SUB.W (subwoofer on/off

setting) on this page.

FADER (fader adjustment)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the front/rear speaker bal-

ance.

BALANCE (balance adjustment)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the left/right speaker bal-

ance.

EQ SETTING (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUS-

TOM1—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be

customized when CUSTOM1 or CUSTOM2 is

selected.

If selecting CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting

other options, press M.C. to return to the pre-

vious display.

! CUSTOM1 can be set separately for each

source.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode.

4 Press M.C. to cycle between the following:

Equalizer band—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—

2.5KHZ—8KHZ

Equalizer level: +6 to –6

! You can also switch the equalizer by pressing

repeatedly.

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level

Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Output level: –24 to +6

Slope level: –6 — –12

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or

decreased.

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the sub-

woofer output frequency range to play from the

front or rear speakers, turn on the HPF (high pass

filter). Only frequencies higher than those in the

selected range are output from the front or rear

speakers.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the following:

Cut-off frequency—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ

Slope level: –6 — –12

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

System menu

Important

PW SAVE (power saving) is canceled if the ve-

hicle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depend-

ing on connection methods, the unit may con-

tinue to draw power from the battery if your

vehicle’s ignition doesn’t have an ACC (acces-

sory) position.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select SYSTEM.

3 Turn M.C. to select the system menu

function.

Once selected, the following system menu func-

tions can be adjusted.

! MUTE MODE and PW SAVE are not available

for DEH-1500UBA.

English

Operating this unit

7

Section

Operating this unit

En

02

LANGUAGE (multi-language)

This unit can display the text information from a

compressed audio file even for information em-

bedded in English or Russian.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

ENG (English)—РУС (Russian)

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

12H/24H (time notation)

1 Press M.C. to select the desired setting.

12H (12-hour clock)—24H (24-hour clock)

AUTO PI (auto PI seek)

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary de-

vice connected to this unit.

1 Press M.C. to turn AUX on or off.

MUTE MODE (mute mode)

Sound from this system is automatically muted or

attenuated when a signal from equipment with a

mute function is received.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

You can select any one of the options in the fol-

lowing list:

! MUTE – Muting

! 20dB ATT – Attenuation (20dB ATT has a

stronger effect than 10dB ATT)

! 10dB ATT – Attenuation

PW SAVE (power saving)

Switching this function on enables you to reduce

the consumption of battery power.

! Turning on the source is the only operation al-

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

Switching the dimmer setting

You can adjust the brightness of illumination.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to

select.

3 Press M.C. to select the desired setting.

OFF (off)—ON (on)

! You can also change the dimmer setting by

pressing and holding

/DIMMER.

Initial menu

1 Press and hold SRC/OFF until the unit

turns off.

2 Press and hold SRC/OFF until the main

menu appears in the display.

3 Turn M.C. to change the menu option

and press to select INITIAL.

4 Turn M.C. to select the initial menu func-

tion.

Once selected, the following initial menu func-

tions can be adjusted.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

! The tuning step remains at 50 kHz during man-

ual tuning.

1 Press M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output

of this unit can be used to connect a full-range

speaker or subwoofer. Select a suitable option for

your connection.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

You can select any one of the options in the fol-

lowing list:

! REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speak-

er leads output and there is a subwoofer

connected to the RCA output.

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear

speaker leads output without any auxiliary

amp and there is a subwoofer connected

to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speak-

er leads output and the RCA output.

If there is a full-range speaker connected to

the rear speaker leads output and the RCA

output is not used, you may select either

REAR/SUB.W or REAR/REAR.

System menu

1 Press and hold SRC/OFF until the unit

turns off.

2 Press and hold SRC/OFF until the main

menu appears in the display.

3 Turn M.C. to change the menu option

and press to select SYSTEM.

4 Turn M.C. to select the system menu

function.

Once selected, the following system menu func-

tions can be adjusted.

Operating this unit

8

Section

Operating this unit

En

02

For details, refer to System menu on page 7.

Using an AUX source

1 Insert the stereo mini plug into the AUX

input jack.

2 Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on the previous page.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! Source name

! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the proce-

dures listed below.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select SYSTEM.

3 Turn M.C. to display DEMO OFF and press

to select.

4 Turn M.C. to switch to YES.

5 Press M.C. to select.

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 W to

8 W (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

This unit

3 45

21

1 Power cord input

2 Rear output or subwoofer output

3 Antenna input

4 Fuse (10 A)

5 Wired remote input (DEH-1500UBG, DEH-

1500UBB and DEH-1500UB only)

Hard-wired remote control adapter can be

connected (sold separately).

English

Operating this unit

9

Section

Installation

En

02

03

Power cord

1

3

2

4

5

6

b

8

9

7

a

e

d

c

1 To power cord input

2 Depending on the kind of vehicle, the func-

tion of 3 and 5 may be different. In this

case, be sure to connect 4 to 5 and 6 to

3.

3 Yellow

Back-up (or accessory)

4 Yellow

Connect to the constant 12 V supply termi-

nal.

5 Red

Accessory (or back-up)

6 Red

Connect to terminal controlled by ignition

switch (12 V DC).

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

9 Blue/white

The pin position of the ISO connector will dif-

fer depending on the type of vehicle. Connect

9 and b when Pin 5 is an antenna control

type. In another type of vehicle, never con-

nect 9 and b.

a Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

b Blue/white

Connect to auto-antenna relay control termi-

nal (max. 300 mA 12 V DC).

c Yellow/black (DEH-1500UBG, DEH-1500UBB

and DEH-1500UB only)

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

d Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

e ISO connector

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to con-

nect to both connectors.

Notes

! Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout set-

ting) on page 8.

The subwoofer output of this unit is monau-

ral.

! When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.









1

3

2

4

55

1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Rear output or subwoofer output

5 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel and

wrap any loose cables so they are not block-

ing the vents.

5cmcm

Leave ample

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

Installation

10

Section

Installation

En

03

2 Mounting sleeve

# Make sure that the unit is installed securely in

place. An unstable installation may cause skipping

or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position

where the holes on the bracket and the side

of the unit match.

2 Tighten two screws on each side.

1

2

3

1 Tapping screw (5 mm × 8 mm)

2 Mounting bracket

3 Dashboard or console

Removing the unit

1 Remove the trim ring.

1 Trim ring

2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front

panel

You can remove the front panel to protect your

unit from theft.

Press the detach button and push the front

panel upward and pull it toward you.

For details, refer to Removing the front panel to

protect your unit from theft and Re-attaching the

front panel on page 4.

Troubleshooting

Symptom Cause Action

The display

automatically

returns to the

ordinary dis-

play.

You did not per-

form any opera-

tion within

about 30 sec-

onds.

Perform operation

again.

The repeat

play range

changes un-

expectedly.

Depending on

the repeat play

range, the se-

lected range

may change

when another

folder or track is

being selected

or during fast

forwarding/re-

versing.

Select the repeat

play range again.

A subfolder is

not played

back.

Subfolders can-

not be played

when FLD (fold-

er repeat) is se-

lected.

Select another re-

peat play range.

NO XXXX ap-

pears when a

display is

changed (NO

TITLE, for ex-

ample).

There is no em-

bedded text in-

formation.

Switch the display

or play another

track/file.

The unit is

malfunction-

ing.

There is inter-

ference.

You are using a

device, such as

a cellular

phone, that

transmits elec-

tric waves near

the unit.

Move electrical

devices that may

be causing the in-

terference away

from the unit.

Error messages

When you contact your dealer or your nearest

Pioneer Service Center, be sure to note the error

message.

Common

Message Cause Action

AMP ERROR Unit fails to op-

erate or speaker

connection is

incorrect; pro-

tective circuit is

activated.

Check the speak-

er connection. If

the message fails

to disappear even

after the engine is

switched off/on,

contact your deal-

er or an author-

ized Pioneer

Service Station

for assistance.

CD player

Message Cause Action

ERROR-07,

11, 12, 17, 30

The disc is dirty. Clean the disc.

The disc is

scratched.

Replace the disc.

ERROR-07,

10, 11, 12,

15, 17, 30,

A0

There is an elec-

trical or me-

chanical error.

Turn the ignition

switch OFF and

back ON, or

switch to a differ-

ent source, then

back to the CD

player.

ERROR-15 The inserted

disc is blank.

Replace the disc.

ERROR-23 Unsupported

CD format.

Replace the disc.

English

Installation

11

Section

Additional information

En

03

Message Cause Action

FORMAT

READ

Sometimes

there is a delay

between the

start of playback

and when you

start to hear any

sound.

Wait until the

message disap-

pears and you

hear sound.

NO AUDIO The inserted

disc does not

contain any

playable files.

Replace the disc.

SKIPPED The inserted

disc contains

DRM protected

files.

Replace the disc.

PROTECT All the files on

the inserted

disc are em-

bedded with

DRM.

Replace the disc.

USB storage device

Message Cause Action

FORMAT

READ

Sometimes

there is a delay

between the

start of playback

and when you

start to hear any

sound.

Wait until the

message disap-

pears and you

hear sound.

NO AUDIO There are no

songs.

Transfer the audio

files to the USB

storage device

and connect.

The connected

USB storage de-

vice has secur-

ity enabled.

Follow the USB

storage device in-

structions to dis-

able the security.

Message Cause Action

SKIPPED The connected

USB storage de-

vice contains

files embedded

with Windows

Mediaä DRM 9/

10.

Play an audio file

not embedded

with Windows

Media DRM 9/10.

PROTECT All the files in

the USB storage

device are em-

bedded with

Windows Media

DRM 9/10.

Transfer audio

files not em-

bedded with

Windows Media

DRM 9/10 to the

USB storage de-

vice and connect.

N/A USB The USB device

connected to is

not supported

by this unit.

! Connect a USB

Mass Storage

Class compliant

device.

! Disconnect

your device and

replace it with a

compatible USB

storage device.

CHECK USB The USB con-

nector or USB

cable has short-

circuited.

Check that the

USB connector or

USB cable is not

caught in some-

thing or dam-

aged.

The connected

USB storage de-

vice consumes

more than maxi-

mum allowable

current.

Disconnect the

USB storage de-

vice and do not

use it. Turn the

ignition switch to

OFF, then to ACC

or ON and then

connect only

compliant USB

storage devices.

Message Cause Action

ERROR-19 Communication

failed.

Perform one of

the following op-

erations.

–Turn the ignition

switch OFF and

back ON.

–Disconnect the

USB storage de-

vice.

–Change to a dif-

ferent source.

Then, return to

the USB source.

ERROR-23 USB storage de-

vice was not for-

matted with

FAT12, FAT16 or

FAT32.

USB storage de-

vice should be for-

matted with

FAT12, FAT16 or

FAT32.

STOP There are no

songs in the

current list.

Select a list that

contains songs.

Handling guidelines

Discs and player

Use only discs that feature either of the following

two logos.

Use 12-cm discs. Do not use 8-cm discs or an

adapter for 8-cm discs.

Use only conventional, fully circular discs. Do not

use shaped discs.

Do not insert anything other than a CD into the

CD loading slot.

Do not use cracked, chipped, warped, or other-

wise damaged discs as they may damage the play-

er.

Unfinalized CD-R/RW discs cannot be played

back.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals

to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth out-

ward from the center.

Condensation may temporarily impair the player’s

performance. Let it rest for about one hour to ad-

just to a warmer temperature. Also, wipe any

damp discs off with a soft cloth.

Playback of discs may not be possible because of

disc characteristics, disc format, recorded applica-

tion, playback environment, storage conditions,

and so on.

Road shocks may interrupt disc playback.

Read the precautions for discs before using them.

Additional information

12

Appendix

Additional information

En

When using discs that can be printed on label sur-

faces, check the instructions and the warnings of

the discs. Depending on the discs, inserting and

ejecting may not be possible. Using such discs

may result in damage to this equipment.

Do not attach commercially available labels or

other materials to the discs.

! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result

in damage to the equipment.

USB storage device

Address any questions you have about your USB

storage device to the manufacturer of the device.

Connections via USB hub are not supported.

Do not connect anything other than a USB stor-

age device.

Firmly secure the USB storage device when driv-

ing. Do not let the USB storage device fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Depending on the USB storage device, the follow-

ing problems may occur.

! Operations may vary.

! The storage device may not be recognized.

! Files may not be played back properly.

! The device may generate noise in the radio.

DualDiscs

DualDiscs are two-sided discs that have a record-

able CD for audio on one side and a recordable

DVD for video on the other.

Since the CD side of DualDiscs is not physically

compatible with the general CD standard, it may

not be possible to play the CD side with this unit.

Frequent loading and ejecting of a DualDisc may

result in scratches on the disc. Serious scratches

can lead to playback problems on this unit. In

some cases, a DualDisc may become stuck in the

disc loading slot and will not eject. To prevent this,

we recommend you refrain from using DualDisc

with this unit.

Please refer to the information from the disc man-

ufacturer for more detailed information about

DualDiscs.

Compressed audio

compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to

384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless,

Voice/DRM Stream/Stream with video: Not com-

patible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is given priority over Version

1.x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS

ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

Supplemental information

Only the first 32 characters can be displayed as a

file name (including the file extension) or a folder

name.

Russian text to be displayed on this unit should be

encoded in one of the following character sets:

! Unicode (UTF-8, UTF-16)

! A character set other than Unicode that is

used in a Windows environment and is set to

Russian in the multi-language setting

This unit may not operate correctly depending on

the application used to encode WMA files.

There may be a slight delay at the start of playback

of audio files embedded with image data or audio

files stored on a USB storage device that has nu-

merous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections be-

tween the songs from the original recording, com-

pressed audio discs play with a short pause

between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compati-

ble

Partitioned USB storage device: Only the first par-

tition can be played.

There may be a slight delay when starting play-

back of audio files on a USB storage device with

numerous folder hierarchies.

CAUTION

! Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes

no responsibility for any loss of data on

media players, smart phones, or other devi-

ces while using this product.

! Do not leave discs or a USB storage device

in any place that is subject to high tempera-

tures.

Sequence of audio files

The user cannot assign folder numbers and

specify playback sequences with this unit.

English

Additional information

13

Appendix

Additional information

En

Example of a hierarchy













Level 1 Level 2 Level 3 Level 4

01

02

03

04

05

: Folder

: Compressed

audio file

01 to 05: Folder

number

1 to 6: Playback

sequence

Disc

Folder selection sequence or other operation

may differ depending on the encoding or writing

software.

USB storage device

Playback sequence is the same as recorded se-

quence in the USB storage device.

To specify the playback sequence, the following

method is recommended.

1 Create a file name that includes numbers

that specify the playback sequence (e.g.,

001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.

3 Save the folder containing files on the USB

storage device.

However, depending on the system environment,

you may not be able to specify the playback se-

quence.

For USB portable audio players, the sequence is

different and depends on the player.

Russian character chart

D: C D: C D: C D: C D: C

: А : Б : В : Г : Д

: Е, Ё : Ж : З : И, Й : К

: Л : М : Н : О : П

D: C D: C D: C D: C D: C

: Р : С : Т : У : Ф

: Х : Ц : Ч

: Ш,

Щ

: Ъ

: Ы : Ь : Э : Ю : Я

D: Display C: Character

Copyright and trademark

iTunes

Apple and iTunes are trademarks of Apple Inc.,

registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for

private, non-commercial use and does not con-

vey a license nor imply any right to use this prod-

uct in any commercial (i.e. revenue-generating)

real time broadcasting (terrestrial, satellite,

cable and/or any other media), broadcasting/

streaming via internet, intranets and/or other

networks or in other electronic content distribu-

tion systems, such as pay-audio or audio-on-de-

mand applications. An independent license for

such use is required. For details, please visit

http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark

or trademark of Microsoft Corporation in the

United States and/or other countries.

This product includes technology owned by

Microsoft Corporation and cannot be used or

distributed without a license from Microsoft

Licensing, Inc.

Specifications

General

Power so urce ................... 14.4 V DC (10.8 V to 15.1 V al-

lowable)

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

DIN

Chassis .............. 178mm × 50mm ×

165 mm

Nose .................. 188 mm × 58mm ×

16 mm

D

Chassis .............. 178mm × 50mm ×

165 mm

Nose .................. 170 mm × 46mm ×

16 mm

Weight ............................. 1kg

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 W (for subwoofer)

Continuous power output

................................... 22W × 4 (50 Hz to 15000Hz,

5 % THD, 4 W load, both chan-

nels driven)

Load impedance .............. 4W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0V

Loudness contour ............ +10dB (100 Hz), +6.5 dB

(10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency ................. 80Hz/250 Hz/800 Hz/

2.5 kHz/8 kHz

Equalization range .... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency ................. 50Hz/63 Hz/80 Hz/100 Hz/

125 Hz/160 Hz/200 Hz

Slope ........................ –6 dB/oct, –12 dB/oct

Gain ......................... +6dB to –24 dB

Phase ....................... Normal/Reverse

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94dB (1kHz) (IEC-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range .............. 87.5 MHz to 108.0 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

30 dB)

Signal-to-noise ratio ......... 72dB (IEC-A network)

MW tuner

Frequency range .............. 531 kHz to 1 602kHz

Usable sensitivity ............. 25µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62dB (IEC-A network)

LW tuner

Frequency range .............. 153 kHz to 281 kHz

Usable sensitivity ............. 28µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62dB (IEC-A network)

Note

Specifications and the design are subject to

modifications without notice.

Additional information

14

Appendix

Additional information

En

English

15En

Page is loading ...

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,

Kanagawa 212-0031, JAPAN

Корпорация Пайонир

1-1, Син-Огура, Сайвай-ку, г. Кавасаки,

префектура Канагава,

212-0031, Япония

Импортер ООО “ПИОНЕР РУС”

125040, Россия, г. Москва, ул. Правды, д.26

Тел.: +7(495) 956-89-01

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada

TEL: 1-877-283-5901

TEL: 905-479-4411

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

先鋒股份有限公司

台北市內湖區瑞光路407號8樓

電話： 886-(0)2-2657-3588

先鋒電子（香港）有限公司

香港九龍長沙灣道909號5樓

電話： 852-2848-6488

ã 2012 PIONEER CORPORATION. Tous droits de reproduction et de traduction réservés.

Printed in Thailand

Imprimé en Thaïlande

<QRD3130-A/N> EW

Pioneer DEH-1500UBA User manual

Pioneer DEH-1500UBA User manual

in other languages

Related papers

Other documents