Draw-Tite 75547 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
75547
Type
Installation guide

Draw-Tite 75547

The Draw-Tite 75547 is a weight-carrying hitch for the Honda CR-V. It has a maximum towing capacity of 4,500 pounds and a maximum tongue weight of 675 pounds. The hitch is designed to be easy to install and includes all necessary hardware.

The Draw-Tite 75547 is a versatile hitch that can be used for a variety of purposes, including:

  • Towing trailers
  • Hauling cargo
  • Mounting bike racks
  • Installing other accessories

The hitch is constructed from high-strength steel and is coated with a durable finish to resist corrosion. It is also backed by a limited lifetime warranty.

Draw-Tite 75547

The Draw-Tite 75547 is a weight-carrying hitch for the Honda CR-V. It has a maximum towing capacity of 4,500 pounds and a maximum tongue weight of 675 pounds. The hitch is designed to be easy to install and includes all necessary hardware.

The Draw-Tite 75547 is a versatile hitch that can be used for a variety of purposes, including:

  • Towing trailers
  • Hauling cargo
  • Mounting bike racks
  • Installing other accessories

The hitch is constructed from high-strength steel and is coated with a durable finish to resist corrosion. It is also backed by a limited lifetime warranty.

Installation Instructions
Honda CR-V
Part Numbers:
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 17mm, 11/16
Drill Bits: None
Existing
weldnuts
typical
k
j
© 2007,2011,2016 Cequent Performance Products – Printed in Mexico
Sheet 1 of 3 75547N 4-12-16 Rev. C
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: 75547F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Wiring Access Location:
Form: F205 Rev A 5-6-05
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing
Not For Use With Spring Bars
Weight Carrying
Ball Mount
4500 (2043 Kg) 675 (306 Kg)
75547
87440
44575
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
1. Lower exhaust by removing rubber isolators from muffler hangers. Remove the outside isolator first then the inside isolator.
Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
2. Raise hitch into position.
3. Install M10 fasteners as shown.
4. Install the 3/8 U-Bolt through the vehicle tie down hook and through the tie down hook attachment of the receiver. Install flat
washer, lock washers and 3/8 hex nuts as shown above.
5. Tighten all fasteners to the required torque specification.
6. Raise exhaust back into position and re-install rubber isolators.
Inside isolator
Note:
Fasteners typical both sides
Exhaust shown lower
m
n
o
l
Tie
down
hook
j
Qty. (4) Hex Bolt M10X1.25X30 CL8.8
m
Qty. (2) Flat Washer
k
Qty. (4) Conical Washers
n
Qty. (2) Lock Washer
l
Qty. (1) 3/8-16 U-Bolt
o
Qty. (2) 3/8 Hex Nut
Fascia
Frame rail
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3

Draw-Tite 75547 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
75547
Type
Installation guide

Draw-Tite 75547

The Draw-Tite 75547 is a weight-carrying hitch for the Honda CR-V. It has a maximum towing capacity of 4,500 pounds and a maximum tongue weight of 675 pounds. The hitch is designed to be easy to install and includes all necessary hardware.

The Draw-Tite 75547 is a versatile hitch that can be used for a variety of purposes, including:

  • Towing trailers
  • Hauling cargo
  • Mounting bike racks
  • Installing other accessories

The hitch is constructed from high-strength steel and is coated with a durable finish to resist corrosion. It is also backed by a limited lifetime warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents