D60 Digital Projector
User Manual
2 Table of contents
Table of contents
Important safety instructions.. 3
Overview ................................. 5
Shipping contents........................5
Remote control batteries ...........5
Remote control operation .........5
Projector features........................6
Projector exterior view................7
Controls and functions................8
Front and upper side view ..............8
Remote control ................................9
Positioning your projector....10
Choosing a location .................10
Obtaining a preferred projected
image size...................................11
Shifting the projection lens
vertically..........................................11
How to determine the position of the
projector for a given screen size..12
How to determine the recommend-
ed screen size for a given
distance ..........................................12
Projection dimensions....................13
Connecting with video
equipment............................. 15
Preparations....................................15
Connecting HDMI devices............16
Connecting RGBHV devices.........16
Connecting component-video de-
vices.................................................16
Connecting S-Video or video
devices............................................17
Connecting a computer...............17
Using the projector ............... 18
Turning the projector on...........18
Selecting an input source.........18
Using the menus ........................19
Fine-tuning the image size and
clarity ..........................................19
Securing the projector..............20
Using a security cable lock...........20
Utilizing the password function.....20
Adjusting the projected image22
Adjusting the projection angle ....22
Correcting picture distortion.........22
Using the preset and user
modes.........................................23
Fine-tuning the picture quality.25
Advanced picture quality
controls .......................................26
Selecting the aspect ratio........29
Operating in a high altitude
environment...............................31
Displaying more than one image
source simultaneously...............32
Creating your own startup
screen .........................................33
Personalizing the projector menu
display.........................................33
Turning the power off................34
On-Screen Display (OSD)
menus..........................................35
Additional information ......... 41
Care of the projector................41
Cleaning and replacing the dust
filter..............................................41
Lamp information......................43
Getting to know the lamp hour ...43
Extending lamp life........................43
Timing of replacing the lamp .......44
Replacing the lamp.......................44
Indicators....................................46
Troubleshooting .........................47
Specifications.............................48
Warranty and Copyright
information ............................ 51
Regulation statements.......... 52
3
Important safety instructions
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
1. Please read this user manual before you operate your projector. Keep this manual in a
safe place for future reference.
2. Always place the projector on a level, horizontal surface during operation.
- Do not place the projector on an unstable cart, stand, or table as it may fall and be
damaged;
- Do not place inflammables near the projector;
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more
than 15 degrees front to back.
3. Do not store the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage.
4. Do not place the projector in any of the following environments:
- space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector;
- locations where temperatures may become excessively high, such as the inside of a car
with all windows closed;
- locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector’s lifespan and darkening the screen;
- locations near fire alarms;
- locations with an ambient temperature above 40°C/104°F;
- locations where altitude is higher than 1500 meters/4920 feet above sea level.
5. Do not block the ventilation holes while the projector is on (even in standby mode):
- Do not cover the projector with any item;
- Do not place the projector on a blanket, bedding or any other soft surface.
6. In areas where the mains power supply voltage may fluctuate by ±10 volts, it is
recommended that you connect your projector through a power stabilizer, surge
protector or uninterruptible power supply (UPS) as appropriate to your situation.
7. Do not step on the projector or place any objects upon it.
8. Do not place liquids near or on the projector. Liquids spilled into the projector will void
your warranty. If the projector does become wet, disconnect it from the power point
and call your local service center to have the projector repaired.
9. Do not look straight into the projector lens during operation. It may harm your sight.
10. Do not operate the projector lamp beyond the rated lamp life. Excessive operation of
lamps beyond the rated life could cause a lamp to break on rare occasions.
11. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
12. This projector is capable of displaying inverted images for ceiling mount installation. Use
only qualified ceiling mounting kit for mounting.
13. Never attempt to replace the lamp assembly until the projector has cooled down and is
unplugged from the power supply.
14. When you think service or repair is required, take the projector only to a suitably qualified
technician.
15. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable parts are the lamp, and air filter which have their own removable covers or
access panels. See pages 42 and 44.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
4 Important safety instructions
Notice
Please keep the original packing for possible future shipment. If you need to pack your projector after
use, adjust the projection lens to an appropriate position, put the lens cushion around the lens, and fit the
lens cushion and projector cushion together to prevent damage during transportation.
Moisture condensation
Never operate the projector immediately after moving it from a cold location to a hot
location. When the projector is exposed to such a change in temperature, moisture may
condense on the crucial internal parts. To prevent the projector from possible damage, do
not use the projector for at least 2 hours when there is a sudden change in temperature.
Avoid volatile liquid
Do not use volatile liquids, such as insecticide or some types of cleaner, near the projector.
Do not have rubber or plastic products touching the projector for a long time. They will leave
marks on the finish. If cleaning with a chemically treated cloth, be sure to follow the cleaning
product’s safety instructions.
Disposal
This product contains the following material which is harmful to human bodies and
environment.
• Mercury, which is used in the lamp.
To dispose of used lamps, consult your local environment authorities for regulations.
Ceiling mounting the projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the projector
may fall from the ceiling due to an improper attachment through the use of the wrong
gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your
projector. We recommend that you also purchase a separate Kensington lock compatible
security cable and attach it securely to both the Kensington lock slot on the projector and
the base of the ceiling mount bracket. This will perform the secondary role of restraining the
projector should its attachment to the mounting bracket become loose.
5
Overview
Overview
Shipping contents
The projector is shipped with the cables required for connection to video equipment. Some
of the items may not be available depending on your region of purchase. Please check with
your place of purchase.
Some of the accessories may vary from region to region.
Remote control batteries
1. To open the battery cover, turn the
remote control over to view its back,
push on the finger grip on the cover
and slide it down in the direction of
the arrow as illustrated. The cover will
slide off.
2. Remove any existing batteries (if
necessary) and install two new AAA batteries observing the battery polarities as
indicated in the base of the battery compartment. Positive (+) goes to positive and
negative(-) goes to negative.
3. Refit the cover by aligning it with the case and sliding it back up into position. Stop when
it clicks into place.
Notes on handling batteries
• Do not mix old batteries with new ones, or mix different types of batteries.
• Avoid leaving the remote control and batteries in an excessive heat or humid
environment like the kitchen, bathroom, sauna, sunroom, or in a closed car.
• Dispose of used batteries according to the battery manufacturer’s instructions and local
environment regulations for your region.
• If the remote control will not be used for an extended period of time, remove the
batteries to avoid damage to the control from possible battery leakage.
Remote control operation
• Make sure that there is nothing positioned
between the remote control and the infrared
(IR) sensor on the projector that might
obstruct the IR beam from the remote control
reaching the projector.
• The effective range of the remote control is
up to 8 meters, and at an angle within 60
degrees of the IR beam. Always aim straight
at the projector, however most screens will also reflect the IR beam to the projector.
Projector Power cables Component
Video cable Remote
control Batteries User manual
CD
Quick
start
guide
(EU) (UK) (US)
up to 8m
6 Overview
Projector features
• Full HD compatible
The projector is compatible with Standard Definition TV (SDTV) 480i, 480p, 576i, 576p, and
High Definition TV (HDTV) 720p, 1080i and 1080p formats, with the 1080p format providing
a true 1:1 image reproduction.
• High picture quality
The projector provides excellent picture quality due to its high resolution, excellent home
theater brightness, super high contrast ratio, vivid color and rich gray-scale
reproduction.
• Super-high contrast ratio
This projector utilizes a motorized IRIS control lens to achieve a super-high contrast ratio.
• Vivid color reproduction
This projector features an 7-segment color wheel to produce realistic color depth and
range unattainable with lesser segment color wheels.
• Rich gray-scale
When viewed in a darkened environment, the automatic gamma control provides
excellent gray-scale display which reveals details in shadows and in night or darkened
scenes.
• Extra-low noise operation
This projector's unique cooling system design prevents unnecessary fan noise, and is
rated at less than 28dB in normal mode and a low 25dB when in whisper mode.
• Motorized lens shift
The remote control can be used to adjust vertical lens shift from the comfort of your
armchair.
• Wide variety of inputs and video formats
The projector supports a wide variety of inputs for connection to your video and PC
equipment, including component video, S-Video, and composite video, as well as
HDMI, RGBHD, and an output trigger for connection to automated screen and
environment lighting systems.
• Panamorph lenses compatible
The projector is compatible with Panamorph lenses that allow you to convert 16:9
projectors to 2.35:1 aspect ratio.
7
Overview
Projector exterior view
Front and upper side view
Rear view
Under and side view
Connector panel
See "Connecting with video equipment" on page 15 for connection details.
1. Rear IR sensor
2. Vent (heated air exhaust)
3. Dust filter grill (cool air intake)
4. Front IR sensor
5. Projection lens
6. Connector panel (see below for details)
7. Main AC power switch
8. Power cable socket
9. Adjustable feet
10. Ceiling mounting holes
11. Kensington lock slot
1
2
3
4
5
7
8
6
10
10
9911
12. HDMI ports
13. Component Video inputs (RCA)
support Y/PB/PR or Y/CB/CR video signal
14. Composite Video input (RCA)
15. S-Video input (mini 4-pin DIN)
16. Component video inputs (BNC)
support Y/PB/PR, Y/CB/CR, or RGB video
signal
17. RGB High Definition inputs (BNC)
supports RGBHV video or PC signal
18. 12V DC output terminal
Used to trigger external devices such as
an electric screen or light control, etc.
Consult your dealer for how to connect
these devices.
19. RS-232 port for wired remote control
12 13 14 15
191817
16
8 Overview
Controls and functions
Front and upper side view
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the projected image.
3. POWER indicator light
Lights up or flashes when the projector is operating. See "Indicators" on page 46 for
details.
4. TEMPerature warning light
Lights up or flashes if the projector’s temperature becomes too high. See "Indicators" on
page 46 for details.
5. LAMP indicator light
Lights up or flashes when the projector lamp has developed a problem. See "Indicators"
on page 46 for details.
1
2
3
4
5
9
Overview
Remote control
7. Arrow buttons (Left , Up , Right ,
Down )
Moves the current On-Screen Display (OSD)
menu selection in the direction of the arrow
being pressed when the OSD menu is
activated. See "Using the menus" on
page 19 for details.
Adjusts the motorised vertical lens by
moving the image upwards or downwards
on the screen in relation to the orientation
of the projector. (Up , Down )
Manually corrects distorted pictures
resulting from an angled projection. (Left
, Right )
8. MENU button
Toggles the On-Screen Display (OSD)
menu on and off. See "Using the menus"
on page 19 for details.
9. EXIT button
Goes back to previous OSD menus, exits
and saves any changes made using the
On-Screen Display (OSD) menu. See
"Using the menus" on page 19 for details.
10. Picture quality adjustment buttons
(BRIGHTNESS, COLOR, CONTRAST, TINT):
Displays the setting bars for adjustment of
the appropriate picture quality values. See
"Fine-tuning the picture quality" on page 25
for details.
11. Picture window control buttons (PIP, SIZES,
POSITION, ACTIVE)
Displays the Picture In Picture (PIP) windows,
toggles between the main window and
sub-window with ACTIVE, and adjusts the
size and position of the currently active
window with SIZE and POSITION. See
"Displaying more than one image source
simultaneously" on page 32 for details.
12. LENS button
Displays the setting page for the adjustment
of the motorised vertical Lens shift value.
See "Shifting the projection lens vertically"
on page 11 for details.
13. IRIS button
Displays the setting bar for the adjustment
of the motorised aperture lens IRIS. See
"Adjusting contrast ratio via IRIS" on page 29
for details.
14. LIGHT button
Turns on the remote control backlight for
about 10 seconds. Pressing any other
button while the backlight is on keeps the
backlight on for a further 10 seconds. Press
the button again to turn the backlight off.
1. POWER button
Toggles the projector between standby
and on.
See "Turning the projector on" on page 18
and "Turning the power off" on page 34 for
details.
2. Source selection buttons (COMP1,
COMP2, VIDEO, HDMI, RGB HD, S-VIDEO)
Selects an input source for display. See
"Selecting an input source" on page 18 for
details.
3. Aspect buttons (ANA, 4:3, LB, WIDE, REAL)
Selects the display aspect ratio. See
"Selecting the aspect ratio" on page 29 for
details.
4. PICTURE MODE button
Selects one of the preset program modes.
See "Selecting a picture mode" on page 23
for details.
5. MEMORY buttons (USER 1, USER 2, USER 3,
and DEFAULT)
Restores picture settings saved in USER 1,
USER 2, USER 3, or DEFAULT for the current
input source. See "Setting the User 1/User 2/
User 3 mode" on page 24 for details.
6. ENTER button
Enacts the selected On-Screen Display
(OSD) menu item.
1
2
3
4
5
7
6
9
12
14
8
10
11
13
10 Positioning your projector
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1. Floor in front of screen;
2. Ceiling in front of screen;
3. Floor at rear of screen; or
4. Ceiling at rear of screen.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
*To set the projector position:
1. Press MENU on the remote control and then press / until the System menu is
highlighted.
2. Press / to highlight Projector Position and press / until the correct
position is selected.
1. Floor front:
Select this location with the projector placed
near the floor in front of the screen. This is the
most common way to position the projector
for quick setup and portability.
3. Floor rear:
Select this location with the projector placed
near the floor behind the screen.
Note that a special rear projection screen is
required.
*Set Floor Rear after you turn the projector on.
2. Ceiling Front:
Select this location with the projector
suspended from the ceiling in front of the
screen.
Purchase an appropriate projector ceiling
mounting kit from your dealer to mount your
projector on the ceiling.
*Set Ceiling Front after you turn the projector
on.
4. Ceiling Rear:
Select this location with the projector
suspended from the ceiling behind the
screen.
Note that a special rear projection screen
and a qualified projector ceiling mounting kit
are required for this installation location.
*Set Ceiling Rear after you turn the projector
on.
Language
Splash Screen
My Screen
Projector Position
Auto Off
Sleep Timer
Background Color
Menu Settings
Input Source
System
S-Video
English
SIM2
Auto Source Search
EXIT Back
Disable
Disable
Blue
On
Floor Front
Display Setup
11
Positioning your projector
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
If the projector is mounted on a ceiling, it must be mounted upside-down.
This projector is equipped with a movable lens. See "Shifting the projection lens vertically"
below for details. You can see the diagrams on pages 13 and 14 for the vertical offset values
in the dimension tables that are measured when the lens is shifted fully up or down.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for both
the projected image size and the vertical offset dimension, which are directly proportional to
the projection distance.
We have provided separate tables of dimensions for both 16:9 and 4:3 screen ratios to assist
you in determining the ideal location for your projector. There are two dimensions to
consider, the perpendicular horizontal distance from the center of the screen (projection
distance), and the vertical offset height of the projector from the horizontal edge of the
screen (offset).
Shifting the projection lens vertically
The vertical lens shift control provides flexibility for installing your projector. It allows the
projector to be positioned slightly above or below the top level of the projected images.
The lens shift (offset) is expressed as a percentage of the projected image height. It is
measured as an offset from the projected image's vertical center. The projector is equipped
with + 60% and - 40% vertical lens shift. You can shift the projection lens upwards or
downwards within the allowable range depending on your desired image position.
To adjust the vertical position of the projection lens:
1. Press LENS or / (when the OSD menu is not activated)
on the remote control to display the adjustment page.
(Pressing ENTER in the Color > Lens Shift menu performs the
same function.)
2. To raise the projected image, press on the remote
control.
To lower the projected image, press on the remote
control.
Black Level
Clarity Control
Color Temperature
Color
S-Video
0 IRE
EXIT Back
Normal
Color Temperature User_ Fine
Gamma Selection
Color Management
Brilliant Color
IRIS ENTER
2.4
Lens Shift 0
Lens Shift
EXIT Back
On
Dynamic Black On
Image Display
Center of the lens
Center of the lens
Projector position:
Floor front or floor rear Projector position:
Ceiling front or ceiling rear
(C)
(D)
(C)
(D)
See pages 13 and 14 for the corresponding values of (C) and (D).
12 Positioning your projector
How to determine the position of the projector for a given screen size
1. Determine the aspect ratio of your screen, 16:9 or 4:3.
2. Refer to the table and find the closest match to your screen size in the left columns
labelled "Screen Dimensions". Using this value, look across this row to the right to find the
corresponding average distance from screen value in the column labelled "Average".
This is the projection distance.
3. Decide the exact height of your projector according to the position of your screen and
the adjustable vertical lens shift range.
For example, if you are using an 120-inch, 4:3-aspect-ratio screen, please refer to "4:3
(standard) ratio screen dimension table". The average projection distance is 495 cm.
How to determine the recommended screen size for a given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1. Determine the aspect ratio of your screen, 16:9 or 4:3.
2. Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
3. Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled "Average". Check that your measured distance is
between the min and max distances listed on either side of the average distance value.
4. Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
For example, if you have a 16:9-aspect-ratio screen and your measured projection distance
was 4.5m (450cm), please refer to "16:9 (widescreen) ratio screen dimension table". The
closest match in the "Average" column is 449 cm. Looking across this row shows that an 100-
inch screen is required.
If you place the projector in a different position (to that recommended), you will have to tilt it
down or up to center the image on the screen. In these situations, some image distortion will
occur. Use the Keystone function to correct the distortion. See "Correcting picture distortion"
on page 22 for details.
13
Positioning your projector
Projection dimensions
Refer to "Dimensions" on page 48 for the center of lens dimensions of this projector before
calculating the appropriate position.
Installation for a 16:9 ratio screen
16:9 (widescreen) ratio screen dimension table
* See the pictures of "Shifting the projection lens vertically" on page 11 for the range of (C) and (D)
The above numbers are approximate and may be slightly different from the actual measurements. Only
the recommended screen sizes are listed. If the your screen size is not in the table above, please contact
your dealer for assistance.
Screen Dimensions Projection Distance in cm Offset
Diagonal
(inch) Height
(cm) Width
(cm)
Min distance
(with max
zoom) Average Max distance
(with min
zoom)
Highest lens
position
(cm) (C)*
Lowest lens
position
(cm) (D)*
41 51 91 167 184 201 5 -46
50 62 111 204 225 245 6 -56
60 75 133 245 270 294 7 -67
70 87 155 286 315 343 9 -78
80 100 177 327 360 392 10 -90
90 112 199 367 404 441 11 -101
100 125 221 408 449 490 12 -112
110 137 244 449 494 539 14 -123
120 149 266 490 539 588 15 -134
130 162 288 531 584 637 16 -146
140 174 310 571 629 686 17 -157
150 187 332 612 674 735 19 -168
160 199 354 653 719 784 20 -179
170 212 376 694 764 833 21 -191
180 224 398 735 809 882 22 -202
190 237 421 776 854 931 24 -213
200 249 443 816 898 980 25 -224
250 311 553 1020 1122 1224 31 -280
300 374 664 1224 1347 1469 37 -336
Screen
Height
Floor
Center of the lens
Diagonal
Projection Distance
Floor Installation
Offset
Screen
Height
Projection Distance
Diagonal
Ceiling
Center of the lens
Ceiling Installation
Offset
14 Positioning your projector
Installation for a 4:3 ratio screen
The illustrations and table below are provided for those users who already have 4:3 aspect
ratio screens or intend to purchase 4:3 aspect ratio screens to view 16:9 ratio projected
images.
4:3 (standard) ratio screen dimension table
* See the pictures of "Shifting the projection lens vertically" on page 11 for the range of (C) and (D)
The above numbers are approximate and may be slightly different from the actual measurements. Only
the recommended screen sizes are listed. If the your screen size is not in the table above, please contact
your dealer for assistance.
Projection Distance
Floor
Screen
Image Height
Center of the lens
Diagonal
Floor Installation
Offset Screen
Image Height Projection Distance
Ceiling
Center of the lens
Diagonal
Ceiling Installation
Offset
Screen Dimensions Projection Distance in cm Offset
Diagonal
(inch) Height
(cm) Width
(cm)
Min
distance
(with max
zoom)
Average
Max
distance
(with min
zoom)
Highest
lens
position
(cm) (C)*
Lowest
lens
position
(cm)(D)*
Image
Height
(cm)
41 62 83 154 169 184 5 -42 47
50 76 102 187 206 225 6 -51 57
60 91 122 225 248 270 7 -62 69
70 107 142 262 289 315 8 -72 80
80 122 163 300 330 360 9 -82 91
90 137 183 337 371 405 10 -93 103
100 152 203 375 413 450 11 -103 114
110 168 224 412 454 495 13 -113 126
120 183 244 450 495 539 14 -123 137
130 198 264 487 536 584 15 -134 149
140 213 284 525 577 629 16 -144 160
150 229 305 562 618 674 17 -154 171
160 244 325 599 659 719 18 -165 183
170 259 345 637 701 764 19 -175 194
180 274 366 674 742 809 21 -185 206
190 290 386 712 783 854 22 -195 217
200 305 406 749 824 899 23 -206 229
250 381 508 937 1031 1124 29 -257 286
300 457 610 1124 1237 1349 34 -309 343
15
Connecting with video equipment
Connecting with video equipment
You can connect the projector to any type of video equipment, such as a VCR, DVD player,
digital tuner, cable or satellite decoder, video game console or digital camera. You can also
connect it to a desktop or laptop PC or Apple Macintosh system. However, it has no built-in
speakers and cannot be connected to audio equipment.
The projector can be connected to multiple video equipment at the same time by using
different cables. All you need to do is select the appropriate input for the projector to display.
Best video quality
The best available video connection method is HDMI. HDMI (High-Definition Multimedia
Interface) supports uncompressed video data transmission between compatible devices like
DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and
listening experience.
See "Connecting HDMI devices" on page 16 for how to connect the projector to a HDMI
device.
The RGBHV also provides high video quality that transmits Red, Green, Blue, Horizontal and
Vertical sync signals separately on its own conductor.
See "Connecting RGBHV devices" on page 16 for how to connect the projector to a RGBHV
device.
The next best video signal is Component Video (not to be confused with composite Video).
Digital TV tuner and DVD players output Component Video natively, so if available on your
devices, this should be your connection method of choice in preference to (composite)
Video.
See "Connecting component-video devices" on page 16 for how to connect the projector to
a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting S-Video or video devices" on page 17 for how to connect the projector to
an S-Video or composite Video device.
Preparations
When connecting a signal source to the projector, be sure to:
1. Turn off all equipment before making any connections.
2. Use only the correct type cables for each source with proper type plugs.
3. Ensure that all cable plugs are firmly fitted to the equipment sockets.
Note that all cables shown in the following connection diagrams may not be supplied with the projector
(See "Shipping contents" on page 5 for details). Most cables are commercially available from electronics
stores.
16 Connecting with video equipment
Connecting HDMI devices
You should use an HDMI cable when making connection between the projector and HDMI
devices.
You should also connect the separate audio cable to a suitable audio amplifier.
Connecting RGBHV devices
Use a RGBHV video cable with 5 BNC male connectors for connection. Be sure to match the
corresponding colors between the cables and the terminals.
Connecting component-video devices
Be sure to match the corresponding colors between the cables and the terminals.
The RCA type component video sockets are provided for connection to video output
devices. If you have a BNC type component video cable, you can alternatively connect
through the BNC component video sockets.
You should also connect the separate audio cable to a suitable audio amplifier.
HDMI cable
From audio output
terminals To audio input
terminals
HDMI device: DVD player, digital tuner, etc.
From audio output
terminals To audio input
terminals
AV equipment: DVD player, digital tuner, etc.
BNC cable
AV equipment: DVD player, digital tuner, etc.
From audio output
terminals To audio input
terminals
Component cable or
17
Connecting with video equipment
Connecting S-Video or video devices
You need only connect S-Video or composite Video cable from the same device, never
both at the same time. You should also connect the separate audio cable to a suitable
audio amplifier.
If you have already made a Component Video connection between the projector and the video source
device, you need not connect to this device again using an S-Video or composite Video connection as
this makes an unnecessary second connection of poorer picture quality. You need only connect using a
composite Video connection if both Component Video and S-Video are not supplied on the video
source device (for example, with some analog video cameras).
Connecting a computer
Connect the projector to a computer with a VGA-BNC cable.
If the selected video image is not displayed after the projector is turned on and the correct video source
has been selected, please check that the video source device is turned on and operating correctly. Also
check that the signal cables have been connected correctly.
Many laptops do not turn on their external video ports when connected to a projector. Usually a key
combination like Fn + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol on the laptop. Press Fn and the labeled function key
simultaneously. Refer to your laptop’s documentation to discover your laptop’s key combination.
From audio output
terminals To audio input
terminals
S-Video cable
Video cable
or
VGA-BNC cable
From audio output
terminals To audio input
terminals
Laptop or desktop computer
18 Using the projector
Using the projector
Preparations
1. Plug in and turn all of the connected equipment on.
2. If not already in, plug the supplied power cable into the
AC inlet on the rear of the projector and turn on the power
switch.
3. Plug the power cable into a wall socket and turn the wall
switch on.
Turning the projector on
Follow the steps below.
1. Make sure the Power light is orange after power has been
applied and the main AC power switch is turned on.
2. Press and hold POWER () on the remote control to turn
the projector on.
3. The fans will start operating, and a start-up image displays
on the screen for a few seconds while it warms up.
4. If you are prompted for a password, press the arrow keys to
enter a six digit password. See "Utilizing the password
function" on page 20 for details.
5. "Source Searching..." will be displayed on the screen
before the projector identifies the input signal. This
message will remain on the screen until a valid signal is
detected. See "Selecting an input source" on page 18 for
details.
6. If the horizontal frequency of the input signal exceeds the range of the projector, the
message "Out of Range" will be displayed on the screen. This message will remain on-
screen until you change the input signal to an appropriate source.
Selecting an input source
The projector can be connected to multiple equipment at the
same time. When the projector is first turned on, it will attempt to
reconnect with the input source which was in use when the
projector was last shut down.
To select the video source:
• Using the remote control
Press one of the Source buttons on the remote control. To switch
between HDMI 1 and HDMI 2, press HDMI again.
•Using the OSD menu
1. Press MENU and then press / until the System menu is
highlighted.
2. Press to highlight Input Source and press ENTER. The source
selection bar displays.
3. Press / repeatedly until your desired signal is selected
and press ENTER.
Once detected, the selected source information will display
on the screen for seconds. If there is multiple equipment
connected to the projector, you can go back to the source
selection bar again to search for other signals.
• If you want the projector to automatically search for the
signals, select On in the System > Auto Source Search menu.
The projector will not
respond to further
commands while it is
warming up.
HDMI 1
Video
S-Video
Component 1
Component 2
Language
Splash Screen
My Screen
Projector Position
Auto Off
Sleep Timer
Background Color
Menu Settings
Input Source
System
S-Video
English
SIM2
Auto Source Search
EXIT Back
Disable
Disable
Blue
On
Floor Front
ENTER
RGB HD
HDMI 2
NOTE: When
automatically
searching for an
valid input source,
the projector cycles
through the
available signals
following the
sequence from top
to bottom as the
source selection
bar shows.
Display Setup
19
Using the projector
• If you want to use the PIP function, see "Displaying more than one image source
simultaneously" on page 32 for details.
Using the menus
The projector is equipped with multilingual On-Screen Display (OSD) menus for making
various adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set the OSD menu to your familiar language first.
Fine-tuning the image size and clarity
Picture Mode
Load Settings From
Brightness
Contrast
Tint
Sharpness
Reset Picture Settings
Rename User Mode
Image
+ 2
S-Video
Cinema Mode
EXIT Back
Current input source
Main menu
Sub-menu
Highlight
Press EXIT to the
previous page or to exit.
Status
+ 50
+ 50
+ 50
0
Color
Information Color
1. Press MENU on the remote control to turn the
OSD menu on.
2. Use / to highlight the System menu.
3. Press to highlight Language and
press / to select a preferred
language.
4. Press MENU once or EXIT twice* on
the remote control to leave and save
the settings.
*The first press leads you back to the main
menu and the second press closes the OSD
menu.
Picture Mode
Load Settings From
Brightness
Contrast
Tint
Sharpness
Reset Picture Settings
Rename User Mode
Image
S-Video
Cinema Mode
EXIT Back
Color
+ 2
+ 50
+ 50
+ 50
0
Color
Information
Language
Splash Screen
My Screen
Projector Position
Auto Off
Sleep Timer
Background Color
Menu Settings
Input Source
System
S-Video
English
SIM2
Auto Source Search
EXIT Back
Disable
Disable
Blue
On
Floor Front
Display Setup
Language
Splash Screen
My Screen
Projector Position
Auto Off
Sleep Timer
Background Color
Menu Settings
Input Source
System
S-Video
English
SIM2
Auto Source Search
EXIT Back
Disable
Disable
Blue
On
Floor Front
Display Setup
1. Adjust the projected picture to the size
that you need using the zoom ring. 2. Then sharpen the picture by rotating the
focus ring.
20 Using the projector
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent stealing. If not, purchase a lock,
like Kensington lock, to secure the projector. You can locate a Kensington lock slot on the left
side of the projector. See item 11 on page 7 for details.
A Kensington security cable lock is usually the combination of key(s) and lock. Refer to the
lock’s documentation about how to use it.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. Once the password is set and this function is selected, the projector is password-
protected. Users who do not know the correct password can not use the projector.
You will be inconvenienced if you activate the password functionality and subsequently forget the
password. Print out this manual (if necessary) and write the password you used in this manual, and keep
the manual in a safe place for later recall.
Setting a password
Once a password has been set and activated, the projector cannot be used unless the correct password
is entered every time the projector is started.
1. Press MENU on the remote control and then press / until
the Setup menu is highlighted.
2. Press to highlight Password and press ENTER. The Password
page displays.
3. Highlight Password and press / to select On. The Input
Password page displays.
4. As the picture indicates, the four arrow keys ( , , , )
respectively represent 4 digits (1, 2, 3, 4). According to the
password you desire to set, press the arrow keys on the
remote control to enter six digits for the password.
If the function is used for the first time, enter the default
password (1, 1, 1, 1, 1, 1) of the projector by pressing the
arrow key six times.
Once the password is set, the OSD menu returns to the
Password page.
IMPORTANT: The digits being input will display as asterisks on-
screen. Write your selected password down here in this manual in
advance or right after the password is entered so that it is available
to you should you ever forget it.
Password: __ __ __ __ __ __
5. To leave the OSD menu, press MENU.
If you forget the password
If the password function is activated, you will be asked to enter
the six-digit password every time you turn on the projector. If you
enter the wrong password, the password error message as
pictured to the right displays lasting for three seconds, and the
Input Password page follows. You can retry by entering another
six-digit password, or if you did not record the password in this
manual, and you absolutely do not remember it, you can use the password recall procedure.
See "Entering the password recall procedure" on page 21 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically shut
down in a short time.
Lamp settings
Dust Filter
Pattern
High Altitude Mode
Password
Reset All Settings
Setup
EXIT Back
S-Video
ENTER
Off
Input Password
Password
Password
Change Password
Off
EXIT Clear
EXIT Back
InformationSystem
Password Error
Please try again.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI