DeWalt DXLD113E Operating instructions

Brand: DeWalt

Model: DXLD113E

Type: Operating instructions

HP HT W D HO

Steps Article nr. Weight (Kg) Platform height (mm) Transport length (mm) Breedte onder (mm) Depth base (mm) Height base (mm)

Tolerance / ± 0,25 KG ± 3 mm ± 10 mm ± 5 mm ± 10 mm ± 5 mm

1 x 3 DXLD113E 4,5 750 1540 515 876 1370

1 x 4 DXLD114E 6,0 1000 1810 548 1087 1620

1 x 5 DXLD115E 7,5 1250 2100 581 1280 1870

1 x 6 DXLD116E 9,0 1500 2350 614 1482 2120

1 x 7 DXLD117E 10,0 1750 2620 647 1684 2370

1 x 8 DXLD118E 11,0 2000 2900 680 1886 2620

DeWALT STEP LADDER SINGLE

TECHNICAL DATA SHEET

SINGLE

DEWALT® and the DEWALT Logo are trademarks of Stanley Black & Decker, Inc.

or an afliate thereof and are used under license.

Produced by DAS Ladders Stadsbeemd 1410 - B-3545 - BELGIUM

HP HT W D HO

Steps Article nr. Weight (Kg) Platform height (mm) Transport length (mm) Width base (mm) Depth base (mm) Height open (mm)

Tolerance / ± 0,25 KG ± 3 mm ± 10 mm ± 5 mm ± 10 mm ± 5 mm

2 x 2 DXLD122E 2,5 500 600 485 660 500

2 x 3 DXLD123E 4,3 750 850 518 872 750

2 x 4 DXLD124E 6,0 1000 1130 551 1084 1000

2 x 5 DXLD125E 7,5 1250 1415 584 1296 1250

2 x 6 DXLD126E 9,3 1500 1680 617 1508 1500

2 x 7 DXLD127E 11,0 1750 1960 650 1720 1750

2 x 8 DXLD128E 12,0 2000 2230 683 1932 2000

DOUBLE

OPTIONAL: Fixed support of folding support (available for DT4B and higher)

H0 =

DeWALT STEP LADDER DOUBLE

TECHNICAL DATA SHEET

DEWALT® and the DEWALT Logo are trademarks of Stanley Black & Decker, Inc.

or an afliate thereof and are used under license.

Produced by DAS Ladders Stadsbeemd 1410 - B-3545 - BELGIUM

INSTRUCTIONS FOR USE

1 INSTRUCTIONS FOR USE

The complete user manual can be downloaded from the website www.dewaltladders.be

1.1 Before use

a. Ensure you are sufciently t to use a ladder. Certain medical conditions or medication,

alcohol and drug use can make it unsafe to use a ladder;

b. Ensure that when transporting ladders on roof racks or in a truck, they are properly

secured to avoid any damage;

c. Inspect the ladder following delivery and before rst use, to ensure that all components

are working correctly;

d. Before each job, check that the ladder is not damaged and is safe to use;

e. Professional users must ensure the ladder is regularly inspected;

f. Check that the ladder is suitable for the specic job;

g. Never use a damaged ladder;

h. Remove all dirt from the ladder, such as wet paint, mud, oil or snow;

i. Before using the ladder, a risk assessment must be carried out in accordance with the

legal provisions of the country concerned.

1.2 Placing and erecting the ladder

a. Stand the ladder in the correct position, that is, using the correct angle for a leaning

ladder (approximately 1:4 angle) with the rungs or steps in a horizontal position, or fully

opened if it is a free-standing ladder;

b. Use the ladder’s locking mechanism;

c. The ladder must be placed on level, horizontal and rm ground;

d. The leaning ladder must be placed against an even, rm surface and secured before

use, by tying it or by using a suitable stand-off device for stability;

e. Never move the ladder from the top;

f. When placing the ladder, anticipate the risk of impact, for example from pedestrians,

vehicles or doors. Where possible, close all doors (with the exception of emergency exits)

and windows in the work area;

g. Consider possible electrical hazards in the work area, such as power lines and other

exposed electrical equipment;

h. The ladder must rest on its foot pads, not on the rungs or steps;

i. Ladders must never be placed on slippery surfaces (such as ice, shiny surfaces, or very

dirty surfaces), unless additional effective measures are taken to prevent the ladder from

slipping, or unless dirty surfaces have been sufciently cleaned.

1.3 Using the ladder

a. Never exceed the total maximum load for a particular type of ladder;

b. Do not overreach when working on a ladder, the user must take care that the belt buck-

le (navel) remains within the rails and that both feet are on the same rung/step;

c. Do not step from a leaning ladder on to a higher level without taking additional safety

precautions, such as a rope or a suitable stability device;

d. Do not use free-standing ladders for access to another level;

e. Do not stand on the top three rungs/steps of a leaning ladder;

f. Never stand on the top two rungs/steps of a free-standing ladder, without a platform or

a hand and knee rail;

g. Do not climb higher than the hinge point / hook of the A-position of a free-standing

ladder with an extension ladder at the top. The third part can only be extended for maxi-

mum 1 meter when the ladder is used as free-standing ladder in A-position;

h. Ladders must only be used for light work of short duration;

i. Use a non-conductive ladder for unavoidable live electrical work;

j. Do not use the ladder outdoors in adverse weather conditions, such as strong wind;

k. Never allow children to play on a ladder;

l. Where possible, close all doors (with the exception of emergency exits) and windows in

the work area;

m. Always face the ladder rungs while climbing or descending;

n. Grip the ladder rmly when climbing or descending;

o. Do not use the ladder as a bridge;

p. Wear suitable footwear when climbing a ladder;

q. Avoid excessive lateral load caused by, for example, drilling into brick and concrete;

r. Do not remain on a ladder for a long period of time without taking a regular break

(tiredness is a risk);

s. Leaning ladders that are used for access to a higher level must protrude at least 1 m

above the landing point;

t. Any materials carried while using a ladder must be light and easy to handle;

u. Avoid work that causes a lateral load on free-standing ladders, such as lateral drilling in

hard material (e.g. brick or concrete);

v. Ensure you have sufcient grip while carrying out work on the ladder or take adequate

safety measures if this is not possible.

1.4 Repairs, maintenance and storage

Repairs and maintenance must be carried out by a competent person in accordance with

the manufacturer’s instructions. Store portable ladders and steps in such a way as to pre-

vent sagging. Store portable ladders and steps in a cool ventilated space.

1.5 Additional safety tips when using step ladders/ladders

• Do not wear baggy clothing or jewellery. These may snag when climbing or descending

the step ladder or ladder, resulting in the risk of falling.

• Regularly check that the feet are not worn. Worn feet can cause damage to the ground,

or may cause the step ladder or ladder to slip.

• In the interest of personal safety, only use accessories or tools recommended by DAS

Ladders.

• Never place any tools or other materials at the bottom of the step ladder or ladder as

they can cause you to trip.

• A ladder weighing more than 25 kg must always be carried by two people.

2 CAUSES OF ACCIDENTS

The following (incomplete) list of hazards and their possible causes identies the most

common reasons for accidents when using ladders. This forms the basis of the information

contained in these guidelines.

a. Stability loss:

1. Incorrect positioning of the ladder (e.g. the incorrect angle for a leaning ladder or not ful-

ly opening a free-standing ladder); 2. Slipping on the ground (e.g. the bottom of the ladder

slipping away from the wall);

3. Lateral slipping, lateral falling and toppling (e.g. by overreaching or bad contact surface

at the top);

4. Condition of the ladder (e.g. missing non-slip feet)

5. Stepping from an unsecured ladder at height;

6. Condition of the ground (e.g. unstable, soft ground, sloping ground, slippery surfaces or

dirty, hard surfaces);

7. Bad weather conditions (e.g. wind);

8. Impact to ladder (e.g. vehicle or door);

9. Incorrect choice of ladder (e.g. too short, unsuitable for the job).

b. In handling:

1. Transporting the ladder to the workplace;

2. Setting up and dismantling the ladder;

3. Carrying objects on the ladder.

c. Slipping, tripping, falling:

1. Incorrect footwear;

2. Dirty rungs or steps;

3. Unsafe actions (e.g. climbing two rungs at a time, sliding down the rails).

d. Structural faults to the ladder:

1. Condition of the ladder (e.g. damaged rails, wear);

2. Overloading the ladder.

e. Electrical hazards:

1. Unavoidable work in live environment (e.g. repairing faults);

2. Placing ladders too close to live electrical equipment (e.g. power lines);

3. Ladders that damage electrical material (e.g. housing or protective insulation);

4. Incorrect choice of ladder for electrical work.

APPENDIX A: A1 Informational: This appendix contains examples of safety signs for

the basic manual supplied with each ladder. In these examples, the square safety signs

(sometimes with a green border) denote a positive action to be taken.

max.

150 kg

MAX. 150 kg

OIL

H O

MIN.

1 m

MAX. 1

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

1: Read the instructions

2: Peak load

3: Correct angle

4: Place the ladder on a level ground

5: Do not overreach

6: Ensure the ground is clean

7: Place the ladder on rm ground

8: Ladder length extension above the point at which the ladder provides access

9: Do not step off the ladder from the side

10: Only one person per climbable part of the ladder

11: Carry out a visual inspection before use

12: Do not use the ladder as a bridge

13: Do not stand on the top rung

14: Inspect the ladder’s feet

15: Be aware of electrical hazards when moving the ladder

16: Face the ladder rungs while climbing or descending the ladder

17: Ensure that a free-standing ladder is fully open before use

18: Maximum number of personson the ladder

19: Secure top/bottom of the ladder

20: Ensure the top of the ladder has been placed correctly

21: Ensure the spreader lock is engaged

22: Use the ladder with the correct end facing upwards

23: Do not climb higher than the hinge point / hook of the ladder in A-position.

Third part of ladder can be extended for max.1 meter in A-position..

CONFORMITEITSCERTIFICAAT • CERTIFICAT OF CONFORMITY • CERTIFICAT DE CONFORMITE

LADDERS EN TRAPLADDERS VOOR PROFESSIONEEL GEBRUIK • LADDERS AND STEPLADDERS FOR PROFESSIONAL USE • ECHELLES ET ESCABEAUX POUR USAGE PROFESSIONELLE

EN 131 1/2/3 - WARENWET

Ladders en trapladders van de types:

- DXLD113E - DXLD114E - DXLD115E

- DXLD116E - DXLD117E - DXLD118E

- DXLD122E - DXLD123E - DXLD124E

- DXLD125E - DXLD126E - DXLD127E

- DXLD128E - DXLD2208E - DXLD2210E

- DXLD2212E - DXLD2214E - DXLD2216E

- DXLD2308E - DXLD2310E - DXLD2312E

- DXLD2314E

voldoen aan de normen conform de WARENWET en

EN131.

De veiligheidsvoorschriften zijn onder de vorm van een klever en

handleiding aangebracht op de ladder.

De ladder moet gebruikt worden volgens de veiligheidsvoorschrif-

ten, zoniet valt de verantwoordelijkheid van de fabrikant weg.

Ladders and step ladders types:

- DXLD113E - DXLD114E - DXLD115E

- DXLD116E - DXLD117E - DXLD118E

- DXLD122E - DXLD123E - DXLD124E

- DXLD125E - DXLD126E - DXLD127E

- DXLD128E - DXLD2208E - DXLD2210E

- DXLD2212E - DXLD2214E - DXLD2216E

- DXLD2308E - DXLD2310E - DXLD2312E

- DXLD2314E

comply with the standards as stipulated in the

WARENWET and EN131.

The safety regulations have been affixed to the ladder and step

ladder in the form of a sticky label and manual.

The ladder and step ladder must be used in accordance with

the safety regulations, and if not adhered to, the manufacturer

accepts no liability.

Des échelles et des escabeaux de types:

- DXLD113E - DXLD114E - DXLD115E

- DXLD116E - DXLD117E - DXLD118E

- DXLD122E - DXLD123E - DXLD124E

- DXLD125E - DXLD126E - DXLD127E

- DXLD128E - DXLD2208E - DXLD2210E

- DXLD2212E - DXLD2214E - DXLD2216E

- DXLD2308E - DXLD2310E - DXLD2312E

- DXLD2314E

répondent aux normes conforméments le

WARENWET et EN131.

Les consignes de sécurité sont presentes sur l’échelle et l’esca-

beau sous la forme d’un autocollant et d’un manuel.

L’échelle et l’escabeau doit être utilisée conformément aux con-

signes de sécurité, faute de quoi la résponsabilité du fabricant

est annulée.

DEWALT® and the DEWALT Logo are trademarks of Stanley Black & Decker, Inc. or an afliate thereof and are used under license. Produced by DAS Ladders Stadsbeemd 1410 - B-3545 - BELGIUM

TOM DAS - CEO OF DAS LADDERS BVBA

DeWalt DXLD113E Operating instructions

DeWalt DXLD113E Operating instructions

DeWalt DXLD113E Operating instructions

Related papers

Other documents