Bauhn AS-42LED1 User manual

Bauhn
Brand
Bauhn
Model
AS-42LED1
Category
LCD TVs
Type
User manual
Instruction Manual
Model Number AS-42LED1
After sales support
TEL: 1300 886 649
106cm (42”) FHD 100Hz LED TV
After Sales Support TEL: 1300 886 649
1
What your 2 year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.
In the event of product failure within its intended use over the course of
the rst 2 years after the date of purchase, we will remedy the problem
as quickly as possible once it has been brought to our attention. In the
unlikely event of such an occurrence, or if you require any information
about the product please contact us via our after sales support services,
details of which can be found in this manual and on the product itself.
106cm (42”) FHD 100Hz LED TV
After Sales Support TEL: 1300 886 649
2
What your 2 years warranty means....................................................
Welcome......................................................................................................
Important Safety Instructions...............................................................
Front Panel and Back Panel...................................................................
Antenna/Cable Connection & Quick reference guide.................
Remote Control..........................................................................................
Basic Operation..........................................................................................
FAQ’s..............................................................................................................
Specications.............................................................................................
Base Installation/removal.......................................................................
Contents
1
3
4
5
6
7
9
29
30
31
Pages
After Sales Support TEL: 1300 886 649
3
Congratulations on choosing to buy a BAUHN
®
product. By doing so you now
have the assurance and peace of mind that comes with purchasing a product
made by one of the leading manufacturers. All products brought to you by
BAUHN
®
are manufactured to the highest standards of performance and
safety, and, as part of our philosophy of customer service and satisfaction, are
backed by our comprehensive 2 Year Warranty. We hope you will enjoy using
your purchase for many years to come.
Welcome Section
After Sales Support TEL: 1300 886 649
4
Important Safety Instructions
Read all of the instructions before operating the set. Keep these instructions in a safe place for further use.
• If a television is not positioned in a suciently stable location, it can be potentially hazardous due to
falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:
•Usingcabinetsorstandsrecommendedbythemanufacturerofthetelevision.
•Onlyusingfurniturethatcansafelysupportthetelevision.
•Ensuringthetelevisionisnotoverhangingtheedgeofthesupportingfurniture.
•Notstandingthetelevisionsonclothorothermaterialsplacedbetweenthetelevisionand
supporting furniture.
•Educatingchildrenaboutthedangersofclimbingonfurnituretoreachthetelevisionoritscontrols.
•Notplacingthetelevisionontallfurniture(forexample,cupboardsorbookcases)withoutanchoring
both the furniture and the television to a suitable support.
• The ventilation should not be impede by covering the ventilation openings with items, such as
newspaper, table-cloths, curtains, etc.
• Do not push any objects of any kind into this unit through the cabinet slots as they could touch the
current carrying parts or short-circuit parts, resulting in re, electric shock, or damage to the unit.
• Unplug the set when it is not used for a long period of time.
• Do not dismantle this product by yourself as this may cause damage.
• Do not touch the screen surface with ngers as this may scratch or mark the LCD screen.
• Do not impact the LCD screen with hard pressure as this may damage the LCD screen severely.
• Thebattery(batteryorbatteriesorbatterypack)shallnotbeexposedtoexcessiveheatsuchasdirect
sun, re or the like.
• Please use the core plug as required.
• Unplug the set under the following conditions:
•Ifthesetwillnotbeusedforalongperiodoftime.
•Ifthepowercordorthepoweroutlet/plugisdamaged.
•Ifthesetissubjecttoimpact,hasbeendroppedorisnotworking.
• The mains plug is used as the disconnect device and shall remain readily operable.
• Follow the instructions to install and adjust the product. Adjust those controls that are covered in these
operating instructions as improper adjustment of other controls may result in damage. If this happens,
unplug the set and refer to the service personnel.
• Do not allow anything to rest on or roll over the power cord & signal cable.
• Protect the power cord & signal cable from being trampled or tripped on.
• Do not overload the power cord or power outlet.
• Donotexposethepowercord&signalcabletomoisture.
• Do not install this equipment in a conned space such as a book case or similar unit. To prevent injury,
this apparatus must be securely attached to the wall mount fastened on the wall.
• Place the set on a place that allows good ventilation.
• Do not use the set near damp, and cold areas, protect the set from overheating.
• Keep away from direct sunlight.
• Theapparatusshallnotbeexposedtodrippingorsplashingandnoobjectslledwithliquids,suchas
vases, shall be placed on the apparatus.
• Do not use the set in a dusty area.
• Toreducetheriskofreorelectricshock,donotexposethisappliancetorainormoisture.
• No naked ame sources, such as lit candles, should be placed on the apparatus.
• Dust the set by wiping the screen and cabinet with a soft, clean cloth.
• Donotapplyexcessiveforcetothescreenwhencleaning.
• Do not use water or other chemical cleaner to clean the screen as this may damage the surface of the
LCD screen.
• This appliance is not intended for use by young children or inrm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
After Sales Support TEL: 1300 886 649
5
Front Panel and Back Panel
NOTE: The graphics are for representation only.
1. POWER ON/OFF
2. POWER INDICATOR
3. REMOTE SENSOR
4. PROGRAM UP/DOWN BUTTON
5. VOLUME UP/DOWN BUTTON
6. MENU BUTTON
7. TV/AV BUTTON
8. SPEAKERS
1. VGA INPUT
2. HDMI 3 INPUT
3. HDMI 2 INPUT
4. HDMI 1 INPUT
5. ANTENNA INPUT
6. PC AUDIO
7. YPBPR AUDIO
8. YPBPR INPUT
9. AV INPUT
10. MEDIA/USB INPUT
11. EARPHONE OUTPUT
YPBPR
AUDIO
After Sales Support TEL: 1300 886 649
6
Antenna/Cable Connection
There are two kinds of antenna in use.
NOTE:
1. CurrentoutdoorantennaorcableTVusuallyuse75OHMcoaxialantennacable.Forbetter
reception we suggest using this kind of antenna cable.
2. Flat cable or indoor antenna are an old design, the reception may not be good enough (not
recommended).
QUICK REFERENCE GUIDE
1. After you have connected your TV to the antenna as per above, turn on your TV
via the Remote control.
2. Please select the SOURCE button to ensure you are in the DTV mode.
3. Press the MENU button and select TV.
4. Then select the AUTO TUNE function and press OK.
5. Now select DTV + ATV and press OK.
6. The TV will now tune to all your local channels. At the end of tuning the TV will revert to the rst
logical channel.
For a more detailed SETUP requirements, please select the relevant page in the Instruction
Manual.
After Sales Support TEL: 1300 886 649
7
Remote Control
1
17
2
18
3
19
4
20
5
21
22
23
24
25
26
27
28
29
30
31
6
7
8
9
10
11
12
13
14
15
16
1. STANDBY button
Press to turn the TV on or o (standby).
2. AUTO button
Press to adjust the picture automatically in PC mode.
3. FAV button
Press to select FAV. program one by one.
4. Media button
Press to enter Media/USB mode.
5. Number buttons
Press to enter a channel number.
6. MENU button
Press to display/close the menu.
7. OK button
Presstoconrmandexecutetheselection.
8. DISPLAY button
Press to display status such as zoom,signal source, time
and so on.
9. VOLUME UP/DOWN button
Press to adjust the volume.
10. SOURCE button
Press to display the signal source selection menu.
11. PMODE button
Press to select a dierent picture eect.
12. TEXT/stop button
PresstoenterorexitfromTeletextmode.
13. HOLD button/Freeze
PresstoholdthecurrentTeletextpage.
14. INDEX button
Presstodisplayindexpage.
15. SIZE button
PressthisbuttontoselecttheTeletextsize.
16. Some specially function(see the prompt in the OSD.
17. ASPECT button
Switch to the ZOOM mode.
18. NICAM button
ATV’s NICAM switch.
19. MUTE button
Press to mute or restore the TV sound.
20. TV/RADIO button
Switch the channel between TV and RADIO.
21. REC button
Press to record to PVR.
22. EXIT button
Escape from the current operation.
23. CURSOR button
Direction button for selecting up\down\left or right in
menu mode.
24. EPG button
Electronic program guide.
25. PROGRAM UP/DOWN button
Press to select memorized TV programs.
26. SMODE button
Press to select a dierent sound eect.
27. SLEEP button
Press to select a time period after which the TV will
turn itself o.
28. SUBTITLE button
Press this button to view subtitles if applicable.
29. LANG button
PressthisbuttontoselecttheTeletextlanguage.
30. SUBPAGE button
PressthisbuttontoselecttheTeletextsub-page.
31. REVEAL button
Press to reveal the hidden information.
After Sales Support TEL: 1300 886 649
8
For using the remote control, follow these instructions:
1. Open the back cover of the remote control, then insert two AAA batteries with polarities
matching with the marks inside the battery compartment. Then, close the back cover.
2. Point the remote control towards the infra-red remote sensor on the main unit.
If there is an obstacle between the main unit and remote control, the remote control may not
operate properly.
3. Replace the batteries immediately once the remote control is found not to work properly.
4. Donotmixnewbatterieswitholdones,orbatteriesofdierentbrands.
5. Whenthebatteryisexhausted,electrolyte-leakingmayoccuranddamagetheremotecontrol.
When the operation is not activated, the batteries may be weak, so please replace the batteries.
6. If the remote control is not to be used for a long period of time, please remove the batteries to
avoid electrolyte leaking.
After Sales Support TEL: 1300 886 649
9
Input Source
Press INPUT button to display the input source list;
Press the / button to select the input source you want to watch;
Press the ENTER button to enter the selected input source.
Basic Operation
Press the MUTE button on the remote control, this icon will display on the top-left corner of
the menu. No signal, this
icon will display on the top-left corner of the menu.
Press the MENU button to display the MAIN OSD MENU;
Press the / button to select the menu you want to adjust;
Press the OK button or button to enter the sub menu;
Press the / / / button to select the entry,
then press OK button to enter and press
/ / / to adjust the value of selected entries;
You can press the MENU or EXIT button to save and return back to the previous menu.
After Sales Support TEL: 1300 886 649
10
Video Menu
ATV Source
Press the MENU button on the front of panel or MENU on the remote control to display the main menu.
Press / button to select Video in the main menu, then press the ENTER button or button to enter.
1. Press / / / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press
/ button to adjust or press / button to select.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Brightness
Press / / / button to select Brightness, then press ENTER button to enter and press /
button to adjust.
Contrast
Press / / / button to select Contrast, then press ENTER button to enter and press /
button to adjust.
Saturation
Press / / / button to select Saturation, then press ENTER button to enter and press /
button to adjust.
Sharpness
Press / / / button to select Sharpness, then press ENTER button to enter and press /
button to adjust.
Picture Mode
Press / / / button to select Picture Mode, then press ENTER button to enter and press
/ button to select. (Available picture mode: Custom, Standard, Mild, Vivid). You can press PMODE
button on the remote control to select the Picture Mode directly.
After Sales Support TEL: 1300 886 649
11
Colour Temp
Press / / / button to select Colour Temp, then press ENTER button to enter and press /
button to select. (Available color temp: Cold, Normal, Warm).
NR
Press / / / button to select NR, then press ENTER button to enter and press / button to
select. (Available NR: O, Low, Medium, High).
MPEG NR
Press / / / button to select MPEG NR, then press ENTER button to enter and press /
button to select. (Available MPEG NR: O, Low, Medium, High).
Cinema Mode
Press / / / button to select Cinema Mode, then press ENTER button to enter and press /
button to select.(Available Cinema: O, Low, Medium, High).
Audio Menu
Press the MENU button on the front of the panel or MENU on the remote control to display the
main menu.
Press / button to select Audio in the main menu, then press the ENTER button or button to enter.
1. Press / / / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press / button to adjust or press / button to select.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Volume
Press / / / button to select Volume, then press the ENTER button to enter and press /
button to adjust.
AUDIO
After Sales Support TEL: 1300 886 649
12
Balance
Press / / / button to select Balance, then press the ENTER button to enter and press /
button to adjust.
Treble
Press / / / button to select Treble, then press the ENTER button to enter and press /
button to adjust.
Bass
Press
/ / / button to select Bass, then press the ENTER button to enter and press /
button to adjust.
Equalizer
Press / / / button to select Equalizer, then press the ENTER button to enter. Press /
button to select Rock, Country, Jazz, Classical, Blue, Default, Customer.
AUDIO
After Sales Support TEL: 1300 886 649
13
TV Menu
Press MENU button on the front of panel or MENU on the remote control to display the main menu.
Press / button to select TV in the main menu, then press ENTER button or button to enter.
1. Press / / / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press
/ / / button to edit.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Program Edit
Press / / / button to select Program Table, then
press ENTER button to enter.
Service Type
Press / / / button to select Service Type
(DTV-Radio-All), then press ENTER button to enter and
press ENTER button to adjust.
Network
Press / / / button to select Network, then press ENTER button to enter and press ENTER
button to select All, Network 10, ABC, SBS, Seven, Nine,...
Delete
Press / button to select the channel that you want to delete. Press GREEN button on the remote
control, then press ENTER button to delete.
ONE
ABC
SBS
CH4
After Sales Support TEL: 1300 886 649
14
Move
Press / button to select the channel that you want to move. Press BLUE button on the remote
control, then press / button to select the location you would like to move the channel. Press
ENTER button to move.
FAV
Press / button to select what you want to make a favorite channel, then press button to
select fav and press ENTER button to conrm, press ENTER button again will set it to a normal
channel.
Lock
Press / button to select what you want to lock as a channel, then press button to select lock
and press ENTER button to conrm, press ENTER button again to cancel channel lock.
Skip
Press / button to select what channel you want to skip, then press button to select skip and
press ENTER button to conrm, press ENTER button again to cancel skip channel.
Auto Search
Press / / / button to select Auto Search, then press ENTER button to enter.
Press / button to select ATV, then press ENTER button to start search.
After Sales Support TEL: 1300 886 649
15
Manual Search
Press / / / button to select Manual Search, then press ENTER button to enter.
Channel No.
Press / button to select Channel No., then press / button to adjust.
Color System
Press / button to select Color System, then press / button to select Auto, SECAM, PAL.
Sound System
Press / button to select Sound System, then press / button to select BG, L/L, D/K, I.
AFT
Press / button to select AFT, then press / button to select On or O.
Frequency
Press / button to select Frequency, then press / button to adjust.
Subtitle
After Sales Support TEL: 1300 886 649
16
Press MENU button on the front of panel or MENU on the remote control to display the main menu.
Press / button to select Setup in the main menu, then press ENTER button or button to enter.
1. Press / / / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press / / / button to edit.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Country
Press / / / button to select Country, then press ENTER button to enter and press /
button to select.
OSD Language
Press / / / button to select OSD Language, then press ENTER button to enter and press
/ button to select.
TeletextLanguage
Press / / / buttontoselectTeletextLanguage,thenpressENTERbuttontoenterandpress
/ button to select.
SETUP
AUS
Setup Wizard
Reset
Setup Menu
After Sales Support TEL: 1300 886 649
17
Time Menu
Press MENU button on the front of panel or MENU on the remote control to display the main menu.
Press / button to select Time in the main menu, then press ENTER button or button to enter.
1. Press / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press
/ / / button to edit.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Time Mode
Press / button to select Time Mode, then press ENTER button to enter and press / button to
select Auto or Manual.
Daylight Saving
Press
/ button to select Daylight Saving, then press ENTER button to enter and press /
button to select O or On.
Sleep Time
Press / button to select Sleep Time, then press ENTER button to enter and press / button
to select.
Current Time
Press / button to select Current Time, then
press ENTER button to enter.
Date
Press
/ button to select year, then press
/ button to choose the year of current
time, Chooses the month and the day with the
similar method.
TIME
PVR Schedule
Region ID NSW
After Sales Support TEL: 1300 886 649
18
Time
Press / button to select hour, then press / button to choose the hour of current time,
Chooses the minute with the similar method. Press / button to select AM or PM.
NOTE: Only when you set the Time Mode -- Manual -- you can set the Current Time .
WakeUp Time
Press / button to select WakeUp Time, then press ENTER button to enter. Use the same method
as Current Time to set the date and time.
Others Menu
Press MENU button on the front of panel or MENU on the remote control to display the main menu.
Press / button to select “Others” in the main menu, then press ENTER button or button to enter.
1. Press / button to select the entry that you want to adjust.
2. Press ENTER button to enter and press / / / button to edit.
3. After nishing your adjustment, press MENU or EXIT button to save and return back to the
previous menu.
Personnel Video Recording (PVR)
1 Please insert the Media/USB drive into the Media/USB slot before selecting record mode.
2 Select the TV program and channel you wish to record.
3 Press the REC button twice and input the length of time you wish to record. Press the OK button
and the unit will start recording.
4 If you wish to stop the recording, press the STOP button and then press OK button and the
recording will cease.
5 If you wish to turn the TV OFF during the record mode, press the POWER button on the remote control
and the screen will become black. Once the recording is complete the TV will turn to standby and
power down. During the record time, the LED is BLUE and when it powers down the LED is RED.
NOTE: (A) During the record mode, you cannot change channels or select another function.
(B) If the signal is interrupted or removed while in record, the recording will stop until the
signal is established. This may cause you to lose program content.
6 While in the EPG mode, you can select a scheduled program to start at the program EPG menu time
from the channel list by pressing the BLUE (reminder) button. A symbol of a clock will appear to the
right hand side of the selected program that you wish to record.
NOTE: A OSD message will inform you of the recording of the selected program 30 seconds prior to
the EPG menu scheduled time.
OTHERS
MEDIA
After Sales Support TEL: 1300 886 649
19
Media/USB
Press / / / button to select Media/USB, then
press ENTER button to enter.
Select
Press / / / button to select Select, then press
ENTER button to enter.
More details about Media/USB, please see the Media/
USB source.
Format
Press / / / button to select Format, then press ENTER button to enter.
Press ENTER button to select FAT32, EXT3 or EXT2. After the designation, press / button to
selectOKbutton,willdemonstratethefollowingdialogbox.Press / button to select Yes, then
press ENTER button to format the device, otherwise cancels the formatting. For more information
please refer to Media/USB details.
Screen Mode
Press / / / button to select Screen Mode, then press ENTER button to enter and press /
button to select auto, 16:9 Wide, 16:9 Zoom,16:9 Subtitle, 4:3.
Parental Control
Press / / / button to select Parental Control,
then press ENTER button to enter. Input password to
enter, default password is **8888**.
Parental Lock
Press / / / button to select Parental Lock, then
press ENTER button to enter and press / button to
select O or On. When parental lock is at the **o**
state, does not need to input the password to enter
the parental control menu directly.
Parental Rating
Press / / / button to select Parental Rating, then press ENTER button to enter and press
/ button to select between 3 and 18.
Change PIN
Press / / / button to select Change PIN, then press ENTER button to enter. After inputting
theoldpassword,anewblankpassworddialogueboxwillappear.
Input your new password. After inputting the new password, the screen will show the conrmation
passworddialogbox.Inputyournewpasswordagain.Afterinputtingtheconrmpassword,the
screen will show **Password Changed!**
Blue Screen
Press / / / button to select Blue Screen, then press ENTER button to enter and press /
button to select O or On.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Bauhn AS-42LED1 User manual

Bauhn
Brand
Bauhn
Model
AS-42LED1
Category
LCD TVs
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents