Allen + Roth GCS09084EA User manual

Brand: Allen + Roth

Model: GCS09084EA

Type: User manual

Brown/Gray Egg Chair With Cup Holder

Model Number: GCS09084E/GCS09084EA

THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Assembly Manual

Item Number: 2809212/2809213

Important Safety Information

Please read all instructions carefully before assembling this furniture.

For your safety, assembly by two or more adults is strongly recommended.

Use only vendor-supplied hardware to assemble this item. Using unauthorized

hardware could jeopardize the structural integrity of the item.

Hardware may loosen overtime. Periodically check that all connections are tight.

WARNING-TO AVOID RISK OF FALLING

WEIGHT LIMIT 250 LBS MAXIMUM.

Chair is intended to be used by one person at a time.

Chair and stand must be used with all provided parts. Ensure that all parts are

installed according to instructions and inspected for damage before use.

Ensure that all bolts and hardware are securely tightened and installed before use.

Always inspect your chair, hardware, and stand for damage before use.

Never place infants or pets in the chair.

Never allow young children to use chair without adult supervision.

Do not jump, stand, or twist in chair.

Chair and stand are designed for minimal swing motion. Use care when getting in and

out of chair. If using stand, ensure that chair is facing forward and do not cause chair

to swing outside base area of stand.

Stand must be used with attached covered bungee cord, included with product.

Do not climb on support pole.

Use on even-flat surfaces, not less than 6 ft from any obstruction such as fences,

garage, houses, overhanging branches, laundry lines, or electrical wires.

This hanging egg chair is not a toy.

Before Assembly

Remove all parts and hardware from the box. Place all items on a carpeted or

scratch-free work surface, as this will avoid damaging parts during assembly.

The shipping box provides an ideal work surface.

To avoid accidentally discarding small parts or hardware, do not dispose of any

packaging or contents of the shipping carton until assembly is complete.

Use the parts and hardware lists below to identify and separate each of the

pieces included.

The use of power tools for assembly is not recommended. Power tools can

damage the hardware and/or split the wood.

Note: Do not fully tighten all bolts until all parts are in place. Failure to follow

these instructions may cause the bolts to misalign during assembly.

Care and Cleaning

Dust often and use a vacuum cleaner crevice tool to clean seams.

Do not place furniture in direct sunlight and keep furniture at least 60 cm / 2 ft

from heat sources to avoid fading.

Warranty

This warranty is extended to the original purchaser and applies to defects in

materials and workmanship of your patio furniture provided your furniture is

maintained with care and used only for personal, residential purposes.

Frames are warranted to be free from defects in material or workmanship for a

period of one (1) year.

Cushions, straps and/or wicker weaves are covered for a period of five (5) years

against defects in material or workmanship.

Components

Hardware

(AA) (BB) (CC)

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

........

........................

...........

Qty:2

M8 Nut

Qty:2 Qty:2

.........

........

....................................

Base

Pole Stand

Chair Frame with

Bungee attached

D Seat back cushion

.......... ........1

(DD) (EE) (FF)

(GG)

M8X60 Bolt

M8 Washer

M8 Nut Cap

Qty:2

Spring with

Carabiners

Qty:1

Hex Wrench

Qty:1

Wrench

Qty:1

Step 1

(AA)

Qty: 2

(BB)

Qty: 2

(CC)

(DD) (FF)

(GG)

M8X60 Bolt M8 Washer

M8 Nut

Qty: 2

M8 Nut Cap

Qty: 2

Hex Wrench

Qty: 1

Wrench

Qty: 1

Slide the Pole Stand (B) into the Base (A). Align and insert M8x60 Bolt (AA)

into the corresponding holes. Place Washer (BB) and Nut (CC) onto Bolt (AA) as

shown. Tighten by using Wrench (GG) and Hex Wrench (FF). Once bolts are fully

tightened, place Nut Cap (DD) onto Nut (CC).

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

Step 2

(EE)

Qty: 1

Spring with

Carabiners

Fig.2A

Fig.2B

Fig.2C

Open the locking carabiners by turning the locking bolt. See Fig.2A.

Hang the Spring (EE) to the pole stand (B) using the carabiner, while attaching

the opposite end to the loop on the chair frame (C) as shown in Fig.2B.

Close and lock both top and bottom carabiner as shown in Fig.2C.

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

STEP 3

Make sure you fully tighten the carabiners.

You can use the wrench to tighten the lock.

STEP 4

Open either carabiner on the bottom of the frame and place it

through the ring on the base as shown.

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

STEP 5

Fig.5A

Fig.5B

Re-attach carabiner to strap and lock securely by hand.

STEP 6

Place cushion onto seat and attach it to the frame.

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

NOTICE: Make sure the seat is facing forward in the correct

position as shown before use.

NOTICE: Do Not allow the chair to swing outside of the base area.

If you have any questions or problems, please call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

Allen + Roth GCS09084EA User manual

Allen + Roth GCS09084EA User manual

Allen + Roth GCS09084EA User manual

Related papers

Other documents