IKEA HDN P610 S Program Chart

Brand: IKEA

Model: HDN P610 S

Type: Program Chart

IKEA HDN P610 S is a range hood designed for use in kitchens to extract fumes and odours while cooking. It is designed to be installed either as an extractor version, where fumes are expelled to the outside through a hose, or as a filter version, where air is filtered through a carbon filter and recycled into the surrounding environment.

The hood has a control panel with a light switch and an extraction speed selection switch. It comes equipped with grease filters to trap grease and odours, and a perimeter extraction panel for improved extraction efficiency.

The grease filters should be cleaned regularly using a cloth and a mild detergent, and the perimeter extraction panel should be cleaned as often as the grease filter. The carbon filter, if used, should be replaced every 4 years.

5019 618 33092

LI25PA

User and Maintenance Handbook

Also contains instructions and regulations for safe installation.

Before installing or using the hood, carefully read and follow the instructions given in this

handbook and in the enclosed installation handbook.

Warning! Be sure to observe the minimum installation distance from cookers, which is indicated in

the installation handbook.

If the installation instructions for the gas cooker specify a greater distance, this must be taken into

account.

5019 618 33092

LI25PA

SAFEGUARDING THE ENVIRONMENT

1. Packing

The packing materials are 100% recyclable and are marked with the

recycling symbol . Comply with local regulations for disposal. The

packing materials (plastic bags, polystyrene parts, etc.) are a potential

source of danger and must be kept out of the reach of children.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly scrapped, the user can

help prevent potentially harmful consequences for the environment

and the health of persons.

The symbol on the product or the accompanying documentation

indicates that it should not be treated as domestic waste but must be

taken to a suitable collection centre for the recycling of electrical and

electronic equipment.

Disposal must be carried out in compliance with local regulations on

waste disposal.

For further information on the treatment, recovery and recycling of

this product, contact your competent local office, the household

waste collection service or the shop where you purchased the

appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

IMPORTANT!

• The appliance is not intended for use by children or

persons with limited physical, sensory or mental abilities

or without experience and knowledge of it, unless they

are under the supervision of or instructed in its use by a

person responsible for their safety.

• Children must be supervised so that they do not play with

the appliance.

1. Do not connect the appliance to the mains power supply until

installation has been completed. Always disconnect the hood

before any cleaning or maintenance, by unplugging it or turning

off the main switch in the home.

2. Do not “flambé” food under the hood. Naked flames could

cause a fire.

3. Do not leave pans unattended when frying, since the cooking oil

could catch fire.

4. Regular cleaning and maintenance is essential for correct hood

operation and good performance. Regularly clean all deposits

from dirty surfaces. Regularly remove and clean or change the

filter. Do not use flammable materials to duct the extracted air.

5. If the hood is used together with other appliances operating on

gas or other fuels, the negative pressure in the room must not

exceed 4Pa (4 x 10

-5

bar). Therefore, make sure the room is

adequately ventilated.

6. The air extracted by the hood must not be removed through the

flue of the heating system or other appliances that use gas or

other fuels.

7. The room must be adequately ventilated when the hood is used

together with appliances operating on gas or other fuels.

8. Make sure lamps are cold before touching them.

9. The discharge air must not be ducted in a flue used for removing

fumes produced by appliances operating on gas or other fuels,

but must have a separate outlet. All national regulations on air

discharge must be observed.

10. The hood is not a shelf, therefore do not overload or place

objects on it

Note: always wear work gloves for all installation and maintenance

operations.

Electrical connections

The mains power supply must match the voltage given on the

appliance rating plate located inside the hood. If provided with a

plug, connect the hood to a power socket complying with current

regulations and located in an accessible area. If it does not have a plug

(direct connection to the power supply) or if the socket is not in an

accessible place, fit a suitable double-pole switch that ensures

complete disconnection from the power supply in category III

overvoltage conditions, complying with the installation rules.

IMPORTANT: Before reconnecting the hood circuit to the

power supply and checking correct operation, always make

sure the power cable is correctly fitted and that it was NOT

crushed in its housing during installation.

Cleaning the hood

Warning! Failure to remove oil/grease (at least once a month) could

result in fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

To ensure best use of your hood, please read these instructions

carefully and keep them for future reference.

The packing materials (plastic bags, polystyrene parts, etc.) are a

potential source of danger and must be kept out of the reach of

children.

Make sure the hood was not damaged during transport.

Declaration of conformity

This product has been designed, manufactured and put on the

market in conformity with the following:

- safety objectives of the “Low Voltage” Directive 2006/95/CE

(which replaces 73/23/CEE and subsequent amendments)

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

The hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

The hood is not extracting enough:

• Is the right speed selected?

• Do the filters need cleaning or changing?

• Are the air outlets blocked?

The light does not work:

• Does the lamp need replacing?

• Is the lamp correctly fitted?

AFTER-SALES SERVICE

Before calling the After-Sales Service

1. See if you can eliminate the problem on your own

(see “Troubleshooting guide”).

2. Switch the hood off and then on again to check if the problem

has been eliminated.

3. If the problem persists, contact the After-Sales Service.

Specify:

• the type of problem,

• the product model given on the dataplate inside the hood, visible

on removing the grease filters.

• your full address,

• your telephone number and area code.

• the Service code (the number under the word SERVICE on the

dataplate inside the hood, behind the grease filter).

If any repairs are necessary, contact an authorised Service Centre

(to ensure the use of original spare parts and correct repair).

Failure to comply with these instructions can compromise the safety

and quality of the product.

5019 618 33092

LI25PA

The hood is designed for use in “Extractor version” or in

“Filter version”

Extractor version

(see symbol in installation handbook)

fumes are extracted and expelled to the outside through a

fumes exhaust hose (not supplied) fixed to the collar of the

hood.

In accordance with the exhaust hose purchased, provide a

suitable fixing system to secure it to the collar.

Warning: If already installed, remove the carbon filter/s.

Filter version

(see symbol in installation handbook)

Air is filtered through a carbon filter/s and recycled into the

surrounding environment.

Warning: check that air recirculation is facilitated (to this end,

carefully follow the instructions given in the installation

handbook)

Warning! If the hood does not have a carbon filter/s, order

one/them and fit it/them before use.

The hood comes provided with hardware (e.g.: screws and/or

plugs) suitable for most walls/ceilings. However, it is necessary

to contact a qualified technician to ensure suitability according

to the type of wall/ceiling. The wall/ceiling must be strong

enough to take the weight of the hood.

Very heavy product; hood handling and installation

must be carried out by at least two persons.

5019 618 33092

LI25PA

PRODUCT SHEET

1. Control panel.

2. Perimeter extraction panel

3. Grease filter

4. Light

5. Telescopic flue

Warning! The hood can support a maximum weight of 5 kg

Bulb maintenance

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool to prise

off the lamp cover (Fig.1).

3. Remove the burnt-out bulb.

4. Use G4 20W max halogen bulbs only, taking care not to

touch them with your hands.

5. Close the lighting unit (snap-on).

Perimeter extraction panel maintenance:

Clean the perimeter extraction panel as often as the grease

filter, using a cloth and a not too concentrated liquid

detergent. Never use abrasive substances.

Removing the perimeter extraction panel:

Pull the panel firmly towards you Fig.2.

Warning! Hold the panel with both hands when you remove

it or replace it, to prevent it from falling and causing damage

or injury.

Fitting the perimeter extraction panel:

Refit the panel and secure it using the fastening pins located

on the surface of the hood.

Warning! Always check to ensure that the panel is firmly

fixed in place.

Grease filter maintenance:

1. Disconnect the electrical power supply.

2. Remove the grease filter/s (Fig. 3). To remove, pull

the spring loaded release handle back (f1) then extract the

filter downwards (f2)

Carbon filter maintenance

(only for filtering hood installation models):

Fit a new carbon filter every 4 years

Fitting or renewing the carbon filter (Fig.4):

1. Disconnect the electrical power supply.

2. Remove the grease filters.

3. If the carbon filters are already mounted (two filters covering

the motor protection grille) and need renewing, turn the

central handle anticlockwise until the filters release.

4. If the filters are not already fitted, locate one on each side

to cover both motor protection grilles, then turn the

central handle of the filters clockwise.

5. Refit the grease filters.

CONTROL PANEL

Light switch.

Press the button to switch on the lights.

Extraction speed selection switch.

Press the button to select the extraction speed.

Keep the button pressed for 2 seconds to switch OFF.

Fig. 2

Fig. 1

Fig. 3

Fig. 4

IKEA HDN P610 S Program Chart

IKEA HDN P610 S Program Chart

IKEA HDN P610 S Program Chart

Related papers

Other documents