I.D. Systems N5VMVAC24 User manual

Brand: I.D. Systems

Model: N5VMVAC24

Category: Car alarm

Type: User manual

I.D. Systems N5VMVAC24 is a Motor Vehicle Asset Communicator designed to provide real-time data and insights into vehicle usage and performance. By connecting to the vehicle's OBD port, the device collects and transmits a range of information, including:

Vehicle location and tracking
Engine diagnostics and fault codes
Fuel consumption and efficiency
Driving behavior and performance

With this data, you can gain valuable insights into how your vehicles are being used, identify areas for improvement, and optimize your fleet operations.

Vehicle location and tracking
Engine diagnostics and fault codes
Fuel consumption and efficiency
Driving behavior and performance

With this data, you can gain valuable insights into how your vehicles are being used, identify areas for improvement, and optimize your fleet operations.

Quick Start Guide

Motor Vehicle Asset Communicator™

A RentalFleetTM System Device

123 Tice Blvd • Suite 101 • Woodcliff Lake, NJ 07677 • Phone 201.996.9000 • Fax 201.996.9144 • www.id-systems.com

093-0000076 Rev 02

MVAC

OBD

Connector

Data/Power

Cord

MVAC

Locking

Snap

Clamp Clamp

Lock

MVAC Description

!WARNING: DO NOT UNDER ANY CIRCUMSTANCES MAKE ANY CONNECTIONS TO THE

VEHICLE OTHER THAN THOSE INDICATED IN THE INSTALLATION DOCUMENT

!WARNING: ENSURE THAT THE MVAC IS INSTALLED AS PER THE INSTRUCTIONS PROVIDED

AND IS SECURED AGAINST MOVEMENT DURING OPERATION OF THE VEHICLE

!WARNING: ENSURE THAT THE INSTALLED MVAC CANNOT

INTERFERE WITH THE VEHICLE OPERATOR AT ANY TIME

!WARNING: DO NOT DISCONNECT ANY OF THE VEHICLE’S CABLES

Prior to Installation

Before starting the installation, take a minute to survey the area

underneath and directly behind the dashboard.Select the best

mounting location before you start to work. The harness should be

the appropriate diameter (step 6) and high up behind the

dashboard.

Required Tools

Some tools that may be required for installing the MVAC:

• Portable lighting

• Standard tools for panel removal (if required)

1Insert the key into the ignition and turn the key to the Accessory position so the vehicle will have power.

Locate the vehicle’s OBD port. On most models, the OBD port will be located on either side or underneath

the steering column. On some models, the OBD port may be located behind an access panel. Note: If the

OBD port has plug in it, remove the plug and tape it to the wire harness.

OBD port

Configuring the MVAC Before Installation

Make sure the vehicle’s driver door is open. Plug the MVAC into the vehicle’s OBD connector. Wait for the door

to lock and unlock, and then wait for the LED to turn Green.

If the LED turns Green

Move to step 3

If the LED turns Red, or

does not light up at all

Place this unit to the side and repeat

Step 2 with a different MVAC

WARNING: DO NOT CONNECT THE MVAC TO THE AIRBAG HARNESS (TYPICALLY YELLOW),

OR THE HIGH VOLTAGE WIRE IN HYBRID VEHICLES (TYPICALLY ORANGE).

MVAC Type

Label

WARNING: IT IS CRITICAL TO VERIFY THAT THE MVAC TYPE (TYPE A/TYPE B) MATCHES THE VEHICLE

MODEL IT IS BEING INSTALLED ON. CONSULT THE APPROVED VEHICLES LIST FOR COMPLETE

DETAILS ON WHICH MVAC TYPE IS APPROVED FOR THE VEHICLE MODEL BEING INSTALLED. EACH

MVAC WILL BE MARKED AND LABELED ON THE DATA/POWER CORD.

If the LED blinks or turns

Amber, remove the MVAC

and place it on a

reprogramming station.

This device complies with Part 15 of the FCC and RSS-210 of Industry Canada Rule. Operation is subject to the following two conditions:

(1) This Device may not cause harmful interface, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for digital device, pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following

measures:

1.1. Reorient or relocate the receiving antenna.

1.2. Increase the separation between the equipment and receiver.

1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected.

1.4. Consult the dealer or experienced radio/TV technician for help.

WARNING

Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Find a wire harness for mounting the MVAC within 2 feet

of the OBD port. Once installed, the MVAC must NOT interfere

with the driver’s operation of the vehicle (pedals, steering,

etc.). Make sure the weight of the MVAC will not damage or

pull out the cables from their connectors. If the MVAC is

installed against a vehicle surface (e.g. metal plate), verify

that the I.D. Systems logo is facing against the surface, so

that the clip side is visible and accessable after installation.

Slide back the locking pin

and push back on the

clamp lock to release the

snap clamp.

3/8-inch

actual 3/4-inch

actual

MINIMUM SIZE <--- BUNDLE ---> MAXIMUM SIZE

Push down

Removing the Unit from the Vehicle

(refer to install instructions

for image references)

Electrical ConnecƟons (Cont.)

Motor Vehicle Asset Communicator™

Confidentiality Notice © 2012 I.D. Systems, Inc. All rights reserved. This document contains confidential and/or proprietary information and may be reproduced for internal purposes only. This document may not be

reproduced in part, or shown, or in any way disclosed to any third party, without the express written consent of I.D. Systems, Inc.

Unplug the MVAC from the OBD port.

Remove the the key from the ignition.

When open, the MVAC

will look like this with the

pin out and the clamp released

Slide the pin back

in place to lock the clamp

Tightly clip the MVAC latch around the

cable/wire harness that has a diameter

of ⅜” to ¾”. Make sure the MVAC does

not slide or rub against the wires. If it does,

use a thicker bundle.

6Route the MVAC cord to the OBD port. Wrap the cord

around cables and the OBD port where possible to

ensure it does not interfere with the driver’s operation

of the vehicle. Then plug it into the OBD port.

• Remove key from vehicle

• Unplug MVAC from OBD port

• Put the OBD plug taped to the

MVAC harness back into the OBD

port (if it exists)

• Unwrap MVAC cord as required

• Pull back the locking pin

• Open the mounting latch

• Remove MVAC

• Store MVAC for future use

A RentalFleetTM System Device

093-00000076 Rev 02

NOTE: Secure the MVAC so that it will not cause

rattles, knocks, or vibrations. Carefully avoid

contact or interference with the Park Brake

Mechanism, Steering Knuckles, or any other

moving parts. Avoid areas near heater outlet

vents. If needed, use large nylon cable ties to

mount the MVAC in a safe and secure position.

I.D. Systems N5VMVAC24 User manual

Brand: I.D. Systems

Model: N5VMVAC24

Category: Car alarm

Type: User manual

Vehicle location and tracking
Engine diagnostics and fault codes
Fuel consumption and efficiency
Driving behavior and performance

With this data, you can gain valuable insights into how your vehicles are being used, identify areas for improvement, and optimize your fleet operations.

Download PDF

report

I.D. Systems N5VMVAC24 User manual

I.D. Systems N5VMVAC24 User manual

Other documents