Anolis Ambiane AP User manual

User manual

Ambiane AP (RGBW, RGBA, TD, PW, TW)

The unit generates light by means of high power LEDs. The unit was designed for indoor use only.

1. Attention

 Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall

 nationalandlocalelectricalandconstructioncodesandregulations.

The unit was designed for indoor use only.

AvoidlookingdirectlyintotheLEDlightbeamatcloserange!

 Donotinstalltheunitnearhighlyinammableliquidsormaterials.

Do not allow anything to rest on the unit.

 Donotinstalltheunitnearanopename.

 Donotinstalltheunitindirty,dustyorbadlyventilatedlocation.

 Sucientairaccessingtothehousingoftheunithastobeensured,

there must not be any heat or anti-noise insulation within a 0.6m x 0.6m

 areaaroundtheunit(non-ICratedxture).

ImmunityoftheequipmentisdesignedforelectromagneticenvironmentsE1,E2,E3

 accordingtothestandardEN55103-2ed.2Electromagneticcompatibility.Productfamily

 standardforaudio,video,audiovisualandentertainmentlightingcontrolapparatusfor

 professionaluse.Part2:Immunity.

 Theproduct(coversandcables)mustnotbeexposedtoahighfrequencyelectromagneticeldhigher

 than3V/m.

 Theinstallationcompanyshouldchecklevelsofpossibleinterferencesabovethetestedlevels

 E1,E2,E3givenbythisstandard(e.g.transmittersinsurroundingarea)beforeinstallingtheequipment.

 EmissionoftheequipmentcomplieswiththestandardEN55032Electromagneticcompatibility

 ofmultimediaequipment–EmissionRequirementsaccordingtoclassB.

Suitableforfasteningon   Unsuitableforcoveringbyheatinsulation

 non-ammablesurfacesonly  material

Always switch o power supply of the unit before connecting or disconnecting the unit

2. Installation

1.Prepareacircularopeninginthelowerceiling(1)asshowninthepicturebelow.

2.InserttheAmbianeAPunitintotheopening.FastentheAmbianeAPbymeansoftwospringfasteners(2)

to the opening.

3.ConnectneededcablestotheAmbianeAP.Connectionblocks(4)areplacedonthePCBRB3727(3).The

PCBisunderplasticcover(5)whichisfastenedbymeansoftwoscrews(6).

Theprimarypowerinputservesforastandardpower(e.g.PowerSupplyforAmbianeAP).

Thesecondarypowerinputservesforabackuppower(incasethatprimarypowerfailed).

Ifbothpowerinputsareundervoltage,theprimarypowerhasapriorityandthesecondarypowerisdisabled.

Incaseofprimarypowerloss,thesecondarypowerisenabled.

IftheAmbianeAPissuppliedviathesecondarypower,thelightintensitycanbesetbythetrimmer(9).

TheAmbianeAPcanbecontrolledbyoneofthefollowingmethods:DMX512

DALI

        0-10V(AmbianePW,AmbianeTDonly)

TheAmbianeAPisequippedwithtwoDMXandDALIconnectionblocksforeasyconnectiontoDMXorDALI

chain(In/Outmethod).

DMX connection 0-10V connection Power connection

PCB Function PCB Function PCB Function

0V- Shield    0V 0V    + Power+

D+ Signal(+)   D+ +10V    - Power-

D- Signal(-)

RecommendeddiametersofconductorswithrespecttodistancebetweenAmbianeAPandpowersupplyunit

(AmbianePowerAP).

Distance/cable length 50m 100 m

Diameters of conductors 0.5mm21 mm2

3. DMX and DALI address setting and control

TheDIPswitch(7),locatednexttotheconnectionblocks,allowsyoutorunatestlightandswitchtheAmbiane

APtotheupdatemodeincaseofsoftwareupdate.

DIP10-ifswitchedtoON=testlight(3200KforRGBWandTWversion)

DIP11-selectionofxturecontrol:OFF=DMX512orDALI,ON=0-10V

DIP12-changefromOFFtoONpositionswitchestheAmbianeAPtotheupdatemode(switchingtotheupdate

modeisnotnecessaryiftheRobeUploaderisusedforAmbianeAPupdate).

DMX control

TheDMXstartaddress,istherstchannelusedtoreceiveinstructionsfromtheDMXcontroller.Theaddress

maybeanychannelfrom1to509.DMXaddresscanbeseteitherbyDIPswitchorbyRDM.DMXaddress

setbyRDMoverwritesaddresssetbyDIPswitchandviceversa.ThegreenLED(8)onthePCBsignalsway

ofDMXaddresssetting:

 LEDlights-DMXaddressissetbymeansoftheDIPswitch.

 LEDdoesnotlight-DMXaddressissetbymeansofRDM.

DIP11hastobesetinOFFposition.

ExampleofDMXaddresses:

DALI control

AddressingoftheAmbianeAPismadebymeansofanexternalDALIcontroller.TheexternalDALIcontroller

hastosendactivatingcommand(8=ON)ifyouneedtostartthepermanentcontroloftheAmbianeAP(Ambiane

APwillnotrespondtoDMXcommands)anddeactivatingcommand(0=OFF)tostopcontroloftheAmbianeAP.

DIP11hastobesetinOFFposition.

Note:IfDIP11=OFF(AmbianeAPiscontrolledbyDMXorDALI),therstcomingcommandswitchestheAm-

bianeAPtothecorrespondingoperationmode(DMXoperationbyaDMXcommand,DALIoperationbyaDALI

command).E.g.theAmbianeAPstaysinaDALIoperationandcomingDMXcommandswitchestheAmbiane

APtoDMXoperation.NextcommandisaDALIcommandandswitchestheAmbianeAPtotheDALIoperation

etc.IfyouneedthepermanentDALIoperation,youhavetosendaDALIcommand8totheAmbianeAP.

0-10V control

DIP11hastobesetinONposition.0-10VoperationhasprioritytoDALIcommands.Theoptionisapplicable

forAmbianePWandAmbianeTDonly.

4. RDM

ThisAmbianeAPsupportsRDMoperation.RDM(RemoteDeviceManagement)isabi-directionalcommunica-

tionprotocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512deviceconguration

and status monitoring.

RDMallowsyoutosetsomeoptionsasDMXaddress,selectDMXmodeandreadoutsoftwareversionofthe

AmbianeAPetc.

ViaRDMyoucanalsosetbehaviourofthextureincaseoflossofDMXsignal.Forthispurposeservethe

followingtwooptions:

DMXhold

 ValueOn(0)-thexturekeepslastreceivedDMXvaluesincaseofDMXloss(defaultsetting).

 ValueO(1)-itactivatestheoption"DMXlost".Tosettheoption"DMXhold"toO,youhavetosend

 avalue1viaRDM.

DMXlost

Theoptionisactiveonlyiftheoption"DMXhold"issetO.

 ValueOn(0)-thexturelightsatmax.lightoutputincaseofDMXloss(defaultsetting).

 ValueO(1)-ThelightoutputofthextureisclosedincaseofDMXloss.Tosettheoption"DMXlost"

 toO,youhavetosendavalue1atRDM.

RDMmodelIDfortheAmbianeAPis0x0114.

Parameter ID Discovery command SET command GET command

DISC_UNIQUE_BRANCH *

DISC_MUTE *

DISC_UN_MUTE *

DEVICE_INFO *

SUPPORTED_PARAMETERS *

SOFTWARE_VERSION_LABEL *

DMX_START_ADDRESS * *

IDENTIFY_DEVICE * *

DEVICE_MODEL_DESCRIPTION *

MANUFACTURER_LABEL *

DEVICE_LABEL * *

SENSOR_DEFINITION *

SENSOR_VALUE *

RESET_DEVICE *

DMX_PERSONALITY * *

DMX_PERSONALITY_DESCRIPTION *

SENSOR_VALUE * *

SENSORDEFINITION *

5. Anti-glare ring installation

Inserttheanti-glarering(1)intotheAmbianeAPuntilthreelocks(2)snapintoslots(3).

6. Adapter ring installation

1.Removebothspringfasteners(2)byunscrewingthefourscrewsM4x10(1).

2.Slidetheadapterring(4)ontothehousingoftheAmbianeAP.Screwthenewfasteners(3)onthehousing.

UseoriginalscrewsM4x10(1).

7. DMX protocols

Ambiane RGBW , Ambiane RGBA

Version1.2

Mode 1

Channel

Mode 2

Channe

Mode 3

Channe

Mode 4

Channe

Mode 5

Channe Value Function Type of

control

1 1 1 - 1 0-255

Red

RedLEDssaturationcontrol0%-->100% proportional

- - 2- - 0-255

Red Fine

RedLEDssaturationcontrolfrommin.-->max. proportional

2 2 3 -20-255

Green

GreenLEDssaturationcontrol0%-->100% proportional

- - 4- - 0-255

Green Fine

GreenLEDssaturationcontrolfrommin.-->max. proportional

3 3 5 -30-255

Blue

BlueLEDssaturationcontrol0%-->100% proportional

- - 6 - - 0-255

Blue Fine

BlueLEDssaturationcontrolfrommin.-->max. proportional

4-7-40-255

White/Amber

White(Amber)LEDssaturationcontrol0%-->100% proportional

- - 8- - 0-255

White/Amber Fine

White(Amber)LEDssaturationcontrolmin.-->max. proportional

- - 91 -

1-127

128

129-255

Green White Fine

Uncorrectedwhite

Minusgreen-->uncorrectedwhite

Uncorrectedwhite(128=default)

Uncorrectedwhite-->plusgreen

step

proportional

step

proportional

- - 10 2-

1-10

11-20

21-255

Colour temperature correction (CTC)

Nofunction(default)

Tungstendimming3200K

Tungstendimming(3200K)

Colourtemperaturechanging2700K-6500K

(21=2700K, 64-3200K, 128=4200K, 192-5600K,

255=6500K)

step

proportional

- - 11 3 5 0-255

Dimmer

Lightintensitycoarse0%-->100% proportional

- - 12 - 6 0-255

Dimmer Fine

Lightintensityfrommin.-->max. proportional

Ambiane PW, Ambiane TD

Version1.1

Mode 1

Channel

Mode 2

Channel Value Function Type of control

1 1 0-255

Dimmer

Lightintensitycoarse0%-->100% proportional

-20-255

Dimmer Fine

Lightintensityfrommin.-->max. proportional

Ambiane TW

Version1.3

Mode 1

Channel

Mode 2

Channel

Mode 2

Channel

Mode 2

Channel Value Function Type of

control

1 - 1 - 0-255

White colour selection

Whitefrom2700K-->4000K proportional

- 1 - 1 0-255

Warm White

WarmWhiteLEDssaturationcontrol0%-->100% proportional

-2-20-255

Cool White

CoolWhiteLEDssaturationcontrol0%-->100% proportional

2 3 2 3 0-255

Dimmer coarse

Lightintensitycoarse0%-->100% proportional

- - 3 4 0-255

Dimmer Fine

Lightintensityfrommin.-->max. proportional

8. Technical specications

Inputvoltage:     48VDC

Protectionclass:    CE: (ClassIII)

      ETL:Class2orLVLE

Max.powerconsumption:   50W

Beamangle:     67°,80°withanti-glarering

Colourtemperature:

 AmbianePW    2700K,4000K

 AmbianeTW    2700K-4000K

AmbianeTD    3200K

Control:

 AmbianeRGBW,AmbianeTW  DMX,DALI,RDMcompatible

 AmbianePW,AmbianeTD  DMX,DALI,0-10V,RDMcompatible

DMXchannels:    

 AmbianeRGBW   4(Mode1),3(Mode2),12(Mode3),3(Mode4),6(Mode5)

 AmbianePW,AmbianeTD  1(Mode1),2(Mode2)

 AmbianeTW    2(Mode1),3(Mode2)

TypicalLumenmaintenance:   70%@50,000hours

Ledlifeexpectancy:    minimum50,000hours

Operatingambienttemp.range:  -20°C/+45°C(-4F/+113F)

Operatingtemperature:   75°C@Ambient+35°C(167°F@Ambient+95°F)

Totalheatdissipation:    136BTU/h(calculated)

Cooling:     convection

Housing:     alluminium

Weight:     1.9kg|(4.19lbs)

Installationmethod:    viatwospringfasteners

ICrating:     non-ICrated

Power/DMX/DALIconnection:   terminalblocks

Protectionfactor:    IP20(withoutdiuserglass),IP20/IP54(withDiuserGlass)

AmbianeAPwithoutDiuserGlass   AmbianeAPwithDiuserGlass

9.Included items

1xAmbianeAP

1x Anti-GlareRing(P/N10980386)

1xSetofcableconnectors

1 x User manual

10. Optional Accessories

AmbianePowerAP(P/N10063994)

Anti-GlareRing(P/N10980386)

AdapterRing(235-255mm)(P/N10980388)

11. Dimensions

mm[inch]

12. Maintenance

KeeptheAmbianeAPclean,especiallylightsourceandtheribbedhousing.

13. Software update

SoftwareupdateofthexturecanbedonebymeansoftheROBEUploader.Itisasoftwareforautomatized

softwareupdateofRobeandAnolisxtures.IttakesadvantageofRDMsupport.

Thextureshavetobeconnectedinadaisy-chain(max.32xtures)andvia

the

RobeUniversalInterface/

RobeUniversalInterfaceWTX

andaUSBcableconnectedtothecontrolPCwiththeRobeUploaderrunning.

ThecontrolPCshouldbeconnectedtotheInternet.

Note:

IfyoudothesoftwareupdatebymeansoftheRobeUploader,switchingxturestotheupdatemode(andfrom

theupdatemode)ismadeautomatically,withoutneedtoswitchtheDIP12toONposition(updatemode).

TheRobeUploadersoftwarecannotbeusedifxturesareconnectedbymeansofDALIconnection.

TheRobeUploadersoftwareandusermanualisavailableat:

https://www.robe.cz/robe-uploader/

Version1.8

November22,2021

Specications are subject to change without notice.

Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici