Mircom CNSIS-204 Non-Supervised Signal Isolator Module Owner's manual
- Category
- Fire protection
- Type
- Owner's manual
NON-SUPERVISED SIGNAL ISOLATOR MODULE CNSIS-204
Description
Mircom’s CNSIS-204 Non-Supervised Signal
Isolator Module is designed for installations where
disconnection of, or damage to an in-suite audible
device will not interfere with the ability of audible
devices in other dwelling units, public corridors or
suites to sound on an alarm. The CNSIS-204 mounts
in a 4” square electrical box.
The CNSIS-204 provides four non-supervised
isolator outputs. Under this confi guration, if a short
or open circuit occurs, the isolator disconnects the
audible device from the circuit but it does not indicate
a trouble on the fi re alarm control panel. In this
confi guration, an open circuit in the suite does not
indicate a trouble on the control panel.
Features
Designed for installations where disconnection • of, or damage to an in-suite audible device will
not interfere with the ability of audible devices
in other dwelling units, public corridors or suites
to sound on an alarm
Operates with bells and horns•
Provides 4 non-supervised isolator outputs •
Isolates the in-suite faults but does not indicate • a trouble on the fi re alarm control panel
Mounts in a 4” square electrical box•
Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifi cations and models and also to discontinue models.
Installation Instructions
Mounting of the CNSIS-204 Signal Isolator Module
5224
NOT TO BE USED FOR INSTALLATION PURPOSES.
4" SQUARE ELECTRICAL BOX
2.5" DEEP
FRON T
PLATE
MOUNTING
SCREWS
CNSIS-204
SIGNAL
CIRCUIT ISO LATOR FRON T PLATE
½" PLASTER RING
CHASSIS
GRO UND
WIRE
S5375
CATALOG NUMBER
firealarmresources.com
Canada
25 Interchange Way
Vaughan, Ontario L4K 5W3
Telephone: (905) 660-4655
Fax: (905) 660-4113
Web page: http://www.mircom.com Email: [email protected]
Distributed by:
CAT. 5224
Rev. 6
Typical Wiring Diagram
Typical Wiring of the CNSIS-204 Non-Supervised Signal Isolator Module
Model Description
CNSIS-202 Non-Supervised Signal Isolator Module
Ordering Information
Mircom does not recommend the installation of unsupervised signal circuits. Mircom recommends that
occupants follow proper measures for fi re procedures for their premises.
NOTES:
1. Do not exceed 100mA per suite.
2. For proper system operation refer to detailed installation instructions
provided with control panel and local installation standards.
3. Wiring supervised by the fi re alarm control panel as per code
4. Unsupervised wiring.
5. Refer to the signal device instructions for wiring gauge information.
6. Mircom recommends that all suite isolators should be mounted outside of the suite they are protecting.
NOT TO BE USED FOR INSTALLATION PURPOSES.
U.S.A.
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Toll Free: (888) 660-4655
Fax Toll Free: (888) 660-4113
LISTED FIRE ALARM PANEL
TO NEXT SIGNALLING DEVICE, ISOLAT OR
MODULE, EOL RESISTOR OR RETURN TO
CONTROL PANEL FOR CLASS A WIRING
SIGNALLING DEVICES 100m A MAX. PER SUITE
SUCH BELLS AND HORNS.
SIGNALLING DEVICES 100m A MA X. PER SUITE
SUCH BELLS AND HORNS.
SIGNAL CIRCUIT
SEE NOTE 4
SEE NOTE 4
SEE NOTE 5
ISOLATOR MODULE
CNSIS- 204
ISOLATOR MODULE
CNSIS-204
SUITE 4SUITE 3SUITE 2SUITE 1
SUITE 4 SUITE 3 SUITE 2 SUITE 1
SIG.IN SIG.OUT
S IG.IN S IG.OUT
firealarmresources.com
-
1
-
2
Mircom CNSIS-204 Non-Supervised Signal Isolator Module Owner's manual
- Category
- Fire protection
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI