STIEBEL ELTRON SHC 4 User manual

OPERATION AND INSTALLATION INSTRUCTIONS

FOR THE LICENSED PLUMBER

INSTRUCCIONES DE FUNCIONAMIENTO E INSTALACIÓN

PARA EL PLOMERO MATRICULADO

MODE D’EMPLOI ET DIRECTIVES D’INSTALLATION

INSTALLATION À L’INTENTION DES PLOMBIERS AGRÉÉS

MINI-TANK ELECTRIC WATER HEATERS

CALENTADORES DE AGUA ELÉCTRICOS DE MINI-TANQUE

CHAUFFE-EAU ÉLECTRIQUES À MINI-RÉSERVOIR

» SHC 2.5

» SHC 4

» SHC 6

Conforms to ANSI / UL Std. 174

Certiﬁed to CAN/ CSA Std. C22.2 No. 110

Conforme a ANSI/UL Std. 174

Certiﬁcación con CAN/CSA Std. C22.2 No. 110

Conforme à la norme ANSI/UL Std. 174

Certiﬁé à la norme CAN/CSA Std. C22.2 No. 110

Tested and certiﬁed by WQA to NSF/ANSI372

for lead free compliance.

Probado y certiﬁcado por WQA NSF/ANSI 372 para

el cumplimiento de las regulaciones sin plomo.

Testé et certiﬁé par WQA à la NSF/ANSI 372 pour

une utilisation sans plomb.

2 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM

TABLE OF CONTENTS | OPERATION | INSTALLATION

OPERATION

IMPORTANT SAFETY

INSTRUCTIONS

!

WARNING:

When using electrical appliances, basic safety precau-

tions to reduce the risk of ﬁre, electric shock, or injury

to persons should be followed, including:

1 READ ALL INSTRUCTIONS BEFORE USING THE

WATER HEATER.

2 This water heater must be grounded. Connect

only to properly grounded outlet. See the special

grounding instructions in chapter 9, “Electrical Con-

nection”, pg. 6.

3 Install or locate this water heater only in accordance

with the provided installation instructions.

4 Use this water heater only for its intended use as

described in this manual.

5 Do not use an extension cord with this water heater.

If no receptacle is available adjacent to the water

heater, contact a qualiﬁed electrician to have one

properly installed.

6 As with any appliance, close supervision is neces-

sary when used by children.

7 Do not operate this water heater if it has a damaged

cord or plug, if it is not working properly, or if it has

been damaged or dropped.

8 This water heater should be serviced only by

qualiﬁed service personnel. Contact nearest au-

thorized service facility for examination, repair, or

adjustment.

SAVE THESE INSTRUCTIONS

OPERATION

1. General Information ��3

2. Safety Precautions ��3

3. Register your product ��4

4. General Description ��4

5. Technical Description ��4

6. General Recommendations ��4

INSTALLATION

7. Mounting the Unit �� 5

8. Plumbing Connections ��5

8.1 Filling the Water Heater ________________________________________ 6

9. Electrical Connection ��6

10. Settings ��6

11. Maintenance Instructions ��7

11.1 Descaling the heating element ________________________________ 7

11.2 Venting the T&P relief valve ___________________________________ 7

11.3 Draining the water heater _____________________________________ 7

11.4 Removing the cover _____________________________________________ 7

11.5 Removing the heating element _______________________________ 8

11.6 De-scaling the heating element ______________________________ 8

11.7 Replacing the heating element _______________________________ 8

11.8 Changing the anode rod ________________________________________ 8

11.9 Safety Shut-off ___________________________________________________ 9

12. Technical Data ��9

12.1 Dimensions, SHC 2.5 ___________________________________________ 10

12.2 Dimensions, SHC 4 ______________________________________________ 10

12.3 Dimensions, SHC 6 ______________________________________________ 10

12.4 Wiring diagram _________________________________________________ 10

13. Warranty �� 11

OPERATION

GENERAL INFORMATION

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM SHC 2.5 / SHC 4 / SHC 6 | 3

1. General Information

!

CAUTION:

To reduce the risk of excessive pressures and tem-

peratures in this water heater, install temperature and

pressure protective equipment required by local codes

and no less than a combination temperature and pres-

sure relief valve certiﬁed by a nationally recognized

testing laboratory that maintains periodic inspection

of production of listed equipment or materials, as

meeting the requirements for relief valves and auto-

matic gas shutoff devices for hot water supply sys-

tems, ANSI Z21.22. This valve must be marked with a

maximum set pressure not to exceed the marked max-

imum working pressure of the water heater. Install the

valve into an opening provided and marked for this

purpose in the water heater, and orient it or provide

tubing so that any discharge from the valve exits only

within 6 inches above, or at any distance below, the

structural ﬂoor, and does not contact any live electri-

cal part. The discharge opening must not be blocked

or reduced in size under any circumstances.

Read this entire manual. Failure to follow all the guides, instruc-

tions and rules could cause personal injury or property damage.

Improper installation, adjustment, alteration, service and use of

this unit can result in serious injury.

This unit must be installed by a licensed electrician and plumber.

The installation must comply with all national, state and local

plumbing and electric codes. Proper installation is the responsi-

bility of the installer. Failure to comply with the installation and

operating instructions or improper use voids the warranty.

Save these instructions for future reference. The installer should

leave these instructions with the consumer.

If you have any questions regarding the installation, use or opera-

tion of this water heater, or if you need any additional installation

manuals, please call our technical service line at 800-582-8423

(USA and Canada only). If you are calling from outside the USA

or Canada, please call 413-247-3380 and we will refer you to a

qualiﬁed Stiebel Eltron service representative in your area.

1 Do not locate the water heater where water lines could be

subject to freezing temperatures.

2 It is recommended to have a ﬂoor drain nearby to permit

easy draining of the unit if necessary.

3 Install the water heater so that in the event of a leak, the

resulting ﬂow of water will not cause damage to the area

around the water heater. Under no condition is the manu-

facturer liable for any water damage in connection with this

water heater.

4 When installing the water heater, ensure that clearance

around the unit is provided, for ease of maintenance and

service.

!

This is the safety alert symbol.

It is used to alert you to potential personal injury haz-

ard. Obey all safety messages that follow this symbol

to avoid possible injury or death.

2. Safety Precautions

!

PLEASE READ AND FOLLOW THESE INSTRUCTIONS:

Failure to follow these instructions could result in seri-

ous bodily injury or death.

The unit must be installed by a licensed plumber. The

installation must comply with all national, state and

local plumbing and electric codes.

Service of the unit must be performed by a qualiﬁed

service agency.

Before proceeding with any installation, adjustment,

alteration, or service of this unit the power cord

should be unplugged. Failure to do so could result in

serious personal injury or death.

Never remove the unit‘s cover unless the electricity

servicing the unit is turned off. Failure to do so could

result in personal injury or death.

Do not store or use gasoline or other ﬂammable va-

pors or liquids in the vicinity of this or any other ap-

pliance.

!

DANGER:

Water temperatures over 125 °F (52 °C) can cause

severe burns instantly or death from scalding. A hot

water scalding potential exists if the thermostat on

the unit is set too high. Households with small chil-

dren, disabled or elderly persons may require that the

thermostat be set at 120 °F (49 °C) or lower to prevent

possible injury from hot water.

!

WARNING:

This water heater must be installed strictly in accor-

dance with the instructions enclosed and local electric

and building codes. It is also possible that connections

to the water heater itself may develop leaks. It is

therefore imperative that the water heater be installed

so that any water is directed to an adequate drain in

such a way that water damage to the building, furni-

ture, carpeting or other property cannot occur. Neither

the manufacturer nor the distributor can be held re-

sponsible for damage caused by water from the water

heater, temperature pressure relief valve, or related

ﬁttings where adequate provision to drain such water

has not been provided.

!

CAUTION:

Hydrogen gas can be produced in a hot water system

served by this heater that has not been used for a long

period of time (generally 2 weeks or more). Hydrogen

gas is extremely ﬂammable.

To reduce the risk of injury under these conditions, it

is recommended that the hot water faucet be opened

for several minutes at the kitchen sink before using

any electrical appliance connected to the hot water

system.

When hydrogen is present, there will probably be an

unusual sound such as air escaping through the pipe

as the water begins to ﬂow. There should be no smok-

ing or open ﬂame near the faucet at the time it is open.

Monthly manual venting of the T&P valve will reduce

this effect. See 11.2, “Venting the T&P relief valve”,

pg. 7.

OPERATION

REGISTER YOUR PRODUCT

4 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM

3. Register your product

NOTE:

You must register this product within 90 days of

purchase on our web site in order to activate any

standard warranty or to be eligible for the extended

warranty. Go to our website at:

www.stiebel-eltron-usa.com and click on “Register

Your Product".

Before beginning the registration process, we suggest

that you gather the necessary information as follows:

Model, Example: SHC 2.5 (from the label that is on the

top of the unit in the center)

Number listed after “Nr.”

Place of Purchase

Purchase Date

First & Last Name

Email address

Physical Address

Phone Number

If you have any questions concerning the registration

process or warranty options, please contact Stiebel Eltron

USA directly at (800)-582-8423.

4. General Description

These SHC water heaters can be used in most point-of-use ap-

plications. They are designed to supply hot water for hand wash

and kitchen sinks in a residential, commercial or industrial en-

vironment.

These water heaters can replace traditional hot water systems

which consist of a central hot water heater with hot water piping

going to several draw-off points.

The SHC water heaters are lightweight and compact and manufac-

tured for easy installation. The units are designed to be mounted

on the wall. These units are designed to operate under normal

street water pressure.

5. Technical Description

The pressure vessel of the water heater is welded glass-lined steel

and is equipped with a sacriﬁcial anode rod. The thermal insula-

tion is made of polystyrene.

The water heater is equipped with both a thermostat and a high

limit temperature switch. A temperature/pressure relief valve is

supplied with the unit.

6. General Recommendations

The installation must be carried out by licensed professionals. All

state and local codes must be adhered to.

The manufacturer will not be liable for any damages because of

failure to comply with these installation instructions or because

of improper installation performed by an unqualiﬁed installer.

!

NOTE:

The T&P valve must be manually vented monthly. See

11.2, “Venting the T&P relief valve”, pg. 7.

!

NOTE:

Choose a location that allows easy access for mainte-

nance or servicing.

The water heater should be installed with at least

8˝ (203 mm) of clearance on the top and sides of the

unit.

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM SHC 2.5 / SHC 4 / SHC 6 | 5

INSTALLATION

MOUNTING THE UNIT

INSTALLATION

7. Mounting the Unit

!

NOTICE:

Unit must be installed in a vertical position with the

water ﬁttings pointing upward.

WARNING:

Do not install unit where it would routinely be

splashed with water. Electric shock may result.

CAUTION:

Hot water outlet pipes leaving unit can be hot to the

touch. Insulation must be used for hot water pipes

below a height of 36˝ (.91 m) due to burn risk to chil-

dren.

!

NOTICE:

This unit should not be installed in a location where

it may be exposed to freezing temperatures (less

than 36°F (2°C). If the unit may be subject to freez-

ing temperatures, all water must be drained from the

unit. Failure to comply with this instruction voids all

warranties.

The unit should be located in an area where water

leakage from the unit or connections will not result

in damage to the area adjacent to the unit. If such a

location cannot be avoided it is recommended that a

drain pan be installed under the unit.

1 Drill two ¼ holes in the wall where the water heater will be

mounted.

2 Install plastic wall anchors.

3 Fasten wall mounting bracket to the wall.

4 Hook water heater to the mounting bracket.

5 Pull downwards on the water heater to properly seat it on

the bracket.

8. Plumbing Connections

!

IMPORTANT:

If water pipes are made of copper or bronze, use

dielectric connections to prevent heater corrosion.

Failure to provide dielectric insulation may result in

premature tank or nipple failure and may void your

warranty.

!

IMPORTANT:

In order to avoid water coming in contact with the

male pipe threads, ensure that all thread pitches are

sealed properly. It is especially important that the

ﬁrst thread pitches be fully sealed to ensure no leak-

age will occur after the water connections have been

securely made. Failure to properly seal pipe thread

pitches may allow water to come in contact with the

male threads and create corrosion.

!

NOTICE:

Hard water or water with a high mineral count may

damage the unit. Damage to the unit caused by scale

or a high mineral count is not covered under the war-

ranty.

CAUTION:

To reduce the risk of excessive temperature and

pressure in the water heater, a temperature/pressure

(T&P) relief valve has been installed.

CAUTION:

Always ﬁll the unit’s tank with water before plugging

the water heater’s cord into an electrical outlet. Fail-

ure to do so will result in permanent damage to the

water heater.

!

NOTICE:

When a water heater is installed in a closed water

supply system, such as one having a back-ﬂow pre-

venter in the cold- water supply, means shall be

provided to control thermal expansion. Contact the

water supplier or local plumbing inspector for infor-

mation regarding the control of this situation.

Connect the cold water pipe to the cold water connection on the

unit (blue). Connect the hot water pipe to the hot water connection

on the unit (red).

Ensure that the water heater is installed in a level position.

Install a shut-off on the cold water side of the water heater. This

is for emergency shut-off. It must be kept open when the water

heater is operating.

When using copper piping, solder a piece of tubing to a threaded

ﬁtting (union) before screwing the adapter to the tank.

BRAIDED FLEX HOSE CONNECTORS ARE ALSO RECOMMENDED.

DO NOT APPLY HEAT DIRECTLY TO INLET OR OUTLET CONNECTIONS.

A certiﬁed T&P valve is mounted to the water heater by the manu-

facturer with the outlet oriented to the right. If this position needs

to be changed, leakage may occur, especially if it will be screwed

counter-clockwise, and the T&P valve may need to be resealed.

After all plumbing work has been completed, the T&P valve needs

to be checked for proper tightness.

During heating, the water volume and water pressure increases

in the tank. It is possible for water to leak from the safety valve,

this is normal.

It is recommended to install a check valve on the cold water inlet

supply line to the unit so that air pockets can be purged through

the T&P valve.

6 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

ELECTRICAL CONNECTION

4

3

1

2

1 Temperature/Pressure relief valve

2 Hot water outlet

3 Cold water inlet

4 Discharge pipe

Install a discharge pipe from the relief valve terminating at a sink

or drain. Orient the tubing so that discharge will exit within 6˝

(152 mm) above or at any distance below the structural ﬂoor, and

cannot contact any live electrical parts.

DO NOT CAP OR THREAD THE END OF THE DISCHARGE PIPE, IT

MUST BE UNOBSTRUCTED AND FULL SIZE.

The T&P valve is certiﬁed by a nationally recognized test laboratory

that maintains periodic inspection of the listed equipment, and

meets the requirements for relief valves and automatic shut-off

devices for hot water supply systems ANSI Z21.22.

The T&P valve is marked with a maximum pressure, which does

not exceed the maximum working pressure of the water heater

(150 PSI).

THE DISCHARGE PIPE

- Must not be smaller in size than the outlet pipe size of the

valve, or have reducing couplings.

- Must not be plugged or blocked.

- Must be of material suitable for hot water.

- Must not be over 15

´

(4.5 m) in length.

- Must not have more than two elbows.

- Must terminate at an adequate drain.

- Must not have a valve between the relief valve and the tank.

8.1 Filling the Water Heater

To ﬁll the water heater:

1 Open the hot water faucet.

2 Open the cold water supply valve.

3 When water runs out of the faucet, the tank is ﬁlled.

4 Close the hot water faucet.

5 Manually vent the T&P valve. See 11.2, “Venting the T&P re-

lief valve”, pg. 7.

6 Check entire system for leaks.

9. Electrical Connection

!

CAUTION:

Always ﬁll the unit’s tank with water before plugging

the water heater’s cord into an electrical outlet. Fail-

ure to do so will result in permanent damage to the

water heater.

NOTICE:

The water heater must be connected to a grounded

outlet.

This water heater was designed for use at 110 -

120V. Do not use this water heater with any other

voltage. Failure to use the correct voltage may result

in personal injury or property damage.

The heater is supplied with an electrical cable with a

plug. If the cable is damaged or length not sufﬁcient,

it must be replaced by a licensed electrician.

To be certain that all the air is out of the system, open the hot

water faucet on your ﬁxtures until constant water ﬂows from them.

Otherwise, damage to the device may occur.

Connect the water heater to a GROUNDED OUTLET.

The unit is ﬁtted with a power cord to connect the water heater

to a receptacle. State and local codes must be adhered to. Install

the correct breaker at the circuit breaker panel.

The water heater was manufactured and wired in accordance with

the UL requirements.

A temperature high limit with manual reset has been factory in-

stalled to interrupt the power supply in the event of a thermostat

failure.

DO NOT use this water heater with any other voltage. Failure to

use the correct voltage may result in personal injury or property

damage.

10. Settings

The water heater is equipped with an adjustable thermostat that

automatically controls the water temperature. The indicator lamp

remains lit only when the water is being heated.

The temperature is adjusted by turning the knob counterclockwise

(to the left) to increase the temperature and clockwise (to the right)

to decrease the temperature.

The water heater thermostat can be set to guard against freezing.

This position keeps the internal temperature above the freezing

point.

The piping outside of the water heater and the faucet are not

protected against freezing.

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM SHC 2.5 / SHC 4 / SHC 6 | 7

INSTALLATION

MAINTENANCE INSTRUCTIONS

Freeze protection setting

D0000034989

Temperature setting

The water heater thermostat is factory set at 120°F (49°C).

11. Maintenance Instructions

!

WARNING:

Before servicing or cleaning the water heater, dis-

connect the water heater from the electrical outlet.

The temperature/pressure relief valve must be man-

ually operated once per month. Caution should be

taken to ensure that:

1. No one is near the temperature/pressure relief

valve discharge pipe.

2. The water discharged will not cause any bodily

injury or property damage. The water may be ex-

tremely hot.

Do not attempt to repair the water heater.

Call your licensed plumber or electrician for service. Unplug the

unit whenever the water supply is turned off.

Before calling for service, make sure that:

1 The heater is properly ﬁlled.

2 The electrical supply has not been interrupted.

11.1 Descaling the heating element

Approximately every two years, it is advisable to descale the heat-

ing element and to check the condition of the magnesium anode,

replacing it if the diameter is less than 3/8˝ (10 mm). See 11.8,

“Changing the anode rod”, pg. 8.

11.2 Venting the T&P relief valve

It is recommended to install a check valve on the cold water inlet

supply line to the unit so that air pockets can be purged through

the T&P valve. The temperature/pressure relief valve must be

manually operated once per month. Caution should be taken to

ensure that:

1 No one is near the temperature/pressure relief valve dis-

charge pipe.

2 The water discharged will not cause any bodily injury or

property damage. The water may be extremely hot.

11.2.1 T&P venting / testing procedure

1 Before venting, make sure it is known how to shut off the

water supply to the heater. It is not necessary initially, but

may become so if the T&P valve does not reseat properly

when vented, which may cause water to leak.

2 On the top of the T&P valve is a small handle that lifts a pin in

the center of the valve. Lift the handle up so the valve opens,

then release it so it closes. This will vent the T&P valve and at

the same time test if it is functioning correctly.

3 If the valve is stuck so that it does not open or does not close

it should be replaced immediately.

4 The T&P valve may take more than one attempt to reseat cor-

rectly. If this is the case, try re-opening the valve and quickly

releasing it, allowing it to slap shut. This action does not

damage the valve.

5 If after repeated attempts the valve does not reseat properly

and continues to leak water, it should be replaced. If the

valve fails this test it was already malfunctioning and was not

offering the protection needed.

6 Immediately close the cold water inlet to the heater. Replace

the malfunctioning T&P valve with a new one.

Failure to install and maintain a properly functioning and properly

listed temperature/pressure relief valve will release the manufac-

turer and distributor of this water heater from any claim which

might result from excessive temperature or pressure. Regular

venting/testing may increase the life of the valve.

11.3 Draining the water heater

Some service work requires draining the water heater. This should

be done in the following manner:

1 Unplug the water heater.

2 Open the hot water faucet to let the hot water out. Let it con-

tinue to ﬂow until cold water runs from the faucet.

3 Turn off the cold water supply to the heater.

4 Close the hot water faucet

5 Disconnect the heater from both the hot and cold water

pipes.

6 Carefully detach the water heater from the wall.

7 Tilt the water heater to drain out the remaining water.

11.4 Removing the cover

1 Remove the temperature control knob from the top of the

unit.

2 Remove the screws from the cover.

3 Remove the cover by tilting the bottom side and lifting off the

cover. Cover should come right off.

8 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

MAINTENANCE INSTRUCTIONS

D0000034990

11.5 Removing the heating element

1 Unplug and drain the water heater. See 11.3, “Draining the

water heater”, pg. 7.

2 Remove the cover. See 11.4, “Removing the cover”, pg. 7.

3 Disconnect the line wires from the thermostat.

4 Remove the thermostat from the heating element.

5 Using a suitable wrench, unscrew the heating element.

6 Remove the heating element from the tank.

11.6 De-scaling the heating element

Scale deposit can affect the heating capacity of the heating ele-

ment. Scale can even cause the element to burn out. The element

can be descaled either chemically or manually.

1 Remove the heating element. See 11.5, “Removing the heat-

ing element”, pg. 8.

2 To descale chemically, soak the heating element in white vin-

egar or other descaling solution, then rinse well.

3 To descale manually, use a nonmetallic (soft) tool; brush the

crust off the element. Make sure you do not damage the sur-

face of the heating element.

4 Reinstall the heating element.

5 Reﬁll the water heater with water and check for leaks before

connecting the power.

11.7 Replacing the heating element

1 Unplug and drain the water heater. See 11.3, “Draining the

water heater”, pg. 7.

2 Remove the cover. See 11.4, “Removing the cover”, pg. 7.

3 Remove the heating element. See 11.5, “Removing the heat-

ing element”, pg. 8.

4 Install and seal the new element. Make sure that the heating

element is positioned correctly.

D0000036026

5 Remount all the line wires to their original location.

6 Reﬁll the water heater with water and check for leaks before

connecting the power.

11.8 Changing the anode rod

A magnesium anode is used to extend the life of the tank. Perma-

nent removal of this anode for any reason will void the warranty.

Depending on conditions, the magnesium anode rod may need to

be changed approximately every two years. Galvanic and electro-

lytic corrosion can destroy a tank with a spent anode rod. Rusty

water is usually an indicator of a spent anode rod.

1 Unplug and drain the water heater. See 11.3, “Draining the

water heater”, pg. 7.

2 Remove the cover. See 11.4, “Removing the cover”, pg. 7.

3 Remove the heating element. See 11.5, “Removing the heat-

ing element”, pg. 8.

4 Secure the anode using pliers.

5 Unscrew the nut and remove the anode rod through the

opening of the heating element port.

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM SHC 2.5 / SHC 4 / SHC 6 | 9

INSTALLATION

TECHNICAL DATA

6 Fit a new anode rod including the sealing gasket and sup-

porting washer into the tank opening and secure it with the

included washer and nut. Use a tightening torque of 1100

N•cm ±120 N•cm.

7 Reﬁt all the wires and the heating element.

8 Reﬁll the water heater with water and check for leaks before

connecting the power.

11.9 Safety Shut-off

!

WARNING:

Never lock the sliding reset plunger.

DANGER:

Water temperatures over 125°F (52°C) can cause se-

vere burns instantly or death from scalding. Do not

attempt to reset the high limit switch without ﬁrst

cooling down the water inside the water heater.

11.9.1 Resetting high temperature shut-off system

1 Unplug the water heater.

2 Remove the cover. See 11.4, “Removing the cover”, pg. 7.

3 Unplug the adapter (1) from the controller shaft.

4 Press in button (2) with an appropriate tool.

5 Reassemble the adapter in the correct position.

6 Reassemble the cover of the heater and tighten.

7 Reassemble the thermostat control knob.

1 2

1 Adapter

2 Button

12. Technical Data

SHC 2.5 SHC 4 SHC 6

Item No. 233219 234046 235089

Voltage 110–120 V

Wattage 1300 W

Amperage 11.3 A

Phase Single, 1/N/PE

Frequency 50/60 Hz

Type of installation Under sink

Internal tank material Steel

Enclosure material Plastic

Thermal insulation

material

Polystyrene

Color white

Nominal water volume 2.65 gal / 10 l 4 gal / 15 l 6 gal / 22.7 l

Standby energy loss

1

0.37 kWh/day 0.39 kWh/day 0.47 kWh/day

Recovery time 18 minutes 27 minutes 45 minutes

Temperature setting

range

86–140 °F / 30–60 °C

Max. operating

pressure

150 psi / 1.0 MPa

Weight empty 15.9 lbs / 7.2 kg 19.8 lbs / 9.0 kg 26.2 lbs / 11.9 kg

Weight full 38.6 lbs 17.5 kg 52.9 lbs / 24.0 kg 76.3 lbs / 34.6 kg

Water connections 1/2˝ NPT

1

Measured at 131°F / 55°C set point temperature in 68°F / 20°C ambient air temperature.

10 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

TECHNICAL DATA

12.1 Dimensions, SHC 2.5

i13

c06

c01

3

15

/

16

˝

(100 mm)

10

5

/

8

˝

(270 mm)

3

1

/

8

˝

(80 mm)

11˝

(280 mm)

1

3

/

4

˝

(45 mm)

18

11

/

16

˝

(475 mm)

5

1

/

2

˝

(140 mm)

12

5

/

8

˝

(320 mm)

1

/

16

˝

(26 mm)

12.2 Dimensions, SHC 4

12

5

/

8

˝

(320 mm)

12

1

/

2

˝

(318 mm)

3

1

/

8

˝

(80 mm)

15

/

16

˝

(23 mm)

1

15

/

16

˝

(49 mm)

19

3

/

4

˝

(501 mm)

7

/

8

˝

(200 mm)

13

7

/

16

˝

(342 mm)

c06

c01

i13

3

15

/

16

˝

(100 mm)

12.3 Dimensions, SHC 6

2¼˝

(57 mm)

15

1

/

8

˝

(385 mm)

i13

4⅜˝ (110 mm)

15˝ (380 mm)

1˝

(25 mm)

5½˝

(140 mm)

11

1

/

8

˝

(283 mm)

20½˝

(520 mm)

c06

c01

3

15

/

16

˝

(100 mm)

Label Description Connection

c01 Cold water inlet ½ NPT male

c06 Hot water outlet ½ NPT male

i13 Wall-mounting locations

12.4 Wiring diagram

L

A B

N PE

1 2

D0000035810

4

5

3

2

1

1 Heating element

2 Lamp indicator

3 Cut-off

4 Thermostat

5 Tank

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM SHC 2.5 / SHC 4 / SHC 6 | 11

WARRANTY

Simply the Best

17 West Street

West Hatﬁ eld, MA 01088

TOLL FREE 800.582.8423

PHONE 413.247.3380

FAX 413.247.3369

info

@

stiebel-eltron-usa.com

www.stiebel-eltron-usa.com

MINI-TANK DOMESTIC HOT WATER HEATERS

All SHC Models

LIMITED WARRANTY

Subject to the terms and conditions set forth in this limited

warranty, Stiebel Eltron, Inc. (the “Manufacturer”) hereby

warrants to the original purchaser (the “Owner”) that each

Mini-Tank Domestic Hot Water Heater (the “Heater”) shall

not (i) leak due to defects in the Manufacturer’s materials

or workmanship for a period of six (6) years from the date

of purchase or (ii) fail due to defects in the Manufacturer’s

materials or workmanship for a period of two (2) years

from the date of purchase. As Owner’s sole and exclusive

remedy for breach of the above warranty, Manufacturer

shall, at the Manufacturer’s discretion, send replacement

parts for local repair; retrieve the unit for factory repair, or

replace the defective Heater with a replacement unit with

comparable operating features. Manufacturer’s maximum

liability under all circumstances shall be limited to the

Owner’s purchase price for the Heater.

This limited warranty shall be the exclusive warranty

made by the Manufacturer and is made in lieu of all other

warranties, express or implied, whether written or oral,

including, but not limited to warranties of merchantability

and ﬁ tness for a particular purpose. Manufacturer shall

not be liable for incidental, consequential or contingent

damages or expenses arising directly or indirectly from any

defect in the Heater or the use of the Heater. Manufacturer

shall not be liable for any water damage or other damage

to property of Owner arising, directly or indirectly,

from any defect in the Heater or the use of the Heater.

Manufacturer alone is authorized to make all warranties

on Manufacturer’s behalf and no statement, warranty or

guarantee made by any other party shall be binding on

Manufacturer.

Manufacturer shall not be liable for any damage

whatsoever relating to or caused by:

1. any misuse or neglect of the Heater, any accident to

the Heater, any alteration of the Heater, or any other

unintended use;

2. acts of God and circumstances over which

Manufacturer has no control;

3. installation of the Heater other than as directed by

Manufacturer and other than in accordance with

applicable building codes;

4. failure to maintain the Heater or to operate the Heater

in accordance with the Manufacturer’s speciﬁ cations;

5. operation of the Heater under ﬂ uctuating or excessive

water pressure or in the event the Heater is supplied

with non-potable water, for any duration;

6. improper installation and/or improper materials used

by any installer and not relating to defects in parts or

workmanship of Manufacturer;

7. moving the Heater from its original place of installation;

8. exposure to freezing conditions;

9. water quality issues such as corrosive water, hard water,

and water contaminated with pollutants or additives;

10. not continuously supplying the unit with water aka

“dry-ﬁ ring”.

Should Owner wish to return the Heater to manufacturer

for repair or replacement under this warranty, Owner

must ﬁ rst secure written authorization from Manufacturer.

Owner shall demonstrate proof of purchase, including a

purchase date, and shall be responsible for all removal

and transportation costs. If Owner cannot demonstrate a

purchase date this warranty shall be limited to the period

beginning from the date of manufacture stamped on the

Heater. Manufacturer reserves the right to deny warranty

coverage upon Manufacturer’s examination of the Heater.

This warranty is restricted to the Owner and cannot be

assigned.

Some States and Provinces do not allow the exclusion

or limitation of certain warranties. In such cases, the

limitations set forth herein may not apply to the Owner. In

such cases this warranty shall be limited to the shortest

period and lowest damage amounts allowed by law. This

warranty gives you speciﬁ c legal rights and you may also

have other rights which vary from State to State or Province

to Province.

Owner shall be responsible for all labor and other charges

incurred in the removal or repair of the Heater in the ﬁ eld.

Please also note that the Heater must be installed in such a

manner that if any leak does occur, the ﬂ ow of water from

any leak will not damage the area in which it is installed.

This Warranty is valid for U.S.A. & Canada only. Warranties

may vary by country. Please consult your local Stiebel Eltron

Representative for the Warranty for your country.

13. Warranty

Page is loading ...

34 | SHC 2.5 / SHC 4 / SHC 6 WWW.STIEBEL-ELTRON-USA.COM34 | SHC 2.5 WWW.STIEBEL-ELTRON-USA.COM

NOTES | NOTAS

Www.stiebel-eltron-usa.com SHC 2.5 / SHC 4 | 35

NOTES | NOTAS

Subject to errors and technical changes!

STIEBEL ELTRON, Inc.

17 West Street | West Hatﬁeld MA 01088

Tel. 413-247-3380 | Fax 413-247-3369

[email protected]

www.stiebel-eltron-usa.com

A 304662-39098-9139

4<AMHCMO=aeggcc>

STIEBEL ELTRON SHC 4 User manual

This manual is also suitable for

STIEBEL ELTRON SHC 4 User manual

in other languages

Related papers

Other documents