ProTeam ProGuard 3 Owner's manual

E

N

G

L

I

S

H

OWNER’S MANUAL

Wet/Dry Vacuum

ProGuard

®

LI 3 Cordless

SKU: 107495

Model: 1074950

TABLE OF CONTENTS

ProGuard LI, 3-Gallon Cordless Wet/Dry Vacuum

Important Safety Instructions ...................3

Important Safety Instructions for Battery and Charger ...4

Product Specifications ........................5

Carton Contents ............................5

Preparation For Operation .....................6

Filter Assembly/Replacement ...................7

Hose and Accessory Storage ....................8

Operation ................................9

Battery Installation/Removal...................12

Filter Maintenance .........................13

Preventive Maintenance ......................15

Troubleshooting ........................... 15

ProGuard LI Assembly .......................16

ProGuard LI Replacement Parts ................17

Limited Warranty .......................... 18

Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

French .................................41

Go to www.pro-team.com to register your new vacuum.

E

N

G

L

I

S

H

E

S

P

A

˜

N

O

L

F

R

A

N

Ç

A

I

S

2 ProTeam

INSPECTION

Carefully unpack and inspect your new ProTeam vacuum for shipping

damage. Each unit is tested and thoroughly inspected before shipping.

All returns must have a Return Authorization Number (RAN). To request a

RAN or to ask questions regarding any shipping damage, contact ProTeam

at 866.888.2168 or [email protected].

This Owner’s Manual has important information for the use and safe

operation of this machine. Read this manual carefully before starting

the machine. Keep this manual available at all times and instruct all

operators to read this manual. If instructions are not followed, an injury

may occur, or equipment, furniture, or buildings may become damaged.

For new manuals please contact ProTeam, Inc. at:

[email protected]

8100 W. Florissant Ave., Building T., St. Louis, MO 63136

866.888.2168

or visit www.pro-team.com for a downloadable version.

The contents of this manual are based on the latest product information

available at the time of publication. ProTeam reserves the right to make

changes or improvements to its machines without notice.

ProTeam 3

Safety is a combination of common sense, staying alert, and knowing how your Wet/

Dry vacuum cleaner (“Vacuum”) works.

Safety Signal Words

DANGER: Indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

When using your Vacuum, always follow basic safety precautions including the

following:

WARNING

To reduce the risk of fire, electric shock, or injury:

1. Read and understand this manual and all labels on the Wet/Dry Vacuum before

operating.

2. Use only as described in this manual.

3. Do not leave the Vacuum running while unattended - you may fail to notice

important signs indicating abnormal operation such as loss of suction, debris/

liquid exiting exhaust, or abnormal motor noises. Immediately stop using the

Vacuum if you notice these signs.

4. Use only the batteries specified in this manual. See “Battery Installation”

section.

5. Sparks inside the motor can ignite flammable vapors or dust. To reduce the risk

of fire or explosion, do not use near combustible liquids, gases, or dusts, such as

gasoline or other fuels, lighter fluid, cleaners, oil-based paints, natural gas, coal

dust, magnesium dust, grain dust, aluminum dust, or gun powder.

6. Do not vacuum anything that is burning or smoking, such as cigarettes, matches,

or hot ashes.

7. To reduce the risk of inhaling toxic vapors, do not vacuum or use near toxic or

hazardous materials.

8. To reduce the risk of electric shock, do not expose Vacuum or batteries to rain.

Store indoors.

9. Do not allow to be used as a toy. Close attention is necessary when used by or

near children.

10. Do not use with a torn filter or without the filter installed except when

vacuuming liquids as described in this manual. Dry debris ingested by the

impeller may damage the motor or be exhausted back into the air.

11. Do not handle the switch, Vacuum, or battery with wet hands.

12. Do not put any object into ventilation openings. Do not vacuum with any

ventilation openings blocked; keep free of dust, lint, hair or anything that may

reduce air flow.

13. Keep hair, loose clothing, fingers, and all parts of body away from openings and

moving parts.

14. To reduce the risk of falls, use extra care when cleaning on stairs.

IMPORTANT SAFETY INSTRUCTIONS

!

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY AND CHARGER

VACUUM SAFETY (Continued)

4 ProTeam

15. To reduce the risk of personal injury or damage to Vacuum, use only ProTeam

recommended accessories.

16. When using as a blower:

- Direct air discharge only at work area.

- Do not set down in liquid; electric shock could occur.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except blowing dirt and debris.

- Do not use as a sprayer.

- Wear safety eyewear.

17. To reduce the risk of eye injury, wear safety eyewear. The operation of any

utility Vacuum or blower can result in foreign objects being blown into the eyes,

which can result in severe eye damage.

CAUTION:

• Toreducetheriskofhearingdamage,wearearprotectorswhenusingfor

extended time or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the relative humidity of the air is low. Vacuuming

fine debris with your Vacuum can deposit static charge on the hose or Vacuum.

To reduce the frequency of static shocks or when using this Vacuum, add moisture

to the air with a humidifier.

Observe the following warnings that appear on the Wet/Dry Vacuum:

WARNING:

• Only use ProTeam Battery Number R840087 (107496)

• For your own safety, read and understand Owner’s Manual. Do not

run unattended. Do not pick up hot ashes; coals; toxic, flammable or other

hazardous materials. Do not use around explosive liquids or vapors.

• Do not expose to rain. Store indoors. To reduce the risk of electric shock, do not

handle battery with wet hands or place wet battery into charger.

!

• Readallinstructionsinthecharger’sand

battery’s manuals and on the charger and

battery before using.

• Useonlybatteryspecifiedinthismanual

with this Vacuum.

SAVE THESE INSTRUCTIONS

• Rechargebatteryonlywiththespecified

charger.

• Ensure theswitchis inthe OFF position

before connecting to battery pack,

picking up or carrying the Vacuum.

PROGUARD LI 3 CARTON CONTENTS

OVERVIEW

• 3-GallonCordlessWet/DryVacuum(1)

• Float(2)

• FilterCage(3)

• Filter(4)

• ExpandableHose(5)

• DustingBrush(6)

(1)

(5)

(7)

(8)

(10)

(11)

(6)

(2)

(9)

(3)

(4)

• CreviceTool(7)

• ClawNozzle(8)

• Battery(9)

• Charger(10)

• Owner’sManuals(11)

PRODUCT SPECIFICATIONS

This Wet/Dry Vacuum is shipped with 1 battery and a charger. Additional batteries

or chargers can be purchased from your authorized ProTeam distributor.

Continuous Vacuum Run Time: Approximately 14 minutes per charge

Recharge Time: Approximately 60 minutes

Battery Type: Model No. R840087 (107496)

Battery Technology: Lithium Ion

Battery Charger: Charger Model No. R840093 (107490)

These are typical characteristics based on product testing. You may experience greater or lesser times and

cycles based upon depth of discharge during run period, charging regimen and run period duty cycle.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY AND CHARGER

ProTeam 5

6 ProTeam

PREPARATION FOR OPERATION

GETTING STARTED

This Cordless Wet/Dry Vacuum is intended for commercial use. It may be used for

light vacuuming of wet or dry media and may be used as a blower. The lightweight

and cordless design provides versatility and access to areas where electrical outlets

are not readily available.

Familiarize yourself with the controls and features of your cordless Wet/Dry Vacuum

and read the entire Owner’s Manual for specific usage before operating (Figure A).

Handle

Vacuum

Port Inlet

Accessory

Compartment

Hose

Drum

Latch

Switch

Power

Head

Blower

Port

Figure A

ProTeam 7

FILTER ASSEMBLY/REPLACEMENT

WARNING - To reduce the risk of injury from accidental starting, remove

battery before removing the filter.

1. Grasp the drum latches on both the right and left side of the power head. Slowly

pull the drum latches out and up from the drum. Lift the power head off the

drum. Place the lid assembly of the Vacuum upside down (Figure B).

2. Carefully slide the Qwik Lock™ filter over the filter cage and press down on the

outside edge of the filter until the rubber gasket on the bottom of the filter

seats securely around the base of the filter cage and against the lid (Figure C).

3. Align the small center hole in the top of the filter over the Qwik Lock™ stud on

the filter cage. Press firmly on top of the filter near the stud to allow the filter

to snap over the ball on the end of the stud. The filter is now attached.

NOTE: Failure to properly seat the bottom gasket could result in debris bypassing

the filter.

4. To assemble the power head to the drum, position power head over drum, with

drum latches lined up with recess in drum. (The power head will only fit on the

drum one way.)

5. Position bottom of the latch in drum recess. Push top of latch towards power

head to lock.

6. Your Vacuum is now ready to use. Read the instructions on the following pages

to operate your Vacuum safely.

PULL LATCH OUT

FROM THE TOP

AND UP FROM

THE BOTTOM

Power

Head

Latch (one

on each

side)

Figure B

Filter

Filter Cage

Power

Head

Qwik Lock™ Stud

Figure C

!

8 ProTeam

HOSE AND ACCESSORY STORAGE

1. Your Vacuum’s hose can be conveniently stored as shown in Figure D.

2. Wrap one end of the hose under the handle of the power head and slide into

the hose storage area. Snap the other end of the hose into the inlet port of the

power head.

3. Place the crevice tool into the depressed storage area under the handle.

Crevice

Tool

Handle

Hose

Vacuum

Port

Figure D

ProTeam 9

OPERATION

WARNING - To reduce the risk of fire, explosion, or damage to Vacuum:

• DonotleaveVacuumrunningwhileunattended-youmayfailtonotice

important signs indicating abnormal operation such as loss of suction, debris/

liquid exiting exhaust, or abnormal motor noises. Immediately stop using Vacuum

if you notice these signs.

• UseonlytherecommendedbatterywiththisVacuum.

• Donotcontinuerunningwhenfloathascutoffsuction.

• DonotoperateVacuuminareaswithflammablegases,vapors,orexplosivedust

in the air. Sparks inside the motor can ignite airborne flammables. Flammable

gases and vapors include: lighter fluid, solvent-type cleaners, oil-based paints,

gasoline, alcohol, and aerosol sprays. Flammable dusts include: coal, magnesium,

aluminum, grain, and gun powder.

• Donotvacuumupexplosivedusts,flammableliquids,orhotashes.

• DonotuseVacuumasasprayer.

WARNING - To reduce the risk of electric shock or injury:

• Donotexposetorainorallowliquidtoentermotororbattery

compartment. Store indoors.

• Donothandleswitch,Vacuum,orbatterieswithwethands.

• IfyourVacuumisnotworkingasitshould,hasmissingparts,hasbeendropped,

damaged, left outdoors, or dropped into water, return it to an authorized service

center or call customer service.

• Donotvacuumtoxicmaterialstoreducetheriskofinhalingthevaporsordust.

Turn the unit on by pushing the switch from position “O” to position “l”. The

symbols used on the switch actuator are international “On and Off” symbols (Figure

E).

ON/OFF

Switch

Figure E

=

OFF

=

ON

!

10 ProTeam

OPERATION (Continued)

1. Familiarize yourself with the accessories included with the Vacuum. Each

accessory may be used in various ways for vacuuming and blowing debris. Here is

a list of the accessories and their uses (Figure F).

Crevice Tool - Used to pick up debris in

hard to reach locations.

Dusting Brush - Used for detailed cleaning

in small spaces.

Claw Nozzle - Used to vacuum furniture,

fabric, and upholstery.

Hose - Provides transfer of vacuum or

blowing capability to work site.

Vacuuming Dry Materials

1. The filter must be in correct position

at all times to avoid leaks and possible

damage to Vacuum.

2. When using your Vacuum to pick up

very fine dust, it will be necessary for you to empty the drum and clean the

filter at more frequent intervals to maintain peak Vacuum performance.

NOTE: A dry filter is necessary to pick up dry material. If you use your Vacuum

to pick up dust when the filter is wet, the filter will clog quickly and will be very

difficult to clean.

Vacuuming Liquids

1. When picking up small amounts of liquid the filter may be left in place.

2. When picking up large amounts of liquid we recommend that the filter be

removed. If the filter is not removed, it will become saturated and misting may

appear in the exhaust.

3. When the liquid in the drum reaches a predetermined level, the float mechanism

will rise automatically to cut off airflow. You will know that the float has risen

because Vacuum airflow ceases and the motor noise will become higher in pitch,

due to increased motor speed. When this happens, turn off the Vacuum and

empty the drum.

WARNING - Do not remove the filter cage and float. The float prevents water

from entering the impeller and damaging the motor. The cage prevents fingers

from touching the moving impeller.

4. After using the Vacuum to pick up liquids, the filter must be dried to avoid

possible mildew and damage to the filter.

IMPORTANT: To avoid damage to the Vacuum, do not run motor with float in raised

position.

Hose

Figure F

!

ProTeam 11

Emptying the Dust Drum

Blowing Feature

Your Wet/Dry Vacuum has the capability

to blow sawdust and other debris and to

be used as a blower for yard work, patio

cleanup and workshop applications.

NOTE: The blowing port is located

opposite the vacuum port.

WARNING - Always wear safety

eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before

using as a blower.

WARNING - To reduce the risk of injury to bystanders, keep them clear of

blowing debris.

CAUTION - Wear a dust mask if blowing creates dust which might be inhaled.

(Use N95 or P100 masks when using the vacuum as a blower.)

CAUTION - To reduce the risk of hearing damage, wear ear protectors when

using the Vacuum/Blower for extended time or in a noisy area.

OPERATION (Continued)

Power

Head

Latch (one

on each

side)

PULL LATCH OUT

FROM THE TOP

AND UP FROM

THE BOTTOM

Figure G

Figure H

1. To remove the lid to empty contents

of the dust drum, simply lift the

two drum latches on the side of the

Vacuum and lift the power head up

and off the dust drum and set to the

side (Figure G).

WARNING - To reduce the risk

of injury from accidental starting,

remove battery before emptying the

drum.

2. Lay the power head on a clean dry

area while emptying the drum or

changing the filter.

3. Dump the drum contents into the

proper waste disposal container

(Figure H).

!

12 ProTeam

BATTERY INSTALLATION/REMOVAL

WARNING - Turn unit OFF before

removing/installing the battery.

Installation of Battery

NOTE: ProGuard LI is intended to be

used with only the ProTeam 18V Battery

No. R840087 (107496).

1. While holding the Wet/Dry Vacuum’s

handle with one hand, pull open the

battery compartment cover.

2. Slide the fully charged battery into

the battery receptacle until you hear

an audible click. Do not push the

release buttons on the battery at

this time (Figure I).

Removal of Battery

1. Press both release buttons, located

on each side of the battery, at the

same time and slide battery out of

the battery receptacle (Figure J).

2. Plug charger into a wall receptacle

and place battery into the charger to

recharge the battery (Figure K).

WARNING - To reduce the risk of

electric shock, do not handle battery

with wet hands or place wet battery

into charger.

Battery Pack Preparation for

Recycling

This product contains

a Lithium Ion battery.

Local, state or federal

laws prohibit disposal of

Lithium Ion batteries in

ordinary trash.

Recycling your old

batteries is free and easy with the

Call2Recycle® program. Call2Recycle® is

a product stewardship program providing

no-cost battery and cellphone recycling

solutions across the U.S. and Canada.

Lithium Ion

Battery

Compartment

Cover

S

L

ID

E

Figure I

SLIDE

Battery

Receptacle

Release

Button (2)

Figure J

Lithium Ion

Battery

Charger

Figure K

!

For more information about the Call2Recycle® program, or for more information

about a local collection site visit www.call2recycle.org/locator or call the

Call2Recycle® toll free number 1-800-822-8837.

ProTeam 13

Cleaning Vacuum Filter

WARNING - To reduce the risk

of injury from accidental starting,

disconnect the battery pack from the

Vacuum before changing the filter.

IMPORTANT: After cleaning, check the

filter for tears or small holes. Do not

use a filter with holes or tears in it.

Even a small hole can allow a lot of dust

to pass through the filter. Replace it

immediately.

Filter Removal

1. Hold the filter tabs of the Qwik

Lock™ filter in each hand (Figure L).

2. With one thumb on the Qwik Lock™

stud, which protrudes through the

integrated filter plate, lift up on the

filter tabs while pushing down on

the stud.

3. This action will cause the filter to release from the filter cage. Slide filter off

cage.

IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the

filter before using the Vacuum for dry material pick-up.

WARNING - Do not remove the filter cage and float. The float prevents water

from entering the impeller and damaging the motor. The cage prevents fingers

from touching the moving impeller.

Cleaning a Dry Filter

NOTE: Clean the filter in an open area. Cleaning SHOULD be done outdoors.

1. Light cleaning of some dry debris from the filter can be accomplished without

removing the filter from the Vacuum. Simply slap your hand on top of the handle

while the Vacuum is turned off.

2. Remove filter from Vacuum. Gently tap the filter against the inside wall of your

dust drum and the debris will loosen and fall.

3. For thorough cleaning of a dry filter with fine dust (no debris) you may run water

through it as described under “Cleaning a Wet Filter” Section.

Cleaning a Wet Filter

After filter is removed, run water run water from a hose or spigot through the filter.

Take care that water pressure from the hose is not strong enough to damage filter.

Be sure to air dry the filter before storing or picking up dry debris.

Installation

MAINTENANCE

Filter Cage

Power

Head

Qwik Lock™ Stud

PUSH

DOWN

PULL

UP

Filter Tabs (2)

Integrated Filter

Plate with

Center Hole

Figure L

!

14 ProTeam

Refer to “Filter Assembly/Replacement”

Section of this manual.

Allow the filter to dry before reinstalling

and storing the Vacuum.

Cleaning and Disinfecting the

Wet/Dry Vacuum

To keep your Wet/Dry Vacuum looking

its best, clean the outside with a cloth

dampened with warm water and mild

soap (Figure M).

To clean the drum:

1. Dump out debris.

2. Wash drum thoroughly with warm

water and mild soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed (e.g., waste water pick up) the drum should

be disinfected.

To disinfect the drum:

1. Pour 1 gallon of water and 1 teaspoon of chlorine bleach into the drum.

2. Let solution stand for 20 minutes, carefully swishing every few minutes, making

sure to wet all inside surfaces of the drum.

3. Empty drum after 20 minutes. Rinse with water until bleach smell is gone. Allow

drum to dry completely before sealing the motor on the drum.

WARNING - To assure product SAFETY and RELIABILITY, repairs and adjustments

should be performed by Authorized Service Centers, always using ProTeam

replacement parts.

MAINTENANCE (Continued)

Dampened

Cloth

Vacuum

Assembly

Figure M

!

ProTeam 15

PREVENTIVE MAINTENANCE

TROUBLESHOOTING

WARNING:

The following information is for use by qualified service personnel only and

provides guidance for troubleshooting and maintenance.

• DONOT lubricate the motor.

CARING FOR YOUR VACUUM

1. To ensure a valid vacuum warranty, optimal performance and improved indoor

air quality, be sure to use genuine ProTeam Filters.

2. Check all filters before each use. Empty or replace the filters as necessary.

3. Rinse, air dry, and reinsert the foam/filter diffuser each week.

4. Wipe the inside and outside of the vacuum with a household cleaning agent after

each use.

PROPER STORAGE

When the Vacuum is not in use, the Vacuum, charger, and battery should be stored

indoors and in a dry place. Before storing your Vacuum, the drum should be emptied

and cleaned. The hose should be stored as described in this manual. Accessories should

be kept in the same area as the Vacuum so they can be readily available. The Vacuum

should be stored indoors to avoid temperature extremes that may shorten the useful

life of the battery. Disconnect the battery pack from the Vacuum before storing.

Such preventive safety measures reduce the risk of starting accidentally.

!

1. If the Vacuum will not operate, check the following:

a. That the switch is in the “on” position and functioning properly.

b. Ensure the battery is properly connected to the Vacuum.

c. Ensure the battery is charged.

2. If loss of suction occurs, check the following:

a. Check that debris is not plugging the hose, wand, and/or floor tool.

b. Check and/or clean the filter.

c. Check that the hose cuffs fit tightly on the hose and are not cracked.

d. Check that the power head is properly latched to the drum, without gaps or

openings.

e. Check bleeder valve at the end of the hose.

3

4

2

6

8

9

10

11

12

13

14

16

15

1

5

7

16 ProTeam

PROGUARD LI 3 ASSEMBLY

PROGUARD LI 3 REPLACEMENT PARTS

ProTeam 17

ProGuard LI 3 Cordless

ORDER QTY.

# PRODUCT NAME NEEDED

1 510121 Power Head 1

2 510127 Switch and Switch Cover (Set) 1

3 833367 Drum Latch with Hinge (Set) 1

4 510122 Battery Cover/Hinge 1

5 832048 Filter Cage and Float Assembly 1

6 107178 Qwik Lock™ Fine Dust Cartridge Filter 1

7 833371 Drum with Labels 1

8 107197 Hose Assembly 1

9 107195 Dusting Brush 1

10 107196 Claw Nozzle 1

11 107194 Crevice Tool 1

12 107496 Battery 1

13 107490 Battery Charger 1

14 SP6989 Vacuum Owner’s Manual 1

15 SP6990 Battery Owner’s Manual 1

16 SP6971 Battery Charger Owner’s Manual 1

Repair Parts Assembly

All items sold as individual unless otherwise identified

WARRANTY

This limited warranty applies to the following ProTeam, Inc. commercial PROGUARD® Wet/Dry

Vacuums: ProGuard LI 3.

If you have any questions or need assistance regarding the warranty of your product,

please call ProTeam Customer Service department at (866) 888-2168 during the hours of

8:00 a.m. - 5:00 p.m. Central Time.

PROGUARD

®

- Limited Warranty

ProTeam, Inc., located at 8100 W. Florissant Ave., Building T., St. Louis, MO 63136 (“ProTeam”)

warrants to the original purchaser only (“you”) subject to the exclusions described below, that

the ProGuard Product component parts and motors listed below will be free from defects in

material and workmanship beginning on the original date of purchase and continuing for the

period set forth below (each a “Warranty Period”). This limited warranty terminates if the

original purchaser transfers the ProGuard Product to any other person or entity.

Parts Warranties - All ProGuard Products

• MoldedbodypartsonallProGuardProducts-ExpectedlifetimeoftheProGuardProduct.

• Allothercomponentparts(excludingthemotor)onallProGuardProducts-3years.

Motor Warranties - Specific to each ProGuard Product

• ProGuardLI3-VacuumMotor-1Year,IncludingBatteryandCharger.

What is Not Covered - Warranty Exclusions

This limited warranty does not extend to and expressly excludes:

• Normalwearandtearand/orreplacementattachmentsoraccessories,including,without

limitation, extension cords, hoses, filters, switches, carbon motor brushes and other

attachments to the ProGuard Product.

• DamageorburnoutoftheProGuardProductmotorresultingfromfailuretoclearablockage

occurring during the normal course of use.

• LossordamagetotheProGuardProductresultingfromconditionsbeyondProTeam’s

control including without limitation, misuse, accident, abuse, neglect, negligence (other

than ProTeam’s), overuse beyond intended capacity, or unauthorized modification or

alteration.

• LossordamagetotheProGuardProductresultingfromfailuretofollowtherequired

maintenance schedule, or failure to use the ProGuard Product in accordance with

ProTeam’s written instructions, guidelines or the terms of its Owner’s Manual.

What We Will Do to Correct Problems

If a claim made during the Warranty Period is covered under this limited warranty, ProTeam or

your local ProTeam authorized dealer will, at ProTeam’s sole option, (a) repair the defective

portion of the ProGuard Product or (b) replace the entire ProGuard Product. THE SOLE AND

EXCLUSIVE REMEDY FOR BREACH OF THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR

REPLACEMENT OF THE PROGUARD PRODUCT.

No Other Express Warranty Applies

THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES

PROVIDED BY PROTEAM TO THE ORIGINAL PURCHASER, AND ARE IN LIEU OF ALL OTHER

WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF

LAW OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE, WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED

AND WHETHER OR NOT THE PROGUARD PRODUCT HAS BEEN SPECIFICALLY DESIGNED OR

MANUFACTURED FOR YOUR USE OR PURPOSE. No employee, agent, dealer, or other person is

authorized to alter this limited warranty or make any other warranty on behalf of ProTeam.

The terms of this limited warranty shall not be modified by ProTeam, the original owner, or

their respective successors or assigns.

18 ProTeam

WARRANTY

How to Notify Us

If you discover that your ProGuard Product has a defect that you believe is covered by this

limited warranty, you must notify ProTeam or the ProTeam authorized dealer who sold you the

ProGuard Product within the applicable Warranty Period. You may contact ProTeam Customer

Service department at (866) 888-2168 during the hours of 8:00 a.m. and 5:00 p.m. Central

Time or at any time via the fax number or the email address listed in your Owner’s Manual

or on our website. In order for a warranty claim to be processed as quickly as possible, we

suggest that you complete the “Registration Card” made available to you on the ProTeam

website at www.pro-team.com. If you do not choose to register your ProGuard Product, in

order to make a warranty claim, you will need to provide a copy of your sales receipt or other

proof of purchase showing the purchase date to ProTeam or your local ProTeam authorized

dealer.

Repair and Replacement Procedures

Please call the Customer Service department number above or visit the ProTeam website

to find the ProTeam authorized dealer nearest you. If there is no local ProTeam authorized

dealer, our Customer Service department will give you the name and address of the nearest

field service representative or will provide you with instructions for shipping your ProGuard

Product to the ProTeam repair facility. ProTeam or your local ProTeam authorized dealer will

determine whether your claim is covered by this limited warranty, subject to the limitations or

exclusions described in this limited warranty, or has exceeded the applicable Warranty Period.

Your local ProTeam authorized dealer will repair your ProGuard Product, ship your ProGuard

Product to the dealer’s or ProTeam’s repair facility, or contact ProGuard for a replacement

ProGuard Product. The decision to replace your ProGuard Product is at the sole discretion of

ProTeam. Repairs or modifications made to the ProGuard Product by other than ProTeam,

its authorized repair facility or a local authorized dealer will nullify this limited warranty.

Coverage under this limited warranty is conditioned at all times upon the original purchaser’s

compliance with these required notification and repair procedures.

Limitation of Liability

TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL PROTEAM BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC

LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE

PROGUARD PRODUCT OR PROTEAM’S NEGLIGENCE. SELLER SHALL NOT BE LIABLE FOR DAMAGES

CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE

CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE,

STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL PROTEAM’S LIABILITY TO BUYER AND/

OR ITS CUSTOMERS EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE PROGUARD

PRODUCT. The term “consequential damages” shall include, but not be limited to, loss of

anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or

damage to property or equipment.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation may not apply to you. This limited warranty gives you specific legal rights,

and you may also have other rights which vary from State to State.

ProTeam 19

SP6989 Printed 03/16

ProTeam, Inc.

[email protected]

8100 W. Florissant Ave., Building T., St. Louis, MO 63136

866.888.2168

Page is loading ...

ProTeam ProGuard 3 Owner's manual

ProTeam ProGuard 3 Owner's manual

in other languages

Related papers

Other documents