Siemens DE24505/05 User manual

DE 18505

DE 21505

DE 24505

DE 27505

Gebrauchsanleitung

➔

2

Operating Instructions

➔

7

Notice d’utilisation

➔

12

Gebruikshandleiding

➔

17

Instrukcja u˝ytkowania

➔

22

Правила пользования

➔

27

Instrucciones de uso

➔

32

Instruções de utilização

➔

37

DE

EN

FR

NL

PL

RU

ES

PT

Page is loading ...

7

Please read the Operating Instructions carefully before using the appliance!

Safety information

■

Installation and first commissioning should only be undertaken by an authorized technician

according to the attached Assembly Instructions.

■

Repairs must only be undertaken by an authorized technician to exclude any potential risks

involved.

■

The continuous-flow heater must only be installed in a frost-free room.

■

The tap mixer and warm water pipe can get hot.

Keep children away from the appliance.

Your new appliance

■

The electronic “exclusive” continuous-flow heater warms water while it is passing through the

appliance.

■

The continuous-flow switches itself on and heats the water when the warm water tap is

opened. It switches itself off again when the water tap is closed.

How to operate the continuous-flow heater

Select the shower temperature

The basic setting for the water temperature after first commission-

ing or loss of electrical power is 40 °C.

■

The

rotary knob

is used to infinitely select the desired temper-

ature from 30 °C to 60 °C. The colored display lighting indicates the

temperature range during operation by means of blue or red hues.

Info: The temperature shown in the display is the water temperature

inside the appliance; the temperature of the water leaving the tap

can vary from this due to heat losses in the pipework.

The Wellness Program

The “exclusive” continuous-flow heater offers you the option to set two Wellness programs.

These Wellness programs begin with a warm phase and end with a cold phase. The temperature

change stimulus achieved can lead to stimulation of the circulation and an increase in blood

flow. Whether and to what degree the Wellness programs are suitable for you can, when in doubt

(particularly in the case of existing medical conditions), be discussed with your doctor.

8

Starting Wellness Program 1

■ Press on the Wellness Program button 1. The display lights up

in color and the stored shower temperature appears in °C and P1.

■ Now open the water tap within 2 minutes and Wellness

Program 1 starts. Warm water will run from the shower for 2 min-

utes according to the temperature setting and then cold water will

flow out for 30 seconds.

Tip: The best effect is obtained if you run Wellness Program 1 twice

in succession.

Starting Wellness Program 2

■ Press on the Wellness Programm button 2. The display lights up

in color and the stored shower temperature appears in °C and P2.

■ Now open the water tap within 2 minutes and Wellness

Program 2 starts. At first, warm water will run for 1 minute (water

temperature depends on your setting) and then 30 °C warm water

will be dispensed for 30 seconds.

Tip: Wellness Program 2 should be used a number of times in suc-

cession and can be repeated as often as desired.

Ending Wellness Program 1 or 2

Both programs will repeat until either the button 1 or 2 is pressed

(depending on the program selected) or the water faucet is shut off

for more than 2 minutes or the temperature setting is changed. The

temperature which was set before the program was started will be

re-activated.

The programs can also be activated while the water is running.

Changing the temperature in a Wellness Program

The preset temperature for the warm phase is 39 °C. This can be

altered within the range 30 °C to 42 °C.

■ Use the rotary knob to set the desired temperature within the

range 30 °C and 42 °C.

■ Store this value by holding down button 1 for three seconds.

The selected temperature is now stored in Wellness Program 1.

The temperature in Wellness Program 2 can also be altered in ex-

actly the same way. Store this by holding down button 2 for three

seconds.

9

Setting a temperature limitation/child protection

You have the possibility of limiting the temperature to 42 °C.

Switching on the “Symbol key”

■ Press buttons 1 and 2 simultaneously. The “Symbol key” ap-

pears in the display and the temperature is limited to 42 °C.

Switching off the “Symbol key”

■ Press buttons 1 and 2 simultaneously. The “Symbol key” dis-

appears in the display and the temperature is now freely selectable.

This means show the display

Saving energy

Mixing in of cold water in the fitting requires unnecessary water and

energy. You should therefore set the desired water temperature di-

rectly on the continuous-flow heater and then open the water tap.

If “eco” lights up in the display it means that the appliance is being

run economically.

Performance indicator

The performance indicator shows the currently used performance

of the continuous-flow heater in 10 % increments.

An example: 7 increments are shown while drawing off hot water.

This means that the continuous-flow heater is currently only running

at 70 % of its maximum output.

If the set temperature cannot be reached because the water

throughput is too high, the continuous-flow heater will automatical-

ly adjust the water throughput until the set temperature is achieved.

Pre-warmed water

The continuous-flow heater can be operated with pre-warmed wa-

ter (for example from a solar energy unit). The “Symbol Sun” will ap-

pear in the display if the feed water temperature is above 30 °C.

Service

Please seek to remove a fault according to guidelines given in the

chapter “A fault, what to do?” if “service” lights up in the display.

10

Using the appliance after switching off the water supply

■ Deenergize the appliance (unscrew the fuse in the house electrical installation).

■ Open the warm water tap and keep it open until the air has been completely forced out of the

water pipe.

■ Screw the fuse back in again.

■ The appliance is now ready to operate.

Cleaning

Only wipe off the appliance using a moist cloth. Do not use acidic or abrasive cleaning materials.

Customer Service

We ask you to always provide the E-No. and the FD-No. of your appliance when calling in a cus-

tomer service engineer. You will find the numbers on the inner side of the fold up operating panel

on the continuous-flow heater.

Siemens-Electrogeräte GmbH

11

A fault, what to do?

The reason for “service” to appear in the display is often very small. Please check whether you

can remove the fault yourself by using the following guidelines. You will save yourself the costs

of an unnecessary visit by customer service personnel.

If the fault could not be eliminated, please call customer service.

Fault Cause Solution Who

Water flow-rate is too

low.

The filter in either the water tap

or the showerhead is clogged.

Remove the filter and either

clean it or descale it.

Customer

The filter in the corner regu-

lating valve is clogged.

Clean the filter. Servicing expert

The water volume is

steadily reducing during

use.

Automatic regulation See chapter “The meaning

of display indications –

Performance indicator”

Customer

The temperature can not

be set warmer than

42 °C.

The child protection feature

is activated.

To deactivate child pro-

tection, see “How to operate

the continuous-flow heater –

Setting a temperature limi-

tation/child protection”

Customer

The desired water tem-

perature is set, but it is

not reached.

The continuous-flow heater

is connected to a thermo-

statically-controlled water

faucet.

The temperature at the con-

tinuous-flow heater must be

set to 60 °C.

Customer

The display is blank. The fuse in the house electrical

installation has triggered/blown.

Check the fuse in the house

electrical installation.

Customer

The appliance’s automatic cir-

cuit breaker has been triggered.

Check the appliance’s auto-

matic circuit breaker.

Servicing expert

The water is not warm. The fuse in the house electrical

installation has triggered/blown.

Check the fuse in the house

electrical installation.

Customer

From time to time, cold

water flows out.

The air sensor in the appliance

detects air in the water and mo-

mentarily switches the heating

element off.

After a few seconds, the

continuous-flow heater auto-

matically goes back into

operation.

Continuous-flow

heater automati-

cally resolves

problem

The set temperature, for

instance 41, blinks. The

temperature of the water

leaving the tap is higher

than the set tempera-

ture.

The temperature of the water

supplying the continuous-flow

heater is higher than the set

temperature (e.g. due to pre-

warmed water supplied from

a solar water heater).

Mix in cold water at the water

faucet supply.

Customer

“service” lights up. Deposits may have built up in

the appliance.

Open the warm water tap

fully to the warmest possible

setting and let the water flow

for one minute. Repeat as

necessary.

Customer

Page is loading ...

Siemens DE24505/05 User manual

Siemens DE24505/05 User manual

in other languages

Related papers

Other documents