Sub-Zero SRT304 Installation guide

Category
Cookers
Type
Installation guide
SEALED BURNER RANGETOP
INSTALLATION GUIDE
SPECIFICATIONS, INSTALLATION, AND MORE
2 | Wolf Customer Care 800.222.7820
SEALED BURNER RANGETOP
Contents
3 Specications
6 Installation
7 Troubleshooting
Features and specications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
wolfappliance.com | 3
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located on the bottom of the control panel,
at the far right. Refer to the illustration below.
If service is necessary, contact Wolf Factory Certied
Service with the model and serial number. For the name of
the nearest Wolf Factory Certied Service or for questions
regarding the installation, visit the Support & Service
section of our website, wolfappliance.com, or call Wolf
Customer Care at 800-222-7820.
Rating plate location
RATING PLATE
SPECIFICATIONS
Planning Information
When installing against a combustible surface, a minimum
5"
(127) riser is required for model SRT366, and a minimum
10"
(254) riser is required for 36" and 48" sealed burner
rangetops with a charbroiler or griddle. Follow all minimum
clearances to combustible surfaces shown in the illustra-
tion on page 5. Models SRT362W and SRT484W cannot be
installed against a combustible surface.
Electrical Requirements
Installation must comply with all applicable electrical codes.
Locate the electrical supply within the shaded area shown
in the illustration on page 5. A separate circuit servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded, 110/120 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle 3-prong grounding-type
Power Cord 6'
(1.8 m)
4 | Wolf Customer Care 800.222.7820
The rangetop must be connected to a regulated gas supply.
The supply line must be equipped with an approved external
gas shut-off valve located near the rangetop in an acces-
sible location. Do not block access to the shut-off valve.
Refer to the illustration below.
A gas supply of
3
/4" (19) ID line must be provided to the
rangetop. If local codes permit, a certied, 3'
(.9 m) long,
1
/2" (13) or
3
/4" (19) ID exible metal appliance connector is
recommended to connect the units
1
/2" NPT female inlet to
the gas supply line. Pipe joint compounds suitable for use
with natural or LP gas should be used.
The appliance and its shut-off valve must be disconnected
from the gas supply piping system during any pressure
testing of the system at test pressures in excess of .5 psi
(3.5 kPa)
. The appliance must be isolated from the gas
supply piping system by closing its individual manual shut-
off valve during any pressure testing of the system at test
pressures equal to or less than .5 psi
(3.5 kPa).
Wolf natural gas rangetops will function up to 10,250'
(3124 m)
in altitude without adjustment and LP gas ran-
getops up to 8,600'
(2621 m). If the installation exceeds
these elevations, contact your authorized Wolf dealer for
a high altitude conversion kit.
Gas Supply
Installation must comply with local codes or, in the absence
of local codes, with the National Fuel Gas Code.
Locate the gas supply within the shaded area shown in the
illustration on the following page.
The rangetop is equipped for use with natural or liquid
propane (LP) gas. It is design certied by the Canadian
Standards Association (CSA) for natural or LP gases. The
product rating plate has information on the type of gas that
should be used. For rating plate location, refer to the illustra-
tion below. If this information does not agree with the type
of gas available, check with the local gas supplier. The gas
pressure regulator is built into the unit.
GAS REQUIREMENTS
NATURAL GAS WC
Supply Pressure 5" (12.5 mb)
Min Line Pressure 7" (17.5 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
LP GAS WC
Supply Pressure 10" (25 mb)
Min Line Pressure 11" (27.4 mb)
Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)
SPECIFICATIONS
SHUT-OFF VALVE
OPEN POSITION
GAS SUPPLYTO APPLIANCE
Gas shut-off valve
Rating plate location
RATING PLATE
wolfappliance.com | 5
SPECIFICATIONS
FRONT VIEW
SIDE
VIEW
*W
ithout ventilation hood, 36" (914) minimum clearance countertop to combustible materials, 44" (1118) for charbroiler.
NO
TE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combus
tible materials cannot be located within this area.
El
ectrical and gas supply located through bottom of platform.
Fo
r island installation, 12" (305) minimum clearance back of rangetop to combustible rear wall above countertop.
13"
(330)
18"
(457)
6"
(152)
W
OPENING WIDTH
24" (610) MAX
PLATFORM
30" (762)
TO
36" (914)
TO BOTTOM OF
VENTILATION HOOD*
7
1
/2" (191)
OPENING
HEIGHT
PLATFORM
PLATFORM
TOP VIEW
16" (406)
ELECTRICAL
AND GAS
4"
(102)
E G
BACK WALL
Sealed Burner Rangetop
INSTALLATION
OPENING WIDTH
W
30" Model 30" (762)
36" Model 36" (914)
48" Model 48" (1219)
6 | Wolf Customer Care 800.222.7820
INSTALLATION
Preparation
Prepare the nished opening for the rangetop according to
dimensions shown in the illustration on the previous page.
The platform must include a cutout at the right rear for the
electrical and gas supply connections. It must be level to
ensure the cooking surface is level. Refer to the chart below
for the minimum base support.
INSTALLATION REQUIREMENTS
PLATFORM
Thickness
3
/4" (19)
BASE SUPPORT MIN
30" Rangetop 200 lb (91 kg)
36" Rangetop 250 lb (113 kg)
48" Rangetop 300 lb (136 kg)
Placement
Use an appliance dolly to move the unit near the opening.
Remove and recycle packing materials.
If a riser has been specied, refer to the installation instruc-
tions packaged with the riser. The riser must be installed
before the rangetop is installed.
Place the unit into the opening. Connect the gas and elec-
trical supply. The connections may need to be made prior to
nal placement.
For wok models, install the wok plate notch toward the front
of the unit. Refer to the illustration below.
NOTCH
Wok plate notch
wolfappliance.com | 7
Troubleshooting
IMPORTANT NOTE: If the rangetop does not operate prop-
erly, follow these troubleshooting steps:
Verify electrical power is supplied to the rangetop.
Verify the gas supply shut-off valve is in the open
position.
If the rangetop does not operate properly, contact Wolf
Factory Certied Service. Do not attempt to repair the
rangetop. Wolf is not responsible for service required to
correct a faulty installation.
Gas Supply Connection
All connections to the gas piping must be wrench-tightened.
Do not overtighten or allow pipes to turn when tightening.
If a exible metal connector is used, verify it is not kinked,
then attach the gas supply line to the regulator on the
rangetop. Open the valve and check for leaks by placing
a liquid detergent solution onto all gas connections.
Bubbles around the connections indicate a gas leak. If
a leak appears, close the shut-off valve and adjust the
connections.
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &
Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
INSTALLATION
wolfappliance.com | 7
故障排除
重要提示:如果灶台未正常工作,请按照以下故障排除步骤进
行操作:
确认灶台已通电。
检查燃气供应切断阀上方是否处于开启位置。
如果灶台未正常工作,请联系Wolf工厂认证的服务部门。
切勿尝试修理灶台。Wolf对纠正不当安装所需的服务概不
负责。
燃气供应连接
必须用扳手拧紧所有与燃气管道的连接。紧固时,切勿拧得过
紧或让管道转动。
如果使用柔性金属连接器,请确认其中不存在扭结,然后将燃
气供应管线连接到灶台调节器上。打开阀门,并将液体洗涤剂
溶液涂在所有燃气连接处以检查有无泄漏。连接处有气泡表示
存在燃气泄漏。如果出现泄漏,请关闭切断阀并调整连接。
Sub-ZeroSub-Zero & DesignSub-Zero & Snowake DesignDual RefrigerationThe Living KitchenGreat American KitchensThe Fine Art of Kitchen DesignWolf、
Wolf & DesignWolf GourmetW & Designred colored knobsCoveCove & Design均为Sub-Zero GroupInc.及其子公司的注册商标和服务标记。所有其他商标均为其各
自所有者在美国和其他国家(或地区)的财产。
WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820
9032800 REV-A 8/2019
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Sub-Zero SRT304 Installation guide

Category
Cookers
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI