Kenmore Elite 146.29164310 Owner's manual

Use & Care Guide

Manual de Uso y Cuidado

English / Espa_ol

Models/Modelos: 146.29163310/146.29164310/146.29162310

Items / Arficulos: 640-05280660-1/640-05280661-9/640-05280658-5

I<enmore Elite

@

Pro

gas de p *quSdo

@

P/N 30800317

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sears.com

www.kmart.com

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

1. Do not store or use gasoline or other

flammable liquids or vapors in the vicinity of

this or any other appliance.

2. An LP cylinder not connected for use shall not

be stored in the vicinity of this or any other

appliance.

Call Grill Service Center For Help And Parts

If you have questions or need assistance during assembly,

please call 1-888-287-0735. You will be speaking to a

representative of the grill manufacturer and not a Sears

employee. To order new parts call Sears at

1-800-4-MY-HOME ®.

Product Record

IMPORTANT: Fill out the product record information below.

Model Number

Serial Number

Date Purchased

See rating label on grill for serial number.

CAUT,ON

For residential use only. Do not use for commercial

cooking.

Installation Safety Precautions

• Please read this User's Manual in its entirety before using

the grill.

• Failure to follow the provided instruction can result in

seriously bodily injury and!or property damage.

• Some parts of this grill may have sharp edges. Please

wear suitable protective gloves.

• Use grill, as purchased, only with LP (propane) gas and the

regulator/valve assembly supplied.

• Grill installation must conform with local codes, or in their

absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and

Handling Code, B149.2, or the Standard for Recreational

Cehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV

Series, Recreational Vehicle Code, as applicable.

• All electrical accessories (such as rotisserie) must be

electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian

Electrical Code, CSA C22.1. Keep any electrical cords

and/or fuel supply hoses away from any hot surfaces.

• This grill is safety certified for use in the United States

and/or Canada only. Do not modify for use in any other

location. Modification will result in a safety hazard.

IMPORTANT: This grill is intended for outdoor use only and is

not intended to be installed in or on recreational vehicles or

boats.

NOTE TO INSTALLER: Leave this User's Manual with the

customer after delivery and/or installation.

NOTE TO CONSUMER: Leave this User's Manual in a

convenient place for future reference.

Safety Symbols

The symbols and boxes shown below explain what each heading

means. Read and follow all of the messages found throughout

the manual.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicatesan potentially hazardous situation

which,if notavoided, could resultindeath or seriousinjury.

CAUTION: Indicates a potentially hazardoussituationor

unsafepractice which, if notavoided, may resultin minoror

moderate injury.

2 ° 29163-30800317

For Your Safety ...

Grill Service Center...

Product Record Information...

Installation Safety Precautions...

Safety Symbols ...

Kenmore Grill Warranty...

Use and Care...

Parts List...

Parts Diagram ..

Before Assembly...

Assembly...

Troubleshooting...

.2

•4

... 5-13

•..14

• .15

... 16-18

•. •19-38

•. •39-41

Sears Installation Service

For Searsprofessional installation of home appliances, garage

door openers, water heaters, and other major home items,in

the U.S.A.call 1-800-4-MY-HOME ®

CALIFORNIA PROPOSITION 65

1. Combustion by-products produced when using this

product contain chemicals known to the State of

California to cause cancer, birth defects, and other

reproductive harm.

2. This Product contains chemicals, including lead and

lead compounds, known to the State of California

to cause cancer, birth defects or other reproductive

harm.

Wash your hands after using this product.

Repair Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore®

product is designed and manufactured for years of dependable

operation. But like all products, it may require repair from time to time

That'swhen having a RepairProtection Agreement can save you

money and aggravation.

Purc/Tasea Repair Protection Agreement now and protect yourself

from unexpected i?assleand expense.

Here's what the RepairProtection Agreement_ includes:

[] Expert service by our 10,000professional repair specialists

[] Unlimited service and no charge for parts and labor on all

covered repairs

[] Product replacement up to $1500 if your covered product

can't be fixed

[] Discount of 25% from regular price of service and related

installed parts not covered by the agreement; also,25% off

regular price of preventive maintenance check

[] Fasthelp by phone- we call it RapidResolution-

phone support from a Searsrepresentative. Thinkof us

asa "talking owner's manual."

Once you purchase the RepairProtection Agreement, a simple phone

call is all that it takes for you to schedule service.You can call

anytime day or night,or schedule a service appointment online.

The RepairProtection Agreement isa risk-free purchase. Ifyou

cancel for any reason during the product warranty period, we will

provide a full refund.Or, a prorated refund anytime after the

product warranty period expires. Purchaseyour Repair

Protection Agreement today!

Some limitationsand exclusionsapply. Forprices and

additional information in the U.S.A.call 1-800-827-6655.

29163-30800317 ° 3

Kenmore Elite Limited Warranty

When installed, operated and maintained according to all supplied instructions, free in-home warranty service is

provided from the date of purchase for the parts, time periods and conditions specified in the list below. Call

1-800-4-MY-HOME ® to arrange for warranty service.

Two years replacement and installation for all parts defective in material or workmanship

Five years replacement for a heat diffuser that rusts through or burns through

Fifteen years replacement for a burner that rusts through or burns through

Twenty-five years part replacement if the firebox cast aluminum sidewalls, lid porcelain coated shroud, or any

cooking grate rusts through or burns through

After the second year from the purchase date, you are responsible for the labor cost of part installation.

All warranty coverage excludes ignitor batteries and grill part paint loss, discoloration or surface rusting, which are

either expendable parts that can wear out from normal use within the warranty period, or are conditions that can be

the result of normal use, accident or improper maintenance.

All warranty coverage is void if this product is ever used for other than private household purposes.

This warranty applies only within the conditions stated above, and will NOT pay for:

1. Expendable items that can wear out from normal use within the warranty period, including but not limited to

batteries, light bulbs and surface coatings or finishes.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended

purpose.

6. Damage to or failure of this product resulting from natural catastrophe, such as flood, fire or storm.

7. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than

those recommended in all instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and

provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the

duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL60179

4 ° 29163-30800317

• NEVERstore a spare LPcylinder under or near the

appliance or in an enclosed area.

v v

• Never fill a cylinder beyond 80% full.

• If the information in the two points above is not

followed exactly, a fire causing death or serious

injury may occur.

• An overfilled or improperly stored cylinder is a

hazard due to possible gas release from the safety

relief valve. This could cause an intense fire with

risk of property damage, serious injury or death.

• If you see, smell or hear gas escaping,

immediately get away from the LP cylinder and

appliance and call your fire department.

LP Tank Removal, Transport And Storage

• TurnOFFall control knobs and LPtank valve. Turncoupling nut

counterclockwise by hand only - do not usetools to

disconnect. LiftLPtank wire upward off of LPtank collar, then lift

LPtank up and off of support bracket. Installsafety cap onto LP

tank valve. Always usecap and strap supplied with valve.

Failure to use safety cap as directed may result in serious

personal injury and/or property damage.

LPTank Valve, _

\,\ Safety Cap

__ RetainerStrap

• A disconnected LPtank in storage or being transported must

havea safety cap installed (as shown). Do not store an LPtank

in enclosed spaces suchas a carport, garage, porch, covered

patio or other building. Never leave an LPtank inside avehicle

which may become overheated by the sun.

° Do not store an LPtank in an area where children play.

LP Cylinder

• The LPcylinder used with your grill mustmeet the following

requirements:

• Use LPcylinders only with theserequired measurements:12"

(30.5cm) (diameter) x 18"(45.7 cm) (tall) with 20 lb. (9 kg.)

Capacity maximum.

• LPcylinders mustbe constructed and marked in accordance

with specifications for LPcylinders of the U.S.Department of

Transportation (DOT) or for Canada, CAN/CSA-B339,

cylinders, spheres andtubes for transportation of dangerous

goods. Transport Canada (TC). See LPcylinder collar for

marking.

• LPcylinder valve musthave:

° Type I outlet compatible with

regulator or grill.

• Safety relief valve.

• UL listedOverfill Protection

Device (OPD). ThisOPD safety OPDHandWheel

feature isidentified by a unique triangular hand wheel. Use

only LPcylinders equipped with this type of valve.

• LPcylinder must be arranged for vapor withdrawal and

include collar to protect LPcylinder valve. Always keep LP

cylinders in upright position during use,transit or storage.

LPcylinder in upright position for vapor withdrawal

LP (Liquefied Petroleum Gas)

• LPgas is nontoxic, odorless and colorless when produced. For

Your Safety, LPgas hasbeen given an odor (similarto rotten

cabbage) so that it can be smelled.

• LPgas is highly flammable and may ignite unexpectedly when

mixed with air.

LP Cylinder Filling

• Useonly licensed and experienced dealers.

• LPdealer mustpurge new cylinder before filling.

• Dealer should NEVERfill LPcylinder more than 80% of LP

cylinder volume. Volume of propane in cylinder will vary by

temperature.

• A frosty regulator indicates gas overfill. Immediately close LP

cylinder valve and call local LPgas dealer for assistance.

• Do not release liquid propane (LP)gas into the atmosphere. This

isa hazardous practice.

• To remove gas from LPcylinder, contact an LPdealer or call a

local fire department for assistance.Check the telephone

directory under "Gas Companies" for nearest certified LP

dealers.

29163-30800317 "5

LP Tank Exchange Connecting Regulator To The LP Tank

• Many retailers that sellgrills offer you the option of replacing

your empty LPtank through an exchange service Use only those

reputable exchange companies that inspect, precision fill, test

and certify their cylinders Exchange your tank only for an OPD

safety feature-equipped tank as described inthe "LPTank"

sectionof this manual

• Always keep new and exchanged LPtanksin upright position

during use,transit or storage

• Leaktest new and exchanged LPtanks BEFOREconnecting to

grill

1 LPtank mustbe properly secured onto grill (Referto

assembly section.)

2 Turnall control knobs to the OFFposition

3 TurnLPtank OFFby turningOPD hand wheel clockwise to a

full stop

4 Removethe protective cap from LPtank valve Always use

cap and strap supplied with valve

LP Tank Leak Test

For your safety

• Leaktest mustbe repeated each time LPtank isexchanged or

refilled

• Do not smokeduring leak test

• Do not usean open flame to check for gas leaks

• Grill mustbe leak tested outdoors ina wellventilated area,

away from ignition sources suchas gas fired or electrical

appliances During leak test, keep grill away from open flames

or sparks

• Usea clean paintbrush and a 50/50 mild soap and water

solution Brushsoapy solutiononto areas indicated by arrows

infigure below Leaksare indicated by growing bubbles

Safety Relief

Strap and Cap

_PDHand Wheel

_e1 outlet with

thread on outside

Do not insert a POL transport plug

(plastic part with external

threads) into the type 1 valve

outlet. It will defeat the Safety

Relief Valve feature.

• Do not usehousehold cleaning agents Damage to the gas

train components (valve/hose/regulator) can result

5 Hold regulator and insert nipple into LP

tank valve Hand tighten the coupling

nut,holding regulator in a straight line

with LPtank valve so as not to crossth

thread the connection

Nipple has to be

centered into the LP

tank va Ilii\_'_.

6 ° 29163-30800317

Hold coupling nut and regulator

as shown for proper connection

to LPtank valve.

Leak Testing Valves, Hose and Regulator

1.Turnall grill control knobsto OFF.

2Be sure regulator is tightly connected to LPtank

3Completely open LPtank valve by turning OPD hand wheel

counterclockwise If you hear a rushing sound, turn gas off

immediately There is a major leak at the connection Correct

before proceeding by calling Sears for replacement parts at

1-800-4-MY-HOME ®

4Brush soapy solutiononto areas where bubbles are shown in

picture below:

6 Turn the coupling nutclockwise andtighten to a full stop The

regulator will seal onthe back-check feature in the LPtank

valve, resulting in someresistance An additional one-half to

three-quarters turn isrequired to complete the connection.

Tighten by hand only - do not usetools.

NOTE:

Ifyou cannot complete the connection, disconnect regulator

and repeat steps5 and 6.If you are still unable to complete the

connection, do not usethis regulator!

Call 1-800-4-MY-HOME ® for an identical replacement part.

• Never remove threaded

orifice at:nd of valve.

• Do not insert any tool or foreign object into the valve

outlet or safety relief valve You may damage the valve

and cause a leak Leaking propane may result in

explosion, fire, severe personal injury, or death

• Outdoor gasappliance isnot intendedto be installed

inor on a boat

• Outdoor gasappliance isnot intendedto be installed

in or on an RV

• Never attempt to attach thisgrill to the self-contained

LPgas systemof a camper trailer or motor home

• Do not usegrill until leak-tested

• If a leak isdetected at anytime, STOPand call thefire

department

• If you cannot stop a gas leak,immediately close

LPcylinder valve and call LPgassupplier or your fire

department !

5 If _'growing_'bubbles appear, there isa leak CloseLPtank

valve immediately and retighten connections If leakscannot be

stopped do not try to repair Call for replacement

parts at 1-800-4-MY-HOME®

6 Always close LPtank valve after performing leak test by

turning hand wheel clockwise

29163-30800317 ° 7

For Safe Use of Your Grill and to Avoid Serious

Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that

burn.

• Do not block holes in sides or back of grill.

• Use grill only in well-ventilated space. NEVER use

in enclosed space such as carport, garage, porch,

covered patio, or under an overhead structure of

any kind.

• Do not use charcoal or ceramic briquets in a gas

grill.

• Use grill at least 3 ft. from any wall or surface.

Maintain 10 ft. clearance to objects that can catch

fire, or to sources of ignition such as pilot lights on

water heaters, live electrical appliances, etc.

• Apartment Dwellers:

Check with management to learn the requirements

and fire codes for using an LPgas grill in your

apartment complex. If allowed, use outside on the

ground floor with a three (3) foot clearance from

walls or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A

buildup of non-ignited gas inside a closed grill is

hazardous.

• Never operate grill with LPcylinder out of correct

position specified in assembly instructions.

• Always close LPcylinder valve and remove

coupling nut before moving LPcylinder from

specified operation position.

Safety Tips

• Before opening LPcylinder valve, check the coupling nutfor

tightness.

• When grill isnot inuse,turn off all control knobsand LPcylinder

valve.

• Never move grill while in operation or still hot.

• Use long-handled barbecue utensilsand oven mittsto avoid burns

and splatters.

• Maximum load for sideburner and side shelfis 10Ibs.

• Thegrease tray mustbe insertedinto grill and emptied after each

use.Do not remove grease tray until grill hascompletely cooled.

• Clean grill often, preferably after each cookout. Ifa bristle brush is

usedto clean any of the grill cooking surfaces,ensureno loose

bristlesremain on cooking surfaces prior to grilling. Itis not

recommended to clean cooking surfaces while grill ishot.

• If you notice grease or other hot material dripping from grill,

determine the cause,correct it, then clean and inspectvalve. Keep

ventilation openingsin cylinder enclosure (grill cart) free and clear

of debris.

• Do not store objects or materials insidethe grill cart enclosure that

would block the flow of combustion air to the underside of either

the control panel or the firebox bowl.

• The regulator may make a hummingor whistling noiseduring

operation. Thiswill not affect safety or useof grill.

• If you havea grill problem see the "Troubleshooting Section".

• If the regulator frosts,turn off grill and LPcylinder valve

immediately. Thisindicates a problem with the cylinder and it

shouldnot be usedon any product. Returnto supplier!

• Putting out grease fires by closing the lid is not possible.

Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may

result. If a grease fire develops, turn knobs and LP

cylinder off.

• Do not leave grill unattended while preheating or burning

off food residue on HI. If grill has not been regularly

cleaned, a grease fire can occur that may damage the

product.

Main Burner Igniter Lighting

• Do not lean over grill while lighting.

1.Open lid during lighting.

2.Turnonvalve from source or tank.

3.Pushand turn any Main Burnercontrol knob to _ Hi

and hold in. You will hear a clicking sound from the

electrodes of all burners.

4. Ifignition does not occur in5seconds,turn the burner

controls OFF,wait 5 minutes,and repeat the lighting

procedure.

5. To ignite any other Main Burner,turn knob to HI.

Ifigniter does not work, follow Match Lightinginstructions.

8 ° 29163-30800317

Turn controls and gas source or tank OFF when not

in use.

CAUTION

If ignition does NOT occur in 5 seconds, turn the

burner controls OFF, wait 5 minutes and repeat the

lighting procedure. If the burner does not ignite with

the valve open, gas will continue to flow out of the

burner and could ignite with risk of injury.

Match Lighting

ADo not lean over grill while lighting.

1.Open lid during lighting.

2. Place match into match holder (hanging on back of left door).

Lightmatch, place into lighting hole on left side of firebox.

3. Turnright knob to HI position. Besure burner lightsand stay lit.

4. Lightother burners follow with step 3.

Burner Flame Check

• Removecooking grates and heatdiffusers.Light burners,turn

knobsfrom HI to LO. You shouldseea smaller flame in

LO position than seen on HI. Perform burner flame check

on sideburner, also. Always check flame prior to each use.If

only low flame isseenrefer to "Suddenflame drop or low flame" in

the Troubleshooting Section.

Turning Grill Off

• Turnall knobsto OFFposition. Turn LPcylinder off by turning

Igniter Check

• Turngas off at LPcylinder. Pressand hold electronic igniter

button."Clicking" shouldbe heard and spark seen each time

between collector box or burner and electrode. See

"Troubleshooting" if no click or spark.

Valve Check

• Important: Make sure gas isoff at LPcylinder before

checking valves. Knobs lock in OFFposition. To check

valves, first pushinknobs and release, knobs shouldspring

back. If knobs do not spring back, replace valve assembly

before usinggrill. Turnknobsto LOW position thenturn back to

OFFposition.Valves shouldturn smoothly.

Hose Check

• Before each use,check to see if hosesare cut or worn.

Replacedamaged hosesbefore usinggrill. Useonly

valve/hose/regulator asspecified in the parts list of thisUse & Care

Guide.

General Grill Cleaning

• Do not mistake brown or black accumulation of grease and

smokefor paint. Interiorsof gas grills are not painted at the

factory (and should never be painted). Apply a strong solution

of detergent and water or usea grill cleaner with scrub brush

on insidesof grill lid and bottom. Rinseand allow to completely

air dry. Do not apply a caustic grill/oven cleaner to painted

surfaces.

• Porcelain surfaces: Because of glass-like composition, most

residue can be wiped away with baking soda/water solution or

specially formulated cleaner Usenonabrasive scouring powder

for stubborn stains

• Paintedsurfaces: Wash with mild detergent or nonabrasive

cleaner and warm soapy water Wipe dry with a soft

n.onabrasivecloth

• Stainlesssteel surfaces:To maintainyour grill's high quality

appearance, wash with mild detergent and warm soapy water

andwipe dry with a soft cloth after each use Baked-on grease

deposits may require the useof an abrasive plastic cleaning

pad Use only in direction of brushed finishto avoid damage

Do not useabrasive pad on areas with graphics

• Cooking surfaces: If a bristle brushisused to clean any of

the grill cooking surfaces,ensureno loose bristles remainon

cooking surfaces prior to grilling It isnot recommended to

clean cooking surfaceswhile grill ishot

29163-30800317 ° 9

CAUTION

SPIDER ALERT!

IMPORTANT: Always ensure that the venturi burner tubes

are clean. A venturi burner tube hasa narrow area in

which spiders tend to build nests.

Ifyou notice that your grill isgetting hard to light or that the

flame isn't asstrong asit shouldbe, take the time to check and

clean the venturi's.

- !

Spiders or small insects have been known to create "flashback"

problems. The spiders spinwebs, build nestsand lay eggs in the grill's

venturi tube (s) obstructing the flow of gas to the burner. The

backed-up gas can ignite in the venturi behind the control panel. This

isknown as a flashback and it can damage your grill and even cause

injury.

Topreventflashbacksandensuregood performancethe burnerand

venturiassemblyshouldbe removedfromthegrilland cleaned

'beforeusewheneverthegrill hasbeenidleforanextendedperiod.

Storing Your Grill

•Clean cooking grates

•Store in dry location

•When LPcylinder isconnected to grill, store outdoors in a

wellventilated space and out of reach of children

•Cover grill if stored outdoors Choose from a variety of grill

covers offered by manufacturer once available

•Store grill indoors ONLY if LPcylinder isturned off and

Disconnected, remove from grill and stored outdoors

• When removing grill from storage, follow "Cleaning the Burner

Assembly' instructionsbefore starting grill

Cleaning the Burner Assembly

Follow these instructionsto clean and/or replace parts of burner

assembly or if you havetrouble igniting grill

1 Turn gas off at control knobsand LPcylinder

2 Removecooking grates and heat diffusers

3 Removecotter pinfrom rear of burners

4 Carefully lift each burner up and away from valve openings

We _uggestthree ways to clean the burner tubes Usethe one

easiestfor you

(A) Benda stiff wire (a light weight coat hanger works well)

into a small hook Runthe hookthrough each burner

tube several times

Z2Z Z]L] Z2 .....

(B) Usea narrow bottle brushwith a flexible handle (do not use

a brasswire brush), runthe brushthrough each burner tube

several times

(C) Wear eye protection: Use an air hoseto force air into

the burner tube and out the burner ports Check each

port to makesure air comes out each hole

5 Wire brushentire outer surface of burner to remove

food residue anddirt

6 Clean any blocked ports with a stiffwire such asan

open paper clip

7 Check burner for damage, dueto normal wear and

corrosion some holes may become enlarged If any large

cracks or holes are found replace burner

VERYIMPORTANT: Burnertubes mustreengage valve

openings.Seeillustrations below.

8 Carefully replace burners

9 Attach burners to brackets with cotter pin

10 Replace heat diffusers and cooking grates

10 ° 29163-30800317

Indirect Cooking

Poultry and large cutsof meat cook slowly to perfection onthe grill

by indirect heat. Place food over unlit burner(s);the heatfrom lit

burners circulates gently throughout the grill, cooking meat or

poultry without the touch of adirect flame. This method greatly

reduces flare-ups when cooking extra fatty cuts because there isno

direct flame to ignite the fats and juices that drip during cooking.

1 Burner Cooking

Cook with direct or indirect heat.

Bestfor smaller mealsor foods.

Consumeslessfuek

Indirect Cooking Instructions

• Always cook with the lid closed.

° Dueto weather conditions, cooking times may vary. During

cold and windy conditions the temperature setting may

need to be increased to insuresufficient cooking

temperature.

° Place food over over unlit burner(s).

2 Burner Cooking

Great indirect cooking on low.

ProducessJow,even heating.

Ideal for slow roastingand baking.

Food Safety

Food safety isa very important part of enjoying the outdoor

cooking experience. To keep food safe from harmfulbacteria,

follow thesefour basic steps:

Clean: Wash hands,utensils,and surfaceswith hot soapy water

before and after handling raw meat and poultry.

Separate: Separate raw meats and poultry from ready-to-eat

foods to avoid cross contamination. Use a clean platter and

utensilswhen removing cooked foods.

Cook: Cook meat and poultry thoroughly to kill bacteria. Use a

thermometer to ensureproper internal food temperatures.

Chill: Refrigerate prepared foods and leftovers promptly. For

more information call: USDAMeat and Poultry Hotline at

1-800-535-4555 (InWashington, DC (202) 720-3333, 10:00 am

4:00 pm EST).

How To Tell If Meat Is Grilled Thoroughly

• Meat and poultry cooked on a grill often browns very fast

on the outside. Use a meat thermometer to be surefood has

reached a safe internal temperature, and cut into food to

check for visual signsof doneness.

° Whole poultry should reach 180° F; breasts,170° F.Juices

should runclear and fleshshould not be pink.

° Hamburgers made of any ground meat or poultry should

reach 160° F,and be brown in the middle with no pinkjuices

Beef, veal and lamb steaks, roasts and chops can be

cooked to 145° F.All cutsof pork should reach 160° F.

° NEVERpartially grill meat or poultry and finishcooking

later. Cook food completely to destroy harmful bacteria.

° When reheating takeout foods or fully cooked meats like

hot dogs, grill to 165° F,or until steaminghot.

WARNING: To ensurethat it is safe to eat,food mustbe cooked

to the minimuminternal temperatures listed in the table below.

USDA* RecommendedSafeMinimum Internal Temperatures

Beef,Veal, Lamband Pork Whole Cuts_ 145° F

Fish 145° F

Beef,Veal, Lamband Pork Ground 160° F

Egg Dishes 160° F

Turkey, Chicken & Duck Whole, Pieces & 165°F

Ground

United StatesDepartment of Agriculture

_AIIow meat to rest three minutesbefore carving or consuming.

29163-30800317 ° 11

To purchase Natural Gas Conversion Partscall Searsat

1-800-4-MY-HOME ®

Natural Gas Conversion Kit

Service Part 30800331

Or In-store part 30611

item: 590-06109657-4

Your grill can be converted to natural gas with this

conversion kit by a qualified gas technician only. To

convert this grill the technician will need thisconversion kit.

iiiiiii

Naturalgas 12'hose

If converting the grill to natural gas, the technician in

mostcases will need this 12'extension hosewith 3/8" ID

(innerdiameter), which is included in the natural gas

conversion kit.

12 ° 23674-30800316

Gas Requirements

For Natural Gas Connection

Preparing:

1. Turnoff gas supply,and thenremove cap on gas

Supply side.

2. Recommended: Installa shut-off valve on

gas supply side before installingthe socket.

3. Socket should be installed by an authorized

technician in accordance with the national fuel gas

code (NFPA54/ANSI223.1)

4. Before inserting plug,turn on gas supply and leak

test all connections including the stemof the shut-off

valve and the opening of the socket. Forbest results,

useand ammonia-free soap & water solution.

Operating Instructions:

1.Toconnect, pushback socket sleeve.

Socket Sleeve _ Plug

LPGas

If your grill isfor [P Gas, the regulator supplied isset for

an 11-in.Water column (WC} and is for usewith I.Pgas

only. The factory-supplied regulator and hose must be

usedwith a 20-lb. I.Pgas tank.

Natural Gas

If your grill isfor Natural Gas, it is set for a 7-in. water

column (WC} and is for usewith Natural Gas only.Gas

pressure is affected by gas line size and the length of

gas line run from house gas line. Follow the

recommendations inthe chart below.

From House to Grill

Distance Tubing Size

Up to 25 ft. 3//8 in. diameter

26-50 ft. i/2 in. diameter

51-100 ft. 2/3 of the run: 3/4 in. diameter

1//3 of the run: 1/2 in. diameter

Over 101 ft. 3//,4 in. diameter

2. Insertplug and release sleeve.

3. Pushplug untilsleeve snapsforward. (Gas will flow

automatically. Failureto connect plug properly to

socket will inhibitgas flow to the appliance.}

Socket S_eeve

To disconnect

1. PullSleeve back. Pullplug out socket. (Gas is

automatically shutoff.}

2. Close shut-off valve and replace dust caps on socket

and plug.

29163-30800317 ° 13

Key

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

3O

31

32-1

32-2

32-3

33-1

Description Qty

End Cap, Right Side Shelf 1

Right Side Shelf 1

Fascia, Right Side Shelf 1

Control Panel 1

Pulse Control Line 1

Pulse Ground Wire 1

Gas Valve, Main Burner 3

Manifold 1

Gas Hose 1

Regulator Retention Bracket 1

Connector B 1

Regulator 1

Regulator Hose Hanger Clip 1

Control Knob Bezel 3

Control Knob 3

Bottom Shelf 1

Magnet Box 1

Magnet 4

Caster 2

Caster with Brake 2

Tank Positioning Pin 2

Cart Support Angel Bar 2

Right Door Pin Support 1

Left Door Pin Support 1

Right Side Panel 1

Grease Box 1

Grease Box Bracket Support 1

Grease Box Bracket 1

Door Handle 2

Match Holder 1

Match Holder Bracket 1

Right Door (Metallic Black) 1

Right Door (Vermillion Red} 1

Right Door (Champaign) 1

Left Door (Metallic Black) 1

Pad Number

30800206

30800041

30800044

30800024

30800224

30800225

30800212

30800028

30800217

30800054

30800218

40800115

30800226

40900036

30800219

30800074

40200072

40200094

40900213

40900212

30800229

40900060

30800058

30800057

30800051

30800082

30800081

30800080

30800068

40800128

40800129

30800066B

30800066C

30800066D

30800060B

Key Description Qty

33-2 Left Door (Vermillion Red} 1

33-3 Left Door (Champaign} 1

34 Left Side Panel 1

35 Back Panel 1

36 Hex Nut 1

37 Electronic Ignition Module 1

38 Main Burner Electrode L850 1

39 Main Burner Electrode L650 1

40 Main Burner Electrode L450 1

41 Grease Panel 1

42 Main Burner 3

43 Fascia, Left Side Shelf 1

44 End Cap, Left Side Shelf 1

45 Left Side Shelf 1

46 Lid Handle 1

47 Rubber Bumper, Lid 2

48 Rubber Bumper, Lid 2

49 Temperature Gauge 1

50 Temp Gauge Bezel 1

51 Logo 1

52 Rotate Rod, Lid 2

53 Lid Handle Spacers 2

54 Bezel, Lid Handle 2

55 Cotter Pin 5

56-1 Lid ( (Metallic Black) 1

56-2 Lid (Vermillion Red) 1

56-3 Lid (Champaign) 1

57 Warming Rack 1

58 Cooking Grid 2

59 Heat Diffuser 3

60 Firebox 1

61 Door Bracket 1

62 Fuel Gauge 1

63 Badge 1

Pad Number

30800060C

30800060D

30800049

30800053

30800218

30800223

30800220

30800221

30800222

30800019

30800086

30800036

30800205

30800031

30800010

40700103

40800107

30800207

30800208

30800209

40800108

30800231

30800011

110024

30800002B

30800002C

30800002D

30800210

30800211

30800018

30800013

30800056

30800087

30800232

Not Pictured

Hardware Pack 1

Manual 1

Natural Gas Conversion Kit, Purchase Separately 1

See Pages 12 & 13

30800330

30800317

30800331

If you are missinghardware or have

damaged parts after unpacking grill,

call 1-888-287-0735 for replacement.

To order replacement parts after usinggrill,

call 1-800-4-MY-HOME ®

14 " 29163 -30800317

Page is loading ...

READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTSFROM

SHiPPiNG BOX.

Step 1: Use a box cutter knife to slice down the sides of the carton box. Be careful of staples

along the edges. Remove all parts, part boxes, and packing material from the top, sides and

bottom of cjrill head.

16 " 29163-30800317

Step 2: Tilt grill head up to one side and then to other side to remove large Styrofoam side pieces. Also,

remove packing material from regulator hose and igniter wires. Besure to remove grease tray from left

Styrofoam side piece.

_ _ _'_ ¸¸,¸3_ ,,_ ¸¸¸¸,¸¸¸¸2,,i_ _ ,,_

29163-30800317" 17

Step 3: With grill head resting on base on shipping box cardboard, raise grill head lid, and remove all

part boxes and packing material from inside the grill head. Allow grill head to rest on cardboard until

placing grill head on cart during assembly.

V

18 * 29163-30800317

CAREFULLY READ AND PERFORM ALL ASSEMBLY iNSTRUCTiONS ON THE FOLLOWING PAGES.

Tools Required:

• Adjustable wrench (not provided)

• 7/16" Combination wrench (not provided)

• The following hardware is provided in blister pack for convenient use.

M4X10 Screws

Qty: 42 pcs

M5X10 Screws

Qty: 4 pcs

M6X13 Screws (Black)

Qty: 26 pcs

Tank Positioning Pin

Qty: 2 pcs

M4X12 Screws

Qty: 2 pcs

M5 flat washer

Qty: 4 pcs

M6X13 Screws (gray)

Qty: 12 pcs

AA Battery

Qty: 1 pc

M6X20 Screws

Qty: 4 pcs

M6 flat washer

Qty: 4 pcs

29163-30800317 " 19

Casters to Cart Base

[] Turncart base upside down. Attach the castersto cart base with (16)M6 X 13black screws.

Casters with brakes attach to rear of cart base.

M6X13 screws (Black) Qty: 16 pcs

Swivel Casters

v

Panel Front

Swivel Caster

with Brake

Panel Rear

20 " 29163-30800317

lUrn cart base fight side up. Attach door

M4XIO SCrews Qty: 2 pcs

magnets to cart base with C2)M4xlO Screws.

\\\

\

Page is loading ...

Kenmore Elite 146.29164310 Owner's manual

This manual is also suitable for

Kenmore Elite 146.29164310 Owner's manual

in other languages

Related papers

Other documents