Before calling service
ENGLISH
12
3
6
9
• Allow your refrigerator to operate and
cool down for 24 hours (1 full day) be -
fore the ice maker starts producing ice.
•
-
pacity, dispense a few cubes 8 and 16
hours after installation.
•
If ICE OFF is lit, the ice maker will not make ice.
• To activate the ice maker, press the ICE OFF
but-ton on the control panel so it is no lon -
ger lit.
• When installing, servicing or cleaning behind the
refrigerator, be sure of the following:
•
refrigerator, cut a large section of the cardboard
carton and place under the refrigerator where
you are working.
• Pull the unit straight out and push back in
kcehC • if the ice bucket is completely
inserted. (On some models)
• Freezer temp may not be enough;
set it to -2ºF(-19ºC) or lower.
•
cubes may be produced.
•
After installation or when replacing the
1 gallon (2~3minutes) of water to
remove trapped air from the water line.
Otherwise, water may drip after dis -
pensing water. (On some models)
•
because the stored water in the water valve has
not cooled completely. Dispense several glasses
of water and then it would be cool.
ehT .1 Water Line must be fully Inserted to the center
of transparent coupler to prevent water leakage
from the dispenser.
• These noises may be heard occasionally inside
the refrigerator. This is normal. This sound occurs
when various items contract or expand while
temperatures are changing; especially during
defrosting. This may also occur when electronic
devices including the ice maker are operating.
• You can select your Pantry
temperature from among the
following.
Wine Party Dishes (38°F[3°C])
Fresh (38°F[3°C])
Chilled (34°F[1°C])
Deli (41°F[5°C])
•
control lever, turn it clockwise or counter-clock -
wise to level the door.
•
•
•
properly, air could penetrate into the water line
causing water dripping from the water dispenser.
• CAUTION :
Insert the water line into the coupler com -
pletely and slide in the clip at the end of the coupler.
Red Clip
(1/4")
Dispenser
Door Tube
Cabinet
Tube
DA99-04014A Rev 04
•
clockwise so it is aligned with the
printing mark on the cover, lock -
-
ter printing as illustrated.
• eht gnitresni fo elbuort ni era uoy fI
water supply valve. For details, refer to the “Chan -
refer ,sliated roF
to the user manual “Adjusting the level”
• Recommended Temp Settings : 0ºF(-18ºC) for
freezer and 37ºF (3ºC) for refrigerator.
•
use water about 300 gallons (6 month) Reset the indi -
the "Ice Type/Water/Hold 3 sec for Filter Reset"
button for 3 seconds.
• Ice
: Press the “Ice ” button to turn the ice
making function o
.
The display may di
er depending on models.
For details, refer to the user manual “Using the control
panel.
If you have further questions or damaged accessory parts, contact us at 1-800-SAMSUNG (726-7864)
PUSH
Control Lever
Flat-blade screw driver(-)
<sample>
1. Automatic Ice Maker does not work
2. Slow Ice cube freezing
3. Small or bubbled ice cubes or Slow
water dispensing
5. Water is not cool enough
(On some
models)
4. Water filter replacement
•
Allow your refrigerator to operate and cool down for
24 hours (1 full day) to reach to the set temperature.
tup uoy nehw ,oslA • room temperature or warmer
food into your refrigerator, it may need an additional
24 hours for the fridge to reach the set temperature.
7. Fridge or freezer Compartments are
warm
• Wipe o the condensation with a dry towel (This
may occur during hot and humid seasons.)
• If the condensation occurs on the doors, turn off
the Energy Saving function.
f srood eht nepo uoy fI • requently or for too long, it
may cause moisture inside the fridge.
fo edisni/edistuo no smrof erutsioM .8
refrigerator
9. Noise Clicks, Pops, Cracks, Snaps
6. Water dispenser dripping
(On some
models)
10. Display 13. Moving and Installing
• If food with too much moisturere is stored near the
cooling vents, it may get frozen. Be sure to keep
moist food away from the cooling vents.
12. Food stored in refrigerator is frozen
11. Cool Select Pantry (On some models)
14. Leveling & Door Alignment
DA99-04014A(EN+FR+ES)-0.3.indd 1 2012.4.2 1:55:39 PM
If the water line is not inserted into the coupler
2. Insert the clip in the install pack and check that it
Pull out the freezer drawer , then you can
see the lower hinge .
Adjust the height by turning a philips
screwdriver (+) clockwise ( ) or
counterclockwise ( ).
1
2
3
4
Insert a philips screwdriver (+) into the shaft
of the lower hinge.
DOWN
UP
3
1
2
3
4
3
•
•
