Philips AJ260/05 Quick start guide
- Category
- Alarm clocks
- Type
- Quick start guide
Philips AJ260/05 is an easy-to-use clock radio with a range of features to help you wake up and stay informed. Here are some of the things you can do with your new clock radio:
- Wake up to the radio or a buzzer. You can choose to wake up to your favorite radio station or to a gentle buzzer sound.
- Set two separate alarms. This is perfect for couples who need to wake up at different times or for people who want a backup alarm in case they oversleep.
- Tune in to your favorite radio stations. The AJ260/05 has a built-in AM/FM tuner so you can listen to your favorite radio stations.
Philips AJ260/05 is an easy-to-use clock radio with a range of features to help you wake up and stay informed. Here are some of the things you can do with your new clock radio:
- Wake up to the radio or a buzzer. You can choose to wake up to your favorite radio station or to a gentle buzzer sound.
- Set two separate alarms. This is perfect for couples who need to wake up at different times or for people who want a backup alarm in case they oversleep.
- Tune in to your favorite radio stations. The AJ260/05 has a built-in AM/FM tuner so you can listen to your favorite radio stations.
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
•For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
Note:
– Refer to the supplied user manual for more
information about the outdoor sensor.
AJ260
Clock Radio
QUICK START
3 ways to switch off the alarm
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Radio
1.
Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
Weather forecast and Indoor
thermometer
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
ENGLISH
Step A
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step B
How to set the Clock & Alarm time
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC. is
displayed.
Notes:
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
In standby mode, slide the RADIO/BUZ to select
desired mode.
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
C
A
B/3
3
R
B
DC 7.5V
R
Printed in China
PDCC-JH-0710
AJ260_05-QSG 8/3/07, 12:001
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
•For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
Note:
– Refer to the supplied user manual for more
information about the outdoor sensor.
AJ260
Clock Radio
QUICK START
3 ways to switch off the alarm
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Radio
1.
Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
Weather forecast and Indoor
thermometer
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
ENGLISH
Step A
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step B
How to set the Clock & Alarm time
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC. is
displayed.
Notes:
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
In standby mode, slide the RADIO/BUZ to select
desired mode.
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
C
A
B/3
3
R
B
DC 7.5V
R
Printed in China
PDCC-JH-0710
AJ260_05-QSG 8/3/07, 12:001
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
•For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
Note:
– Refer to the supplied user manual for more
information about the outdoor sensor.
AJ260
Clock Radio
QUICK START
3 ways to switch off the alarm
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Radio
1.
Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
Weather forecast and Indoor
thermometer
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
ENGLISH
Step A
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step B
How to set the Clock & Alarm time
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC. is
displayed.
Notes:
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
In standby mode, slide the RADIO/BUZ to select
desired mode.
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
C
A
B/3
3
R
B
DC 7.5V
R
Printed in China
PDCC-JH-0710
AJ260_05-QSG 8/3/07, 12:001
-
1
-
2
-
3
Philips AJ260/05 Quick start guide
- Category
- Alarm clocks
- Type
- Quick start guide
Philips AJ260/05 is an easy-to-use clock radio with a range of features to help you wake up and stay informed. Here are some of the things you can do with your new clock radio:
- Wake up to the radio or a buzzer. You can choose to wake up to your favorite radio station or to a gentle buzzer sound.
- Set two separate alarms. This is perfect for couples who need to wake up at different times or for people who want a backup alarm in case they oversleep.
- Tune in to your favorite radio stations. The AJ260/05 has a built-in AM/FM tuner so you can listen to your favorite radio stations.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Philips VR 206 Quick Start
-
-
-
-
-
Philips AJ260 User manual
-
Philips AJ3600/00C User manual
-
-
-
Other documents
-
La Crosse Technology DCF-77 User manual
-
EKO KAC3 User manual
-
Techno line Model Owner's manual
-
Ambient Weather RC-8401 Owner's manual
-
Ambient Weather RC-8401A Owner's manual
-
Sharper Image Weather Projection Clock Owner's manual
-
Ambient Weather RC-8365 Owner's manual
-
Bresser 70-04403 Owner's manual
-
Sencor SDC 8200 User manual
-
La Crosse Technology WT-5442 User manual
