CTC Union IEXT224-4PH-L User manual

CTC Union
Brand
CTC Union
Model
IEXT224-4PH-L
Category
PoE adapters
Type
User manual

This manual is also suitable for

1
IEXT224-4PH-L
IEXT224-4PH-R
Long Reach POE Extenders
2
LEGAL
The information in this publication has been carefully checked and is believed to be entirely
accurate at the time of publication. CTC Union Technologies assumes no responsibility, however,
for possible errors or omissions, or for any consequences resulting from the use of the information
contained herein. CTC Union Technologies reserves the right to make changes in its products or
product specifications with the intent to improve function or design at any time and without notice
and is not required to update this documentation to reflect such changes.
CTC Union Technologies makes no warranty, representation, or guarantee regarding the suitability
of its products for any particular purpose, nor does CTC Union assume any liability arising out of
the application or use of any product and specifically disclaims any and all liability, including
without limitation any consequential or incidental damages.
CTC Union products are not designed, intended, or authorized for use in systems or applications
intended to support or sustain life, or for any other application in which the failure of the product
could create a situation where personal injury or death may occur. Should the Buyer purchase or
use a CTC Union product for any such unintended or unauthorized application, the Buyer shall
indemnify and hold CTC Union Technologies and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, expenses, and reasonable attorney fees
arising out of, either directly or indirectly, any claim of personal injury or death that may be
associated with such unintended or unauthorized use, even if such claim alleges that CTC Union
Technologies was negligent regarding the design or manufacture of said product.
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful interference in which case the user will
be required to correct the interference at his own expense. NOTICE: (1) The changes or
modifications not expressively approved by the party responsible for compliance could void the
user's authority to operate the equipment. (2) Shielded interface cables and AC power cord, if any,
must be used in order to comply with the emission limits.
CISPR PUB.22 Class A COMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the
following technical standard. EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equipment. This device complies with CISPR
Class A.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
CE NOTICE
Marking by the symbol CE indicates compliance of this equipment to the EMC directive of the
European Community. Such marking is indicative that this equipment meets or exceeds the
following technical standards: EN 55022:2006+A1:2007, Class A, EN55024:2010, and
EN60950-1:2006
3
CTC Union Technologies Co., Ltd.
Far Eastern Vienna Technology Center (Neihu Technology Park)
8F, No. 60, Zhouzi St.
Neihu, Taipei, 114
Taiwan
Phone: +886-2-2659-1021
FAX: +886-2-2799-1355
IEXT224-4PH-L
IEXT224-4PH-R
Long Reach PoE Extenders
User Manual
Version 1.0 July 2015
This document is the current official release manual. Contents are subject to change without prior
notice. Please check CTC Union's website for any updated manual or contact us by E-mail at
sales@ctcu.com. Please address any comments for improving this manual or to point out
omissions or errors to mark[email protected]om. Thank you.
2015 CTC Union Technologies Co.,Ltd.
All Rights Reserved
The contents of this document are subject to change without any prior notice.
Table of Contents
1. PRODUCT INTRODUCTION .............................................................................................................. 5
1.1 DESCRIPTION...................................................................................................................................... 5
1.2 FEATURES .......................................................................................................................................... 5
1.3 SPECIFICATIONS .................................................................................................................................. 6
1.4 APPLICATIONS .................................................................................................................................... 7
1.5 REFERENCE PERFORMANCE DATA ........................................................................................................... 8
2. HW DESCRIPTION ........................................................................................................................... 9
2.1 OVERVIEW ......................................................................................................................................... 9
2.2 PRODUCT OUTLOOK ............................................................................................................................ 9
2.3 LED DEFINITION ............................................................................................................................... 10
2.4 POWER ........................................................................................................................................... 11
2.5 3-POSITION DIP SWITCH .................................................................................................................... 12
3. REGULATORY COMPLIANCE .......................................................................................................... 13
5
1. Product Introduction
1.1 Description
IEXT224-4PH-L & IEXT224-4PH-R Long Reach POE Extenders are designed to extend the
reach of Ethernet Data and IEEE 802.3at Power over Ethernet beyond its natural limitations
of 100 m for the network infrastructure. The solution works in pairs for point to point
connectivity. It features IEXT224-4PH-L Long Reach PoE Extender (CO), the master unit at
the central site that can transmit data and power over a single pair of telephone grade UTP
wire up to 1,200 m or coaxial cable up to 1,800 m. On the receiving end is IEXT224-4PH-R
Long Reach PoE Extender with 4 PoE (PSE) ports (CPE). Without the need for local power
supply, each IEXT224-4PH-R is equipped with four 10/100Base-TX IEEE 802.3at POE Ports for
total power budget of 30W that can support any remote IEEE 802.3at/af powered device (PD)
like Wi-Fi Access Point, IP phone, and IP Camera. It enables centralized management of
power supply from a single location for easy, efficient and cost- effective installation. When
enabling local power supply by dip switch, IEXT224-4PH-R can supply power budget of 30W
to each one of the four POE ports. IEXT224-4PH-L & IEXT224-4PH-R Long Reach PoE
Extenders are an ideal POE extension solution for service providers to deploy networking
applications in public areas that requires Wireless AP, IP Phones and IP Cameras.
1.2 Features
Complies to IEEEE 802.3at POE
Industrial-Grade Extenders for applications in harsh environment
Simultaneous transmission of Ethernet data and POE Power over UTP wire
Centralized management of power supply
Eliminated the need for local power supply at remote sites
Easy cabling for quick installation
Long transmission distance up to 1000 m
Quick deployment and easy maintenance.
Flexible and efficient power management
Automatically switch between VDSL2 Profile 30a and 17a to utilize bandwidth
performance
Dip Switch to enable local power supply and provide full 30W to each of the
four POE ports.
6
1.3 Specifications
Standards Support:
VDSL2 ITU-T G.993.2
VDSL2 Profiles: 17a and 30a
Protocol Support
Transparent bridging to higher layer protocols
Operating Environment
Operating Temperature: -40°C to 75°C
Storage Temperature: -40°C to 85°C
Humidity: 10% - 95% (non-condensing)
Physical
Hardened aluminum case, IP30
Dimensions: 62 x 135 x 106.5 mm
Installation: DIN-Rail, Panel Rack Mounting
Regulatory Compliance
CE
FCC Part 15 Class B
EN60950
Hardware Interfaces:
Terminal Block for Copper Port
BNC Female for Coaxial Port
4 x RJ-45 10/100Base-TX IEEE 802.3at POE
Port
3 Position Dip Switch
Selectable target band plan (Asymmetric or
Symmetric)
Selectable target SNR margin (6dB or 9dB)
Selectable Remote Power (ON) or Local Power
(OFF)
LED Indicators:
Active: System Status
LPWR/RPWR: Local Power/Remote Power
POE: POE Port Status
Available POE Output(Watts): 5/15/30
Line Speed(Mbps): Link/20/40/60/80/100
Power Supply:
Terminal blocks for redundant DC power
inputs
Din connector for external AC to DC adaptor
Input Voltage: 48 to 57 VDC
Power Consumption: 65 Watts maximum
Over current protection
Automatic short protection
7
1.4 Applications
The solution works in pairs for point to point connectivity. It features IEXT224-4PH-L
Long Reach PoE Extender (CO), the master unit at the central site that can transmit
data and power over a single pair of telephone grade UTP wire up to 1,200m or
coaxial cable up to 1,800 m. On the receiving end is IEXT224-4PH-R Long Reach PoE
Extender with 4 PoE(PSE) ports (CPE). Without the need for local power supply,
each IEXT224-4PH-R is equipped with four 10/100Base-TX IEEE 802.3at POE Ports for
total power budget of 30W that can support any remote IEEE 802.3at/af powered
device (PD) like Wi-Fi Access Point, IP Phone, and IP Camera.
Picture 1.1 Remote Power Enable
Picture 1.2 Remote Power Disable
8
1.5 Reference Performance Data
UTP – 24AWG Copper Wire
SNR
6dB
6dB
Profile
Asymmetrical
Symmetrical
Distance
Downstream
Line Rate
(Mbps)
Upstream
Line Rate
(Mbps)
Downstream
Line Rate
(Mbps)
POE output power
300 m
100
100
100
30 W
400 m
95
70
70
20 W
600 m
65
45
45
15 W
800 m
45
27
27
7 W
1,000 m
35
18
18
5 W
1,200 m
20
8
16
4 W
Coaxial Cable
SNR
6dB
6dB
Profile
Asymmetrical
Symmetrical
Distance
Downstream
Line Rate
(Mbps)
Upstream
Line Rate
(Mbps)
Downstream
Line Rate
(Mbps)
POE output power
400 m
100
100
100
30 W
600 m
100
50
80
20 W
800 m
100
50
80
15 W
1000 m
90
50
60
10 W
1,200 m
70
50
50
8 W
1,400 m
35
55
40
35
6 W
1,600 m
30
40
35
30
5 W
1,800 m
35
20
20
4 W
2,000 m
30
15
15
9
2. HW Description
2.1 Overview
IEXT224-4PH-L & IEXT224-4PH-R devices are Long Reach POE Extenders with four
10/100Base-TX IEEE 802.3at POE Ports. This chapter shows the product outlook and
Hardware interfaces.
2.2 Product Outlook
CO Faceplate CPE Faceplate
10
2.3 LED Definition
The LED indicators could provide instant feedback to users; the behaviors of the LED
are given in below table:
LED Name
Indicator/Color
Condition
Local PWR
Green-off
No local input power
Green-on
Local input power received
Remote PWR
Green-off
No power is transmitted over VDSL interface
Green-on
Power is transmitted over VDSL interface
POE (CPE)
Green-off
No power is transmitted over Ethernet port
Green-on
Power is transmitted over Ethernet port
Link
Green-off
VDSL link not link up
slow flashing
VDSL port is under handshaking
Fast flashing
VDSL port has data transmission or reviving
Green-on
VDSL port link up
Line Speed
Green-on
Displays VDSL link speed in Mbps
(100M/80M/60M/40M/20M), if 80M LED is on
then VDSL downstream line speed is in the
range 80Mbps to 100Mbps.
POE Output
(CPE)
Green-on
Displays POE PSE available output power in
Watt(30W/15W/5W) – Remote Terminal Only
RJ-45
Green-on
Ethernet link up and speed is 100M
Green-flashing
Data transmission or receiving
Green-off
Ethernet is no link up
Yellow-on
Ethernet link up and speed is 10M
Yellow-flashing
Data transmission or receiving
Yellow-off
Ethernet is no link up
Table 2-1 LED indications
11
2.4 Power
Input:
- IEXT224-4PH-L (CO): Provide two redundancy local input powers; power
voltage is 48VDC to 57VDC, terminal Block.
- IEXT224-4PH-R (CPE): Provide two redundancy local input powers; power
voltage is 48VDC to 57VDC, terminal Block.
Output:
- IEXT224-4PH-L (CO): Provide 96VDC output to VDSL Line (Remote Power
Feeding) to support remote power to CPE.
- IEXT224-4PH-R (CPE): Ethernet port provide 4-port POE PSE function to
802.3at (30W).
Power Consumption:
- IEXT224-4PH-L (CO): Max. 65W with Remote Power function enable,
provide CPE POE PSE 30W.
- IEXT224-4PH-R (CPE): Max. 45W with Remote Power function enable,
provide CPE POE PSE 30W
Protection:
- Provide Over-Current protection and resettable smart Short-Circuit
protection on both VDSL interface and POE PSE interface.
Two power level output:
- The function is set to detect CPE function.
- When CO cannot detect CPE, output is 48VDC to VDSL line.
- When CO detected that the CPE is successfully connected, POV output is
96VDC to VDSL line.
12
2.5 3-Position DIP Switch
IEXT224-4PH-L & IEXT224-4PH-R are equipped with DIP Switch selection, which can
allow users to select the parameters in order to meet the needs of different
applications. The parameter options should be set identically on both CO and CPE
sides.
Option
Profile
SNR
Remote Power
On
Asymmetrical
6dB
Enable
Off
Symmetrical
9dB
Disable
13
3. Regulatory Compliance
IEXT224-4PH-L & IEXT224-4PH-R are designed to comply with the following
standards
CE
FCC Part 15 Class A
EN60950
14
This page is intentionally left blank.
15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

CTC Union IEXT224-4PH-L User manual

CTC Union
Brand
CTC Union
Model
IEXT224-4PH-L
Category
PoE adapters
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents