Alpic Air CS285U-12F5 User manual

Brand: Alpic Air

Model: CS285U-12F5

Category: Mobile air conditioners

Type: User manual

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Read This Manual

Keep this manual where the operator can easily

find them. Inside you will find many helpful hints

on how to use and maintain your air conditioner

properly. Just a little preventative care on your

part can save you a great deal of time and money

over the life of your air conditioner. You'll find many

answers to common problems in the chart of

troubleshooting tips. If you review the chart of

Troubleshooting Tips first, you may not need

to call for service.

The design and specifications are subject to change without prior notice for

product improvement. Consult with the sales agency or manufacturer for details.

SPLIT-TYPE

CS285U-12F5

16122000A03952

20160715

CONTENTS

DISPOSAL: Do not dispose of this product as unsorted municipal waste. Collection of such waste

separately for special treatment is necessary.

It is prohibited to dispose of this appliance in domestic household waste. For disposal, there are

several possibilities:

A) The municipality has established collection systems, where electronic waste can

be disposed of at least free of charge to the user.

B) When buying a new product, the retailer will take back the old product at least

free of charge.

C) The manufacturer will take back the old appliance for disposal at least free of

charge to the user.

D) As old products contain valuable resources, they can be sold to scrap metal

dealers.

Wild disposal of waste in forests and landscapes endangers your health when hazardous

substances leak into the ground-water and find their way into the food chain.

When using this air conditioner in the European countries, please read the

following information:

SAFETY PRECAUTIONS

NAMES OF PARTS

OPERATING INSTRUCTIONS

CARE AND MAINTENANCE

TROUBLESHOOTING TIPS

Warning .....................................................................................................................................3

Caution ......................................................................................................................................4

Indoor unit ........... .....................................................................................................................5

outdoor unit ...............................................................................................................................5

Indication lamp...........................................................................................................................5

Special functions .......................................................................................................................6

Operating temperature................................................................................................................7

Manual operation ......................................................................................................................7

Airflow direction control ............................................................................................................8

How the air conditioner works ..................................................................................................9

Before maintenance...... ...........................................................................................................10

Cleaning the unit.......................................................................................................................10

Cleaning the air filter and air freshening filter ..........................................................................10

Replacement of the air filter and air freshening filter ...............................................................11

Preparation for extended non-operation....................................................................................11

Pre-season inspection...............................................................................................................11

Normal function of the air conditioner.......................................................................................12

Troubleshooting guide .............................................................................................................14

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

SAFETY PRECAUTIONS

To prevent injury to the user or other people and property damage, the following instructions

must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage.

The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

Meanings of symbols used in this manual are as shown below.

WARNING

Be sure to follow the instructions.

Strictly prohibited.

CAUTION

This symbol indicates the possibility of injury or damage to property.

Do not extend the cable and never use

multiple plugs. A poor electrical connection,

poor insulation or voltage which is higher

than permitted can cause fire.

Do not expose your body directly to the cool

air for prolonged period.

Never poke fingers, sticks or other objects

in the air inlet and outlet vents.

Never attempt to repair, relocate, modify the

air conditioner yourself. Always contact your

service provider if required.

Never pull the plug out by pulling on the

cable. Hold the plug firmly and pull it out of

the plug socket, otherwise there is a risk of

damaging the cable.

Do not operate your air conditioner in a wet

room such as a bathroom or laundry room.

Never actuate any switches with a wet

hand. It may cause an electric shock.

Never use the device for any other

purpose than the intended use. Never

place food, precision instruments, plants,

animals, paint, etc. on the unit.

Do not expose plants or animals directly

to the air flow.

Never clean the air conditioner with water.

Never use combustible cleaning agents

as these could cause a fire or deformation.

Never place any burning objects close to

the device if they could be directly affected

by the emitted air.

Never step onto the outdoor unit and

never place anything on it.

Never use an unsteady or rusty base.

Never install the air conditioner in places

where combustible gas can be emitted.

Emmitted gas may collect and cause an

explosion.

Never allow the air conditioner to run for

too long with the doors or windows open,

or if the humidity is very high.

Remove all dirt from the power plug and

plug it firmly. Soiled plugs can cause fire

or an electric shock.

In the event of any abnormalities such

as smell of burning, immediately switch

off the device and pull the plug. Contact

your service provider.

Always switch off the device and pull the

plug before you start to clean it.

Use specified power cord.

Contact the authorized installer for

installation of this unit.

Contact an authorized service technician

for repair or maintenance of this unit.

This appliance is not intended for use by

persons(including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure

that they do not play with the air

conditioner.

If the air conditioner is to be used in

conjunction with other heaters, the air

should be refreshed periodically, otherwise

there is a risk of lack of oxygen.

Always pull out the power plug if the unit

is not going to be used for any lengthy

period of time. Collections of dust can

cause fire.

Always switch off the air conditioner and

pull out the power plug during a storm,

otherwise, electrical parts may get

damaged.

Check that the drainage line is correctly

connected. If not, water will escape.

Check that the condensation water can

run off unhindered. It may cause water

damage if the condensation water cannot

run off properly.

The air conditoner must be earthed in

accordance with the local codes.

For electrical safety purposes we

recommend that you install an earth-

leakage circuit-breaker.

If the power cord is damaged, it must be

replaced by the manufacturer, its service

agent or similary qualified persons in order

to avoid a hazard.

WARNING

CAUTION

OPERATING INSTRUCTIONS

8. Connecting pipe

9. Connecting cable

10. Stop valve

Outdoor unit

Air inlet(rear)

Air inlet(side)

Air outlet

1. Front panel

2. Air inlet

3. Air filter

4. Air outlet

5. Horizontal air flow grille

6. Vertical air flow louver(inside)

7. Display panel

Indoor unit

RUN indication lamp

This lamp illuminates when the air

conditioner is in operation.

TIMER indication lamp

Lights up during Timer operation.

DEFROST indication lamp

(Enabled on cooling & heating models only):

Lights up when the air conditioner starts

defrosting automatically or when the warm

air control feature is activated in heating

operation.

TEMPERATURE indication lamp

Displays the temperature settings when the

air conditioner is operational.

Displays the malfunction code when fault

occurs .

FRESH indication lamp(optional)

Lights up when Clean Air feature is

activated.

NAMES OF PARTS

Indication lamp

NOTE:

All the pictures in this manual are for

explanation purposes only. The actual shape

of the indoor unit you purchased may be slightly

different on front panel and display window. The

actual shape shall prevail.

Names of parts

(A)

(B)

FRESH DEFROST RUN TIMER

Model B

Model A

Special functions

Improving the quality of indoor air is one

of the purposes of an air conditioner.

This air conditioner is equipped with

ionizer or Plasma Dust Collector(model

dependent). With the anions generated

by Ionizer, the air circulation of the air

conditioner fills the room with refreshing,

natural and healthy air. The Plasma Dust

Collector generates a high voltage

ionization zone, through which the air is

converted to plasma. Inside the air most

of the dust, smoke, and pollen particles

are captured by the electrostatic filter.

CLEAN AIR function(Optional)

Airborne bacteria use the moisture on the

indoor heat exchanger to grow. Regular

drying of the exchanger prevents this

growth. By simply pressing the SELF

CLEAN button, the system will automatically

manage the process. This cleaning action

may be done as frequently as desired.

For cooling models, only the indoor fan is

active in low speed for 30 minutes and the

unit turns off automatically.

For cooling & heating models, the unit will

operate as in the following sequence :

FAN mode at Low fan speed--Heating

operation with LOW fan speed ---FAN

operation--Stop Operation---Turn off.

Note:

This function is only activated in COOLING

or DRY mode.

Before activation the air conditioner, it is

recommended to run the air conditioner

under cooling operation for about 30

minutes.

Pressing the SELF CLEAN or ON/OFF

button again during the cleaning cycle will

cancel the operation and turn the unit off.

SELF CLEAN function(Optional)

Refrigerant Leakage Detection (Optional)

When refrigerant leakage is detected,

the indoor unit will display EC code or

flash LEDs(model dependent).

Louver Angle Memory Function

(optional):

Within the scope of safety angle, the

horizontal louver angle is memorised

and will return to the position last

selected by user. If it exceeds, it will

memorize the boundary of safety angle.

This will not happen when Turbo or

manual control buttons are pressed or

after a power interruption. So we

strongly suggest that the open angle of

the horizontal louver should not be set

too small, in case the condensed water

forms and drips from the horizontal louver.

After 240 hours of operation, the indoor

display window will display and flash CL ,

this feature is a reminder to clean the Air

Filter for more efficient operation. After 15

seconds, the system will revert back to the

previous display again. When the CL

indicator appears and flashes, please

press the LED button on remote controller

for 4 times or press the Manual control

button for 3 or more times to clear the

registered hours, otherwise the CL

indicator will display and flash again for

another 15 seconds at the next time of

tarting the unit.

Cleaning filter reminding function

(Optional)

After 2880 hours of operation, the indoor

display window will display and flash nF ,

this feature is a reminder to replace the Air

Filter for more efficient operation. After 15

seconds, the system will revert back to the

previous display again. When the nF

indicator appears and flashes, please

press the LED button on remote controller

for 4 times or press the Manual control

button for 3 or more times to clear the

registered hours, otherwise the nF

indicator will display and flash again for

another 15 seconds at the next time of

starting the unit.

Replacing filter reminding function

(Optional)

The display panel of the indoor unit

may look like one of the following:

OPERATING INSTRUCTIONS

Airflow direction control

Adjust the air flow direction properly, otherwise it might

cause discomfort or cause uneven room temperatures.

Adjust the horizontal louver using the remote controller.

Adjust the vertical louver manually or using the remote

controller(depending on models).

To set the vertical air flow(Up--Down) direction

Perform this function while the unit is in operation.

Use the remote controller to adjust the air flow

direction. The horizontal louver can be moved at

a range of 6 for each press, or swing up and down

automatically. Please refer to the REMOTE

CONTROLLER OPERATION MANUAL for details.

To set the horizontal air flow direction (left - right)

Move the deflector rod manually to adjust the air flow

in the direction you prefer.

IMPORTANT:Do not put your fingers into the panel of

blower and suction side.The high-speed fan inside may

cause danger.

For some models, the vertical louver can be adjusted

by using the remote controller. Please refer to the

REMOTE CONTROLLER OPERATION MANUAL

for details.

OPERATING INSTRUCTIONS

NOTE: This manual does not include Remote Controller Operations, see the

<<Remote Controller Instruction>> packed with the unit for details.

Operating temperature

Mode

Cooling operation

Heating operation

Drying operation

Temperature

1. Optimum performance will be achieved within these operating temperatures. If air

conditioner is used outside of the above conditions, certain safety protection features

might come into operation and cause the unit to function abnormally.

2. Room relative humidity less than 80%. If the air conditioner operates in excess of this

figure, the surface of the air conditioner may attract condensation. Please sets the vertical

air flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode.

Room temperature

Outdoor temperature

NOTE:

( For the models with low

temperature cooling system

(For special tropical models)

Range

Deflector rod

AUTO/COOL

Suspension bars

AUTO/COOL

(1)

(2)

Units are equipped with a switch to run emergency operation mode. It can be accessed by

opening the front panel. This switch is used for manual operation in case the remote controller

fails to work or maintenance necessary.

Manual operation

Hold the panel sides and lift the front panel

up to an angle until it remains fixed with a

clicking sound. For some models, please

use suspension bars to prop up the panel.

Once you push the manual switch, the

operation mode is shifted in an order as:

AUTO, COOL, OFF. The temperature will

be set at 24 C/76 F and the fan on Auto.

After operation, close the panel firmly to its

original position.

Manual switch

This switch is used for testing purposes

only. You had better not choose it.

To restore the remote controller operation,

use the remote controller directly.

CAUTION:

Do not operate the air conditioner for long periods with

the air flow direction set downward in cooling or

dehumidifying mode. Otherwise, condensation may

occur on the surface of the horizontal louver causing

moisture to drop on to the floor or on furnishings.

When the air conditioner is started immediately after it

was stopped, the horizontal louver might not move for

approximately 10 seconds.

Open angle of the horizontal louver should not be set

too small, as COOLING or HEATING performance may

be impaired due to too restricted air flow area.

Do not move the horizontal louver manually, otherwise

the horizontal louver will be out of sync. Please cease

operating, unplug power for a few seconds,then restart

the air conditioner.

CAUTION

NOTE:

Best working conditions(the energy efficiency can be

affected if not set under these conditions):

The best angle of louvers is the default angle of cooling

mode

The best way of setting the angle of louvers at heating

mode is: run the unit for 5 minutes and then use the

remote controller to set the louvers at the default angle

of cooling mode.

17 C~32 C

(62 )

F~90 F

18 C~43 C

(64 )

F~109 F

18 C~54 C(64 )

F~129 F

18 C~54 C(64 )

F~129 F

11 C~43 C

(52 )

F~109 F

-7 C~24 C

(20 )

F~76 F

-7 C~43 C(20 )

F~109 F

0 C~30 C

(32 )

F~86 F

10 C~32 C

(50 F~90 F)

CARE AND MAINTENANCE

Care and Maintenance

Filter Handle

OPERATING INSTRUCTIONS

How the air conditioner works

1 hour

Set

Temperature

Set

Temperature

Cooling

Heating

SLEEP operation

1 hour

SLEEP operation

7 hours timer off

AUTO operation

When you set the air conditioner in AUTO mode, it will

automatically select cooling, heating(cooling/heating

models only), or fan only operation depending on set

temperature and the room temperature.

The air conditioner will control room temperature

automatically to the temperature point you set.

If you feel uncomfortable in the AUTO mode, you can set

your desired temperature.

SLEEP operation

When you push SLEEP button on remote controller

during cooling, heating(cooling & heating models only),

or AUTO operation , the air conditioner will

automatically increase (cooling) or decrease (heating)

1 C/2 F per hour for the first 2 hours, then hold

steadily for the next 5 hours, after that it will switch off.

This mode saves you energy and brings you comfort

at night.

DRYING operation

The temperature is regulated while dehumidifying by

repeating turning on and off of the cooling operation or

fan only. The fan speed is LOW.

Optimal operation

To achieve optimal performance, please note the

following:

Adjust the air flow direction correctly so that it is not

towards people.

Adjust the temperature to achieve the highest comfort

level. Do not adjust the unit to excessive temperature

levels.

Close doors and windows on COOL or HEAT modes,

or performance may be reduced.

Use TIMER ON button on the remote controller to

select a time you want to start your air conditioner.

Do not put any object near air inlet or air outlet, as the

efficiency of the air conditioner may be reduced and

the air conditioner may stop running.

Clean the air filter periodically, otherwise cooling or

heating performance may be reduced.

Do not operate unit with horizontal louvre in closed

position.

Before mainatenance

A cloth dampened with cold water may be used

on the indoor unit if it is very dirty, after that, the

unit should be dried with a dry cloth.

Do not use a chemically treated cloth or duster to

clean the unit.

Do not use benzine, thinner, polishing powder, or

similar solvents for cleaning. These may cause

the plastic surface to crack or deform.

Never use water hotter than 40 C/104 F to clean

the front panel, it could cause deformation of

discolouration.

CAUTIONS

Turn the system off before cleaning. To clean, wipe with

a soft, dry cloth. Do not use bleach or abrasives.

NOTE: Power supply must be disconnectd before

cleaning the indoor unit.

Cleaning the air filter and air freshening filter

A clogged air filter reduces the cooling efficiency of

this unit. Please clean the filter once every 2 weeks.

1. Lift the indoor unit panel up to an angle until it

stops with a clicking sound.For some models,

please use suspension bars to prop up the panel.

2. Take hold of the handle of the air filter and lift it

up slightly to take it out from the filter holder,

then pull it downwards.

3. Remove the AIR FILTER from the indoor unit.

Clean the AIR FILTER once two weeks.

Clean the AIR FILTER with a vacuum cleaner

or water, then dry it up in cool place.

4. Remove the Air Freshening Filter from its supporting

frame (on some models).

Clean the air freshening filter at least once a

month, and replace it every 4-5 months.

Clean it with vacuum cleaner, then dry it in cool

place.

Air freshen

ing filter

1010

CARE AND MAINTENANCE

The following events may occur during normal operation.

1. Protection of the air conditioner.

Compressor protection

The compressor can't restart for 3-4 minutes after it stops.

Anti-cold air (Cooling and heating models only)

The unit is designed not to blow cold air on HEAT mode, when the indoor heat exchanger is in

one of the following three situations and the set temperature has not been reached.

A) When heating has just started.

B) Defrosting.

C) Low temperature heating.

The indoor or outdoor fan stop running when defrosting (Cooling and heating models only).

Defrosting (Cooling and heating models only)

Frost may be generated on the outdoor unit during heat cycle when outdoor temperature is low

and humidity is high resulting in lower heating efficiency of the air conditioner.

During this condition air conditioner will stop heating operation and start defrosting automatically.

The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature and

the amount of frost built up on the outdoor unit.

2. A white mist coming out from the indoor unit

A white mist may generate due to a large temperature difference between air inlet and air outlet

on COOL mode in an indoor environment that has a high relative humidity.

A white mist may generate due to moisture generated from defrosting process when the air

conditioner restarts in HEAT mode operation after defrosting.

3. Low noise of the air conditioner

You may hear a low hissing sound when the compressor is running or has just stopped running.

It is the sound of the refrigerant flowing or coming to a stop.

You can also hear a low "squeak" sound when the compressor is running or has just stopped

running. This is caused by heat expansion and cold contraction of the plastic parts in the unit

when the temperature is changing.

A noise may be heard due to louver restoring to its original position when power is turned on.

4. Dust is blown out from the indoor unit.

This is a normal condition when the air conditioner has not been used for a long time or during first

use of the unit.

5. A peculiar smell comes out from the indoor unit.

This is caused by the indoor unit giving off smells permeated from building material, from furniture,

or smoke.

6. The air conditioner turns to FAN only mode from COOL or HEAT mode (For cooling and

heating models only) .

When indoor temperature reaches the temperature setting on air conditioner, the compressor will

stop automatically, and the air conditioner turns to FAN only mode. The compressor will start again

when the indoor temperature rises on COOL mode or falls on HEAT mode (For cooling and heating

models only) to the set point.

Preparation for extended non-operation

Pre-season inspection

If you plan to idle the unit for a long time, perform

the following:

(1) Clean the indoor unit and filters.

(2) Operate the fan for about half a day to dry the

inside of the unit.

(3) Stop the air conditioner and disconnect power.

(4) Remove the batteries from the remote controller.

The outdoor unit requires periodic maintenance

and cleaning. Do not attempt to do this yourself.

Contact your dealer or service provider.

Check that the wiring is not broken off or

disconnected.

Clean the indoor unit and filters.

Check that the air filter is installed.

Check if the air outlet or inlet is blocked after the

air conditioner has not been used for a long time.

Do not touch the metal parts of the unit when

removing the filter. Injuries can occur when

handling sharp metal edges.

Do not use water to clean inside the air conditioner.

Exposure to water can destroy the insulation,

leading to possible electric shock.

When cleaning the unit, first make sure that the

power and circuit breaker are turned off.

Do not wash air filter with hot water at more than

40 C . Shake off moisture completely and dry

it in the shade. Do not expose it directly to the sun,

it may shrink.

/104 F

Caution

5. Install the air freshening filter back into position.

6. Insert the upper portion of air filter back into the

unit, taking care that the left and right edges line

up correctly and place filter into position.

Replacement of air filter and air freshening filter

1. Remove the air filter.

2. Remove the air freshening filter.

3. Install a new air freshening filter.

4. Reinstall the air filter and securely close the front

panel.

Normal function of the air conditioner

TROUBLESHOOTING TIPS

1111

1212

TROUBLESHOOTING TIPS

Malfunctions

Unit does not

start

Unit not cooling

or heating

(Cooling/ heating

models only)

room very well

while air flowing

out from the air

conditioner

Cause

Power cut

Unit may have become unplugged

Fuse may have blown.

Battery in Remote controller may

have been exhausted.

The time you have set with timer

is incorrect.

Wait for power to be restored.

Check that plug is securely in wall

receptacle.

Replace the fuse.

Replace the battery.

Wait or cancel timer setting.

Set temperature correctly. For

detailed method please refer to

"Using remote control" section.

Clean the air filter.

Close the doors or windows.

Clear obstructions away first, then

restart the unit.

Wait.

Inappropriate temperature

setting.

Air filter is blocked.

Doors or Windows are open.

Air inlet or outlet of indoor or

outdoor unit has been blocked.

Compressor 3 or 4 minutes

protection has been activated.

If the trouble has not been corrected, please contact a local dealer or the nearest customer

service center. Be sure to inform them of the detailed malfunctions and unit model number.

Notes: Do not attempt to repair the unit yourself.

Always consult an authorized service provider.

What should be done?

TROUBLESHOOTING TIPS

Troubleshooting guide

8. Dripping water may generate on the surface of the indoor unit when cooling in a high

relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to

the maximum air outlet position and select HIGH fan speed.

9. Heating mode (For cooling and heating models only)

The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit

during heating operation. When the outdoor temperature falls, heat drawn in by the air

conditioner decreases accordingly. At the same time, heat loading of the air conditioner

increases due to larger difference between indoor and outdoor temperature. If a

comfortable temperature can't be achieved by the air conditioner, we suggest you use a

supplementary heating device.

10. Auto-restart function

Power failure during operation will stop the unit completely.

For the unit without Auto-restart feature, when the power restores, the OPERATION indicator

on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the

remote controller. For the unit with Auto-restart feature, when the power restores, the unit

restarts automatically with all the previous settings preserved by the memory function.

7.The air conditioner runs function after turning off the unit.

When turning off the unit under COOL(AUTO COOL, FORCED COOL) and DRY mode, the air

conditioner will run function for 7-10 minutes, then stop the operation and turn

off the unit automatically.

Anti-mildew

Fuse blows frequently or circuit breaker trips

frequently .

Other objects or water fall into the air conditioner.

Terrible odors are smelled or abnormal sounds

are heard.

Trouble

OPERATION(RUN) indicator or other

indicators continue flashing.

If one of the following code appears on the

display area : E0,E1,E2,E3.....or P0,P1,P2,

P3...., or F1,F2,F3.......

The unit may stop operation or continue to

run in a safety condition (depending on

models). Waiting for about 10 minutes, the

fault may be recovered automatically, if

not, disconnect the power and then

connect it in again. If the problem still

exists, disconnect the power and contact

the nearest customer service center.

Stop the air conditioner immediately,

disconnect the power and contact the

nearest customer service center.

Displays the special functions in the following ways(for some models only):

Displays for three seconds when Timer ON, Fresh, Swing, Turbo

or Silence feature is activated.

Displays for three seconds when Timer OFF is set.

Displays for three seconds when Fresh, Swing, Turbo or Silence

feature is cancelled.

Displays under defrosting operation.

Displays when anti-cold air feature is

activated under heating mode.

Displays during self clean operation(if applicable).

Displays under 8 C heating operation(if applicable).

11. Special function display

1313

1414

Alpic Air CS285U-12F5 User manual

Brand: Alpic Air

Model: CS285U-12F5

Category: Mobile air conditioners

Type: User manual

Download PDF

report

Alpic Air CS285U-12F5 User manual

Alpic Air CS285U-12F5 User manual

Other documents