®
®
Slip -
Resistant
Additive
Add to any “Coating-Type”
Sealer or Paint to Increase
Slip Resistance. May be
used with water based or
solvent based paint.
Professional Results...GUARANTEED!
800-486-1414 • www.glaze-n-seal.com
Treats up to
1-Gallon
Treats up to
5-Gallons
Ideal for Plain & Decorative Concrete,
Unglazed Tile, Stone, Masonry & Brick
• Mixes easily • Easy to Use
• Stays suspended in Sealer • Long Wearing
• Will Not Alter Sealer Appearance
GRIP ’N SEAL
®
®
Quality Products for Concrete, Tile and Masonry
Glaze ’N Seal Products Inc., Irvine, CA • www.glaze-n-seal.com
FS38/0116
GRIP ’N SEAL
SLIP RESISTANT
ADDITIVE
damages resulting from the use of the product. Determining the
suitability of the product for any intended use shall be solely
the responsibility of the user. ALWAYS TEST FIRST.
CAUTION: Avoid breathing dust. Contact with eye and skin may
cause irritation. DO NOT INGEST. Grip ’N Seal is not hazardous,
but should be treated as a nuisance dust while mixing. Use with
adequate ventilation, or wear an appropriate, properly fitted
respirator (NIOSH/MSHA approved) during mixing. If dizziness,
headache or eye watering occurs, get to fresh air. Keep con-
tainer closed when not in use. If spillage occurs, absorb and
dispose of, according to local regulations.
KEEP OUT OF REACH OF CHILDREN
DO NOT TAKE INTERNALLY
FIRST AID: If swallowed get medical attention immediately. DO
NOT induce vomiting. In case of eye contact, flush with plenty
of water for at least 15 minutes. Get medical attention if irrita-
tion persists. For skin contact wash thoroughly with soap and
water.
This product does not meet the definition of a hazardous substance
or preparation as defined by 29 CFR 1910. 1200 or the European
Union Council Directives 67/548/EEC, 1999/45/EC, 1272/2008/EC and
subsequent Directives.
DESCRIPTION: Glaze ’N Seal’s Grip ’N Seal is a unique micron-
ized polymer which when mixed with a coating type sealer
or paint creates a textured, slip resistant surface without a
sharp abrasive finish. Use on driveways, patios, garage floors,
walkways, steps and pool areas.
Mixes easily with any Glaze ’N Seal coating sealer.
EASY TO USE:
• Stays suspended in sealer.
• Long wearing.
• Will not alter sealer appearance.
USES: Grip ’N Seal additive can be used with these Glaze ’N
Seal Products.
• “Wet Look” Green • Paver Sealer
• “Wet Look” 2000 • Slate Sealer
• Original “Wet Look” • Olé Mexican Tile Sealer
• “Wet Look” WB • Multi-Purpose Sealer
(May also use with water based or solvent-based paint.)
ALWAYS TEST when using to insure suitable application and
satisfactory results.
INSTRUCTIONS FOR USE
• Add a full 12 ounce container of Grip ’N Seal Additive to a
five gallon pail of sealer or paint. For one gallon of sealer or
paint, use two ounces of Grip ‘N Seal Additive. Mix well.
• Apply sealer as normal. Use of gartden-type sprayer, lambs
wool applicator or brush is recommended.
• Stir occasionally during use to insure an even dispersion.
IMPORTANT NOTICE TO CUSTOMERS:
Since the use of this product is beyond the control of either
seller or manufacturer, their only obligation shall be to replace
any quantity of product, which is proven defective. They cannot
assume any risk or liability for results obtained, nor can they
accept damages in excess of the purchase price of the product
itself, which does not include labor or any consequential
ADD TO “COATING” TYPE SEALER OR
PAINT TO INCREASE SLIP RESISTANCE
MADE IN USA GLAZE-N-SEAL.COM
/
