ANZZI K36203A-108 Installation guide

Brand: ANZZI

Model: K36203A-108

Type: Installation guide

General Recommendations:

Tools and Materials needed:

Please read installation and maintenance instructions thoroughly.

Inspect your sink for any noticeable damage before installation.

Check all local applicable plumbing and building codes.

These instructions are based on application to composite material or solid surface countertop

installation only; countertop application to stone, marble, granite or butcher-block should be referred to

an experienced countertop fabricator for custom installation.

Because Farmhouse sinks are individually handmade, we suggest using experienced and

professional installers only. For custom cutting of countertop and installation of the actual sink, on-site

installation is also recommended. Acceptable variances are approximately 1/8 of an inch. Alignment to

the cut-out and precise application and trimming of any adhesive sealant are critical to a superior ﬁt and

ﬁnished look. Please take extra care in this regard.

Farmhouse sinks require custom order cabinets. Consult your cabinet dealer.

Be sure to use proper tools and always wear personal safety devices for your protection.

Tape Measure

Hacksaw / Jigsaw

Rags

Pencil (NOT ink)

Framing Square

Ear Protection

Shims

Denatured Alcohol

Eye Protection

Silicone Adhesive Sealant

Wood Braces

We do not accept any liability for damage to countertop, sink fixture, faucets or personal injury

during installation. Warranty is void if installation instructions are not followed.

ANZZI

Perfection is our Tradition™

For more information visit us at www.ANZZI.com

or call us at 1-844-44-ANZZI

Farmhouse Kitchen Sink Installation Guide

Installation Options:

Farmhouse sinks offer installation options depending on your design.

Caution: All installation types need to allow room for faucet installation. Ensure adequate clearance behind

the sink for any faucet and backsplash, as well as full range of motion for faucet spouts and handles.

Undermount Installation

Typical undermount installation with 1/4" reveal recommended.

Typical flush mount and built-up installation

Built-up installation may expose sink sides to be raised up to 1" above the countertop.

Flush mount Installation Built-up Installation

1. Prepare the Sink Base Cabinet:

Farmhouse sinks offer installation options depending on your design.

Farmhouse sinks require custom order sink base cabinets with a front cutout to accommodate a 10" deep

sink. Build a plywood platform on a support frame inside of the sink base cabinet. Platform must support the

weight of the sink and any attachments such as garbage disposals. When the sink is placed onto a platform,

make sure the top of the sink is evenly flush against the bottom of the countertop. Allow clearance for water

supply line and drains or garbage disposal, as necessary.

Set the sink on top of the cabinet or into the cabinet front cutout. Apply sealant if necessary as a gasket

between the sink and cabinet.

2. Make a Template and Cutout

3. Set the Sink

Carefully clean bottom of countertop and top flange of sink with denatured alcohol. Apply bead of silicone

adhesive (not supplied) around the top edge of the sink. Place countertop onto the sink. Remove excess

sealant from the lip or any surfaces with a cleaner recommended by manufacturer of adhesive sealant.

4. Install the Countertop

Depending on the installation option, make

proper cutout of the countertop.

We recommend a 1/4" reveal on 3 sides

when installed undermount style. For a flush

mount or built up installation, cut countertop along

with outside line of the sink proﬁle. Front end of

Farmhouse sinks are designed to be installed 3/4”

extended out beyond the front end of the countertop. Cut

countertop accordingly. No template is provided due to the custom

nature of each application and installation. The actual sink is used

as the template guide for each installation. After centering the sink

and allowing for any faucets and backsplashes, use a pencil

to outline the sink as your guide for the cutout, allowing for any

reveal before the actual cutting.

out,

ANZZI K36203A-108 Installation guide

ANZZI K36203A-108 Installation guide

ANZZI K36203A-108 Installation guide

Related papers

Other documents